www.krups.com
a
b
d
f
m
g
h
i
k3
l
o
e
j
k
k1
k2
d
p
n
q
1
2 3
4
7
5 6
8 9
1110
12
13
14
17
15 16
18
21 20
19
22
23 24
25
28 29
26 27
31
38
38
3230
33
36
34
35
A
B
C
37
Novo 3000 FNC2
Novo 3000 Premium FNC3
USA 8
Instructions for Use
Warranty
Guarantee of Performance
Français 19
Mode d’emploi
Garantie
Garantie de rendement
Español
Español 30
Instrucciones de uso
Garantía
Garantía de rendimiento
7
USA
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and/or
injury to persons, including the following:
•Read all instructions.
•Do not touch hot surfaces. Use handles or knobs.
•To protect against fire, electric shock and injury to persons, do not
immerse cord, plugs, or appliance in water or other liquid.
•Close supervision is necessary when any appliance is used by or
near children.
•Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the
appliance.
•Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to your nearest authorized KRUPS
Service Center for examination, repair or adjustment (see
Guarantee of Performance).
•The use of accessory attachments not recommended by KRUPS
may result in fire, electric shock or injury to persons.
•Do not use outdoors.
•Do not let cord hang over edge of table or counter, or touch hot
surfaces.
•Do not place on or near a hot gas or electric burner, or in a heated
oven.
•To disconnect, turn switch to “OFF”, then remove plug from wall
outlet.
•Do not use appliance for other than intended use.
•Use extreme caution when dispensing hot steam.
SAVE THESE INSTRUCTIONS
8
CAUTION
•This appliance is for household use only. Any servicing other than
routine cleaning and user maintenance should be performed by
authorized KRUPS service personnel only (see Guarantee of
Performance).
•Do not immerse base in water.
•To reduce the risk of fire or electric shock, do not remove the base
of the machine. There are no user serviceable parts inside. Repairs
should be performed by authorized KRUPS service personnel only.
SPECIAL CORD SET INSTRUCTIONS
Regarding your Cord Set:
A. A short power-supply cord is to be provided to reduce risks
resulting from becoming entangled in or tripping over a longer
cord.
B. Longer extension cords are available and may be used if care is
exercised in their use.
C. If a long extension cord is used, (1) the marked electrical rating
of the extension cord should be at least as great as the electrical
rating of the appliance, (2) the longer cord should be arranged
so that it will not drape over the counter top or table top where
it can be pulled on by children or tripped over.
D. This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended
to fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to modify the
plug in any way.
9
Description
a Lid
b Removable water container
c Water level indicator
d Warming plate for cups
e Control selector
f On/Off indicator light (red)
g Temperature control light (orange)
h On/Off switch
i Brewing head
j Steam nozzle
k Auto cappuccino accessory
K1 dial
K2 flexible tube
K3 outlet nozzle
l Removable overflow grid
m Removable drip tray
n Measuring spoon
o Filter baskets for one or two cups
p Filter holder for ground coffee
q ESE filter holder and filter system
Safety recommendations
• Read these instructions carefully before
using your espresso machine.
• Do not plug the machine into anything other
than a grounded electrical socket. Verify that
the voltage indicated on the technical
specifications plate on the bottom of the
unit corresponds to your electrical
installation.
• Do not place your espresso machine on a
hot surface (an electrical heating plate for
example) or near a flame.
• Do not use the machine without the drip
tray and drip tray grid in place.
• Unplug the machine while cleaning.
• Ensure that the electrical cord does not
come into contact with sharp or hot objects.
Do not disconnect the electrical plug by
pulling on the cord.
10
• Avoid touching the electrical cord as well as
any other part which may become hot
during the use of the machine (steam
nozzle).
• Never plunge the machine in water.
• Keep the machine and the electrical cord out
of children’s reach.
• For descaling, adhere to the directions which
follow.
• Do not use the machine if it is damaged or if
the cord is in bad condition.
• The cord or any other defective element
must be replaced exclusively by an
authorized Krups service center. Under no
circumstances should you open the machine
yourself.
Espresso coffee
Your new Krups espresso machine has been
constructed to make cafe quality espresso,
cappuccino and latte at home. Espresso
coffee is richer in aroma and stronger than
normal coffee. It is drunk from small preheated espresso cups. Hot water is passed
through the ground coffee to obtain this
delicious foamy, black coffee, which has an
invigorating effect.
You can recognize an espresso by its
characteristic aroma and its typical light brown
“crema” found on top of the coffee. But this
requires high pressure and an excellent
espresso coffee which has been well roasted
and correctly ground. If you cannot buy
ground espresso coffee, use a coffee grinder
to grind the beans. The coffee must not be
ground too fine. It must be slightly
granulated. If it is too fine, you risk blocking
the grid of the brewing head and the filter.
To guarantee complete success for your
espresso, you must also use freshly-drawn
water (so that it has not had time to stagnate
in the air), without any chlorine odor and at a
fairly cold temperature.
Before first using your machine
Before using your appliance for the first time,
clean the water heating system (without
coffee in the filter holder and filling the water
container once or twice) as follows:
• Open the lid and lift out the water container
using the handle (1). Fill the water container
with fresh, cold water (2).
• Replace the water container back into the
appliance by positioning it firmly in the
water container compartment (3) and close
the lid.
The water level in the water container can be
checked at any time using the window
provided for this purpose, so if necessary you
can add more water (4).
• Turn on the appliance (5). The red operating
light and the orange temperature control
indicator light will both come on.
• Place one of the filter baskets in the filter
holder (6). Then put the filter holder up
against the appliance’s brewing head.
• To ensure that the filter holder is in the
correct position, turn the handle so it points
to the left at a 45 degree angle (6), place
the filter holder flat against the brewing
head, then turn the handle towards the right
(7) as far as it can go (8).
• Place a container, as large as possible,
beneath the filter holder (9).
• As soon as the orange indicator light goes
off, turn the selector to the
setting (10)
and allow all the water in the water
container to run through.
• If necessary, you can stop the operation by
turning the selector to the O setting to
empty the container, then resume operation.
Using the various functions of
your espresso machine
1. ESPRESSO FUNCTION
. WITH GROUND COFFEE
For best results, we recommend that you first
pre-heat the accessories (filter holder, filter
basket and cups) without putting in
ground coffee. To do this :
• Fill the water container with fresh, cold
water (1) (2) (3) and turn on the appliance
(5). Empty the cups.
• Put the filter holder and an empty filter
basket in place (6) (7) (8), and place the
espresso cups underneath.
• As soon as the appliance reaches the correct
temperature the orange indicator light will
go out.
• Turn selector to the setting (10).
• When the cups are full of hot water, reset
the selector to the O setting.
After making your first espresso and the
appliance is hot, the espresso cups can then
be pre-heated on the cup warming plate.
. Preparing an espresso :
• Fill the water container (1) (2) (3) and turn
on the appliance (5).
• Put the filter basket for one or two cups into
the filter holder (6) .
• Place some ground coffee in the filter basket
(1 or 2 measuring scoops), and then tamp it
down firmly; the coffee should reach the lip
of the filter (12) (13).
• Remove any ground coffee which is lying
around the filter (14).
• Replace the filter holder into the machine.
Turn the filter holder until it is firmly locked
into place. (16).
• Place one or two espresso cups beneath the
filter holder.
As soon as the appliance reaches the correct
temperature the orange indicator light will go
out.
• Then turn the selector to the
setting
(17).
• When the cups are full, reset the selector to
the O setting.
• Remove the filter holder and the filter from
the machine, and take out the coffee
grounds (18).
The filter basket can be refilled to make more
espressos.
Caution: if the water container is empty
and the pump is running, you will hear a
very distinct noise, which is louder than
the normal operating sound. If this
happens, turn the machine “off”. Check
the water container and refill as needed.
Never let the pump run when the water
container is empty as this can damage the
pump.
11
If you are preparing more than one cup of
espresso, disregard the orange thermostat
light. It simply indicates that the thermostat is
regulating the temperature.
ESPRESSO FUNCTION WITH THE SPECIAL “ ESE “
FILTER HOLDER
“ESE”, which stands for “Easy Serving
Espresso”, is a selected measure of coffee,
ground and pressed between two filter papers
making a coffee pod which is ready to use (for
example “illy pods). This system makes it
easy for you to prepare your espresso and to
clean the appliance.
The E.S.E. system was designed for making
Italian-style “espresso ristretto” or “short
espresso”. The amount of coffee is about two
ounce and the water should take 20 seconds
to run through.
We do not intend, or recommend, that
the ESE servings are used for making a
“long espresso”.
We recommend that you take care when
handling and storing the ESE servings so that
they do not become deformed.
For best results, we recommend that you preheat the accessories (filter holder, filter basket
and cups) without any coffee. To do this:
• Fill the water container with fresh, cold
water (1) (2) (3) and turn on the appliance
(5).
• Put the empty ESE filter in place (7) (8) (9)
and position the espresso cup underneath.
Once the appliance reaches the correct
temperature, the orange temperature control
light will go out.
• Then turn the selector to the
(10).
• When the cup is full of hot water, reset the
selector to the O setting.
Once the machine has heated up, the
espresso cups can be pre-heated on the cup
warming plate (on top of the machine).
. Preparing an espresso:
Place the serving of “illy in the ESE filter
holder fitted with its own filter. The wording
“illy must be pointing towards the bottom.
Setting the ESE pod
Placing the ESE pod correctly will create a
richer, thicker crema.
setting
Tear excess paper from pod at perforated
edge. Place the ESE pod with the RED
MARKING FACE DOWN (bend the paper
corners down).
LOCKING the handle TIGHTLY and PROPERLY
will avoid leakage from the filter holder and
ensure a better brewing cycle.
Place the filter holder inside the brewing head
and FIRMLY turn the handle as far RIGHT as
possible.
Once the appliance reaches the correct
temperature, the orange temperature control
light will go out.
• Then turn the selector to the setting
(10).
• When the recommended quantity of coffee
has been reached (about two ounce) turn
the selector to the O position.
Remove the ESE filter holder from the brewing
head and throw away the used coffee pod.
NOTE: Other pods (such as those sold by
Starbucks ) can be used in your Krups Novo
3000 & 3000 Premium as long as they are
E.S.E. standard pods.
illy is a registered trademark of illy espresso of the
americas, inc.
Starbucks is a registered trademark of the
Starbucks Coffee Company.
2. STEAM FUNCTION FOR PREPARING CAPPUCCINO
LATTE
AND
The thumping noise which occurs while steam
is being produced comes from the
intermittent regulation of the pump and has
no effect on the proper working of the
appliance.
If you wish to make an espresso immediately
after using the steam function, the appliance
must first be allowed to cool down in order to
achieve the correct temperature for preparing
an espresso.
• To do this, place a container below the filter
holder (without coffee) and position
correctly, then turn the selector to the
setting (10).
• Allow the water to flow through until the
orange indicator light comes on. Then turn
the selector to the O setting.
12
After this, you can make another espresso.
Caution: during and after use of the
machine, the metallic parts of the steam
nozzle can become burning hot.
. Using the Krups Auto Cappuccino
accessory (model FNC3 only)
The Auto-Cappuccino accessory makes it easy
to produce frothy milk for making
cappuccinos, lattes and hot chocolates.
The milk is drawn in through the flexible
tube and heated with the aid of steam
before coming out via the outlet nozzle
of the auto cappuccino accessory.
If the flexible tube is immersed directly in a
carton of milk, a single cup is enough to
prepare a cappuccino or a latte. You can
adjust the amount of froth of the milk by
using the dial of this auto cappuccino
accessory.
It is best to use fresh, skim or low-fat milk, not
boiled, and well chilled (kept in the
refrigerator). The container must also be cold
(do not run it under hot water before frothing
the milk).
For heating thick liquids, please refer to the
section “Heating thick liquids (e.g. soup)”
We recommend that you clean the auto
cappuccino accessory immediately after use please refer to section “Cleaning the
Machine”.
If you are making a cappuccino or latte, you
will need at least a 5 oz. cup (150 ml).
Cappuccino is made using 1/3 espresso, 1/3
hot steamed milk and 1/3 frothed milk. Café
latte is made using 1/2 espresso, 1/2 steamed
milk, and topped with a bit of frothy milk.
• Fill the water container with fresh, cold
water (1) (2) (3) and turn on the appliance
(5).
• Move the nozzle to the exterior of the
appliance and mount the auto cappuccino
accessory on the nozzle (22).
• Turn the dial to the
• Immerse the flexible tube in the milk to be
setting (23).
heated (you can use the Krups container or
any other container) (24).
Once the appliance reaches the right
temperature, the orange temperature control
light will go out.
• Hold the container under the steam nozzle
equipped with the cappuccino accessory in
such a way that the tip is immersed in the
milk.
• Turn the selector to the
setting (26).
Keep the container straight during this
operation. Do not allow the tip of the
nozzle to touch the bottom of the container
because this could obstruct the steam
output.
• Once you have obtained the desired
quantity of frothy milk, turn the selector to
the O setting.
• After use, remove the flexible tube from the
container and clean the auto cappuccino
accessory (see section “Cleaning the
Machine”).
. Preparing hot, steamed milk for a cafe
latte, hot chocolate or for heating water
(for tea, for example).
Notes:
. Hot chocolate: immerse the flexible tube
directly into the carton if the chocolate milk is
ready-made, or heat the milk if you are using
powdered chocolate. Then mix the powder in
the heated milk.
• Move the nozzle to the exterior of the
appliance and mount the auto cappuccino
accessory on the nozzle (19).
• Fill the water container (1) (2) (3) and turn
on the appliance (5).
• Turn the selector to the setting (20) .
• Turn the dial of the auto cappuccino
accessory to the fine end of the setting
scale (27).
• Immerse the flexible tube in the liquid to be
heated. The tube must touch the bottom of
the container.
• Place a container under the outlet nozzle.
Once the appliance reaches the right
temperature, the orange temperature control
light will go out.
• Turn the selector to the steam setting
(21).
• Once you have obtained the desired
quantity of frothy milk, turn the selector to
the O setting.
13
• After use, remove the flexible tube from the
container.
. Using the Krups patented Perfect Froth
Attachment
Krups patented Perfect Froth attachment Is
available on all models. For the FNC3 model
you will need to remove the auto-cappuccino
attachment and replace It by the Perfect Froth
Attachment in order to execute this operation
(36).
You can use the Perfect Froth attachment to
froth milk for cappuccinos, Lattes and hot
chocolates as well as heating any liquid (water
for tea or thick liquids for soups)
• Fill the water container (1) (2) (3) and start
the appliance (5).
• Move the steam nozzle to the exterior of the
appliance.
• Turn the selector to the setting
Once the appliance reaches the correct
temperature, the orange temperature control
light will go out.
• Immerse the steam nozzle in the container
holding the liquid to be heated.
• Then turn the selector to the
setting (21)
until the liquid is hot enough, then reset the
selector to the O setting and remove the
container.
• For liquids other than water, turn the
selector to the setting
(20) for the
following cleaning operation in order to
prevent any blockage of the opening of the
steam nozzle :
• place an empty container below the steam
nozzle.
• select the
setting again (21) to remove
the residue of the liquid.
• turn the selector to the setting O.
• Clean the steam nozzle with a damp cloth.
• For more thorough cleaning of the nozzle,
please refer to the paragraph on
maintenance.
Cleaning the Machine
- Never wash your espresso machine
accessories in the dishwasher.
14
(20).
After use, the water container must be
emptied.
. Removable drip tray
After using the appliance, remove the
overflow grid and empty the removable drip
tray (30) (31). If several espressos are being
prepared one after the other, the drip tray
should be emptied from time to time (about
once every 7 - 8 espressos). If necessary, clean
the drip tray and its grid with water and a
little non-abrasive dishwashing liquid, rinse
and dry. When reassembling the machine,
ensure that the plastic lining is in the right
place (32).
. The brewing head, the filter basket and
the filter holder
These must be cleaned after each use. All you
need to do is wipe a damp cloth over the
brewing head of your appliance and to wash
the other accessories in water and a little nonabrasive dishwashing liquid, rinse and dry.
If the brewing head is heavily clogged up,
unscrew the grid using a coin, clean it and
refit it, pressing down firmly (33).
When your espresso machine is not being
used, do not leave the filter holder in the
appliance to prevent wear on the gasket.
. The cup warming plate: remove this to
clean it with water and a little non-abrasive
dishwashing liquid, rinse and dry (34).
. Steam nozzle: wipe with a damp cloth after
each use.
. The auto cappuccino accessory
After each use, we recommend that you rinse
the auto cappuccino accessory in the
following manner:
• Turn the selector to the steam pre-heating
position
• Turn the dial to the cleaning position (37).
• Immerse the flexible tube into a glass of
(19).
water. (The minimum quantity necessary is 3
to 4 ounces/30-60 ml).
• Place an empty container below the outlet
nozzle.
Once the appliance reaches the correct
temperature, the orange temperature control
light will go out.
• Then turn the selector to the steam setting
(26).
• When all the water has run through the
auto cappuccino accessory turn the selector
to the O position.
• After use, remove the flexible tube from the
container.
• Once this operation is completed, clean the
outlet nozzle with a damp cloth.
We recommend that you regularly dismantle
the auto cappuccino accessory and clean it
with water, a little non-abrasive dishwashing
liquid and a small brush. Rinse and dry before
reassembling it (38).
Be careful to mount the flexible tube the
right way: engage the straight cut end into
the auto cappuccino accessory.
. Brewing head gasket
From time to time this gasket must be
cleaned :
• Put the filter basket in the filter holder and
place the filter holder in the machine.
• Place a container under the filter holder.
• Turn on the appliance.
• Turn the selector to the setting .
• When the hot water starts to filter through,
turn the filter holder slowly from left to right
so that the water filters through between
the gasket and the filter.
Descaling
• Descaling of your espresso machine should
be done fairly frequently with citric or
tartaric acid.
The guarantee does not include espresso
machines which do not function, or do
not function properly, because descaling
has not been carried out.
However, we would advise you to use the
Krups descaling solution which is available
from Krups. Descaling depends on the
hardness of the water, but also on the
frequency of use.
- Then follow the following method:
• Unscrew the grid from the brewing head of
the appliance and clean it.
• Dissolve 2 tsp/10 ml of the descaling product
or a packet of KRUPS descaling solution, in
17 oz/510 ml of lukewarm water and pour
the whole batch into the empty water
container.
• Place a container under the brewing head.
Run through about 1/3 of the liquid
immediately, setting the selector to the
position
• Stop the appliance, leaving the position (10)
(10).
engaged and wait for 10 - 15 minutes to
allow the descaler to take effect.
• Next, start the machine again and allow the
rest of the liquid to run through.
• Then rinse with two water containers of
fresh water and replace the grid on the head
of the appliance (see section on “Cleaning
the Appliance”).
Problems, probable causes and
how to correct them
Problems Probable causes Corrective actions
Espresso not hot Cups, filter and Preheat the
enough filter holder accessories (cups,
Coffee leaks The filter holder See paragraph
around the filter is not mounted «Preparing an
holder correctly or has espresso».
Pump is very noisy No water in the Fill the water tank.
are cold. filter, filter holder)
See paragraph
«Preparing an
espresso».
not been tightened
sufficiently.
There are coffee Clean around the
grounds on the filter and the
edge of the filter gasket.
The brewing head Clean the gasket
gasket is dirty. with a damp cloth.
The brewing Contact an
head gasket approved Krups
is defective service centre.
water tank.
Water tank incor- Press firmly down
rectly mounted. on the water tank.
Coffee grounds too Use fresh coffee
old or very dry
and the pump cannot produce
pressure.
15
Water does not run No water in the Fill the water tank.
through water tank. Press firmly down
Water tank incor- on the water tank.
rectly mounted.
The filter is blocked, Clean the filter and
the coffee grounds the grid on the
are too fine or head.
tamped down too See the paragraph
hard. «Maintenance»
and try a coarser
coffee.
Brewing head Put the grid to
grid is encrusted soak in descaling
solution
See paragraph
«Maintenance».
Appliance needs See paragraph
descaling. «Descaling».
Water runs through Coffee grounds too Try a finer coffee
too quickly coarse
Quantity of Use the spoon
ground coffee provided to
is insufficient. measure out the
coffee.
Coffee grounds not Tamp down the
tamped down coffee again.
firmly enough
The espresso has Coffee grounds Try a finer-ground
no froth (crema on too coarse coffe
coffee)
Coffee grounds Tamp down the
not tamped coffee again
Coffee grounds Use fresh coffee
stale or too dry
The milk is not very Steam nozzle bloc- See paragraph
frothy ked «Maintenance»
Cappuccino acces- See paragraph
sory blocked «Maintenance»
Milk not fresh. Use fresh milk
Milk is lukewarm. Put milk in
refrigerator.
Lots of water on Grounds not Tamp down the
the coffee grounds properly tamped grounds
down
Insufficient quantity Increase the
of ground coffee quantity of ground
coffee.
Recipes
Savor your espresso just as you like it: when
you want to relax or to top off a good meal.
Here are a few recipes which you will be able
to create with your espresso machine.
. Original espresso
• Take one measuring spoonful of good
quality well roasted espresso coffee, and
make an espresso directly into a pre-heated
cup.
If you use good, finely ground coffee, the cup
will be crowned by a fine head of golden
froth (crema).
• Add sugar if desired and enjoy.
. Cappuccino
For a state of the art cappuccino, the ideal
quantities are as follows: 1/3 coffee, 1/3 hot,
steamed milk, 1/3 frothy milk.
• Use 5 oz. cups/150 ml which have been pre-
heated.
• Fill them with 1/3 espresso coffee. Using
the auto cappuccino accessory, fill the cup
with another 1/3 of steamed milk and 1/3
of froth.
• Lastly, sprinkle with drinking chocolate
powder or cinnamon.
. Cafe latte
For a state of the art latte, the ideal quantities
are as follows: 1/2 coffee, 1/2 hot, steamed
milk topped with some frothed milk.
• Prepare a classic espresso in a large cup.
• Add steamed milk.
• Top with some froth.
. Iced coffee à l’Italienne
4 vanilla ice cubes, 2 cups of cold, sweetened
espresso, 4 ounces milk, fresh cream, grated
chocolate.
• Mix the cold espresso with milk.
• Distribute the ice cubes among the glasses,
pour the coffee over them and decorate
with fresh cream and grated chocolate.
. Friesian coffee
• Add a small glass of rum to a sweetened
cup of espresso.
16
• Top with a good layer of fresh cream and
serve.
Limited One Year Warranty
Your KRUPS # FNC2/FNC3 is covered by the
following warranty :
If within one year from date of purchase this
KRUPS product fails to function because of
defects in materials or workmanship, KRUPS
North America will, at its option, repair or
replace the unit without charge, provided the
owner has a proof of date of purchase.
This warranty will be void if malfunction was
caused by damage to the product by accident,
misuse, use on frequency or voltage other
than marked on the product and/or described
in the instructions, abuse including tampering,
damage in transit, or use for commercial
purposes. This warranty gives you specific
legal rights, and you may also have other
rights which may vary from state to state.
17
Loading...