4
LANCOM LX-6400
LANCOM LX-6402
Quick Reference Guide
a a
Wi-Fi antenna connectors (only LX-6402)
a
Screw the supplied Wi-Fi antennas onto the dedicated
connectors.
Serial interface
b
You can optionally congure the device by connecting it to
a PC with a conguration cable (separately available).
Reset button
c
Pressed up to 5 seconds: device restart
Pressed longer than 5 seconds:
conguration reset and device restart
b d
c
2.5G
ETH1 (PoE)ETH2ResetConfig (Com) DC 12 V
USB
e f
Power
d
After connecting the cable to the device, turn the connector
90° clockwise to prevent it from accidental un plugging. Use
only the supplied power adapter.
Ethernet interfaces
e
Use the cable with the Ethernet connectors to connect interface
ETH1 (PoE) or ETH2 to your PC or a LAN switch.
USB interface
f
Connect compatible USB devices either directly to the USB
interface, or use a suitable USB cable.
a Power
Off Device switched off
Green, permanently* Device operational,
Blue / red,
alternatingly blinking
1x green inverse
blinking*
2x green inverse
blinking*
3x green inverse
blinking*
resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible.
DHCP error or DHCP server not accessible
(only when congured as DHCP client)
Connection to the LMC active, pairing OK,
claiming error.
Pairing error, resp.
LMC activation code / PSK not available.
LMC not accessible, resp.
communication error.
a b
b WLAN Link
Off No Wi-Fi network dened or Wi-Fi module
deactivated. The Wi-Fi module is not
transmitting beacons.
Green, permanently At least one Wi-Fi network dened and
Wi-Fi module activated. The Wi-Fi module
is transmitting beacons.
Green, inverse ashing Number of ashes = number of connected
Wi-Fi stations
Green, blinking DFS scanning or other scan procedure
Red, blinking Wi-Fi module hardware error
Hardware
Power supply 12 V DC, external power adapter (110 V or 230 V) with bayonet connector to secure against
Power consumption Max. 22 W via 12 V / 2.5 A power adapter (value refers to the total power consumption of
Environment Temperature range 0–40 °C
Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures
Number of fans None; fanless design, no rotating parts, high MTBF
Wi-Fi
Frequency band 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries)
Radio channels
2.4 GHz
Radio channels 5 GHz Up to 19 non-overlapping channels (automatic dynamic channel selection required)
Interfaces
ETH1 (PoE) 10 / 100 / 1000 / 2.5G Base-T; PoE adapter compliant to IEEE 802.3at required
ETH2 10 / 100 / 1000 Base-T
Serial interface Serial conguration interface / COM-port (8-pin mini-DIN): 115,000 baud
Declaration of Conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this radio equipment is
in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: www.lancom-systems.com/ce/
Package content
Documentation Installation Guide (DE / EN), Quick Reference Guide (DE / EN)
Antennas
(only LX-6402)
Cable Ethernet cable, 3 m
Power adapter External power adapter, NEST 12 V / 2.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,
disconnection, or PoE based on 802.3at via ETH1
access point and power adapter),
Max. 24 W via PoE (value solely refers to the power consumption of the access point)
Access point overheating is avoided by automatic throttling of the Wi-Fi modules.
Humidity 0-95 %; non-condensing
205 x 42 x 205 mm (W x H x D)
Up to 13 channels, max. 3 non-overlapping (2.4 GHz band)
Four 3dBi dipole dual-band antennas
LANCOM item no. 111760 (EU, 230 V) (not for WW devices)
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks
of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for
technical errors and / or omissions. 111856/1119
Cloud-ready
Please observe the following when setting up the device
A The mains plug of the device must be freely accessible.
A For devices to be operated on the desktop, please attach the adhesive rubber
footpads.
A Do not rest any objects on top of the device and do not stack multiple devices.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
A Keep all ventilation slots of the device clear of obstruction.
A Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN)
(available as an accessory)
MOUNTING AND CONNECTING THE DEVICE
*) The additional power LED statuses are displayed in 5-seconds
rotation if the device is congured to be managed by the LANCOM
Management Cloud.
TECHNICAL DETAILS
Loading...