本製品 6277 シリーズコネクタは、0.5 mm ピッチワンタッチロックタイプの FPC 用コネクタです。
本コネクタの取り扱いには注意が必要です。ここで 6277 シリーズコネクタの取り扱い上の注意点について
記載します。
Series 6277 FPC connector is a 0.5 mm pitch, one touch lock type connector.
This connector requires your attention to the following points in its handling.
This manual shows notes in handling Series 6277.
2222....各部
各部のののの名称
各部各部
名称 NAME OF EACH PART
名称名称
NAME OF EACH PART
NAME OF EACH PARTNAME OF EACH PART
<スライダー嵌合状態>
インシュレ
INSULATOR
<スライダー開放状態>
スライダー
SLIDER
ータ
保持金具
ANCHOR PLATE
コンタクト
CONTACT
SERIES 6277
6277 INSTRUCTION MANUAL SPEC No.205-03-208
62776277
106-03-004 PAGE 2/6
Page 4
KYOCERA ELCO CORPORATION
3
3....取取取取りりりり扱扱扱扱いいいい上上上上のののの注意
3 3
3.1 基板搭載について MOUNTING ON THE BOARD
基板搭載は基本的には実装機にて行ってください。補修などで手のせをする場合は、コンタクトテール
に触れない様注意して下さい。
Basically connectors shall be mounted by the mounting machine. In case of the manual mounting,
do not to touch contact tails.
3.2 FPC の挿入方法について INSERTION AND EXTRACTION OF FPC
FPC 挿入方法 FPC INSERTION
(1) スライダーは解除状態で上方 90°開きます。完全に開いていないと FPC 挿入性に支障が
The slider opens up to 90 degrees when unlocked. Open the slider completely,
or the FPC will not be insered correctly.
注意 HANDLING NOTES
注意注意
ありますので注意してください。
HANDLING NOTES
HANDLING NOTESHANDLING NOTES
90°
※スライダーを開放する際、下図のスライダーの真ん中を左右均等に荷重が掛かった状態で真上に上げ
る様に操作してください。片側に荷重を掛けた状態で開放しないよう注意願います。
When opening the slider, push the center of the slider directly upward with the slider evenly loaded,
on it’s right and left around the center,do not apply uneven load on the slider when opening it.
SERIES 6277
6277 INSTRUCTION MANUAL SPEC No.205-03-208
62776277
106-03-004 PAGE 3/6
Page 5
KYOCERA ELCO CORPORATION
※スライダーは開放角度は90°とし、さらに開く方向へは 0.1 kgf 以上の荷重を加えないようにしてください。
Slider opening angle must be 90 degrees MAX.
When it needs to open more than 90 degrees, load should be 0.1 kgf MAX.
(2)FPC は、コネクタのカードスロットに突き当たるまでしっかりと挿入して下さい。
また本製品は仮保持機構を有している為、FPC 挿入時には抵抗が有ります。
Insert the FPC and push it until it hits the card slot of connector.
As the connector has the temporary retaining system, some stress is felt when in serting the FPC.
SERIES 6277
6277 INSTRUCTION MANUAL SPEC No.205-03-208
62776277
正常挿入
Proper insertion
斜め挿入
oblique insertion
挿入不足
Insufficient insertion
106-03-004 PAGE 4/6
Page 6
KYOCERA ELCO CORPORATION
(3)スライダーをロックさせて下さい。挿入した FPC が斜めになっていないか確認した上、
スライダーを回転軸方向に軽く荷重を加えつつ押し下げ、ロックさせてください。
Make sure that the FPC is not inserted obliquenly and press the slider down for locking with
soft pressure applied on it in the direction of the rotation axis.
3.3 FPC の抜去方法 FPC EXTRACTION
スライダーを下図のようにあげて、ロックを解除させて下さい。
Lift the slider as shown below to unlock.
3.4 FPC の屈曲について FLEXION OF FPC
FPC の屈曲によりコネクタ接点部に過剰な負荷がかからないようにご注意願います。
ては弊社にて評価確認を行います。
Pay attention not to apply an excess load to the connector contacts.
because of the flexion of FPC. Please contact us when an FPC has to be bent repeatedly near the
card insertion opening. We will conduct evaluation tests according to conditions.
可能な限り長くしてください
As loon as possible
SERIES 6277
6277 INSTRUCTION MANUAL SPEC No.205-03-208
62776277
106-03-004 PAGE 5/6
Page 7
KYOCERA ELCO CORPORATION
4444....その
その他他他他のののの注意事項
そのその
納入時は、エンボステープ仕様でコンタクトテール及び金具は保護されていますが、投げたり、
大きな衝撃を加えないように注意して下さい。
Throwing and large shock shall not be permitted. However,though contact tails and anchor plate
are protected in the embossed tape when delivered.