
POWER AMPLIFIER
fP 2200
KEY FEATURES:
2 ✕ 350 watts @ 8 Ω
2 ✕ 650 watts @ 4 Ω
2 ✕ 1100 watts @ 2 Ω
(Measured just below clip level,
with both channels driven)
◆ Compact design, 2U high
◆ Low weight, 7.9 kg (17 lbs)
®
◆ Intercooler
front-to-rear airflow
cooling system with
NEW FEATURES:
◆ Multiple position gain switch
◆ Easily accessible dust filters
◆ Improved low-end power
bandwidth
◆ Link connector with XLR-type
connector
◆ Bridged mono outputs in one
Speakon
◆ Extruded front panel for
increased stability
®
connector
The fP 2200 is a lightweight and space-saving power amplifier, ideal for use
in high quality touring sound systems as well as in demanding permanent
installations.
The latest semiconductor technology is utilized in the new ferrite Power (fP) amplifiers.
This, together with Lab.gruppen’s proprietary copper cooling system, Intercooler®,
enhances the 2 ohms capability. Two easily accessible dust filters on the front ensure a
clean front-to-rear airflow.
A new Bi-phase wiring scheme also increases the capacity of the switch mode power
supply. This extends the power bandwidth in the low end.
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of
features to make the fP family functional in all situations from installation to high performance live sound systems:
Regulated switch mode power supply
Today there are many lightweight, switch-mode amplifiers in the market. However, the
unique Lab.gruppen switch mode power supply technology offers a number of essential
advantages that make it superior to other seemingly similar power supply designs.
The most important features are the regulated power supply and the extreme power
efficiency. The regulated power supply easily deals with a very high variation in the AC
mains voltage: it can drop by up to 20% below its nominal level - e.g. to 180 V (90V)
instead of 230 V (115V) - without any problem. Perhaps even greater benefits result from
the extreme efficiency of Lab.gruppen amplifiers: only a fraction of the energy from the
AC mains is turned into heat.
A regulated power supply also presents some other sonic advantages, such as better
cone control and the same fast response as a conventional power supply
Multiple positions Gain switch
To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a
multiple position gain DIP switch. The maximum amplifier gain can be set to all industry
standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.
Sophisticated protection circuitry, combining:
– ALS™ short circuit protection; the Adaptive Limiting System permits very high peak
currents, but keeps the amplifier within the Safe Operation Area.
– DC protection; protects against infrasonic signals.
– VHF protection; protects the loudspeakers against strong very high frequency non-
musical signals above the audible range.
– Thermal protection; prevents the amplifier from being overheated. The protection
indicators on the front panel are switched on, as a warning, before the protection
process is initiated.
– AC protection; shuts down the power supply if the line voltage is outside the
operating voltage.
– Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers,
whilst maintaining full peak power.

SPECIFICATIONS
fP 2200
Max output power
1)
EIA FTC
at 1 kHz and 1% THD 20–20 kHz at 0.1% THD
MLS-switch –3 dB 0 dB Full
8 Ω per channel 350 W 340 W
4 Ω per channel 650 W 630 W
2 Ω per channel 1100
3)
, 1175
W 950
2)
W
2)
8 Ω bridged 1400 W 1300 W
4 Ω bridged 2200
2)
W 1900
2)
W
Max output voltage
8 ohms load, MLS @ 0 dB 53 Vrms
Peak voltage, no load 77 V
Distortion etc.
THD 20 Hz–20 kHz and 1 W to full power 0.03 %
THD @ 1 kHZ and –1 dB under clip 0.006 %
DIM 30 at –3 dB under clip 0.008 %
Power 230 V version 115 V version
Operation voltage 130 V–265 V AC 65 V–135 V AC
Minimum start voltage 175 V 85 V AC
Full output power
at 4 ohms 180 V–265 V AC 90 V–130 V AC
Hum and Noise <–110 dB
Peak inrush current
(Soft start limited) 5 A 5 A
Channel separation @10kHz 70 dB
Current Draw @ 4ohms
Output impedance 30 mΩ
Quiescent power (no load) 0.9 Arms 1.8 Arms
1/8 of full power (–9 dB) 5 Arms 10 Arms
Slew Rate 40 V/s
1/3 of full power (–5 dB) 8 Arms 16 Arms
At full power (0 dB)
Inputs
@1 kHz 1% THD 14 Arms 28 Arms
Gain, selectable [dB] 20, 23, 26, 29, 32, 35, 38, 41
Impedance 20 kohm
Common mode rejection 50 dB
Net Dimensions
mm 483 (19˝) W ✕ 88 H ✕ 287 D
inch 19˝ W ✕ 3.5˝ H ✕ 11.3˝ D
Front Panel
Gain controls (2) channel A, B 31 positions detent
Clip Indicator (2) red LEDs
Output headroom
Shipping Dimensions
mm 560 W ✕ 180 H ✕ 500 D
inch 22˝ W ✕ 7.1˝ H ✕ 19.7˝D
indicators (10) green LEDs Fast peak – slow release
Temp Indicator (2) yellow LEDs 80°C at heatsink
Protect indicator (2) yellow LEDs >12 kHz at full power
or shorted output
Weight
Net 7.9 kg (17 lbs)
Shipping 9.6 kg (21.2 lbs)
On Indicator (2) green LEDs DC rail voltage for
channel A and B
Rear Panel
Input connectors (2) Neutrik Combo XLR type, 3 pin
and 1/4˝ jack
Link connectors (2) XLR type, 3 pin male
Output connectors (2) Neutrik 4-pole Speakon® connectors
Switches:
Clip limiter A and B On–Off (switchable)
Link-switch Ch. A–B
Approvals
CE:
Emission EN 55 103-1, E3
Immunity EN 55 103-2, E3, with S/N below 1% at normal operation level
Safety EN 60065, class I
ETL listed: Conforms to ANSI/UL STD 6500 and Certified to CAN/CSA E60065-00
FCC: Complies with Class B digital device, Part 15 of the FCC Rules.
NOTES:
1) Specifications measured with 230 V AC
2) Component tolerance dependent
3) Continuous power, one channel driven or peak power both channels driven
(Thermal protection may occur at high continuous power)
4) Normal operation level 1/8 of full power or –9 dB below clip level.
Lab.gruppen reserve the right to alter functions or the specification without prior
notice.
4)
Lab.gruppen AB, Gullregnsvägen 16, SE-434 44 Kungsbacka, Sweden.
Tel +46 300 56 28 00 Fax +46 300 56 28 99 e-mail: info@labgruppen.com www.labgruppen.com