Kyocera GRATINA 4G, KYF34 Settings Manual
Introduction
KYF34
Setting Guide
Thank you for buying the "GRATINA 4G" (simply called the "product"
from here on).
In this guide, settings and precautions for using the product are
described. For explanations of basic functions, refer to "Basic Manual".
Company names and product names referred to in this manual are
trademarks or registered trademarks of respective companies.
The TM, ® marks may be omitted in this manual. Screen illustrations
shown in this manual may look different from the actual screens. In
some cases, minor details or a part of a screen may be omitted.
First edition February 2017
■When Using the Product
Describes things to note when using the product.
■Basic Operation
Describes basic key operation.
■Using the Touch Pointer
Describes Touch Pointer operation.
■Preparing the Product for Use
Describes initial preparations.
■Initial Settings
Set an au ID etc. to use various services provided by au.
■Wi-Fi® Settings
Describes how to connect to a Wi-Fi® network.
■Checking On-Screen Status
Check the signal reception strength, battery level, etc. on-screen.
■E-mail
Make initial settings for @ezweb.ne.jp etc.
■How to Transfer Data with the Data Storage App
You can return/save data from your old au phone to the product
using a microSD memory card. You can also use an auスマート
パス (au Smart Pass) server to return/store phone book data to
the product.
■Reducing Battery Consumption
You can reduce battery consumption by enabling Eco Mode.
Soldby:KDDICORPORATION,
OKINAWACELLULARTELEPHONECOMPANY
Manufacturedby:KYOCERACorporation
Installing
Turn the power off and remove the battery pack
• See "Installing/Removing the Battery Pack" for how to
remove the battery pack.
Slide the au Nano IC Card (LTE) in the direction shown
in the slot cover
Note location of notch and direction of IC (metal) surface.
Notch
IC (metal) surface
Slide the au Nano IC Card (LTE) slot cover with the pad of
your finger in direction ① and then raise in direction ②
Be careful not to touch metal terminals on product when
raising cover. Do not slide cover forcefully (may damage
cover or injure hand/finger).
②
①
Lower the au Nano IC Card (LTE) slot cover in direction ①,
and then slide in direction ② with the pad of your finger
until it clicks locked
If cover is difficult to close, raise cover again and make sure
the au Nano IC Card (LTE) is installed all the way.
②
①
When Using the Product
Note the following when using the product.
● When you purchase the product, the battery is not fully charged. Be sure to charge the battery before use.
● To maintain water and dust resistance, attach the external connection terminal cover and back cover firmly.
Basic Operation
Basic key operations are described here. For detailed operation, refer to the "Basic Manual".
■ Key Names and Functions
Names of keys on the product and their functions are described.
①
③
④
⑤
⑥
⑦
⑧
⑨②
⑩
⑪
⑫
⑬
① k Center key
② u Phone book key
③ j Mail key
④ , Clear key
⑤ m Call/pair key
⑥ 0 – 9,-,
Number keys
⑦ q – z
Custom keys 1 – 3
⑧ d Cursor key
s
Left key/incoming history
f
Right key/outgoing history
e Up key
c Down key
^
⑨ o Camera key
⑩ l Browser key
Displays browser menu.
⑪ . Power/end call key
While using the product, end call
⑫ Touch area (Touch Pointer)
⑬
Using the Touch Pointer
Use your fingers in the touch area to operate in the same way as a touchpad (Touch Pointer).
Activate a Touch Pointer-capable function/application
" (OFF)/" " (ON) is displayed in the status bar, and " " (pointer) is displayed when the Touch Pointer is on.
"
● Hold down z for at least 1 second to toggle the Touch Pointer on/off.
● Key operation is still possible when the Touch Pointer is on (except some applications).
or exit functions. Hold down to
turn the power on or off.
v
Manner/shutter key
Removing
Turn the power off and remove the battery pack
• See "Installing/Removing the Battery Pack" for how to
remove the battery pack.
Slide the au Nano IC Card (LTE) in the direction shown
to remove
Slide the au Nano IC Card (LTE) slot cover with the pad of
your finger in direction ① and then raise in direction ②
Be careful not to touch metal terminals on product when
raising cover. Do not slide cover forcefully (may damage
cover or injure hand/finger).
②
①
Lower the au Nano IC Card (LTE) slot cover in direction ①,
and then slide in direction ② with the pad of your finger
until it clicks locked
②
①
■ Touch Pointer Operation
Tap/Double-tap Long-touch
Gently tap the touch area. To doubletap, tap the same position twice.
• By moving "
tapping, the item is confirmed
(okayed).
" above an item and
Slide Flick
While gently touching the touch area,
slide in the desired direction or to the
desired position. The pointer moves in
the slid direction.
• By long-touching the touch area, "
changes to "
scroll the screen.
• With the pointer at the edge of the
screen, slide toward off the screen to
scroll in the slid direction.
", and you can slide to
"
Zoom in/Zoom out
While touching the touch area with two
fingers, widen (zoom in) or close (zoom
out) your fingers.
Keep gently touching the touch area.
After tapping the touch area, the
indication returns to "
Flick your finger on the touch area up,
down, left, or right. The pointer moves in
the flicked direction.
• By long-touching the touch area, " "
changes to " ", and you can flick to
scroll the screen.
• With the pointer at the edge of the
screen, flick toward off the screen to
scroll in the flicked direction.
■ Installing/Removing the microSD Memory Card
You can save, move, and copy data by installing a microSD memory card (including microSDHC memory card) in the product.
● A protective card is preinstalled. If not using a microSD memory card, leave the protective card installed in the product to prevent parts
from rattling.
".
* The protective card can be used when a microSD memory card is uninstalled. Not installing the protective card does not adversely affect the
product.
● Turn off the power and remove the battery pack beforehand.
● A microSD memory card initialized on another device may not work on the product properly. Format the microSD memory card on this
product. Use the following steps.
When the standby screen is displayed, press k → [Settings] → [More settings] → [Storage] → [Erase SD card] → [Erase SD card] →
[Erase ever
● Make sure that the top/bottom and front/rear of the microSD memory card are facing correctly. Trying to force a wrongly oriented card
into the slot could make it impossible to remove the card or result in damage.
● Do not touch the terminal part of a microSD memory card.
ything]
Installing
Turn the power off and remove the battery pack
• See "Installing/Removing the Battery Pack" for how to
remove the battery pack.
Slide the microSD card slot cover with the pad of your
finger in direction ① and then raise in direction ②
Be careful not to touch metal terminals on product when
raising cover. Do not slide cover forcefully (may damage
cover or injure hand/finger).
②
①
Preparing the Product for Use
● Always turn the power off before installing or removing the battery pack, au Nano IC Card (LTE), or a microSD memory card.
● Attach the battery pack after checking that the au Nano IC Card (LTE) tray and microSD memory card are firmly in place.
● To maintain water resistance, firmly close the back cover without leaving any gaps.
● Attaching items improperly may result in damage to the battery pack or back cover.
■ Installing/Removing the Battery Pack
Installing
Remove the back cover of the back side of the product
Lift the back cover by the notch at its bottom (use fingernail,
etc.) in the direction shown to remove.
Notch
Attach the back cover
Place the back cover on the product and attach.
Install the battery pack
Confirm location of connection, and then slide battery pack in
and press firmly into place.
②
①
Connection
Battery pack
Press firmly making sure there are no gaps around the
back cover
Working your way all around the back cover in direction ①,
press firmly in direction ② to attach completely.
②
Slide the microSD memory card in the direction shown
in the slot cover
Note orientation of card.
Removing
Turn the power off and remove the battery pack
• See "Installing/Removing the Battery Pack" for how to
remove the battery pack.
Lower the microSD card slot cover in direction ①, and
then slide in direction ② with the pad of your finger until
it clicks locked
If cover is difficult to close, raise cover again and make sure
the microSD memory card is installed all the way.
②
①
Slide the microSD card slot cover with the pad of your
finger in direction ① and then raise in direction ②
Be careful not to touch metal terminals on product when
raising cover. Do not slide cover forcefully (may damage
cover or injure hand/finger).
②
①
①
Removing
Remove the back cover of the back side of the product
Lift the back cover by the notch at its bottom (use fingernail,
etc.) in the direction shown to remove.
Notch
Remove the battery pack
Lift the battery pack by the notch (using fingernail, etc.) in the
direction shown to remove.
Notch
Battery pack
■ Installing/Removing the au Nano IC Card (LTE)
The au Nano IC Card (LTE) contains customer phone number and other information. The product is compatible with au Nano IC Card (LTE)
only. You cannot use the product with an IC card other than au Nano IC Card (LTE).
● When handling the au Nano IC Card (LTE), observe the following to avoid malfunction and
au Nano IC Card (LTE)
Back Front
IC (metal) part
● Turn the power off beforehand and remove the battery pack.
● When the au Nano IC Card (LTE) is not inserted
If the au Nano IC Card (LTE) is not inserted, the following operations are unavailable. "
• Making*/Receiving a call
• Sending/Receiving SMS
• Making initial e-mail settings and sending/receiving e-mail
• Making PIN code settings
• Checking product phone number and e-mail address
Besides the above, functions which require your phone number etc. may not be available.
* Emergency calls also cannot be made to 110 (police), 119 (fire department), or 118 (coast guard). However, calls can be made if signal strength
during GSM/UMTS roaming is any level other than "Out of service area" (emergency numbers depend on the country; calls may not connect).
● Restricting product use with a PIN code
Your au Nano IC Card (LTE) contains valuable personal information. To protect this information, you can change the PIN code and lock
the SIM card to restrict use by other persons.
damage.
• Do not touch the IC (metal) part on the au Nano IC Card (LTE) or the IC card terminals on the
product.
• Confirm the correct orientation for installing.
• Do not forcefully install or remove.
● An error message is displayed if the au Nano IC Card (LTE) is not installed correctly or if it has
an abnormality.
● Be careful not to lose the removed au Nano IC Card (LTE).
● Do not insert the au Nano IC Card (LTE) if in a card adapter. May cause malfunction.
" is also displayed.
Slide the microSD memory card in the direction shown
to remove
Lower the microSD card slot cover in direction ①, and
then slide in direction ② with the pad of your finger until
it clicks locked
②
①
■ Charging
● While charging, the charging/notification indicator illuminates in red. When charging is finished, the charging/notification indicator goes
out.
● The product may become warm while charging, depending on the situation, but this is not abnormal.
● When you operate the product with the specified charger (sold separately) connected, the product may repeat short-time charging/
discharging resulting in short battery life.
● When temperature of environment or the product becomes extremely high or low, charging may be stopped. Try to charge the battery
as far as possible at room temperature.
● If the charging/notification indicator blinks in red, check if the phone is connected correctly, etc. Even if the indicator keeps blinking,
stop charging and then contact an au shop or Repair and Delivery Service Center.
Charging with a Specified AC Adapter (Sold Separately)
Open the external connection terminal cover of the
product
Insert the power plug of Common AC Adapter 05 (sold
separately) into an outlet (100 VAC to 240 VAC)
Check the orientation of the microUSB plug of Common
AC Adapter 05 (sold separately) and insert it straight into
the external connection terminal
With the projections
facing down
Common AC Adapter 05
(sold separately)
Charging/
notification indicator
Common AC Adapter 05
(sold separately)
Charging with a desktop holder (KYF31PUA) (sold separately) and Common AC Adapter 05 (sold separately)
Insert the microUSB plug of Common AC Adapter 05
(sold separately) to the connection jack of the desktop
holder (KYF31PUA) (sold separately)
Check the orientation of the microUSB plug and insert in
the direction shown.
Connection jack
Insert the power plug of Common AC Adapter 05 (sold
separately) into an outlet (100 VAC to 240 VAC)
■ Changing E-mail Address
With the projections
facing down
Mount the product in the desktop holder (KYF31PUA)
(sold separately)
Charging/notification indicator
Common AC Adapter 05
(sold separately)
①
Common AC Adapter 05 (sold separately)
②
Charging with a PC
If you use the microUSB cable to charge the battery, it may take the battery longer to be fully charged than if you use the specified AC
adapter (sold separately).
Open the external connection terminal cover of the
product
Connect the microUSB cable 01 (sold separately) to a
USB port of a PC after the PC is activated completely
USB port of a PC microUSB cable 01
(sold separately)
When the standby screen is
displayed, press
Enter the security code
→ [送信 (Send)]*
* The security code is the 4-digit number set at subscription.
j
u
(Menu) → [E-mail settings]
Confirm the contents
→ [承諾する (Accept)]
[Other settings]
Enter an e-mail address
→ [送信 (Send)]
Confirm the contents
→ [接続する (Connect)]
→ [Eメールアドレスの変更へ
(To change e-mail address)]
[OK] → [閉じる (Close)]
■ Backing Up E-mail
You can back up e-mail.
● If a microSD memory card is inserted into the product, e-mails are saved on the card. If not, they are saved to the internal memory.
Check the orientation of the microUSB plug of
microUSB cable 01 (sold separately) and insert it
straight into the external connection terminal
• If a screen for detecting new hardware, etc. is displayed
on the PC, select "Cancel".
Charging/notification indicator
With the projections
facing down
microUSB cable 01 (sold separately)
■ Turning the Power On/Off
Turning the Power On Turning the Power Off
When the standby screen is
displayed, press
j
u
(Menu) →
[E-mail settings]
[Backup/Restore] →
[Mail Backup] → [OK]
Select the character code
→ [OK] → Select folders to
back up → [OK]
How to Transfer Data with the Data Storage App
You can return/save data from your old au phone to the product using a microSD memory card or an au server.
● To return data using an au server, store the data from the old au phone to the au server beforehand. Setting au ID is required for using
the au server.
● To return data using a microSD memory card, save the data from the old au phone to the microSD memory card beforehand.
When the standby screen is
displayed, press k
→ [Security/Safety]
[Data Storage App]
* If an update is required, a
confirmation screen is
displayed. Follow the on-screen
instructions.
[データ移行 (Data transfer)]
■ Returning Data with the Data Storage App
If you selected
"SDカードから復元する
(Restore from SD card)"
If you selected
"auサーバーから戻す
(Return from au server)"
Press and hold . for at least
2 seconds
Press and hold . for at least
1 second
[Yes]
Initial Settings
The first time the power is turned on, a screen for making initial settings is displayed, and you can set an au ID.
An au ID is an identifier for customers using au services. Register your au phone number as an au ID. By setting an au ID, you can use
various services provided by au such as au スマートパス (au Smart Pass), My au, and au WALLET.
Switch to English Display
• See "Switching to English
Display" for how to switch
to English display.
.
When the standby screen is
displayed, press k →
[Settings] → [au ID Setting]
Confirm the contents → [OK]
Continue by following the
on-screen instructions.
To exit setting, . → [Yes].
Select the method
for returning data
* To return data with "auサーバー
から戻す (Return from au
server)" (data stored on an au
server), you must set an au ID.
If you selected "SDカードから
復元する (Restore from SD
card)", select the type of data
* Not displayed if you selected
"auサーバーから戻す (Return
from au server)" at step 4.
■ Saving Data with the Data Storage App
If you selected
"SDカードに保存する
(Save to SD card)"
Select the data to return
→ o (次へ (Next))
→ o (完了 (Done))
* This screen is displayed if you
selected "アドレス帳や写真など
を戻す (Return phone book,
photos, etc.)".
If you selected
"auサーバーに預ける (Store on
au server)"
Select the data to return
→ o (次へ (Next))
→ o (完了 (Done))
Confirm the contents → [同意
して次へ (Agree and Next)]
* The security code is the 4-digit number set at subscription.
Enter the security code
→ [次へ (Next)]*
au ID setting is complete
■ Switching to English Display
You can switch the display from Japanese to English.
When the standby screen is displayed, press k → [設定 (Settings)] → [その他の設定 (More settings)] → [言語と入力 (Language &
input)] → [言語 (Language)] → [English] → [はい (Yes)]
Wi-Fi® Settings
You can use a household wireless LAN (Wi-Fi®) environment or a public wireless LAN environment when outside to connect to the Internet.
* The battery is consumed faster when the wireless LAN (Wi-Fi®) function is on. You should set the wireless LAN (Wi-Fi®) function off when not in use.
A list of available Wi-Fi® networks
is displayed. To connect to a
Wi-Fi® network, select the Wi-Fi®
network → k → enter password if
required → o (Connect).
If the Wi-Fi® network you want to
connect to is not detected, press
u
(Menu) → [Add network] and
connect to the Wi-Fi® network
manually.
When the standby screen is
displayed, press k
→ [Settings]
[Wireless/Network]
→ [Wi-Fi]
Select "Wi-Fi" and set to
Select where to save the data
* To save data with "auサーバーに
預ける (Store on au server)"
(store data on an au server),
you must set an au ID.
■ Setting Auto-Saving
When the standby screen is
displayed, press k
→ [Security/Safety]
If you selected "SDカードへ
データを保存する/戻す
(Save/return data to SD card)"
Select the data to save
→ o (次へ (Next))
→ o (完了 (Done))
[Data Storage App] [SDカードへデータを
Select the data to save
→ o (次へ (Next))
→ o (完了 (Done))
保存する/戻す (Save/Return
data to SD card)]/[auサーバー
に預ける/戻す (Store/Return to
au server)]
* If you selected "auサーバーに預
ける/戻す (Store/Return to au
server)", you must set an au ID.
If you selected "auサーバーに
預ける/戻す (Store/Return on
au server)"
Checking On-Screen Status
Check the signal strength and battery level on-screen.
① Signal strength (received field strength)
– :Level display :Out of service area
• The icon indicating network is displayed at the upper left.
:4G (LTE) available
:3G available
:Roaming
② Battery level
:100%/ :empty/ :charging
E-mail
To use e-mail (@ezweb.ne.jp), subscription to LTE NET is required.
If you did not subscribe when you purchased the product, contact an au shop or Customer Service Center.
Your e-mail address is determined automatically after initial setting. You can change the e-mail address later.
■ Initial Settings
[SDカードへの自動保存設定
(Auto-save to SD card
settings)]
Select "保存する (Save)" → k
(ON) → Set "保存データ種別
(Saved data type)" and "自動開
始日付 (Auto start date)"
Select "アドレス帳の自動お預
かり設定 (Phone book
auto-store settings)"
→ k (ON)
Check "アドレス帳を預ける
(Store phone book)"
Viewing/Playing data
You can view/play data on the product by the following operations.
When the standby screen is displayed, press k → [Data Folder] → Select the folder → k → Select the data to display →
Reducing Battery Consumption
You can reduce battery consumption by enabling Eco Mode.
● Some applications may not function properly when Eco Mode is enabled.
k
When the standby screen is
displayed, press
j
Confirm the contents
→ [接続する (Connect)]
Confirm the contents
→ [閉じる (Close)]
When the standby screen is
displayed, press k → [Tool]
[Eco Mode] [ON]/
[AutoON (BatteryLevel)]/
[AutoON (TimeZone)]
Loading...