Kuhn Rikon 5085, 5073, 50100 User Manual

TRAILER PARTS MANUAL

VERTICAL MIXER

MODELS 5073, 5085 and 50100

Abbreviations ................................................................................................. 2

Using This Service Parts Listing .................................................................... 3

Body Parts ..................................................................................................... 4

Light Kit.......................................................................................................... 5

Wheel and Hub Parts - 5073 ......................................................................... 6

Undercarriage Parts ...................................................................................... 7

Input Shaft and Pinion Gear Drive Parts ...................................................... 10

Gearbox ....................................................................................................... 11

Auger Drive and Tower Assembly Parts ...................................................... 12

Auger Assembly Parts ................................................................................. 16

Door and Cylinder Parts .............................................................................. 25

Door and Cylinder Parts 5073-068 and Before............................................ 26

Slide Tray Parts ........................................................................................... 27

4 Auger Discharge Parts .............................................................................. 28

Chain and Slat Discharge Parts .................................................................. 30

High-Speed Clean-Out Option ..................................................................... 32

High-Speed Clean-Out Option - Gearcase Replacement Parts................... 34

Selector Valve Option .................................................................................. 35

PTO Driveline (1000 RPM - 21 - Spline -1 3/8 Yoke) After S/N 5073-066.... 36

PTO Driveline (1000 RPM - 21 -Spline-1 3/8 Yoke) Before S/N 5073-065 .. 37

Side Extension Options ............................................................................... 39

Decal and Paint List ..................................................................................... 40

Hardware Part Number Listing .................................................................... 41

Catalog Part Number 005907 Unit Serial Number_____________

Operator Instruction Manual for this unit: 005893

5073TR 005907 R060706

Abbreviations

Assy ................................................ Assembly

A/R ..............................................As Required

B ............................................................... Bolt

Brg ...................................................... Bearing

BSN .............................. Before Serial Number

Btm ...................................................... Bottom

C-Bolt ........................................ Carriage Bolt

Cttr ........................................................ Cotter

CV ....................................... Constant Velocity

Deg..................................................... Degree

Dia .................................................... Diameter

ea ........................................................... Each

eq or Equiv .....................................Equivalent

Fln ...................................... Flanged Lock Nut

Fw ............................................... Flat Washer

Ga ....................................................... Gauge

Gr or Grd .............................................. Grade

Hd ........................................................... Head

Hfw ................................... Heavy Flat Washer

Hyd .................................................. Hydraulic

ID ........................................... Inside Diameter

Ill or Illus ......................................... Illustration

Ind .....................................................Indicator

Jn ...................................................... Jam Nut

Kw ...................................................... Keyway

LH .................................................... Left Hand

Ln ..................................................... Lock Nut

Lw .............................................. Lock Washer

Mtg Hrd ........................... Mounting Hardware

NC .........................................National Coarse

NF ............................................. National Fine

NLA ................................ No Longer Available

NPT ...............................National Pipe Thread

OD ...................................... Outside Diameter

Pc(s) .................................................. Piece(s)

PD ........................................... Pitch Diameter

PHB .......................................... Pan head bolt

PTO ............................... Power Takeoff (shaft)

Qty ..................................................... Quantity

RH ................................................ Right Hand

SN ........................................... Serial Number

SHCS ...................... Socket Head Cap Screw

Spk, or Spkt or Sprkt ......................... Sprocket

Sq ........................................................ Square

SS ........................................... Stainless Steel

SSB .................................. Stainless Steel Bolt

St ........................................................ Straight

Std .................................................... Standard

STS .................................. Self Tapping Screw

UASN .....................Used After Serial Number

UBSN ................. Used Before Serial Number

W ............................................................. With

W/O .................................................. With Out

Using This Service Parts Listing

This listing uses a number indentation system to specify the parts of an assembly. Any number which is indented to the right, indicates that it is a component of the item to the upper left. Example:

Part no Qty Description 102-AAA # Assembly A

102-BBB # Sub-Assembly B (Component of A)

140-xxx # Sub-Component of B

140-xxx # Sub-Component of B 102-CCC # Sub-Assembly C (Component of A)

etc.

5073TR 005907 R060706

The serial number may consist of a number, or a number with a letter prefix. When referring to serial number breaks in the text of this manual, a serial number with a prefix will have been manufactured after a serial number without a prefix (A001 made after 0123). Likewise, a higher prefix letter would indicate manufacture after a lower prefix letter (B001 made after A123). Therefore, if the text refers to units manufactured after serial number B123, this would include “B” series numbers greater than 123, and all numbers with a higher letter prefix.

If you cannot find the part you need, be as descriptive as possible when placing an order:

Using this system, the subassemblies and their components are included if an Assembly is ordered. Similarly, the components of a subassemblies are included if a subassembly is ordered.

The quantity (Qty) associated with an assembly, represents the number of times an assembly could be shown in the drawing. The subassembly quantity however, is the number of times a subassembly is used to build one assembly. Similarly, the component quantity refers to the number of times a given component is found in one subassembly.

MODEL AND SERIAL NUMBER INFORMATION is located near the front left hand corner (Fig. A). The model number, serial number and part number should be known when asking service personnel for parts.

Sprockets: give the bore size, number of teeth, and size of keyway. Roller chain: give the size of chain (stamped on the side of each link) and number of links. Shafting: give the diameter, length, and quantity and size of keyways.

Hardware is generally not included with parts. If you need any hardware, check the size, the length, and the grade (Fig. B), then check the hardware list in this manual for the part numbers.

All hex head bolts are grade 5, and nuts are grade 5 unless otherwise stated.

The hardware listing also includes zerks, cotter pins, set screws, and roller chain links.

The illustrations in this manual are meant to be used only as a guide for identifying parts and locating their relative positions.

Figure A

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Body Parts

REF PART NO QTY DESCRIPTION

1 103-678 2 Haydog; Mtg. Hrd: 1/2” x 1 3/4”B, LN (1EA) 2 174-765 2 Bent Hitch Pin, 1/2” DIA x 2 1/2” 3 102-437 1 Swing Arm, Outer; Mtg. Hrd: 1/2” x 1 1/2” B, LN,Includes T-bolt 4 136-454 1 Spacer Pad” 5 102-439 1 Swing Arm, Inner 6 141-301 1 Shield, Drive; Mtg Hrd: 5/16” x 1”B, Belleville Washer,LN(2EA) (5073 ONLY)

141-366 1 Shield, Drive - Front; Mtg Hrd: 3/8” x 1”B, Belleville Washer,LN(2EA) (5085 & 50100 ONLY)

144-462 1 Shield, Drive - Rear (5085 & 50100 ONLY) 7 103-674 1 Clevis Mount; Mtg. Hrd: 3/4” x 4 1/2” GRD-8 B,LN (5073 ONLY) 8 140-611 2 Clevis, Retainer (5073 ONLY) 9 103-779 1 Clevis; Mtg. Hrd: 3/4” x 2”B, LN (4EA) 10 141-547 1 Dipstick 11 174-839 1 Jack Mount Tube(Weld On) 12 171-919 1 Drain Plug 13 141-297 1 Fender, RH (weld-on) (5073 ONLY)

141-302 1 Fender, LH (weld-on) (5073 ONLY)

141-370 2 Fender, dual axle (5085 & 50100 ONLY)

Mtg Hrd: 5/16” x 1-1/4” Bolt, FW, LW, and Nut, (8ea) 3/8” Heavy Washer (8ea)

14 174-763 1 Weigh Bar, Hitch, 2-1/2”; Mtg; Hrd: 3/4’ x 4 1/2” GRD8 B, LN

Body Parts

REF PART NO QTY DESCRIPTION

1 174-676 1 Jack, Sidewind 10,000lb 2 174-838 1 Jack Mount Pin (includes “R” clip) 3 174-840 1 Crank Assembly 4 174-839 1 Jack Mount Tube (weld on)

5073TR 005907 R060706

Light Kit

REF PART NO QTY DESCRIPTION

1 174-675 1 Light Kit 2 174-673 2 Light, Amber

174-674 2 Light, Red 3 174-725 4 Grommet 4 174-775 1 Wire Harness 5 174-724 4 Light Connector (pigtail only) 6 172-110 1 7 Pin Connector (SAE J560B)

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Wheel and Hub Parts - 5073

REF PART NO QTY DESCRIPTION

1 174-755 1 Grease Seal; Transcom #37605SA 2 173-001 1 Bearing Cone; HM218248 3 172-999 1 Hub, Wheel 10 Hole 4 173-031 1 Bearing Race; HM218210 5 174-784 10 Stud, Wheel, 3/4” NF 6 170-920 10 Lug Nut; 3/4” NF 7 173-032 1 Bearing Race; HM212011 8 173-002 1 Bearing Cone; HM212049 9 174-757 1 Washer Spindle 2 1/16” x 4” 10 174-756 1 Nut; Castle 11 173-007 1 Cover; Mtg. Hrd: 5/16” x 3/4”B, LW (4EA) 12 174-804 1 Roll Pin, 3/8” x 3” 13 170-023 1 Grease Fitting 1/4”

14 173-008 2 Wheel and Tire Assy (Aircraft) 15 173-170 1 Wheel Rim (inner); Mtg. Hrd: 1/2” x 1 1/4” B, LN (32EA) 16 173-171 1 Wheel Rim (outer) 17 173-172 1 Tire 44 1/2” x 16 1/2” 18 173-173 1 Inner Tube 44 1/2” x 16 1/2“ (not shown) 19 173-174 1 Flap, 44 1/2” x 16 1/2“ (not shown)

14 175-331 2 Wheel and Tire Assy 46 x 18 - 20, (neg 2” offset) (Aircraft) 15 175-334 1 Wheel Rim (inner); Mtg. Hrd: 1/2” x 1 1/4” B, LN (32EA) 16 175-333 1 Wheel Rim (outer) 17 175-332 1 Tire, 46” X 18” Aircraft 30 ply 18 175-335 1 Inner Tube 46 x 18 - 20 (not shown) 19 175-336 1 Flap, 46 x 18 - 20 (not shown)

20 174-759 2 Weigh Bar, Spindle, 3-3/4”; Mtg; Hrd: 5/8” x 5 1/2” B, LN

5073TR 005907 R060706

Undercarriage Parts - 5085 and 50100 (S/N 5085-B0001, 50100 C0001 and after)

1064

17 18 19

REF PART NO QTY DESCRIPTION

104-646 1 Undercarriage with Bogies 1 104-559 1 Undercarriage Weldment 2 103-844 1 Tie Rod Assembly 3 103-910 1 RH Bogie Assembly with Hubs

103-911 1 LH Bogie Assembly with Hubs

4 103-908 1 RH Bogie Weldment (170-865) 1/8” NPT Grease Zerk

103-909 1 LH Bogie Weldment (170-865) 1/8” NPT Grease Zerk 5 141-569 2 Spindle, 4 1/2” x 18” (Weld On) 6 141-967 1 Spacer (Weld On) 7 141-574 1 Bushing, Bogie Pivot 8 173-006 2 Grease Seal 9 173-001 2 Inside Bearing Cone; HM218248 10 172-999 2 10-Bolt Hub 11 173-031 1 Inside Bearing Race; HM218210 12 174-784 10 Wheel Stud, 3/4” 13 170-023 1 Grease Zerk 14 170-920 10 Wheel Nut, 3/4” 15 173-032 1 Outside Bearing Race; HM212011 16 173-002 2 Outside Bearing Cone; HM212049 17 173-003 2 Spindle Nut, Inner; DANA# M10HM101 18 173-004 2 Lock Washer; DANA# M10HM100 19 173-005 2 Spindle Nut, Outer; DANA# M10HN102 20 173-007 2 Dust Cap Mtg Hrd: 5/16” x 3/4” Bolt (Qty 6)

21 175-174 4 Wheel, 22.5 x 13 22 171-653 4 Tire, 22.5 385-65R 23 174-577 4 Tube, 15R/16.5 (Not Shown)

21 175-177 4 Wheel, 22.5 x 11.75 22 175-178 4 Tire, 22.5 315/80R 23 174-577 4 Tube, 15R/16.5 (Not Shown)

24 174-979 4 Weigh Bar; 2.875” 25 103-845 4 Weigh Bar Mount

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Undercarriage Parts - 5085 and 50100 (After S/N 5085-054, 50100-069, Before S/N 5085-B0001, 50100 C0001)

REF PART NO QTY DESCRIPTION

1 103-906 1 Undercarriage with Bogies 2 103-779 1 Clevis; Mtg Hrd: 3/4” x 4 1/2” GRD-8 B, LN 3 103-844 1 Tie Rod Assembly Mtg Hrd: 3/4” Nut, Jam Nut, (170-236) Cotter Pin (1 ea) & FW (2) 4 141-574 1 Bushing, Bogie Pivot 5 103-911 1 LH Bogie Assembly

103-910 1 RH Bogie Assembly

6 103-909 1 LH Bogie Weldment (170-865) 1/8” NPT Grease Zerk

103-908 1 RH Bogie Weldment (170-865) 1/8” NPT Grease Zerk 7 141-967 1 Spacer (Welds to the bogie axle receptical) 8 141-569 2 Spindle, 4 1/2” x 18” 9 172-999 2 10-Bolt Hub 10 173-031 1 Inside Bearing Race; HM218210 11 174-784 10 Wheel Stud, 3/4” 12 170-920 10 Wheel Nut, 3/4” 13 173-032 1 Outside Bearing Race; HM212011 14 173-002 2 Outside Bearing Cone; HM212049 15 173-003 2 Spindle Nut, Inner; DANA# M10HM101 16 173-004 2 Lock Washer; DANA# M10HM100 17 173-005 2 Spindle Nut, Outer; DANA# M10HN102 18 173-007 2 Dust Cap; Mtg Hrd: 5/16” x 3/4” Bolt (Qty 6) 19 173-006 2 Grease Seal 20 173-001 2 Inside Bearing Cone; HM218248 21 175-174 4 Wheel, 22.5 x 13.5 10 Hole, 1.5 Neg Offset 22 171-653 4 Tire, 385-65R Truck Recap w/ Rib Hwy Tread 23 174-577 4 Tube, Tire (not shown) 24 174-979 4 Weigh Bar; 2.875”

5073TR 005907 R060706

Undercarriage Parts - 5085 and 50100 (Before S/N 5085-055, 50100-070*)

REF PART NO QTY DESCRIPTION

1 103-906 1 Undercarriage with Bogies 2 103-779 1 Clevis; Mtg Hrd: 3/4” x 4 1/2” GRD-8 B, LN 3 103-844 1 Tie Rod Assembly Mtg Hrd: 3/4” Nut, Jam Nut (170-236) Cotter Pin (1 ea) & FW (2) 4 134-843 1 Bushing, Bogie Pivot 5 102-049* 1 LH Bogie Assembly

102-048* 1 RH Bogie Assembly

6 102-065* 1 LH Bogie Weldment (170-865) 1/8” NPT Grease Zerk

102-066* 1 RH Bogie Weldment (170-865) 1/8” NPT Grease Zerk 7 134-824 2 Spindle, 3-3/8” x 17-3/4” 8 172-396 2 10-Bolt Hub 9 172-361 1 Inside Bearing Race; HM218210 10 174-784 10 Wheel Stud, 3/4” 11 170-920 10 Wheel Nut, 3/4” 12 170-922 1 Outside Bearing Race; HM212011 13 170-921 2 Outside Bearing Cone; HM212049 14 170-927 2 Spindle Nut, Inner; DANA# M10HM101 15 170-928 2 Lock Washer; DANA# M10HM100 16 173-005 2 Spindle Nut, Outer; DANA# M10HN102 17 170-926 2 Dust Cap; Mtg Hrd: 5/16” x 3/4” Bolt (Qty 6) 18 172-362 2 Grease Seal 19 172-360 2 Inside Bearing Cone; HM218248 20 175-174 4 Wheel, 22.5 x 13.00, 10 Hole, 1.5 Neg Offset 21 171-653 4 Tire, 385-65R Truck Recap w/ Rib Hwy Tread 22 174-577 4 Tube, Tire (not shown) 23 174-979 4 Weigh Bar; 2.875”

* Used on undercarriages with 6-1/2” diameter axle tubes. Units before 5085-055 and 50100-070 may have been retrofited. If the axle is 8” in diameter, order replacement parts using page 8.

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Input Shaft and Pinion Gear Drive Parts

REF PART NO QTY DESCRIPTION

1 175-079 2 Flange Bearing, Ecc. Lock 1 3/4”;

Mtg Hrd: 1/2” x 1 3/4” B, LW, Nut (6EA)(5073 only)

175-079 3 Flange Bearing, Ecc. Lock 1 3/4”;

Mtg Hrd: 1/2” x 1 3/4” B, LW, Nut (6EA)(5085 & 50100 only)

172-288

2 Flange Bearing, Ecc. Lock 1 1/2”; Mtg Hrd: 1/2” x 1 3/4” B, LW, Nut (6EA)

2 141-044 1 Bearing Mount Plate; Mtg Hrd: 1/2” x 1 1/4”B,FW,LW,Nut (2EA)(5073 only)

141-245 1 Bearing Mount Plate;

Mtg Hrd: 1/2” x 1 1/4”B,FW,LW,Nut (2EA)(5085 & 50100 only)

3 141-600 1 Shaft; 1 3/4 “ x 108 1/2” (5073 only)

141-495 1 Shaft; 1 3/4 “ x 120 13/16” (5085 & 50100 only) 141-294

1 Shaft; 1 1/2 “ x 108 1/2”

4 170-019 1 Key; 1/2” x 1/2” x 2”

170-052

1 Key; 3/8” x 3/8” x 2 1/8”

5 175-082 1 U-Joint Assembly; Mtg Hrd: 1/2” x 5/8” set screw (170-249) (2EA)

175-124 2 Yoke; 1 3/4”, 1/2” KW 174-909 1 Cross & Bearing Kit

174-907

1 U-Joint Assembly 174-925A1 Yoke; 1 1/2”, 3/8” KW 175-124A1 Yoke; 1 3/4”, 1/2” KW 174-909A1 Cross & Bearing Kit

6 141-136 1 Trash Guard 7 170-019 1 Key; 1/2” x 1/2” x 2” 8 174-873 1 Gearbox; 4 1/4:1 ratio, Mtg Hrd: (174-911) M12 x 45MM B(10EA) 9 141-549 2 Gearbox Spacer 10 140-955 1 Gearbox Mount; Mtg Hrd: 3/4” x 2”B,LW,(6EA) 11 171-934 2 Snap Ring; 3” External, Waldes 5100 Series 12 141-388 1 Oil Slinger; 3”ID (Weld to Pinion Gear) 13 141-291 1 Pinion Gear; 3” ID 14 136-040 AR Shim; 1/8” x 3” x 4 1/4”

172-367 AR Shim; 1/16” x 3” x 4 1/4”

15 141-465 1 O-Ring; 5/16” x 50”

Used on Units Before Serial Number (5073-066)

Gearbox

5073TR 005907 R060706

1084

REF PART NO QTY DESCRIPTION

174-873 1 Gearbox Assembly, 4.25:1 1 175-014 1 Gear, Bevel, Pinion set 2 175-015 1 Casting 3 175-016 10 Bolt, HEXHD, M10 x 22MM 8.8 4 174-904 2 Plug, 1/2” Gas 5 175-017 1 Cover 6 175-018 1 Elbow 90o, 1/2” Gas 7 173-344 1 Bolt, HEXHD, M10 x 25MM 8.8 8 174-905 1 Oil Filler Plug, 1/2” Gas 9 175-020 16 Bolt, HEXHD, M12 x 35MM 8.8 10 175-021 2 Cover 11 175-022 1 Seal, Lip, 80MM x 110MM x 10MM 12 175-023 1 Shaft 13 175-024 3 Shim, 125.5 x 139.5 14 175-025 2 Bearing, 30216 15 175-026 1 Bearing, 32313 16 175-027 1 Bearing, 32212 17 175-028 1 Seal, Oil, 50MM x 110MM x 12MM 18 175-029 1 Nut, M60 x 2MM 19 175-030 1 Cap, 110MM x 10MM 20 175-031 1 Gearcase, Oil Slinger

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Auger Drive and Tower Assembly Parts

Serial Number (5073-A0012, 5085-064, 50100-083 and After)

REF PART NO QTY* DESCRIPTION

1 103-985 1 Auger Drive Shaft; 5” Dia 2 174-784 6 Stud, Wheel;3/4” x 3 1/8” 3 103-981 1 Front Tower; Mtg Hrd: 174-948 Plow Bolt, 3/4” x 2-1/2” (23ea)

103-982 1 Rear Tower; Mtg Hrd: 174-948 Plow Bolt, 3/4” x 2-1/2” (23ea) 4 141-595 2 Bearing, Plastic; 5”ID x 5” 5 174-980 2 Quad-Ring Seal; 5”ID 6 141-872 3 Thrust Washer 7 141-868 1 Thrust Plate 8 141-048 1 Inspection cover; Mtg Hrd: 5/16” x 3/4” SSB (3EA) 9 171-935 24’** Foam Rubber Seal; 3/8” x 3/4” (48’ Total for unit) 10 103-817 1 Bull Gear 11 142-727 AR Shim (7Ga)

142-728 AR Shim (14Ga) 12 174-981 1 Washer; 3/16” x 8” OD x 5 1/16” ID

* Quantity shown is for 1 Tower Assembly ** Sold By Linear Foot.

Continued on next page

Auger Drive and Tower Assembly Parts

Used on Units,Serial Number (5073-A0012, 5085-064, 50100-083 and After)

5073TR 005907 R060706

REF PART NO QTY* DESCRIPTION

13 172-289 1 Snap Ring; 5” External, Waldes 5100 series 14 174-769 2 Magnet (4 Total for unit) 15 180-768** Copper Grease Line 1/4”;(Front Upper Plate 87“, Front Upper Bearing 87”,

Front Lower Bearing 84”) (Rear Upper Plate 99“, Rear Upper Bearing 99”,

Rear Lower Bearing 96”) 46’ Total for unit. 16 170-865 3 Grease Zerk 1/8” NPT 17 174-762 3 Pipe Coupling; 1/8” STD NPT (weld on) 18 172-024 3 Straight Adapter; 1/8” NPTF F x 1/8” NPTF F 19 173-583 12 Straight Adapter; 1/4” Tube x 1/8” NPTF M

175-344 3 Grommet, Rubber; 1” x 1/4” x 1/4”(Not Shown) 20 170-244 3 Washer, 3/8” 21 142-240 A/R Shim

* Qty shown is for 1 Tower Assembly (3 grease line assemblies per tower) ** Sold By Linear Foot.

Kuhn Knight, Inc.

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5073TR 005907 R060706

Auger Drive and Tower Assembly Parts

Used on Units,Serial Number (5073-A0011, 5085-063, 50100-082 and Before)

REF PART NO QTY* DESCRIPTION

1 103-806 1 Auger Drive Shaft; 5” Dia 2 174-784 6 Stud, Wheel;3/4” x 3 1/8” 3 141-084 1 Thrust Washer, Nylon; 7-3/4” OD x 5-1/16” ID x 3/8”

300-059 1 Thrust Washer Kit - Retrofit

4 103-820

1 Thrust Plate

5 103-811 1 Front Tower; Mtg Hrd: 174-948 Plow Bolt,3/4” x 2 1/2”, LN (23EA)

103-812 1 Rear Tower; Mtg Hrd: 174-948 Plow Bolt,3/4” x 2 1/2”, LN (23EA)

6 141-595 2 Bearing, Plastic; 5”ID x 4 15/16”

141-046

2 Bearing, Plastic; 5”ID x 3-11/16” 7 174-980 2 Quad-Ring Seal; 5”ID 8 141-048 1 Inspection cover; Mtg Hrd: 5/16” x 3/4” SSB (3EA) 9 180-768 1 Copper Grease Line, 1/4”(Front Upper Auger 87“ Rear Upper Auger 99)

(Front Lower Auger 84“ Rear Lower Auger 96“)32’ Total for unit.

181-036**

Copper Grease Line; 3/16” (Front Upper Auger 87“ Rear Upper Auger 99)

(Front Lower Auger 84“ Rear Lower Auger 96“)32’ Total for unit. 10 170-865 2 Grease Zerk 1/8” NPT 11 172-024 3 Straight Adapter; 1/8” NPTF F x 1/8” NPTF F

* Quantity shown is for 1 Tower Assembly ** Sold By Linear Foot.

Not used in current production. Used on units before Serial number (5073-069, 5085-056, & 50100-072)

Used on units S/N 5073-A0026, 5085-A0005 and 50100-A0004.

Continued on next page

+ 30 hidden pages

Kuhn Rikon 5085, 5073, 50100 User Manual

Table Of Contents

Abbreviations

Using This Service Parts Listing

Body Parts

Light Kit

Wheel and Hub Parts - 5073

Input Shaft and Pinion Gear Drive Parts

Gearbox

Auger Drive and Tower Assembly Parts