Chapter 5:Remote Control ..............................................................................................................................9
Note: For multi language installation manual, please install Adobe Acr obat Reader from autorun after
inserting the CD into the CD ROM. Click “Browse” and open Installation Manual file where multilanguage installation manuals are in.
1
Page 2
Chapter 1 : PlusTV PCI Express TV Card Hardware Installation
1.1 Package Contents
Unpack your PlusTV PCI Express TV Card package and make sure that all items are intact. The following
items should be included in your package:
z PlusTV PCI Express TV Card
z Installation CD and CyberLink PowerDirector5
z Quick Start Guide
z DVB-T Antenna(Optional)
z FM Antenna
z Remote Control and sensor
z External Multi-cable
z Power-up Cable
z Internal AV input Kit
z Adaptor Connector
1.2 System Requirements
z PC with Pentium-IV 2.0GHz or above (Recommend:2.8 GHz)
z 512MB RAM of system memory or above ((Recommend: 1GB)
z 1 available PCIe compliant slot
z Graphics TV Card (Must support DirectX 9.0C)
z Sound TV Card (AC97 compatible sound TV Card)
z 2GB free HD space
z CD-ROM drive (For software installation)
z Microsoft Windows® XP(SP2) / XP MCE / Windows Vista
2
Page 3
1.3 Hardware Installation
Please follow the steps & connection chart shown below for installation of your TV Card and follow the
pictorial guide below for peripheral connections.
1. Warning: Installation Hazard , Please exercise precaution when installing your TV tuner card!
A. Shut down your computer.
B. Unplug the main computer.
C. Press the power button for 3 seconds. (To ensure your computer is completely powered-off.)
D. Open the cover of your main computer.
2. Please choose an available socket for your product and connect your TV tuner card with the motherboard.
3. Please remove the Power SW pin (CON1) of your PC from the motherboard, connect it with the Power
Switch cable (CON2), plug CON3 on the Power Switch cable to the Power Pin on the motherboard, and
plug CON4 on the Power Switch cable to the connector on your TV tuner card.
4. Please place the “Internal AV Input Kit” in a PCI or PCI Express Card Slot and connect CON5 to the
connector on your TV tuner card.
5. Please put your PC case back together and reboot your computer.
6. When you reboot your computer, for all system newer than Windows XP will automatically detect the new
hardware and launch “Found New Hardware Wizard”: when this happens please click on the “cancel”
button.
3
Page 4
Chapter 2 : PlusTV PCI Express Quick Installation
The PlusTV PCI Express TV Card package comes with complete Windows software utilities. These utilities
can be found on the CD-ROM in this package. During installation, it is highly recommended to disable any
sub-programs. These include applications such as antivirus software and system monitoring applications.
1. When you finish the hardware setup and restart your
system. The “Found New Har dware Wizard” window
will pop up. Please click “Cancel” and you can make
use of PlusTV PCI Express Quick Installation for proper
installation.
2. Insert the installation CD into the CD ROM device. The
autorun page will appear as the left image. Please choose
“Quick Installation”.
Note: If you already installed old version Applications,
Please refer to Chapter 4 FAQ-4. Naturally you can skip the
step.
3. Please read the End User License and then click “Next”
to continue.
4
Page 5
4. The Quick Installation provides you with two choices to
install. Please choose “Typical Installation” for
complete device driver and software installation, or
choose “ Custom Installation” to set up options
according to your personal needs. Click “Install ” to
continue.
5. Now the driver has been installed successfully on your
computer and click “OK” to finish driver installation and go
to next step.
6. Now the Quick Installation Complete. Please choose
“Yes, I want to restart my computer now” to restart
your computer (Recommend) and click “Finish” to end
the installation.
5
Page 6
Chapter 3:PlusTV PCI Express Quick Uninstallation
1. If you want to uninstall device driver and software utility,
please click “Quick Uninstallation”.
Note: You can also take another way to uninstall device
driver and software utility, please refer to chapter 4 FAQ 3.
2. The Quick Uninstallation provides you with two choices
to uninstall. If you want to uninstall device driver and
software utility completely, please choose “Typical Uninstallation”. or if you want to uninstall them partially,
Please choose “ Custom Uninstallation”. Finally click
“Uninstall” to continue.
3. Now the Quick Uninstallation Complete. Please choose
“Yes, I want to restart my computer now” to restart
your computer (Recommend) and click “Finish” to end
the installation. Please wait, while the uninstallation is in
process.
6
Page 7
Chapter 4 : FAQ
4.1 How to check if the driver has been installed successfully or not?
Ans :Right click on “My Computer” on the desktop and choose “Properties”. Once in “Properties”
window, click on “Device Manager” in Hardware panel. Click on the plus icon of “Sound, video and
game controllers” to open the device list. See Fig. 1 below.
Fig. 1
4.2 How to check if the Remote Control can work fine?
Ans : 1) You have to check if the “Remote Control” utility is installed or not. Please refer to Fig. 2.
2) You have to check if the driver has been installed or not.
3) You can check if the “Remote Control” tray icon is loaded in the right-bottom of task bar.
See Fig.3. below.
Fig. 2 Fig.3
4.3 How to uninstall all of device driver and software utility?
Ans:1) You can put the installation CD into CD-ROM device to execute “Quick Uninstallation”.
2) You can also follow the step (StartÆProgramsÆKWorld MultimediaÆUninstallation ) to
Uninstall. Please refer to Fig.4
Fig.4
7
Page 8
4.4 Why the inputted video stops and HyperMediaCenter makes no response ?
Ans:This problem might occur when the video inputted from “Component”(on Internal AV input Kit ). The reason is Graphic card ram doesn’t real-time process data. PLS close HyperMediaCenter and run
HyperMediaCenter again.
4.5 Remove old Version Applications.
Ans : The Install Wizard will detect Applications version automatically. If you already installed an old
Version, it will pop-up a warning window. Please click “Yes” to uninstall old version applications.
Otherwise click “No” to reverse current version Application and install new driver. Please refer to
Fig.5
Fig.5
4.6 LiveUpdate Icon ?
Ans : Double click on “LiveUpdate” icon, then Please follow the on-screen instructions to update the latest
Driver/AP via internet.
8
Page 9
Chapter 5:Remote Control
Button Function
Turn on / off HyperMedia Center
Shut down the PC
Video Source switch (Antenna, Cable, Memory,
Composite, S-Video)
Audio switch (Stereo, SAP or MONO)
Number keys (0~9)
Recall
Mute
1. Minimize
2. Switch screen 1 to screen 2. (Only for Dual TV
product)
Switch between full screen and window mode
Return to main page
Return to last page
Arrow keys
Enter
Volume up / down
Channel up / down
Time-Shifting
Record
Playback
EPG (Electronic Program Guide for Digital TV)
Teletext(For Digital TV)
Adjust screen ratio between 4:3 / 16:9 / 16:10
SnapShot
Sleep Timer
Adjustment