Kraus KHF41033 User Manual
INSTALLATION GUIDE
Stainless Steel Farmhouse
Kitchen Sink
KHF410-30 / KHF410-33 / KHF410-36
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. July 2, 2018
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep teh box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
DO NOT RETURN TO STORE
Please contact our Customer Service Team
1-800-775-0703 / customerservice@kraususa.com
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
1
Prior to Installation:
Phillips screwdriver
Adjustable wrench
Phillips screwdriver
Hex wrench
Silicone Sealant
A
I
D
J
F
B
G
C
H
E
• Inspect the sink prior to installation to make sure the sink has not been damaged
during shipping
• Use the cut-out template provided by Kraus
• Observe all plumbing and building codes according to your state requirement
• Additional oor and wall preparation may be required to avoid damaging the
product
• Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse
base cabinets should be 3” larger than the actual size of the sink
• Not recommended to be installed with laminate countertop
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or Customerservice@kraususa.com
The step-by-step guidelines in the installation instructions are a general reference for installing a
Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to
install all Kraus products by hiring a licensed professional.
Tools you will need:
Safety Goggles
Phillips Screwdriver
Drill
Tape Measure
Silicone Adhesive Jig Saw
Pencil
Screwdriver
Acetone
Level
2
Parts List
• Cut-Out Template • Bottom Grid • Drain • Drain Cap • Mounting hardware
Dimensions
27-7/8” 30-7/8”
708mm 784mm
29-7/8” 32-7/8”
759mm 835mm
KHF410-30
*
29-7/8” x 20-3/4” x 10”
Min Cabinet Size: 33”
Matching Grid: KBG-410-30
Drain Model #: ST-1
Drain Cap: STC-2
33-7/8”
860mm
35-7/8”
911mm
17-1/4”
9”
438mm
229mm
20-3/4”
10”
527mm
254mm
438mm
17-1/4”
20-3/4”
527mm
KHF410-33
32-7/8” x 20-3/4” x 10”
Min Cabinet Size: 36”
Matching Grid: KBG-410-33
Drain Model #: ST-1
Drain Cap: STC-2
17-1/4”
9”
438mm
229mm
20-3/4”
10”
527mm
254mm
9”
10”
229mm
254mm
KHF410-36
*
35-7/8” x 20-3/4” x 10”
Min Cabinet Size: 39”
Matching Grid: KBG-410-36
Drain Model #: ST-1
Drain Cap: STC-2
Typical note: = Special Order
*
3
1. Determine Reveal Type
3/8“ Positive Reveal
DETERMINE REVEAL TYPE
Flushed/Zero Reveal
3/8“ Positive Reveal
DETERMINE REVEAL TYPE
Flushed/Zero Reveal
3/8“ Positive Reveal
1/8“ Negative Reveal
DETERMINE REVEAL TYPE
Use scissors to cut along the line of the paper template for your desired reveal type
(Negative, Positive, or Flushed Reveal)
KRAUS Recommended Installation Type
3/8” Positive Reveal
3/8” Positive
Flushed/Zero Reveal
1/8” Negative Reveal
Flushed/Zero
1/8” Negative
Centerline
2. Position Template
• Check the cut-out template against the actual sink to ensure a proper sized cut-out
• Place the cut-out template in the desired location on the countertop
NOTE: Make sure
clearance is suitable for
backsplash, faucet, and
plumbing for the sink
4