4
Reset
4
eth4 | eth5eth4 | eth5eth2 | eth3eth0 | eth1 eth6 | eth7
Console
Power
HDD
Reset
TP Ethernet interfaces eth0 - eth7
a
Connect the eth0 - eth7 TP Ethernet interfaces with the enclosed
Ethernet cable to your conguration PC or other networking components. Initial setup advice can be found in the supplied quick
install guide.
eth4 | eth5eth4 | eth5eth2 | eth3eth0 | eth1 eth6 | eth7
a
Console
Power
Reset
HDD
b
d
c
Reset button (for powering on the device)
d
After having set the power switch on the device’s rear side
to the “I” position, turn on the device by shortly pressing the
button with a pointed device (e.g. a paper clip).
Pressing the button for 5 seconds shuts down the device.
a LEDs eth0 - eth7 - TP Ethernet
Both off No networking device attached
Left green ickering
Right orange,
permanently
Left green, ickering
Right green,
permanently
Left green, ickering
Right off
Data transfer 1000 Mbps
Data transfer 100 Mbps
Data transfer 10 Mbps
a
b
b LEDs Power / HDD / Reset
Power off Device switched off
Power green Device operational
HDD off no HDD read-/write access
HDD red ickering HDD read-/write access
Hardware
Power supply Internal power supply unit (100–240 V, 50–60 Hz)
Power consumption 150 W max.
Environment Temperature range 0–40 °C; humidity 20–90 %; non-condensing
Housing Robust metal housing, 1 HU with mounting brackets for 19“ installation,
network connectors on the front
Fans 2
Dimensions (mm) 438 x 44 x 292 (W x H x D)
Interfaces
ETH 8x 10 / 100 / 1000 Mbps Gigabit Ethernet ports
USB 2x USB 2.0 ports
Console RJ45 conguration interface
Declaration of conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, and 2011/65/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.lancom-systems.com/ce/
Package content
Documentation Quick Reference Guide (DE, EN), Quick Install Guide (DE, EN), Service & Support Guide (DE, EN)
Accessories 1 Ethernet cable; 1 IEC power cord; 1 serial conguration cable;
2 19” brackets for rack mounting
LANCOM R&S®UF-300
Quick Reference Guide
Conguration interface RJ45 (Console)
b
Maintenance interface for expert conguration
USB 2.0 interfaces
c
Interfaces for software re-installation
e f
Cloud-ready
Please observe the following when setting up the device
A The mains plug of the device must be freely accessible.
A Do not rest any objects on top of the device and do not stack multiple devices.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
Power connector (rear side)
e
Connect the power cable to the device. After having supplied
power the device can be switched on using the power switch.
Power switch (rear side)
f
After having connected the power cable on the device’s rear
side, set the power switch to the “I” position.
A Keep the ventilation slots on the side of the device clear of obstruction.
A Mount the device into a 19” unit in a server rack using the provided mounting accessories.
MOUNTING AND CONNECTING THE DEVICE
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document
contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111832/0720
TECHNICAL DATA
Loading...