Page 1
Gigabit Ethernet 10/100/1000
ISDN 1 ISDN 2
TE / NT NT
VDSL
Analog 1Analog 2
MOUNTING AND CONNECTING THE DEVICE
TECHNICAL DETAILS
LANCOM R883VAW
LANCOM R883VAW
DSL
ETH 2
Power
ETH 1
Online
ISDN 1
ETH 4
ETH 3
VPN
Analog 1
Analog 2
ISDN 2
WLAN
Reset
VoIP
Quick Reference Guide
4
Please observe the
following when setting
up the device
a For devices to be
operated on the
desktop, please attach
the adhesive rubber
footpads
a Do not rest any objects
on top of the device and
do not stack multiple
devices
Power
a Keep the ventilation
slots on the side of
the device clear of
obstruction
a In case of wall
mounting, use the
drilling template as
supplied
a Rack installation with
the optional LANCOM
Rack Mount (not
supplied)
Hardware
Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection
Power consumption Max. ca. 14 W
Environment Temperature range 0–35 °C; humidity 0–95 %; non-condensing
Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures
Number of fans None; fanless design, no rotating parts, high MTBF
a c eb gfd ih j
a b c d e f
LANCOM 1681V
VDSL
ISDN Status
ETH 2
VPN
ETH 3
ETH 4
Online
ETH 1
VDSL interface
Use the supplied DSL
cable for the IP-based
line to connect the VDSL
interface and the
provider's telephone
socket. For more information, please contact
your Internet service
provider.
ba
Ethernet interface
Use the cable with the
green-colored connectors
to connect one of the
interfaces ETH1 to ETH4
to your PC or a LAN
switch.
c
Analog interface
Connect analog terminal
devices to the analog
interfaces either directly
via RJ11 or with the
help of the enclosed TAE
adapter.
d e f g
Serial interface
Conguring the device
via the serial interface
requires a serial
con guration cable
(available separately).
ISDN interface
ISDN 1
Internal (NT) or external
(TE) ISDN bus.
This feature is controlled
by LCOS.
ISDN 2
Internal (NT) ISDN bus.
A 100-Ohm resistor for
line termination is
switchable in LCOS.
USB interface
You can use the USB
interface to connect a
USB printer or a USB
drive.
g
Power
When connecting the
cable to the device, turn
the bayonet connector
90° clockwise until it
clicks into place.
Use only the supplied
power adapter.
a Power
Off Device switched off
Green, permanently Device operational
Red/green blinking Conguration password not set. Without a
conguration password, the conguration
data in the device is unprotected.
Red blinking Charge or time limit reached
b Online
Off WAN connection inactive
Green, permanently WAN connection active
Red, permanently WAN connection error
c DSL
Off Interface deactivated
Green, permanently DSL connection active
Green, ickering DSL data transfer
Red, ickering DSL transfer error
Red/orange, blinking DSL hardware error
Orange, blinking DSL training
Orange, permanently DSL sync
Green, blinking DSL connecting
d Analog
Off Interface deactivated
Green, permanently Interface activated
Orange, blinking Incoming call
Green, blinking Connection active
e ISDN
Off Interface deactivated
Green, permanently D-channel active
Green, ickering ISDN data transfer
Red, ickering ISDN transfer error
Red/orange, blinking ISDN hardware error
f ETH
Off No networking device attached
Green, permanently Connection to network device operational,
Green, ickering Data transmission
no data trafc
g WLAN
Off No Wi-Fi network dened or Wi-Fi module
Green, permanently At least one Wi-Fi network is dened and
Green, blinking DFS scanning or other scan procedure
deactivated. The Wi-Fi module is not
transmitting beacons.
Wi-Fi module activated. The Wi-Fi module
is transmitting beacons.
h VoIP
Off No SIP accounts dened or VCM is off
Green, permanently All dened and active SIP accounts
Red, permanently Not all dened and active SIP accounts
Red or green,
inverse ashing
(outgoing) were successfully registered
were registered (possibly still in process)
Number of currently used lines (connecting
or connected)
i VPN
Off VPN connection inactive
Green, permanently VPN connection active
Green, ashing VPN connecting
j Reset
Reset switch
Operated e.g. with a paper clip
a short press: Restart the device
a long press: Reset the device
Interfaces LANCOM R883VAW over ISDN
WAN: VDSL2 a VDSL2 as per ITU G.993.2; proles 8a, 8b, 8c, 8d, 12a, 12b, 17a;
Wi-Fi a Frequency band: 2400-2483.5 MHz (ISM) or 5150-5825 MHz (restrictions vary between
ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode.
USB USB 2.0 hi-speed host port for connecting USB printers (USB print server),
ISDN 1 / ISDN 2 ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS. According to
Analog 1 / Analog 2 Use the cable of your analog devices to connect them with the analog interfaces. If necessary,
Cong (Com) / V.24 Serial conguration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for
WAN protocols
VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without
ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD
Declaration of Conformity
Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/
Package content
Manual Quick Reference Guide (DE/EN); Installation Guide (DE/EN)
Cable 1 Ethernet cable, 3m (kiwi colored connectors); 1 DSL cable for an IP-based line, 4.25m;
Adapters 2 TAE adapters (RJ11 - TAE)
Power adapter External power supply adapter (230 V); NEST 12 V / 1.5 A DC/S; barrel connector 2.1 / 5.5 mm
This product contains separate open-source software components which are subject to their own licenses, in particular
the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s
WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the
corresponding software components will be made available on a download server upon request.
210 x 45 x 140 mm (W x H x D)
a Compatible to VDSL2 from Deutsche Telekom
a ADSL conformity according to: ADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO,
ADSL2 over ISDN as per ITU G.992.3 Annex B, ADSL over ISDN as per ITU G.992.1 Annex B.
a Supports just one virtual connection at a time in ATM (VPI-VCI pair)
countries)
a Radio channels 2.4 GHz: Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)
a Radio channels 5 GHz: Up to 26 non-overlapping channels (channels available vary
according to country regulations; DFS for automatic dynamic channel selection required)
Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically
disabled in the LCOS conguration.
serial devices (COM-port server) or USB drives (FAT le system)
the settings, connect the light-blue ISDN cable either to the NTBA or the ISDN terminal device.
ISDN 2: Internal (NT) ISDN bus. Use the light-blue ISDN cable to connect the ISDN device to
the ISDN interface.
use the enclosed adapter.
optional connection of analog/GPRS modems. Supports internal COM-port server and provides
transparent asynchronous serial-data transfer via TCP.
DHCP), RIP-1, RIP-2, VLAN
1 ISDN cable, 3m (light-blue connectors)
bayonet; LANCOM item no. 111301
LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered
trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111641/0717
Loading...