Contents
Language Page
___________________________________________________________________
English |
1 |
French
Spanish
1
This product offers: INSTANT TRANSMISSION is the state-of-the-art new wireless transmission technology, exclusively
designed and developed by LA CROSSE TECHNOLOGY. INSTANT TRANSMISSION offers you an immediate update (every 27.5 seconds!) of all your outdoor data measured from the transmitters: follow 
your climatic variations in real-time!
INVENTORY OF CONTENTS
1.Wireless Temperature Station
2.Wireless Temperature Sensor (TX38U) and mounting bracket.
3.Instruction Manual and Warranty Card.
ADDITIONAL EQUIPMENT (not included)
1.1 Philips screwdriver.
2.2 Fresh “AAA” IEC LR3, 1.5V Alkaline Batteries
3.2 Fresh “AA” IEC LR6, 1.5V Alkaline Batteries.
3
TABLE OF CONTENTS |
|
|
|
|
|
|
Topic |
Page |
|
Inventory of Contents |
|
|
Features |
|
|
Setting Up |
|
|
Battery Installation |
|
|
Function keys |
|
|
LCD Screen and Settings |
|
|
Manual Settings |
|
|
Weather Forecast and Tendency |
|
|
Indoor Temperature Display and Indoor MIN/MAX Records |
|
|
Outdoor Temperature Display and Outdoor MIN/MAX Records |
|
|
915 MHz Reception |
|
|
Mounting |
|
|
Troubleshooting |
|
|
Maintenance and care |
|
|
Specification |
|
|
Warranty Information |
|
2 |
|
|
FEATURES:
The Temperature Station
|
Hanging hole |
|
LCD |
Battery |
|
Display |
||
compartment |
||
|
||
|
cover |
|
Function |
Foldout |
|
Keys |
||
Stand |
||
|
Temperature display in degrees Fahrenheit (°F)
Indoor and Outdoor temperature display with MIN/MAX recording
All MIN/MAX recordings can be reset
Low battery indicator
Wireless transmission at 915 MHz
4
Outdoor signal reception intervals at 27.5-second
Table standing or wall mounting
The Outdoor Temperature Transmitter
Remote transmission of outdoor temperature to
Temperature Station by 915 MHzShower proof casing
Wall mounting case
Mounting at a sheltered place. Avoid direct rain and sunshine
SETTING UP:
NOTE: The temperature station will receive only outdoor transmitter only.
5
not successful the reception is tried for 22 seconds on 910MHz. This will also be done for re-synchronization.
INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER
The Temperature Transmitter uses 2 x AAA, IEC LR3, 1.5V battery. To install and replace the batteries, please follow the steps below:
1.Pull out the battery holder at the bottom of the transmitter.
2. Insert the batteries, observing the correct polarity (see
marking).
3. Replace the battery holder on the unit.
Note:
In the event of changing batteries in any of the units, all units
need to be reset by following the setting up procedures. This is because a random security code is assigned by the transmitter at
start-up and this code must be received and stored by the Weather station in the first 3 minutes of power being supplied to it
7
1.First, insert the batteries into the Temperature transmitter. (see “Install and replace batteries in the Temperature transmitter“).
2.Immediately after and within 2 minutes, insert the batteries into Temperature station (see “Install and replace batteries in the Temperature station”). Once the batteries are in place, all segments of the LCD will light up briefly. Then the indoor temperature will de display. If these are not displayed after 60 seconds, remove the batteries and wait for at least 10 seconds before reinserting them.
3.After inserting the batteries into the transmitter, the Temperature station will start receiving data from the transmitter. The outdoor temperature and the signal reception icon should then be displayed on the Temperature station. If this does not happen after 3 minutes, the batteries will need to be removed from both units and reset from step 1.
4.In order to ensure sufficient 915 MHz transmission however, this should under good conditions be a distance no more than 330 feet (TBC) (100 meters-TBC) between the final position of the Temperature Station and the transmitter (see notes on “Mounting” and “915 MHz Reception”).
Note:
If the signal reception is not successful on the first frequency (915MHz) for 22 seconds, the frequency is changed to 920MHz and the learning is tried another 22 seconds. If still
6
INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION
The Temperature station uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the
batteries, please follow the steps below:
1. Remove the cover at the back of the
weather station.
2. Insert batteries observing the correct
polarity (see marking).
3. Replace compartment cover.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on an annual basis to ensure optimum accuracy of these units.
Please participate in the preservation of the environment. Return used batteries to an authorised depot.
8
Loading...