Kramer VS-34FD User Manual

P/N: 2900-301210 Rev 2 www.kramerAV.com

USER MANUAL

MODEL:

VS-34FD
Modular Matrix Switcher with I/O Flexible
Module Slots

Kramer Electronics Ltd.

VS-34FD – Contents

i

Contents

Introduction 1

Getting Started 1
Overview 2

Defining VS-34FD Modular Matrix Switcher 4
Mounting VS-34FD 7
Connecting VS-34FD 8

Port Numbering 9
Connecting to VS-34FD via RS-232 10
Connecting to VS-34FD via USB (VCOM) 10
Connecting to VS-34FD via Ethernet 10

Operating and Controlling – Front Panel 13

Starting Up 13
Changing Action Confirmation Mode 14
Switching – Front Panel 14
Locking Front Panel Buttons 17
Copying EDID – Front Panel 17
Restarting – Front Panel 18
Performing Factory Reset – Front Panel 18
Viewing Device Information – Front Panel 18

Operating and Controlling – Embedded Web Pages 19

Browsing Web Pages 20
Switching – Web Pages 22
Copying EDID – Web Pages 28
Configuring Ports 29
Configuring Advanced Port Settings 29

Input / Output Card Hardware Installation Instructions 31
Upgrading VS-34FD Firmware 32

Upgrading Firmware – Embedded Web Pages 32
Upgrading Firmware – K-Upload 32

Default EDID 33

H2-IN2-F34 / H2-OUT2-F34 33
H2A-IN2-F34 / H2A-OUT2-F34 34
DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34 35
DTAxrD2-IN2-F34 / DTAxrD2-OUT2-F34 37
F676-IN2-F34 / F676-OUT2-F34 38
DTAXRD2P-OUT2-F34 40

Technical Specifications 42

VS-34FD Chassis 42
H2-IN2-F34 / H2-OUT2-F34 42
H2A-IN2-F34 / H2A-OUT2-F34 43
DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34 43
DTAxrD2-IN2-F34 / DTAxrD2-OUT2-F34 44
DTAxrD2P-OUT2-F34 45
F676-IN2-F34 / F676-IN2-F34 46
VGAA-IN2-F34 / VGAA-OUT2-F34 46
SDIA-IN2-F34 47
Default Communication Parameters 47

Protocol 3000 48

Understanding Protocol 3000 48
Protocol 3000 Commands 49
Result and Error Codes 61

Kramer Electronics Ltd.

VS-34FD – Introduction

1

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

• Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.

• Review the contents of this user manual.

Go to www.kramerav.com/downloads/VS-34FD to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).

Achieving Best Performance

• Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).

• Do not secure the cables in tight bundles or roll the slack into tight coils.

• Avoid interference from neighboring electrical appliances that may adversely influence

signal quality.

• Position your Kramer VS-34FD away from moisture, excessive sunlight and dust.

Safety Instructions

Caution:

• This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.

• For products with relay terminals and GPI\O ports, please refer to the permitted rating
for an external connection, located next to the terminal or in the User Manual.

• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.

• Disconnect the power and unplug the unit from the wall before installing.

• Do not open the unit. High voltages can cause electrical shock! Servicing by qualified

personnel only.

• To ensure continuous risk protection, replace fuses only according to the rating
specified on the product label which located on the bottom of the unit.

Kramer Electronics Ltd.

VS-34FD – Introduction

2

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling.

Overview

Congratulations on purchasing your Kramer VS-34FD Modular Matrix Switcher with I/O
Flexible Module Slots.

VS-34FD is a high performance, 34-port, 8K-ready, multi-format, modular matrix switcher for

AV signals, The modular chassis features 17 module card slots for installing a full range of
signal formats. All slots support both input and output module cards, enabling the matrix to be
populated as 2x32, 32x2 or any other configuration in between in increments of two inputs or
two outputs. The chassis includes a control module, a test module that can monitor and test
any input and output in the matrix, and an additional redundant power supply for optional
installation.

Benefits and Features

• High-Performance Modular Matrix Switcher – Professional, 8K-ready matrix for switching
multi-format AV signals. Features Kramer Equalization & re-Klocking™ Technology that
rebuilds the digital signal to travel longer distances.

For optimum range and performance, use recommended Kramer cables.

• Modular & Fully Flexible Platform – Select from a full array of popular and legacy formats
to populate the chassis, including HDMI™, HDBaseT, fiber optic, VGA, SDI, as well as
analog and digital audio. All slots support both input and output slots, enabling the matrix
to be populated as 2 x 32, 32 x 2 or any configuration in between. This matrix is
compatible with existing modular matrix modules.

• Flexible Infrastructure Conversion – Kramer Core™ technology enables copper, fiber or
twisted pair to be used at the same time, according to input/output module selection. The
matrix receives signals from compatible Kramer transmitters, automatically converts
between available infrastructure options and sends the signals to compatible Kramer
receivers.

• Quick and Efficient Management – Compatible with Kramer Network enterprise
management platform providing: Automatic discovery through the network, FW upgrade
management for matrix and cards, identification of card type and location, indication of
card status (module ID, actual firmware versions), matrix switching, specific card
features configuration (for example, volume levels on audio cards), store and recall of
predefined switching scenarios, integrated Maestro automation, and more.

Kramer Electronics Ltd.

VS-34FD – Introduction

3

• Content Protection Support – HDCP 2.2 compliant, with compatible HDMI, HDBaseT,
fiber optic, VGA, and SDI modules. Supports disabling HDCP when needed.

• Fast Switching Support on Outputs – Reduces or removes switching delay.

• EDID Management – Individual EDID management per input. Captures and stores the

EDID from a display device.

• Second Power Supply – Redundant, hot-swappable for optional installation.

• Flexible Control Options – Local control from the front panel, including switching,

executing multiple switches simultaneously, storage and recall of multiple switching
configurations, front panel lockout. Distance control with user-friendly web GUI via
Ethernet and Protocol 3000 API via Ethernet or RS–232.

• Modular Cooling System – 2 easily replaceable, low-noise, hot-swappable fan racks.

• Cost-Effective Maintenance – Power LEDs and LCD display facilitate easy local

maintenance and troubleshooting. Local FW upgrade via mini USB port and reset button
for convenient unit reset ensure lasting, field-proven deployment.

• Easy Installation – 19” enclosure for rack mounting in a 3U rack space with included rack
ears and universal 100-240V AC power supply.

Typical Applications

VS-34FD is ideal for the following typical applications:

• Professional display systems requiring video signal routing.

• Broadcast, presentation, and production facilities, as well as monitoring in large

duplication systems.

• Rental/staging applications.

Kramer Electronics Ltd.

VS-34FD – Defining VS-34FD Modular Matrix Switcher

4

Defining VS-34FD Modular Matrix Switcher

This section defines VS-34FD.

Figure 1: VS-34FD Modular Matrix Switcher Front Panel

#

Feature

Function

Numeric Keypad
(When not in menu mode, these
buttons are for numeric input.)

Press 1 to 0 to enter port numbers for routing or to enter values for
navigating the LCD menu.

Press ◄ (backward) to shift the LCD display to the right (the LCD display
only shows 13 of the available matrix combinations).

Press ► (forward) to shift the LCD display to the left (the LCD display only
shows 13 of the available matrix combinations).

Menu Function Buttons
(After pressing the MENU
button four times, these buttons
light and are enabled.)

ALL

Press to switch an input to all outputs (see Switching an Input to

All Outputs – Front Panel on page 16).

OFF

Press to turn off an output.

STO

Press to store the current setup in a preset.

RCL

Press to recall a preset.

EDID

Press to copy an EDID from any input or output to any input
(see Copying EDID – Front Panel on page 17).

DELAY

Press to set the delay between confirming an action and the
execution of the action.

ESC Button

Press to exit the current menu operation.

ENTER Button

Press to complete the input-output setup when using a one-digit number
instead of two digits. For example, to enter input 5, you can press either 05
or 5, ENTER.
Press to enter the options in a setup menu.

10 111

15

16

17

18

19 20

12 13 14

6

7

8 9

2

3

4

5

1

4

7

5

8

6

9

0

2 3

1 2 3 4 5 6 7

8

9

Kramer Electronics Ltd.

VS-34FD – Defining VS-34FD Modular Matrix Switcher

5

#

Feature

Function

EXIT MENU Button

Press to exit a menu or return to switching mode.

DEFAULT SETUP Button

Press to open the reset menu on the display.

TAKE Button

When flashing, press to confirm actions.

MENU Button

Press once to enable the ALL, OFF, STO and RCL buttons.
Press again to enter the configuration menu.
When in a menu, press to cycle through the menu items.

LOCK Button

Press and hold for approximately 2 sec to lock/unlock the front panel
buttons.

OUTPUTS/INPUTS
LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row).
Displays user interface messages and menus.

SERVICE Mini USB Connector

Use for controlling the matrix switcher and for firmware upgrade
(see Upgrading VS-34FD Firmware on page 32).

POWER LED

Lights yellow when the power supply is active and the device is powered on.

ERROR LED

Lights red when an error is detected. Briefly lights red immediately following
a power disruption (e.g., cable disconnection, power off, and so on).

PS-1 Power Module

Supplies power to the device.

PS-2 Power Module

Supplies power to the device.

10

11

12

13

14

15

16

17

18

19

20

Kramer Electronics Ltd.

VS-34FD – Defining VS-34FD Modular Matrix Switcher

6

Figure 2: VS-34FD Modular Matrix Switcher Back Panel

#

Feature

Function

PS-2 Power Module and Switch

Connect to the mains power supply (for the PS-1 power module) and use
switch to power the unit.

PS-1 Power Module and Switch

Connect to the mains power supply (for the PS-2 power Module) and use
switch to power the unit.

You can connect PS-1 and/or PS-2.
If one of them fails to operate, the other can power the unit.

48V DC Harness Connector

Connect to the PS-4812 PoE power supply add-on.

RS-232 9-pin D-sub Port

Connect to the remote operation PC or a controller.

RESET Recessed Button

Press to reboot the VS-34FD control card.

NET 1 RJ-45 Connector

Connect to a PC or controller via the Ethernet LAN (100Mb).

NET 2-1G RJ-45 Connector

Connect to a PC or controller via the Ethernet LAN (100/1000Mb).

IN/OUT Connector Cards
(2x17)

Insert an input or output card and connect sources/acceptors to the HDMI™
and/or AUDIO 3.5mm mini jacks to create a flexible matrix switcher (ranging
from 2x32 to 32x2).

Different card types are available.

Each port in a card operates independently.
Card slots support hot-plug connection, so the device immediately

identifies a card as IN or OUT.

AUDIO 3.5mm mini jacks can be set as inputs or outputs (the output is

the HDMI audio embedded audio) when a source/acceptor is connected.

The port numbers are fixed. Each card has 2 ports and they are
numbered accordingly (for example, in the card located under 19-20, the top
port is 19 and the lower one is 20).

21

22

26

24 2825

ININ IN IN IN IN IN INOUT OUT OUT OUT OUT OUT OUT OUT OUTCTRL

2723

48V

21

22

23

24

25

26

27

28

Kramer Electronics Ltd.

VS-34FD – Mounting VS-34FD

7

Mounting VS-34FD

This section provides instructions for mounting VS-34FD. Before installing, verify that the
environment is within the recommended range:

• Operation temperature – 0 to 40C (32 to 104F).

• Storage temperature – -40 to +70C (-40 to +158F).

• Humidity – 10% to 90%, RHL non-condensing.

Caution:

• Mount VS-34FD before connecting any cables or power.

Warning:

• Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for
the device.

• Avoid uneven mechanical loading.

• Appropriate consideration of equipment nameplate ratings should be used for avoiding

overloading of the circuits.

• Reliable earthing of rack-mounted equipment should be maintained.

To mount the VS-34FD in a rack:

 Attach both rack ears by removing the screws from each side of the

machine and replacing those screws through the rack ears or place the
machine on a table.

For more information go to www.kramerav.com/downloads/VS-34FD

Kramer Electronics Ltd.

VS-34FD – Connecting VS-34FD

8

Connecting VS-34FD

Figure 3: Connecting to the VS-34FD Rear Panel

For optimum range and performance use the recommended Kramer cables available at

www.kramerav.com/product/VS-34FD.

Using third-party cables may cause damage!

The configuration of HDMI input/output cards shown in (Figure 3) is merely a sample
representation and different input / output cards may be mixed as required. For card
installation instructions, see Input / Output Card Hardware Installation Instructions
on page 31.

To connect the VS-34FD as illustrated in the example in Figure 3:

1. Insert the input and output cards into the card slots .

2. Connect 32 video sources (for example, a Blu-ray player and media player) and 2 video
acceptors, (for example, a video display and a projector), 2 video sources and 2 video
acceptors, or any configuration in between.

3. If required, connect a PC or remote controller to the RS-232 port (see Connecting to

VS-34FD via RS-232 on page 10) and/or the Ethernet port (see Connecting to VS-34FD
via Ethernet on page 10).

4. Connect the power cord.

5. If necessary, review and set the system configuration using the Menu (see Using the

Configuration Menus on page 24).

29

Kramer Electronics Ltd.

VS-34FD – Connecting VS-34FD

9

Port Numbering

All cards have two physical ports. Numbering of ports is sequential from top to bottom and left
to right.

Figure 4: Sample Port Numbering

Diagram #

Actual Port Number

1

IN 1

2

IN 2

3

IN 3

4

IN 4

5

OUT 5

6

OUT 6

7

IN 7

8

IN 8

Kramer Electronics Ltd.

VS-34FD – Connecting VS-34FD

10

Connecting to VS-34FD via RS-232

You can connect to the VS-34FD via an RS-232 connection using, for example, a PC. Note
that a null-modem adapter/connection is not required.

To connect to the VS-34FD via RS-232:

• Connect the RS-232 9-pin D-sub Port on the VS-34FD unit via a 9-wire straight cable
(only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 need to be connected) to the
RS-s232 9-pin D-sub port on your PC.

Connecting to VS-34FD via USB (VCOM)

The device’s SERVICE Mini USB Connector can work as a virtual COM (VCOM) port.
Verify that the USB port on the PC that connects to VS-34FD is configured as a VCOM port.
You may need to install a driver to do this. You can use a tool such as Hercules or K-Config to
use Protocol 3000 commands over USB (see Protocol 3000 on page 48). You can also use
K-Upload to upgrade firmware over USB (see Upgrading Firmware – K-Upload on page 32).

Connecting to VS-34FD via Ethernet

You can connect to VS-34FD via Ethernet using either of the following methods:

• Directly to the PC using a crossover cable (see Connecting Ethernet Port Directly to a

PC on page 10).

• Via a network hub, switch, or router, using a straight-through cable (see Connecting

Ethernet Port via a Network Hub or Switch on page 12).

If you want to connect via a router and your IT system is based on IPv6, speak to your IT
department for specific installation instructions.

Connecting Ethernet Port Directly to a PC

You can connect the Ethernet port of VS-34FD directly to the Ethernet port on your PC using
a crossover cable with RJ-45 connectors.

This type of connection is recommended for identifying the

VS-34FD with the factory configured default IP address.

After connecting VS-34FD to the Ethernet port, configure your PC as follows:

1. Click Start > Control Panel > Network and Sharing Center.

2. Click Change Adapter Settings.

3. Highlight the network adapter you want to use to connect to the device and click Change
settings of this connection.

24

16

Kramer Electronics Ltd.

VS-34FD – Connecting VS-34FD

11

The Local Area Connection Properties window for the selected network adapter appears
as shown in Figure 5.

Figure 5: Local Area Connection Properties Window

4. Highlight either Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4
(TCP/IPv4) depending on the requirements of your IT system.

5. Click Properties.
The Internet Protocol Properties window relevant to your IT system appears as shown in

Figure 6 or Figure 7.

Figure 6: Internet Protocol Version 4 Properties Window

Kramer Electronics Ltd.

VS-34FD – Connecting VS-34FD

12

Figure 7: Internet Protocol Version 6 Properties Window

6. Select Use the following IP Address for static IP addressing and fill in the details as
shown in Figure 8.
For TCP/IPv4 you can use any IP address in the range 192.168.1.1 to 192.168.1.255
(excluding 192.168.1.39) that is provided by your IT department.

Figure 8: Internet Protocol Properties Window

7. Click OK.

8. Click Close.

Connecting Ethernet Port via a Network Hub or Switch

You can connect the Ethernet port of VS-34FD to the Ethernet port on a network hub or using
a straight-through cable with RJ-45 connectors.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

13

Operating and Controlling – Front Panel

VS-34FD enables you to operate and control your matrix from the front panel buttons.

You can also operate and control VS-34FD via Protocol 3000 commands (see Protocol 3000

Commands on page 49) and via the embedded web pages (see Operating and Controlling –
Embedded Web Pages on page 19).

VS-34FD enables you to do the following:

• Starting Up on page 13.

• Switching – Front Panel on page 14.

• Locking Front Panel Buttons on page 17.

• Copying EDID – Front Panel on page 17.

• Restarting – Front Panel on page 18.

• Performing Factory Reset – Front Panel on page 18.

• Viewing Device Information – Front Panel on page 18.

Starting Up

To start up VS-34FD:

1. Turn on the power switch.
The LCD display shows a series of screens as VS-34FD is booting up and then it

displays the last video input/output routing setup that was used.

KRAMER ELECTRONICS Co.,LTD

VS-34FD MATRIX

Loading Main Setup

PLEASE WAIT

VOSW:

01

02

03

04

05

06

07

08

VISW:

11

12

13

14

15

16

17

Figure 9: Default Startup Status Display Sequence

An output with no corresponding input shown under it indicates that this output is not
routed to any input.

2. Press the MENU Button twice to see the last audio input/output routing setup that
was used.

3. If there are more than 13 input/outputs in the matrix, press the ◄ (backward) and ►
(forward) Buttons to shift the LCD display to the right or left.

13

1

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

14

Changing Action Confirmation Mode

VS-34FD enables you to configure whether an action needs to be confirmed before the

system executes it. By default, switching is executed in At Once mode, in which actions are
implemented immediately upon pressing the relevant buttons. In Confirm mode, after pressing
the relevant buttons, the TAKE Button flashes, and the action are not implemented until you
press the TAKE Button.

At Once mode is the default for all actions except storing and recalling presets, where the
default is Confirm mode.

Failure to press the TAKE Button within a few seconds results in the action timing out.

To change the action confirmation mode:

• Press the TAKE Button .
The action confirmation mode changes.

If the TAKE Button is flashing, you cannot change the confirmation mode.

Switching – Front Panel

VS-34FD enables you to switch inputs to outputs using the Numeric Keypad .

The following rules apply when using the Numeric Keypad:

• When entering a single digit number (for example 5), you can either press 0 followed by
5, or 5 followed by the ENTER Button .

• Pressing 00 (or 0, ENT) is only relevant for an input and is used to disconnect the
currently entered output number from the input.

• The ESC Button is used to cancel an operation without affecting the current status.
For example, if you enter an incorrect number by mistake, press the ESC Button to
cancel the operation.

• At any stage, if no button is pressed within approximately 15 seconds, the automatic
timeout causes VS-34FD to exit the operation and revert to the output/input display.

VS-34FD enables you to do the following:

• Switching Video – Front Panel on page 15.

• Switching Audio – Front Panel on page 15.

• Switching an Input to All Outputs – Front Panel on page 16.

• Turning Off Outputs – Front Panel on page 16.

• Storing and Recalling Presets – Front Panel on page 16.

• Delaying Switching Actions on page 17.

12

1 9 8

8

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

15

Switching Video – Front Panel

VS-34FD enables you to switch the video signal from inputs to outputs using the front panel

buttons.

Press the MENU Button once to display all available input and output ports for switching
video.

To switch video using the front panel buttons:

1. On the Numeric Keypad , press the number of the desired output.
The in/out routing appears on the right side of the LCD display with the input blank.

VOSW:

01

02

03

04

05

06

07

08

VISW:

11

12

13

14

15

16

17

IN__=>OUT01

Figure 10: Video Output Entered

2. Press the number of the desired input.
The input is displayed and the video is switched.

VOSW:

01

02

03

04

05

06

07

08

VISW:

11

12

13

14

15

16

17

IN16=>OUT01

Figure 11: Video Input Entered

Switching Audio – Front Panel

VS-34FD enables you to switch the audio from inputs to outputs using the front panel buttons.

Press the MENU Button three times to display all available input and output ports for
switching audio.

To switch audio using the front panel buttons:

1. Press the MENU Button twice.
The current audio switching setup is displayed on the LCD display.

AOSW:

01

02

03

04

05

06

07

08

AISW:

13

13

13

13

13

17

17

Figure 12: Current Audio Switching Setup

2. On the Numeric Keypad , press the number of the desired output.
The in/out routing appears on the right side of the LCD display with the input blank.

AOSW:

01

02

03

04

05

06

07

08

AISW:

13

13

13

13

13

17

17

IN__=>OUT01

Figure 13: Audio Output Entered

3. Press the number of the desired input.
The input is displayed and the video is switched.

AOSW:

01

02

03

04

05

06

07

08

AISW:

11

12

13

14

15

16

17

IN17=>OUT01

Figure 14: Audio Input Entered

13

13

1

13

1

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

16

Switching an Input to All Outputs – Front Panel

VS-34FD enables you to switch an input to all outputs at one time.

To switch an input to all outputs:

1. Press the MENU Button , four times.
The functions screen appears on the LCD display.

2. Press the ALL Button , and then press either the 1 button to switch video or the 2
button to switch audio.

3. Enter the desired input number.
All outputs are switched to the selected input.

Turning Off Outputs – Front Panel

Turning an output off means that there is no input switched to this output. This is indicated on
the display by the Input being blank underneath the relevant Output.

To turn an output off:

1. Press the MENU Button , four times.
The functions screen appears on the LCD display.

2. Press OFF on the numeric keypad.
The following message is displayed:

out__ => OFF

3. Enter the relevant output number.
The output is turned off.

VOSW:

01

02

03

04

05

06

07

08

VISW:

11

12

13

14

15

16

17

Figure 15: Out 01 Off

Storing and Recalling Presets – Front Panel

VS-34FD enables you to store (save) and recall up to 60 different input/output configurations.

To store the current input/output configuration as a preset:

1. Press the MENU Button , four times.
The functions screen appears on the LCD display.

2. Press STO and enter the preset number (1–60) under which you would like to save
the configuration.

The current input/output configuration is stored.

To recall a stored preset:

1. Press the MENU Button , four times.
The functions screen appears on the LCD display.

2. Press RCL and enter the preset number (1–60) you would like to recall.

13 2 13 3 13 4 13

5

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

17

3. Press the TAKE button .
The preset is recalled and the input/output configuration changes to the selected preset.

Delaying Switching Actions

VS-34FD enables you to set a delay time for an output which elapses between entering a

switching action and the execution of the action. This delay can be set for each output
independently. The delay is defined in units of 200ms and ranges from 0 to 15, providing
delays of up to 3 seconds (15 x 200ms = 3 seconds).

To set the execution delay for an output:

1. Press the MENU Button , four times.

2. The functions screen appears on the LCD display.

3. Press DELAY .

4. Using the numeric keys, enter the output number and number of delay units.
The execution delay for the selected output is set.

Locking Front Panel Buttons

You can lock VS-34FD to prevent tampering with the unit or prevent the settings from being
changed accidentally via the front panel buttons. When the front panel is locked, you can still
remotely operate VS-34FD via the web pages or Protocol 3000 API commands.

To lock the front panel buttons:

• Press and hold the LOCK Button until the button lights.
The front panel buttons are locked.

To unlock the front panel buttons:

• Press and hold the LOCK Button until the button is no longer lit.
The front panel buttons are unlocked.

Copying EDID – Front Panel

VS-34FD enables you to copy an EDID from any input or output to any input.

To copy an EDID:

1. Press the MENU Button , four times.
The functions screen appears on the LCD display.

2. Press the EDID Button .
The EDID Copy screen appears.

3. Enter the source number (input or output) and the destination number (input only).
The EDID is copied.

12

13 6 14

14

13

6

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Front Panel

18

Restarting – Front Panel

VS-34FD enables you to restart the device using the front panel buttons.

To restart VS-34FD:

1. Press the MENU Button , six times.
The reset screen appears.

2. Press the 1 button.
The confirm screen appears and the TAKE Button flashes.

3. Press the TAKE Button to confirm the restart.

VS-34FD restarts.

Performing Factory Reset – Front Panel

VS-34FD enables you to perform a factory reset using the front panel buttons.

To perform a factory reset:

1. Press the MENU Button , six times.
The reset screen appears.

2. Press the 2 button.
The confirm screen appears and the TAKE Button flashes.

3. Press the TAKE Button to confirm the factory reset.

VS-34FD restarts and resets to factory default settings.

Viewing Device Information – Front Panel

VS-34FD enables you to view IP and firmware information using the front panel buttons.

To view device information:

• IP Addresses – Press the MENU Button , five times and press 1 to view ETH0 IP
addresses or press 2 to view ETH1 IP addresses.

• Installed Firmware Version – Press the MENU Button , seven times.

13

12

12

13

12

12

13

13

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

19

Operating and Controlling – Embedded Web Pages

VS-34FD enables you to operate and control the device via Ethernet using built-in, user-

friendly web pages.

You can also operate and control VS-34FD via Protocol 3000 commands (see Protocol 3000

Commands on page 49) and via the front panel buttons (see Operating and Controlling –
Front Panel on page 13).

VS-34FD embedded web pages enable you to do the following:

• Browsing Web Pages on page 20.

• Switching – Web Pages on page 22.

• Copying EDID – Web Pages on page 28.

• Configuring Ports on page 29.

• Configuring Advanced Port Settings on page 29.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

20

Browsing Web Pages

If a web page does not update correctly, clear your Web browser’s cache.

To browse the web pages:

1. Connect to VS-34FD via Ethernet (see Connecting to VS-34FD via Ethernet
on page 10).

2. Type the IP address of the device in the address bar of your internet browser (default =

192.168.1.39).
If security is enabled, the Login window appears.

Figure 16: Embedded Web Pages Login Window

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

21

3. Enter the Username (default = Admin) and Password (default = Admin) and click
Sign in.

The default web page appears.

Figure 17: Default Page with Navigation Pane

4. Click the Navigation Pane on the left side of the screen to access the relevant web page.

Click the X next to the navigation pane to hide the names of the pages and the menu icon to
show the names of the pages.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

22

Switching – Web Pages

VS-34FD enables you to switch inputs to outputs using the embedded web pages.
VS-34FD web pages enable you to do the following:

• Switching Video – Web Pages on page 22.

• Switching Audio – Web Pages on page 23.

• Switching an Input to All Outputs – Web Pages on page 25.

• Configuring Audio Follow Video on page 26.

• Turning Off Outputs – Web Pages on page 26.

• Storing and Recalling Presets – Web Pages on page 27.

Switching Video – Web Pages

VS-34FD enables you to switch video signals from inputs to outputs using the embedded web

pages.

To switch video using the embedded web pages:

1. Go to the Routing Settings page.
The Routing Settings page opens with the Video switching tab open.

Figure 18: Routing Settings Page – Video Switching Tab

2. Click the circle that intersects the input and output that you want to switch.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

23

The selected circle turns green, and the video input is switched to the output.

Figure 19: Video Switching Tab – IN20 Switched to OUT25

Switching Audio – Web Pages

VS-34FD enables you to switch audio signals from inputs to outputs using the embedded web

pages.

To switch audio using the embedded web pages:

1. Go to the Routing Settings page (Figure 18).

2. Click AUDIO.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

24

The Audio switching tab appears.

Figure 20: Routing Settings Page – Audio Switching Tab

3. Click the circle that intersects the input and output that you want to switch.
The selected circle turns green, and the audio input is switched to the output.

Figure 21: Audio Switching Tab – IN28 Switched to OUT17

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

25

Switching an Input to All Outputs – Web Pages

VS-34FD enables you to switch a video or audio input to all outputs using the embedded web

pages.

To switch an input to all outputs:

1. Go to the Routing Settings page (Figure 18).

2. Click the InToALL switch.
The ALL checkboxes and circles appear.

Figure 22: Routing Settings Page – InToALL Enabled

3. Click one of the circles under the ALL checkbox.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

26

All outputs switch to the selected input.

Figure 23: Routing Settings Page – All Outputs Switched to Input 15

To switch only specific outputs to the selected input, select/deselect the checkboxes to the
right of the ALL checkbox that correspond to each output.

To return to normal switching mode, click the InToALL switch.

Configuring Audio Follow Video

VS-34FD enables you to configure audio switching to follow (mimic) the video switching, so

that whenever you switch the video using the embedded web pages, the same switching
occurs for the audio.

To configure audio switching to follow the video switching:

1. Go to the Routing Settings page (Figure 18).

2. Select the AFV checkbox.
All AFV checkboxes are selected and audio switching for all inputs is configured to follow

video switching.

To configure only specific audio outputs to follow video, select/deselect the relevant AFV
checkboxes.

Turning Off Outputs – Web Pages

VS-34FD enables you to turn off outputs, so that they are not connected to any input.

To turn off an output:

1. Go to the Routing Settings page (Figure 18).

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

27

2. Click the circle in the CLOSE row that corresponds to the output that you want to turn
off.

The selected output is turned off.

To turn off all outputs, click InToALL and click the circle under the ALL checkbox that
corresponds to CLOSE (Figure 22).

Storing and Recalling Presets – Web Pages

VS-34FD enables you to store (save) and recall up to 60 different input/output configurations.

To store the current input/output configuration as a preset:

1. Go to the Routing Settings page.

Figure 24: Routing Settings Page with Presets

2. Under PRESETS, click Save for the preset number (1–60) under which you would like to
save the configuration.

The current input/output configuration is stored.

To recall a stored preset:

• Under PRESETS, click Load for the preset number (1–60) that you would like to recall.
The preset is recalled and the input/output configuration changes to the selected preset.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

28

Copying EDID – Web Pages

VS-34FD enables you to copy an EDID from any input or output to any input using the

embedded web pages.

To copy an EDID:

1. Go to the EDID Management page.

Figure 25: EDID Management Page

2. Click an input or output in the Read From area.

-OR­Click DEFAULT to use the default EDID.

3. Click all relevant Inputs in the Copy to area.

Select the All checkbox to copy to all inputs.

4. Click COPY.
The selected EDID is copied to all selected inputs.

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

29

Configuring Ports

VS-34FD enables you to configure settings for each input or output on a module card that is

installed into the chassis.

To configure settings for a port:

1. On the Port tab of the Settings page, click the relevant port from the Port List.
The Information panel for the selected port appears.

Figure 26: Settings Page > Port Tab > Port Information Panel

2. Configure settings as needed.

You can also access a port information/configuration panel by clicking the relevant port on
the Routing Settings page (Figure 18).

Configuring Advanced Port Settings

VS-34FD enables you to configure the following advanced settings for select module cards:

• Setting HDBT Range on page 29.

• Configuring Compression Level on page 30.

• Configuring Compression Resolution on page 30.

Setting HDBT Range

These settings apply to the following input/output cards:

• DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34

• DTAxrD2-IN2-F34 / DTAxrD2-OUT2-F34

• DTAxrD2P-OUT2-F34

Kramer Electronics Ltd.

VS-34FD – Operating and Controlling – Embedded Web Pages

30

To set HDBT range:

• On the Port Information panel, under XTRA, select one of the following:

▪ ON – HDBaseT ultra-long range (to enable increased range at a reduced bandwidth).
▪ OFF – HDBaseT normal range.

Actual ranges depend on the resolution of signal. See the card technical specifications
for more information.

Configuring Compression Level

These settings apply to the following input/output cards:

• DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34

To configure compression level:

• On the Port Information panel, under XTRA, select one of the following:

▪ Standard
▪ High

Configuring Compression Resolution

These settings apply to the following input/output cards:

• DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34

To configure compression level:

• On the Port Information panel, under XTRA, select one of the following:

▪ >1080P – Compress signal resolutions higher than 1080p.
▪ ALL – Compress all signal resolutions to enable extended reach.

Kramer Electronics Ltd.

VS-34FD – Input / Output Card Hardware Installation Instructions

31

Input / Output Card Hardware Installation Instructions

VS-34FD input and output cards mount in one of the 17 slots on the rear of the VS-34FD

chassis. Slots are numbered from left to right according to the number of the ports on each
card. For example, slot one is numbered 1–2 because the card in that slot contains inputs or
outputs 1 and 2. VS-34FD slots are interchangeable, meaning that an input or an output card
can be inserted into any slot.

You can insert IN/OUT cards into slots while the device is powered.

The process for inserting cards is the same for all cards. The diagram below is for illustration
purposes only.

To install an input / output card:

1. Power off the machine and all devices connected to it.

2. Use a Phillips screwdriver, loosen the screws at the top and bottom of the blanking plate.

3. Remove the blanking plate from the slot and store it for possible future use.

4. Remove the new card from its shipping box and anti-ESD bag.

5. Holding the card by the lower handle, align the card with the plastic guide rails.

6. Slide the card into the chassis until the front of the card contacts the connector inside the
chassis.

7. Press the card firmly into the slot until the connector plate is flush with the rear panel of
the chassis and the connector is fully seated.

8. Using a Phillips screwdriver, tighten the retaining screws at the top and bottom of the
card to secure it to the chassis.

9. Power on VS-34FD and configure the new card using the embedded web pages.

10. Power on the peripheral devices.

Figure 27: Input / Output Card Installation

Kramer Electronics Ltd.

VS-34FD – Upgrading VS-34FD Firmware

32

Upgrading VS-34FD Firmware

The VS-34FD chassis and module card firmware can be upgraded in the following ways:

• Upgrading Firmware – Embedded Web Pages on page 32.

• Upgrading Firmware – K-Upload on page 32.

Upgrading Firmware – Embedded Web Pages

To upgrade VS-34FD chassis firmware using the embedded web pages:

• On the Device tab of the Settings page, click Browse and select the relevant upgrade
file.

To upgrade the firmware of one of the module cards via the embedded web pages:

• On the Card tab of the Settings page, click Browse and select the relevant upgrade file.

Upgrading Firmware – K-Upload

VS-34FD enables upgrading device and card firmware via RS-232, USB (VCOM) or Ethernet

using the K-Upload software application, available at

www.kramerav.com/product/VS-34FD#Tab_Resources.

For instructions on upgrading the firmware using K-Upload, see the K-Upload User Manual.
For information on connecting to the VS-34FD via RS-232, USB (VCOM), or Ethernet, see

(see Connecting VS-34FD on page 8).

Kramer Electronics Ltd.

VS-34FD – Default EDID

33

Default EDID

H2-IN2-F34 / H2-OUT2-F34

Model name............... VS-34H2

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2014, ISO week 255

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (Reserved - 0x00)

-------------------------

DDC/CI................... Not supported

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

Report information

Date generated........... 5/11/2021

Software revision........ 2.60.0.972

Data source.............. Real-time 0xF100 - NB: improperly installed

Operating system......... 6.2.9200.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,18,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,

Kramer Electronics Ltd.

VS-34FD – Default EDID

34

45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,48,32,0A,20,20,20,20,20,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,B7

H2A-IN2-F34 / H2A-OUT2-F34

Monitor

Model name............... VS-34H2A

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2014, ISO week 255

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (CEA/CTA-EXT)

-------------------------

DDC/CI................... n/a

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

EIA/CEA/CTA-861 Information

Revision number.......... 3

IT underscan............. Supported

Basic audio.............. Supported

YCbCr 4:4:4.............. Not supported

YCbCr 4:2:2.............. Not supported

Native formats........... 1

Detailed timing #1....... 1920x1080p at 60Hz (16:10)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Detailed timing #2....... 1920x1080i at 60Hz (16:10)

Kramer Electronics Ltd.

VS-34FD – Default EDID

35

Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Detailed timing #3....... 1280x720p at 60Hz (16:10)

Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync

Detailed timing #4....... 720x480p at 60Hz (16:10)

Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz

CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001

CE vendor specific data (VSDB)
IEEE registration number. 0x000C03

CEC physical address..... 1.0.0.0

Maximum TMDS clock....... 165MHz

CE speaker allocation data

Channel configuration.... 2.0

Front left/right......... Yes

Front LFE................ No

Front center............. No

Rear left/right.......... No

Rear center.............. No

Front left/right center.. No
Rear left/right center... No

Rear LFE................. No

Report information

Date generated........... 11/05/2021

Software revision........ 2.91.0.1043

Data source.............. File - NB: improperly installed

Operating system......... 10.0.18362.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,18,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,48,32,41,0A,20,20,20,20,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,96,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,77

DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34

Monitor

Model name............... VS-34DTAxrC2

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2014, ISO week 255

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (CEA/CTA-EXT)

-------------------------

DDC/CI................... n/a

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Kramer Electronics Ltd.

VS-34FD – Default EDID

36

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

EIA/CEA/CTA-861 Information

Revision number.......... 3

IT underscan............. Supported

Basic audio.............. Supported

YCbCr 4:4:4.............. Not supported

YCbCr 4:2:2.............. Not supported

Native formats........... 1

Detailed timing #1....... 1920x1080p at 60Hz (16:10)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Detailed timing #2....... 1920x1080i at 60Hz (16:10)

Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Detailed timing #3....... 1280x720p at 60Hz (16:10)

Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync

Detailed timing #4....... 720x480p at 60Hz (16:10)

Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz

CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001

CE vendor specific data (VSDB)
IEEE registration number. 0x000C03

CEC physical address..... 1.0.0.0

Maximum TMDS clock....... 165MHz

CE speaker allocation data

Channel configuration.... 2.0

Front left/right......... Yes

Front LFE................ No

Front center............. No

Rear left/right.......... No

Rear center.............. No

Front left/right center.. No

Kramer Electronics Ltd.

VS-34FD – Default EDID

37

Rear left/right center... No

Rear LFE................. No

Report information

Date generated........... 11/05/2021

Software revision........ 2.91.0.1043

Data source.............. File - NB: improperly installed

Operating system......... 10.0.18362.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,18,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,44,54,41,78,72,43,32,0A,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,99,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,77

DTAxrD2-IN2-F34 / DTAxrD2-OUT2-F34

Monitor

Model name............... VS-34DTAxrD2

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2014, ISO week 255

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (CEA/CTA-EXT)

-------------------------

DDC/CI................... n/a

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD

Kramer Electronics Ltd.

VS-34FD – Default EDID

38

1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

EIA/CEA/CTA-861 Information

Revision number.......... 3

IT underscan............. Supported

Basic audio.............. Supported

YCbCr 4:4:4.............. Not supported

YCbCr 4:2:2.............. Not supported

Native formats........... 1

Detailed timing #1....... 1920x1080p at 60Hz (16:10)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Detailed timing #2....... 1920x1080i at 60Hz (16:10)

Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Detailed timing #3....... 1280x720p at 60Hz (16:10)

Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync

Detailed timing #4....... 720x480p at 60Hz (16:10)

Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz

CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001

CE vendor specific data (VSDB)
IEEE registration number. 0x000C03

CEC physical address..... 1.0.0.0

Maximum TMDS clock....... 165MHz

CE speaker allocation data

Channel configuration.... 2.0

Front left/right......... Yes

Front LFE................ No

Front center............. No

Rear left/right.......... No

Rear center.............. No

Front left/right center.. No
Rear left/right center... No

Rear LFE................. No

Report information

Date generated........... 11/05/2021

Software revision........ 2.91.0.1043

Data source.............. File - NB: improperly installed

Operating system......... 10.0.18362.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,18,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,44,54,41,78,72,44,32,0A,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,98,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,77

F676-IN2-F34 / F676-OUT2-F34

Monitor

Model name............... VS-34F676

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2014, ISO week 255

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Kramer Electronics Ltd.

VS-34FD – Default EDID

39

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (CEA/CTA-EXT)

-------------------------

DDC/CI................... n/a

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

EIA/CEA/CTA-861 Information

Revision number.......... 3

IT underscan............. Supported

Basic audio.............. Supported

YCbCr 4:4:4.............. Not supported

YCbCr 4:2:2.............. Not supported

Native formats........... 1

Detailed timing #1....... 1920x1080p at 60Hz (16:10)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Detailed timing #2....... 1920x1080i at 60Hz (16:10)

Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Detailed timing #3....... 1280x720p at 60Hz (16:10)

Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync

Detailed timing #4....... 720x480p at 60Hz (16:10)

Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz

CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)

Kramer Electronics Ltd.

VS-34FD – Default EDID

40

640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001

CE vendor specific data (VSDB)
IEEE registration number. 0x000C03

CEC physical address..... 1.0.0.0

Maximum TMDS clock....... 165MHz

CE speaker allocation data

Channel configuration.... 2.0

Front left/right......... Yes

Front LFE................ No

Front center............. No

Rear left/right.......... No

Rear center.............. No

Front left/right center.. No
Rear left/right center... No

Rear LFE................. No

Report information

Date generated........... 09/02/2021

Software revision........ 2.91.0.1043

Data source.............. File - NB: improperly installed

Operating system......... 10.0.18363.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,18,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,46,36,37,36,0A,20,20,20,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,88,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,77

DTAXRD2P-OUT2-F34

Model name............... VS-34DTAxrD2P

Manufacturer............. KMR

Plug and Play ID......... KMR1200

Serial number............ 295-883450100

Manufacture date......... 2019, ISO week 9

Filter driver............ None

-------------------------

EDID revision............ 1.3

Input signal type........ Digital

Color bit depth.......... Undefined

Display type............. Monochrome/grayscale

Screen size.............. 520 x 320 mm (24.0 in)

Power management......... Standby, Suspend, Active off/sleep

Extension blocs.......... 1 (CEA/CTA-EXT)

-------------------------

DDC/CI................... Not supported

Color characteristics

Default color space...... Non-sRGB

Display gamma............ 2.20

Red chromaticity......... Rx 0.674 - Ry 0.319

Green chromaticity....... Gx 0.188 - Gy 0.706

Blue chromaticity........ Bx 0.148 - By 0.064

White point (default).... Wx 0.313 - Wy 0.329

Additional descriptors... None

Timing characteristics

Horizontal scan range.... 30-83kHz

Vertical scan range...... 56-76Hz

Video bandwidth.......... 170MHz

CVT standard............. Not supported

GTF standard............. Not supported

Additional descriptors... None

Preferred timing......... Yes

Native/preferred timing.. 1920x1080p at 60Hz (16:9)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA

Kramer Electronics Ltd.

VS-34FD – Default EDID

41

640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD

EIA/CEA/CTA-861 Information

Revision number.......... 3

IT underscan............. Supported

Basic audio.............. Supported

YCbCr 4:4:4.............. Not supported

YCbCr 4:2:2.............. Not supported

Native formats........... 1

Detailed timing #1....... 1920x1080p at 60Hz (16:10)

Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync

Detailed timing #2....... 1920x1080i at 60Hz (16:10)

Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Detailed timing #3....... 1280x720p at 60Hz (16:10)

Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync

Detailed timing #4....... 720x480p at 60Hz (16:10)

Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz

CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001

CE vendor specific data (VSDB)
IEEE registration number. 0x000C03

CEC physical address..... 1.0.0.0

Maximum TMDS clock....... 165MHz

CE speaker allocation data

Channel configuration.... 2.0

Front left/right......... Yes

Front LFE................ No

Front center............. No

Rear left/right.......... No

Rear center.............. No

Front left/right center.. No
Rear left/right center... No

Rear LFE................. No

Report information

Date generated........... 04/10/2021

Software revision........ 2.91.0.1043

Data source.............. Real-time 0xF900 - NB: improperly installed

Operating system......... 10.0.17763.2

Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,09,1D,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,56,
53,2D,33,34,44,54,41,78,72,44,32,0A,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,89,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,77

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

42

Technical Specifications

VS-34FD Chassis

BANDWIDTH

Supports up to 50Gbps (12.5Gbps per graphic channel), depending
on the cards used.

CONTROLS

Front panel buttons, RS-232, Ethernet

POWER CONSUMPTION

100-240V AC, 50/60Hz, 3.7A

OPERATING TEMPERATURE

0° to +55°C (32° to 131°F)

STORAGE TEMPERATURE

–45° to +72°C (–49° to 162°F)

HUMIDITY

10% to 90%, RHL non-condensing

COOLING

Forced air, fan

ENCLOSURE TYPE

Aluminum

RACK MOUNT

With supplied rack ears

DIMENSIONS

19” 6U (48.3cm x 36cm x 26.6cm W, D, H)

SHIPPING DIMENSIONS

60cm x 49.3cm x 39cm

PRODUCT WEIGHT

13.54kg (29.85lbs) approx.

SHIPPING WEIGHT

14.9kg (32.85lbs) approx.

VIBRATION

ISTA 1A in carton (International Safe Transit Association)

SAFETY REGULATORY
COMPLIANCE

CE

ENVIRONMENTAL REGULATORY
COMPLIANCE

Complies with appropriate requirements of RoHs and WEEE
INCLUDED ACCESSORIES

Power cord

OPTIONAL ACCESSORIES

For optimum range and performance use recommended Kramer
cables available at www.kramerav.com/product/VS-34FD

Specifications are subject to change without notice at www.kramerav.com

H2-IN2-F34 / H2-OUT2-F34

INPUTS/OUTPUTS

2 HDMI: On female HDMI connectors

VIDEO

Max Data Rate: 18Gbps (6Gbps per graphics channel)

Max Resolution: 4K@60Hz (4:4:4)

HDMI Support: 3D, Deep Color, x.v.Color™, ARC, Dolby® TrueHD,
Dolby Digital Plus, DTS–HD®, and 7.1 multi–channel audio

Content Protection: HDCP 2.2/1.4 compliant

EXTENSION LINE
Range at 4K60 (4:2:0) or 4K30 (4:4:4) Resolution: 10m (32ft)

Range at 1080p 12-bit (deep color) Resolution: 15m (49ft)

POWER

Consumption: 5W

ENVIRONMENTAL CONDITIONS

Operating Temperature: 0° to +40°C (32° to 104°F)

Storage Temperature: –40° to +70°C (–40° to 158°F)

Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

Safety: CE
PRODUCT DIMENSIONS

12.90cm x 24.90cm x 2.00cm (5.08" x 9.80" x 0.79") W, D, H

PRODUCT WEIGHT

0.2kg (0.5lbs) approx.

SHIPPING DIMENSIONS

16.50cm x 34.50cm x 5.90cm (6.50" x 13.58" x 2.32") W, D, H

SHIPPING WEIGHT

0.4kg (0.9lbs) approx.

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

43

H2A-IN2-F34 / H2A-OUT2-F34

INPUTS/OUTPUTS

• 2 HDMI: On female HDMI connectors

PORTS

• 2 Analog Audio: On 3.5mm mini jacks

VIDEO

• Max Data Rate: 18Gbps (6Gbps per graphics channel)

• Max Resolution: 4K@60Hz (4:4:4)

• HDMI Support: 3D, Deep Color, x.v.Color™, ARC, Dolby®

TrueHD, Dolby Digital Plus, DTS–HD®, and 7.1 multi–channel
audio

• Content Protection: HDCP 2.2/1.4 compliant

EXTENSION LINE

• Range at 4K60 (4:2:0) or 4K30 (4:4:4) Resolution: 10m (32ft)

• Range at 1080p 12 bit (deep color) Resolution: 15m (49ft)

POWER

Consumption: 5W

ENVIRONMENTAL CONDITIONS

• Operating Temperature: 0° to +40°C (32° to 104°F)

• Storage Temperature: –40° to +70°C (–40° to 158°F)

• Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

Safety: CE
PRODUCT DIMENSIONS

12.90cm x 24.90cm x 2.00cm (5.08" x 9.80" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.2kg (0.5lbs) approx.

SHIPPING DIMENSIONS

16.50cm x 34.50cm x 5.90cm (6.50" x 13.58" x 2.32" ) W, D, H

SHIPPING WEIGHT

0.4kg (0.9lbs) approx.

DTAxrC2-IN2-F34 / DTAxrC2-OUT2-F34

INPUTS/OUTPUTS

• 2 HDBaseT: On RJ–45 connectors

PORTS

• 2 Unbalanced Audio: On a 6–pin terminal block connector

• 2 RS-232: On a 6–pin terminal block connector

• 2 IR: On a 4–pin terminal block

• 1 Ethernet: On an RJ–45 connector

EXTENSION LINE

• Standard Compression: Up to 100m (330ft) at 4K@60Hz
(4:4:4), 4K@60Hz (4:2:0) or 4K@30Hz (4:4:4)

• Up to 180m (590ft) at full HD (1080p @60Hz 24bpp)

• High Compression: Up to 100m (330ft) at 4K@60Hz (4:4:4), or

4K@60Hz (4:2:0)

• Up to 180m (590ft) at 4K@30Hz (4:4:4)

• Up to 200m (650ft) at full HD (1080p @60Hz 24bpp)

• No Compression: Up to 100m (330ft) at 4K@60Hz (4:2:0)

• Up to 180m (590ft) at full HD (1080p @60Hz 24bpp)

• Standards Compliance: HDBaseT 1.0

When using recommended Kramer cables

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

44

VIDEO

• Max Data Rate: Up to 18Gbps (6Gbps per graphic channel),
10Gbps CSC over CAT cable

• Standard Compression Max Resolution: 4096x2160@60Hz
(4:4:4) 24bpp

• High Compression Max Resolution: 3840x2160@60Hz (4:4:4)
24bpp

• No-Compression Max Resolution: 4096x2160@60Hz (4:2:0)
24bpp

• Compliance: HDCP 2.2, HDR 10

• HDMI Support: Deep color, x.v.Color™, lip sync, HDMI

uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K,
4K, and 3D as specified in HDMI 2.0

EXTENDED ETHERNET

Bandwidth: Up to 100Mbps

EXTENDED RS-232

Baud Rate: 300 to 115200

POWER

Consumption: 21.5W

OPERATING TEMPERATURE:

0° to +40°C (32° to 104°F)

STORAGE TEMPERATURE:

–40° to +70°C (–40° to 158°F)

HUMIDITY:

10% to 90%, RHL non-condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

• Safety: CE

• Environmental: Complies with appropriate requirements of

RoHs and WEEE

DIMENSIONS

25.00cm x 13.00cm x 2.00cm (9.84" x 5.12" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.3kg (0.7lbs) approx.

SHIPPING DIMENSIONS

16.50cm x 34.50cm x 5.90cm (6.50" x 13.58" x 2.32" ) W, D, H

SHIPPING WEIGHT

0.5kg (1.1lbs) approx.

DTAxrD2-IN2-F34 / DTAxrD2-OUT2-F34

INPUTS/OUTPUTS

• 2 HDBaseT: On RJ–45 connectors

PORTS

• 2 Unbalanced Audio: On a 6–pin terminal block connector

• 2 RS-232: On a 6–pin terminal block connector

• 2 IR: On a 4–pin terminal block

• 1 Ethernet: On an RJ–45 connector

EXTENSION LINE

• Compression: Low–level standard DSC compression for signals
above 4K@60 (4:2:0)

• 4K@60 (4:4:4) Range with Compression: Up to 100m (330ft)

• 4K@60 (42:0) Range with No Compression: Up to 100m (330ft)

• Full HD (1080p@60Hz) Range with No Compression: Up to

130m (430ft),

• Full HD (1080p@60Hz) Range in Ultra−Long Mode: Up to
180m (590ft)

• Compliance: HDBaseT 2.0

• Note: Use Kramer shielded cables to achieve optimum

extension ranges

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

45

VIDEO

• Max Bandwidth with Compression: 17.95Gbps (5.98Gbps per
graphic channel)

• Max Bandwidth with No Compression: 10.2Gbps (3.4Gbps per
graphic channel)

• Max Resolution with Compression: 3840x2160@60Hz 4:4:4
24bpp

• Max Resolution with No Compression: 4096x2160@60Hz 4:2:0
24bpp

• Compliance: HDCP 2.2, HDR 10

EXTENDED ETHERNET

Bandwidth: Up to 100Mbps

EXTENDED RS-232

Baud Rate: 300 to 115200

POWER

Consumption: 21.5W

ENVIRONMENTAL CONDITIONS

• Operating Temperature: 0° to +40°C (32° to 104°F)

• Storage Temperature: –40° to +70°C (–40° to 158°F)

• Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

• Safety: CE

• Environmental: Complies with appropriate requirements of

RoHs and WEEE

PRODUCT DIMENSIONS

25.00cm x 13.00cm x 2.00cm (9.84" x 5.12" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.2kg (0.5lbs) approx.

SHIPPING DIMENSIONS

29.30cm x 16.50cm x 5.90cm (11.54" x 6.50" x 2.32" ) W, D, H

SHIPPING WEIGHT

0.4kg (0.9lbs) approx.

DTAxrD2P-OUT2-F34

INPUTS/OUTPUTS

• 2 HDBaseT: On RJ–45 connectors

PORTS

• 2 Unbalanced Audio: On a 6–pin terminal block connector

• 2 RS-232: On a 6–pin terminal block connector

• 2 IR: On a 4–pin terminal block

• 1 Ethernet: On an RJ–45 connector

EXTENSION LINE

• Compression: Low–level standard DSC compression for signals
above 4K@60 (4:2:0)

• 4K@60 (4:4:4) Range with Compression: Up to 100m (330ft)

• 4K@60 (42:0) Range with No Compression: Up to 100m (330ft)

• Full HD (1080p@60Hz) Range with No Compression: Up to

130m (430ft),

• Full HD (1080p@60Hz) Range in Ultra−Long Mode: Up to
180m (590ft)

• Compliance: HDBaseT 2.0

• Note: Use Kramer shielded cables to achieve optimum

extension ranges

VIDEO

• Max Bandwidth with Compression: 17.95Gbps (5.98Gbps per
graphic channel)

• Max Bandwidth with No Compression: 10.2Gbps (3.4Gbps per
graphic channel)

• Max Resolution with Compression: 3840x2160@60Hz 4:4:4
24bpp

• Max Resolution with No Compression: 4096x2160@60Hz 4:2:0
24bpp

• Compliance: HDCP 2.2, HDR 10

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

46

EXTENDED ETHERNET

Bandwidth: Up to 100Mbps

EXTENDED RS-232

Baud Rate: 300 to 115200

POWER

Consumption: 21.5W

ENVIRONMENTAL CONDITIONS

• Operating Temperature: 0° to +40°C (32° to 104°F)

• Storage Temperature: –40° to +70°C (–40° to 158°F)

• Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

• Safety: CE

• Environmental: Complies with appropriate requirements of

RoHs and WEEE

PRODUCT DIMENSIONS

25.00cm x 13.00cm x 2.00cm (9.84" x 5.12" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.2kg (0.5lbs) approx.

SHIPPING DIMENSIONS

29.30cm x 16.50cm x 5.90cm (11.54" x 6.50" x 2.32" ) W, D, H

SHIPPING WEIGHT

0.4kg (0.9lbs) approx.

F676-IN2-F34 / F676-IN2-F34

INPUTS/OUTPUTS

2 Fiber Optic: On LC connectors

PORTS

2 RS-232: On a 3–pin terminal block connector

VIDEO

• Max Bandwidth: 18Gbps

• Max Resolution: 4K@60 (4:4:4)

• HDMI Support: 18Gbps (6Gbps per channel) data rate, LPCM

7.1, Dolby True HD, and DTS–HD

• Content Protection: HDCP 2.2

EXTENSION LINE

• Optical Fiber: Multi–mode (MM) or single–mode (SM)

• Optical Module: Kramer 10Gbps SFP+ IEEE 802.3ae compliant

modules (MM is included)

MULTI-MODE LINE

• Compliance: G.651.1 OFNR fiber

• Max Reach over OM3 MM Fiber: 3km (1.8 miles)

SINGLE-MODE LINE

• Compliance: G.652D OFNR fiber

• Max Reach over OS1 SM Fiber: 33km (20.5 miles)

EXTENDED RS-232

Baud Rate: 300 to 115200

USER INTERFACE

Indicators: Optical link LEDs

POWER

Consumption: 9W

ENVIRONMENTAL CONDITIONS

Operating Temperature: 0° to +40°C (32° to 104°F)
Storage Temperature: –40° to +70°C (–40° to 158°F)
Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE
(STANDARDS COMPLIANCE)

Safety: CE, UL
Environmental: RoHs, WEEE
ACCESSORIES

Included: 2 MM SFP+ transceivers

VGAA-IN2-F34 / VGAA-OUT2-F34

PORTS

• 2 VGA: On 15–pin HD connectors

• 2 Unbalanced Analog Audio: On 3.5mm mini jack connectors

(accessible via C GF/GMAF–30 cables)

BANDWIDTH

450MHz

MAXIMUM RANGE

10m (32ft)

Kramer Electronics Ltd.

VS-34FD – Technical Specifications

47

POWER CONSUMPTION

9.5W

ENVIRONMENTAL CONDITIONS

• Operating Temperature: 0° to +40°C (32° to 104°F)

• Storage Temperature: –40° to +70°C (–40° to 158°F)

• Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE

• Safety: CE

• Environmental: Complies with appropriate requirements of

RoHs and WEEE

INCLUDED ACCESSORIES

2 C–GF/GMAF–30 cables

PRODUCT DIMENSIONS

25.20cm x 13.00cm x 2.00cm (9.92" x 5.12" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.3kg (0.7lbs) approx.

SHIPPING DIMENSIONS

16.50cm x 30.00cm x 6.00cm (6.50" x 11.81" x 2.36" ) W, D, H

SHIPPING WEIGHT

0.7kg (1.4lbs) approx.

SDIA-IN2-F34

PORTS

• 2 SDI, 75Ω on BNC connectors

• 2 unbalanced analog audio on 3.5mm mini jack connectors

TOTAL BANDWIDTH

3Gbps

MAXIMUM RANGE

• 300m (980ft) — SD

• 200m (655ft) — HD 1080p

• 90m (295ft) — 3G 1080p

3D PASS THROUGH

Not supported

POWER CONSUMPTION

6W

ENVIRONMENTAL CONDITIONS

• Operating Temperature: 0° to +40°C (32° to 104°F)

• Storage Temperature: –40° to +70°C (–40° to 158°F)

• Humidity: 10% to 90%, RHL non–condensing

REGULATORY COMPLIANCE

• Safety: CE

• Environmental: Complies with appropriate requirements of

RoHs and WEEE

PRODUCT DIMENSIONS

25.20cm x 13.00cm x 2.00cm (9.92" x 5.12" x 0.79" ) W, D, H

PRODUCT WEIGHT

0.3kg (0.7lbs) approx.

SHIPPING DIMENSIONS

30.00cm x 16.50cm x 6.00cm (11.81" x 6.50" x 2.36" ) W, D, H

SHIPPING WEIGHT

0.5kg (1.0lbs) approx.

Default Communication Parameters

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

8

Command Format:

ASCII

Stop Bits:

1

Example: (Switch video input 2 to output 4): #VID 2>4<CR>

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.0.0

TCP Port #:

5000

Gateway:

192.168.0.1

Default User:

Admin

Default Password:

Admin

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

48

Protocol 3000

Kramer devices can be operated using Kramer Protocol 3000 commands sent via serial or
Ethernet ports.

Understanding Protocol 3000

Protocol 3000 commands are a sequence of ASCII letters, structured according to the
following.

• Command format:

Prefix

Command Name

Constant (Space)

Parameter(s)

Suffix

#

Command



Parameter

<CR>

• Feedback format:

Prefix

Device ID

Constant

Command Name

Parameter(s)

Suffix

~

nn @ Command

Parameter

<CR><LF>

• Command parameters – Multiple parameters must be separated by a comma (,). In
addition, multiple parameters can be grouped as a single parameter using brackets ([
and ]).

• Command chain separator character – Multiple commands can be chained in the
same string. Each command is delimited by a pipe character (|).

• Parameters attributes – Parameters may contain multiple attributes. Attributes are
indicated with pointy brackets (<…>) and must be separated by a period (.).

The command framing varies according to how you interface with the VS-88UT. The following
figure displays how the # command is framed using terminal communication software (such
as Hercules):

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

49

Protocol 3000 Commands

Function

Description

Syntax

Parameters/Attributes

Example

#

Protocol handshaking.

Validates the
Protocol 3000
connection and gets
the machine number.

COMMAND

#<CR>

FEEDBACK

~nn@ok<CR><LF>

#<CR>

AUD

Set audio switch state.

When AFV
switching mode is
active, this command
also switches video
and unit replies with
command ~AV.

COMMAND

#AUDin>out_id,in>out_id,…<CR>

FEEDBACK

~nn@AUDin>out_id<CR><LF>

~nn@AUDin>out_id<CR><LF>

in – Input number or '0' to disconnect output
> – Connection character between in and out

parameters

out_id – Output number

1–34
* for all outputs

Switch embedded

audio HDMI™ IN 1

to HDMI OUT 3:

#AUD1>3<CR>

AUD?

Get audio switch
state.

When AFV
switching mode is
active, this command
also switches video
and unit replies with
command ~AV.

COMMAND

#AUD?out_id<CR>

#AUD?*<CR>

FEEDBACK

~nn@AUDin>out,in>out_id,…<CR><LF>

in – Input number or '0' to disconnect output
> – Connection character between in and out

parameters

out_id –Output number

1–34
* for all outputs

Get audio switch
state for output 1:

#AUD?1<CR>

AUD-LVL

Set volume level.

COMMAND

#AUD-LVLio_mode,io_index,vol_level<CR>

FEEDBACK

~nn@AUD-LVLio_mode,io_index,vol_level<CR><LF>

io_mode – Input/Output

0 – Input
1 – Output

io_index – Number that indicates the specific

input or output port:
1-34

vol_level – Volume level 0–70

Set AUDIO OUT 2
volume level to 50:

#AUD­LVL1,1,50<CR>

AUD-LVL?

Get volume level.

COMMAND

#AUD-LVL?io_mode,io_index<CR>

FEEDBACK

~nn@AUD-LVLio_mode,io_index,vol_level<CR><LF>

io_mode – Input/Output

0 – Input
1 – Output

io_index – Number that indicates the specific

input or output port:
1–34

vol_level – Volume level 0–70

Get AUDIO OUT 1
volume level

#AUD­LVL?1,1<CR>

AV

Switch audio and
video.

COMMAND

#AVin>out_id,in>out_id,…<CR>

FEEDBACK

~nn@AVin>out_id,in>out_id,…<CR><LF>

in – Number that indicates the specific input:

1–34
0 - disconnect output

> – Connection character between in and out

parameters

out_id – Output number

1–34
* for all outputs

Switch IN 1 to OUT
4:

#AV1>4<CR>

BALANCE

Set balance level.

COMMAND

#BALANCEout_index,balance_level<CR>

FEEDBACK

~nn@BALANCEout_index,balance_level<CR><LF>

out_index – Number that indicates the specific

output:

1–34

balance_level – Balance level

0–100
++ increase current value
– decrease current value

Set the speaker
output balance to
50:

#BALANCE1,50<

CR>

BALANCE?

Get balance level.

COMMAND

#BALANCE?io_index<CR>

FEEDBACK

~nn@BALANCEout_index,balance_level<CR><LF>

io_index – Number that indicates the specific

input or output port:

1–34

balance_level – Balance level

0–100

Get balance level
for Output 1:

#BALANCE?1<CR

>

BASS

Set audio bass level.

COMMAND

#BASSio_index,bass_level<CR>

FEEDBACK

~nn@BASSio_index,bass_level<CR><LF>

io_index – Number that indicates the specific

input or output port:

1–34

bass_level – Bass level

0–15
++ increase current value
– decrease current value

Set audio bass
level of channel 1
to 5:

#BASS1,5<CR>

BASS?

Get audio bass level.

COMMAND

#BASS?io_index<CR>

FEEDBACK

~nn@BASSio_index,bass_level<CR><LF>

io_index – Number that indicates the specific

input or output port:

1–34

bass_level – Bass level

0–15

Get audio bass
level of channel 1:

#BASS?1<CR>

BAUD

Set protocol serial port
baud rate.

The new defined
baud rate is stored in
the EEPROM and
used when powering
up.

Default baud rate is
115200 (on factory
reset).

Only works with
devices supporting
this command.

COMMAND

#BAUDbaud_rate<CR>

FEEDBACK

~nn@BAUDbaud_rate<CR><LF>

Option 1:

~nn@BAUDcurrent_baud_rate<CR><LF>

baud_rate –

9600, 19200, 38400, 57600, 115200

current_baud_rate –

9600, 19200, 38400, 57600, 115200, else -

current protocol serial port baud rate

baud_param – 0 - get the list of supported baud

rates

baud_rate1,baud_rate2, … – List of

supported baud rates

Set the baud rate to
9600:

#BAUD9600<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

50

Function

Description

Syntax

Parameters/Attributes

Example

BAUD?

Get protocol serial
port baud rate.
(Option 1 - for current
baud rate.
Option 2 - for list of
supported baud
rates).

The new defined
baud rate is stored in
the EEPROM and
used when powering
up.

Default baud rate is
115200 (on factory
reset).

Only works with
devices supporting
this command.

COMMAND

#BAUD?<CR>

#BAUD?baud_param<CR>

FEEDBACK

~nn@BAUDbaud_rate<CR><LF>

Option 1:

~nn@BAUDcurrent_baud_rate<CR><LF>

baud_rate –

9600, 19200, 38400, 57600, 115200

current_baud_rate –

9600, 19200, 38400, 57600, 115200, else -

current protocol serial port baud rate

baud_param – 0 - get the list of supported baud

rates

baud_rate1, – Baud_rate2, … - list of

supported baud rates

Get protocol serial
port baud rate:

#BAUD?<CR>

BRIGHTNESS

Set image brightness
per output.

Value limits can
vary for different
module cards.

Value is a property of
input connected to
current output.
Changing input source
might cause changes
in this value (refer
device definitions).

In devices that enable
showing multiple
outputs on one display
– each in a separate
window – this
command relates only
to the window
associated with the
output indicated in the
out-index parameter.

COMMAND

#BRIGHTNESSout_index,value<CR>

FEEDBACK

~nn@BRIGHTNESSout_index,value<CR><LF>

out_index – Number that indicates the specific

output:
1–34

value – Brightness value:

1–63

Set brightness for
output 1 to 50:

#BRIGHTNESS1,

50<CR>

BRIGHTNESS?

Get image brightness
per output.

Value limits can
vary for different
devices.

Value is a property of
input connected to
current output.
Changing input source
might cause changes
in this value (refer
device definitions).

In devices that enable
showing multiple
outputs on one display
– each in a separate
window – this
command relates only
to the window
associated with the
output indicated in the
out-index parameter.

COMMAND

#BRIGHTNESS?out_index<CR>

FEEDBACK

~nn@BRIGHTNESSout_index,value<CR><LF>

out_index – Number that indicates the specific

output:
1–34

value – Brightness value

Get brightness for
output 1:

#BRIGHTNESS?1

<CR>

BUILD-DATE?

Get device build date.

COMMAND

#BUILD-DATE?<CR>

FEEDBACK

~nn@BUILD-DATEdate,time<CR><LF>

date – Format: YYYY/MM/DD where

YYYY = Year
MM = Month
DD = Day

time – Format: hh:mm:ss where

hh = hours
mm = minutes
ss = seconds

Get the device
build date:

#BUILD-DATE?<C

R>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

51

Function

Description

Syntax

Parameters/Attributes

Example

CONTRAST

Set image contrast
per output.

Value limits can
vary for different
devices.

Value is a property of
input connected to
current output.
Changing the input
source might cause
changes in this value
(refer to device
definitions).

In devices that enable
showing multiple
outputs on one display
– each in a separate
window – this
command relates only
to the window
associated with the
output indicated in the
out-index parameter.

COMMAND

#CONTRASTout_index,value<CR>

FEEDBACK

~nn@CONTRASTout_index,value<CR><LF>

out_index – Number that indicates the specific

output:
1–34

value – Contrast value:

1–63

Set contrast for
Output 1 to 40:

#CONTRAST1,40

<CR>

CONTRAST?

Get image contrast
per output.

Value limits can
vary for different
devices.

Value is a property of
input connected to
current window.
Changing the window
input source might
cause changes in this
value (refer to device
definitions).

In devices that enable
showing multiple
outputs on one display
– each in a separate
window – this
command relates only
to the window
associated with the
output indicated in the
out-index parameter.

COMMAND

#CONTRAST?out_index<CR>

FEEDBACK

~nn@CONTRASTout_index,value<CR><LF>

out_index – Number that indicates the specific

output:
1–34

value – Contrast value

Get contrast for
Output 1:

#CONTRAST?1<C

R>

CPEDID

Copy EDID data from
the output to the input
EEPROM.

Destination bitmap
size depends on
device properties (for
64 inputs it is a 64-bit
word).

Example: bitmap
0x0013 means inputs
1,2 and 5 are loaded
with the new EDID.

In certain products
Safe_mode is an
optional parameter.
See the HELP
command for its
availability.

COMMAND

#CPEDIDedid_io,src_id,edid_io,dest_bitmap<CR>

or

#CPEDIDedid_io,src_id,edid_io,dest_bitmap,saf

e_mode<CR>

FEEDBACK

~nn@CPEDIDedid_io,src_id,edid_io,dest_bitmap<

CR><LF>

~nn@CPEDIDedid_io,src_id,edid_io,dest_bitmap,

safe_mode<CR><LF>

edid_io – EDID source type (usually output)

0 – Input
1 – Output
2 – Default EDID

src_id – Port ID number of chosen input or

output source

1–34
0 – Default EDID source

edid_io – EDID destination type (always input)

0 – Input

dest_bitmap – Bitmap representing destination

IDs. Format: XXXX…X, where X is hex digit. The

binary form of every hex digit represents
corresponding destinations.

0 – indicates that EDID data is not copied to

this destination.

1 – indicates that EDID data is copied to this

destination.

safe_mode – Safe mode

0 – device accepts the EDID as is without

trying to adjust

1 – device tries to adjust the EDID (default

value if no parameter is sent)

Copy the EDID
data from the
Output 1 (EDID
source) to the
Input:

#CPEDID1,1,0,

0x1<CR>

Copy the EDID
data from the
default EDID
source to the Input:

#CPEDID2,0,0,

0x1<CR>

DETAIL­TIMING?

Get detail timing
parameters.

COMMAND

#DETAIL-TIMING?param,in_index<CR>

FEEDBACK

~nn@DETAIL-TIMINGparam,in_index,value<CR><LF>

param – Detail Timing

2 – H-De-Total
5 – V-De-Total

in_index – Number that indicates the specific

input:
1–34

value – Video parameter in Kramer units, minus

sign precedes negative values

Get detail timing
parameters:

#@DETAIL-TIMIN
G?2,1<CR>

DISPLAY?

Get output HPD
status.

After execution,
response is sent to
the com port from
which the command
was received.
Response is sent after
every change in
output HPD status ON
to OFF.
Response is sent after
every change in
output HDP status
OFF to ON.

COMMAND

#DISPLAY?out_index<CR>

FEEDBACK

~nn@DISPLAYout_index,status<CR><LF>

out_index – Number that indicates the specific

output:
1–34

status – HPD status according to signal

validation

0 – HPD ON to OFF,
1 – HPD OFF to ON,
2 - EDID ready

Get the output HPD
status of Output 1:

#DISPLAY?1<CR

>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

52

Function

Description

Syntax

Parameters/Attributes

Example

EQ-LVL

Set equalization level.

COMMAND

#EQ-LVLio_mode,io_index,eq_type,eq_level<CR>

FEEDBACK

~nn@EQ-LVLio_mode,io_index,eq_type,eq_level<C

R><LF>

io_mode – Input/Output

0 – Input
1 – Output

io_index – Number that indicates the specific

input or output port:
1–34

eq_type – Equalizer Types

0 – Bass
2 – Treble

eq_level – Equalizer level:

0–15

Set Bass EQ level
of the speaker
output to 12:

#EQ­LVL1,1,0,12<C

R>

EQ-LVL?

Get equalization level.

COMMAND

#EQ-LVL?io_mode,io_index,eq_type<CR>

FEEDBACK

~nn@EQ-LVLio_mode,io_index,eq_type,eq_level<C

R><LF>

io_mode – Input/Output

0 – Input
1 – Output

io_index – Number that indicates the specific

input or output port:
1–34

eq_type – Equalizer Types

0 – Bass
2 – Treble

eq_level – Equalizer level:

0–15

Get Bass EQ level
of the speaker
output to 12:

#EQ­LVL?1,2,2<CR>

ETH-PORT

Set Ethernet port
protocol.

If the port number
you enter is already in
use, an error is
returned.
The port number must
be within the following
range: 0-(2^16-1).

COMMAND

#ETH-PORTport_type,port_id<CR>

FEEDBACK

~nn@ETH-PORTport_type,port_id<CR><LF>

port_type – TCP/UDP
port_id – TCP/UDP port number:

1 – 65535

Set the Ethernet
port protocol for
TCP to port 12457:

#ETH-PORT0,12

457<CR>

ETH-PORT?

Get Ethernet port
protocol.

COMMAND

#ETH-PORT?port_type<CR>

FEEDBACK

~nn@ETH-PORTport_type,port_id<CR><LF>

port_type – TCP/UDP
port_id – TCP / UDP port number:

1 – 65535

Get the Ethernet
port protocol for
UDP:

#ETH-PORT?TCP

<CR>

EXT-CFG­FILE?

Get configuration file
status.

COMMAND

#EXT-CFG-FILE?<CR>

FEEDBACK

~nn@EXT-CFG-FILEstatus<CR><LF>

status –

0 – configuration.json is not ready
1 – configuration.json is ready
2 – updating matrix via configuration file

Get the
configuration file
status:

#EXT-CFG­FILE?<CR>

EXT-ETH-PORT

Set Ethernet port
number for a specific
module card.

If the module card
does not support
Ethernet functions,
ERR 034 is returned.

COMMAND

#EXT-ETH-PORTport_type,slot_id,port_id<CR>

FEEDBACK

~nn@EXT-ETH­PORTport_type,slot_id,port_id<CR><LF>

port_type – TCP/UDP
slot_id – Module ID (slot number):

0 or 100 – control module
1–17

port_id – TCP/UDP port number:

1 – 65535

Set the Ethernet
TCP port number
for the card in slot 1
to 12457:

#EXT-ETH­PORTTCP,1,124

57<CR>

EXT-ETH­PORT?

Get Ethernet port
number for a specific
module card.

If the module card
does not support
Ethernet functions,
ERR 034 is returned.

COMMAND

#EXT-ETH-PORT?port_type,slot_id<CR>

FEEDBACK

~nn@EXT-ETH­PORT?port_type,slot_id,port_id<CR><LF>

port_type – TCP/UDP
slot_id – Module ID (slot number):

0 or 100 – control module
1–17

port_id – TCP/UDP port number:

1 – 65535

Get the Ethernet
TCP port number
for the card in slot
1:

#EXT-ETH­PORT?TCP,1<CR

>

EXT-FAN­LEVEL

Set fan operation
speed and mode.

COMMAND

#EXT-FAN­LEVELfan_index,fan_speed,fan_mode<CR>

FEEDBACK

~nn@EXT-FAN­LEVELfan_index,fan_speed,fan_mode,fan_status<

CR><LF>

fan_index – number that indicates the fan

being set:

1–8 – Chassis fans

fan_speed –

0–4

fan_mode –

0 – Fan operation automatically controlled

based on the device temperature

1 – Continuous operation

The default is automatic. If a fan is set to

continuous and the device is reset, the fan
returns to automatic.

fan_status –

OK
WARN

Set fan #1 speed to
2 and mode to
continuous:

#EXT-FAN­LEVEL1,2,1<CR

>

EXT-INFO-IO?

Get a list of ports
according to signal
type (video or audio)
and direction (inputs
or outputs).

COMMAND

#EXT-INFO-IO?signal_type,io_mode<CR>

FEEDBACK

~nn@Devicesignal_type,io_mode,io_index,io_ind

ex,io_index,...<CR><LF>

signal_type–

1 – video
2 – audio

io_mode – Input/Output

0 – Input
1 – Output

io_index – Number that indicates the specific

input or output port:

1–34

Get the list of video
input ports:

#EXT-INFO­IO?1,0<CR>

EXT-NET-MAC?

Get the MAC address
for a module card.

COMMAND

#EXT-NET-MAC?slot_id<CR>

FEEDBACK

~nn@EXT-NET-MAC?slot_id,mac_address<CR><LF>

slot_id – Module ID (slot number):

0 or 100 – control module
1–17

mac_address – Unique MAC address. Format:

XX-XX-XX-XX-XX-XX (where X is a hex digit)

Get the MAC
address for the
card in slot 1:

#EXT-NET­MAC?1<CR>

EXT-PING

Ping the IP address.

COMMAND

#EXT-PINGip_address<CR>

FEEDBACK

~nn@EXT-PINGping_information<CR><LF>

ip_address – Format: xxx.xxx.xxx.xxx

Get the gateway IP
address:

#EXT­PING192.168.1

.39<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

53

Function

Description

Syntax

Parameters/Attributes

Example

EXT-POE

Enable/disable the
+48V input for the PS­4812 PoE power
supply add-on.

Only the input for
the PS-4812 PoE
power supply add-on
can be
enabled/disabled. The
module card ports do
not.

COMMAND

#EXT-POE0,enable_value<CR>

FEEDBACK

~nn@EXT-POE0,enable_value,48V_status<CR><LF>

port_id –

0 – 48V input connector

enable_value –

ON – 48V input is enabled
OFF – 48V input is disabled

48v_status – Operational status of 48V input:

OK – Receiving power
WARN – Not working
POWERDOWN – Enabled, but receiving

power

Enable the 48V
input for the PS­4812 PoE power
supply add-on:

#EXT­POE0,ON<CR>

EXT-POE?

Get the PoE power
operational status for
one of the module
card ports or for the
+48V input for the
PS-4812 PoE power
supply add-on.

COMMAND

#EXT-POE?port_id<CR>

FEEDBACK

~nn@EXT-POE?0,enable_value,48V_status<CR><LF>

port_id –

0 – 48V connector
1–34

enable_value –

ON – 48V input is enabled
OFF – 48V input is disabled

48v_status – Operational status of 48V input:

OK – Receiving power
WARN – Not working
POWERDOWN – Disabled, but receiving

power

Get the
enable/disable
status of the 48V
input for port 2:

#EXT­POE?2<CR>

EXT-PSU?

Get the status of the
power supply unit.

COMMAND

#EXT-PSU?ps_id<CR>

FEEDBACK

~nn@EXT­PSUps_id,plug_status,ps_status<CR><LF>

ps_id – Power supply id number:

1–2
* – both PSUs

plug_status – Physical connection status of

the power supply:

ON – Connected
OFF – Disconnected

ps_status – Power status of the power supply:

OK – powered properly
WARN – not powered properly and may need

to be checked

OFFLINE – not receiving power

Get the status of
power supply 1:

#EXT­PSU?1<CR>

EXT-PSU­BUZZER

Enable/disable PSU
warning buzzer.

COMMAND

#EXT-PSU-BUZZERenabled_status<CR>

FEEDBACK

~nn@EXT-PSU-BUZZERenabled_status<CR><LF>

enabled_status –

0 – Disable
1 – Enable

Enable the PSU
warning buzzer:

#EXT-PSU­BUZZER1<CR>

EXT-PSU­BUZZER?

Get the enable/disable
status of the PSU
warning buzzer.

COMMAND

#EXT-PSU-BUZZER?<CR>

FEEDBACK

~nn@EXT-PSU-BUZZER?enabled_status<CR><LF>

enabled_status –

0 – Disabled
1 – Enabled

Get the
enable/disable
status of the PSU
warning buzzer:

#EXT-PSU­BUZZER?<CR>

EXT-VOLT?

Get the voltage of the
board.

COMMAND

#EXT-VOLT?slot_id<CR>

FEEDBACK

~nn@EXT-VOLT?slot_id：

volt_checkpoint_id/volt_checkpoint_total :
stdand value：actual value：status<CR><LF>

slot_id – Module ID (slot number):

1–17

volt_checkpoint_id – ID number of current

voltage detection point, starting from 1

volt_checkpoint_total – Nnumber of

voltage detection points

stdand value – Hardware design value
actual value – Current value
status –

WARN
OK

Get the voltage for
the card in slot 1:

#EXT­VOLT?slot_id<

CR>

FACTORY

Reset device to
factory default
configuration.

This command
deletes all user data
from the device. The
deletion can take
some time.

Your device may
require powering off
and powering on for
the changes to take
effect.

COMMAND

#FACTORY<CR>

FEEDBACK

~nn@FACTORYok<CR><LF>

Reset the device to
factory default
configuration:

#FACTORY<CR>

FPGA-VER?

Get current FPGA
version.

COMMAND

#FPGA-VER?fpga_id<CR>

FEEDBACK

~nn@FPGA-VERfpga_id,expected_ver,ver<CR><LF>

fpga_id – FPGA id
expected_ver – Expected FPGA version for

current firmware

ver – Actual FPGA version

Get current FPGA
version:

#FPGA­VER?1<CR>

GEDID

Get EDID support on
certain input/output.

For old devices
that do not support
this command,
~nn@ERR
002<CR><LF> is
received.

COMMAND

#GEDIDio_mode,in_index<CR>

FEEDBACK

~nn@GEDIDio_mode,in_index,size<CR><LF>

io_mode – Input/Output

0 – Input
1 – Output
2 – Default EDID

io_index – Number that indicates the specific

input or output port:

1–34

size – Size of data to be sent from device, 0

means no EDID support

Get EDID support
information for
input 1:

#GEDID 1<CR>

GET

Get file contents.

COMMAND

#GETfile_name<CR>

FEEDBACK

Multi-line:

~nn@GETfile_name,file_sizeready<CR><LF>

contents

~nn@GETfile_nameok<CR><LF>

file_name – Name of file from which to get

contents, includes:
CONFIGURATION.JSON
CONFIG_LOG.JSON
METADATA.JSON, MESSAGES

contents – Byte stream of file contents
file_size – Size of file (device sends it in

response to give user a chance to get ready)

#GETfile_resp
onse.dat<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

54

Function

Description

Syntax

Parameters/Attributes

Example

HDCP-MOD

Set HDCP mode.

Set HDCP working
mode on the device
input:

HDCP supported ­HDCP_ON [default].

HDCP not supported ­HDCP OFF.

HDCP support
changes following
detected sink ­MIRROR OUTPUT.

COMMAND

#HDCP-MODin_index,mode<CR>

FEEDBACK

~nn@HDCP-MODin_index,mode<CR><LF>

in_index – Number that indicates the specific

input:
1–34

mode – HDCP mode:

0 – HDCP Off
1 – HDCP On

Set the input
HDCP-MODE of IN
1 to Off:

#HDCP­MOD1,0<CR>

HDCP-MOD?

Get HDCP mode.

Set HDCP working
mode on the device
input:

HDCP supported ­HDCP_ON [default].

HDCP not supported ­HDCP OFF.

HDCP support
changes following
detected sink ­MIRROR OUTPUT.

COMMAND

#HDCP-MOD?in_index<CR>

FEEDBACK

~nn@HDCP-MODin_index,mode<CR><LF>

in_index – Number that indicates the specific

input:
1–34

mode – HDCP mode:

0 – HDCP Off
3 – HDCP defined according to the connected

output

Get the input
HDCP-MODE of IN
1 HDMI:

#HDCP-MOD?1<C

R>

HDCP-STAT?

Get HDCP signal
status.

io_mode =1 – get
the HDCP signal
status of the sink
device connected to
the specified output.

io_mode =0 – get the
HDCP signal status of
the source device
connected to the
specified input.

COMMAND

#HDCP-STAT?io_mode,in_index<CR>

FEEDBACK

~nn@HDCP-STATio_mode,in_index,status<CR><LF>

io_mode – Input/Output

0 – Input
1 – Output

in_index – Number that indicates the specific

input:
1–34

status – Signal encryption status - valid values

On/Off

0 – HDCP Off
1 – HDCP On

Get the output
HDCP-STATUS of
IN 1:

#HDCP­STAT?0,1<CR>

HELP

Get command list or
help for specific
command.

COMMAND

#HELP<CR>

#HELPcmd_name<CR>

FEEDBACK

1. Multi-line:

~nn@Devicecmd_name,cmd_name…<CR><LF>

To get help for command use: HELP
(COMMAND_NAME)<CR><LF>

~nn@HELPcmd_name:<CR><LF>

description<CR><LF>

USAGE:usage<CR><LF>

cmd_name – Name of a specific command

Get the command
list:

#HELP<CR>

To get help for
HDCP-MOD:
HELPhdcp-

modCR>

H-PHASE

Set H-phase.

COMMAND

#H-PHASEio_mode,io_index,value<CR>

FEEDBACK

~nn@H-PHASEio_mode,io_index,value<CR><LF>

io_mode – Input/Output

1 – Input
2 – Output

io_index – Number that indicates the specific

input or output port:

1–34

value – Video parameter in Kramer units:

0–63
++ increase current value
– decrease current value

Set H-phase:

#H-PHASE1,1,1

<CR>

H-PHASE?

Get H-phase.

COMMAND

#H-PHASE?io_mode,io_index<CR>

FEEDBACK

~nn@H-PHASEio_mode,io_index,value<CR><LF>

io_mode – Input/Output

1 – Input
2 – Output

io_index – Number that indicates the specific

input or output port:
1–34

value – Video parameter in Kramer units, minus

sign precedes negative values

Get H-phase:

#H-PHASE?1,1<

CR>

HW-TEMP?

Get temperature of a
specific region of the
hardware.

The Get command
is not available for all
parts of the hardware,
and is device specific.

COMMAND

#HW-TEMP?region_id<CR>

FEEDBACK

~nn@HW-TEMPregion_id,temperature<CR><LF>

region_id – ID of the region for which to get

the temperature

0 – Control Board
1–17 – Module card slot number
* – Matrix

temperature – Temperature in Celsius of the

HW region, rounded down to the closest integer

Get temperature of
a specific region of
the hardware:

#HW-TEMP?1<CR

>

INFO-IO?

Get in/out count.

COMMAND

#INFO-IO?<CR>

FEEDBACK

~nn@INFO-IOINin_count,OUTout_count<CR><LF>

in_count – Number of inputs in the unit
out_count – Number of outputs in the unit

Get inputs count:

#INFO-IO?<CR>

INFO-PRST?

Get maximum preset
count.

In most units,
video and audio
presets with the same
number are stored
and recalled together
by commands
#PRST-STO and
#PRST-RCL.

COMMAND

#INFO-PRST?<CR>

FEEDBACK

~nn@INFO-PRSTvidvideo_preset_count,audaudio

_preset_count<CR><LF>

video_preset_count – Maximum number of

video presets in the unit

audio_preset_count – Maximum number of

audio presets in the unit

Get number of
video and audio
presets:

#INFO­PRST?<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

55

Function

Description

Syntax

Parameters/Attributes

Example

LDEDID

Write EDID data from
external application to
device.

When the unit
receives the LDEDID
command it replies
with READY and
enters the special
EDID packet wait
mode. In this mode
the unit can receive
only packets and not
regular protocol
commands.

If the unit does not
receive correct
packets for 30
seconds or is
interrupted for more
than 30 seconds
before receiving all
packets, it sends
timeout error

~nn@LDEDIDerr01

<CR><LF> and

returns to the regular
protocol mode. If the
unit received data that
is not a correct
packet, it sends the
corresponding error
and returns to the
regular protocol mode.

COMMAND

Multi-step syntax

FEEDBACK

Step 1:

#LDEDIDedid_io,dest_bitmask,edid_size,safe_mo

de<CR>

Response 1:

~nn@LDEDIDedid_io,dest_bitmask,edid_size,safe

_modeready<CR><LF>

or

~nn@LDEDIDerrnn<CR><LF>

Step 2: If ready was received, send EDID_DATA
Response 2:

~nn@LDEDIDedid_io,dest_bitmask,edid_size,safe

_modeok<CR><LF>

or

~nn@LDEDIDerrnn<CR><LF>

edid_io – EDID destination type (always input)

0 – Input

dest_bitmask – Bitmap representing

destination IDs. Format: 0x********, where * is
ASCII presentation of hex digit. The binary
presentation of this number is a bit mask for

destinations. Setting ‘1’ means EDID data has to

be copied to this destination

edid_size – EDID data size
safe_mode – Safe mode

0 – Device accepts the EDID as is without

trying to adjust

1 – Device tries to adjust the EDID

edid_data – Data in protocol packets

Using the Packet Protocol

Send a command: LDRV, LOAD, IROUT,

LDEDID
Receive Ready or ERR###
If Ready:

a. Send a packet,

b. Receive OK on the last packet,

c. Receive OK for the command

Packet structure:

Packet ID (1, 2, 3…) (2 bytes in length)

Length (data length + 2 for CRC) – (2

bytes in length)

Data (data length -2 bytes)

CRC – 2 bytes

01

02

03

04

05 Packet ID

Length

Data

CRC

5. Response: ~nnnnok<CR><LF> (Where

NNNN is the received packet ID in ASCII

hex digits.)

Write the EDID
data from an
external application
to the HDMI In 1
input without
adjustment
attempts:

#LDEDID0,0x1,
2340,0<CR>

Write the EDID
data from an
external application
to HDMI In 1 and
PC In inputs with
adjustment
attempts:

#LDEDID0,0x5,
2340,1<CR>

LOAD

Load file to device.

COMMAND

#LOADfile_name,size<CR>

FEEDBACK

Data sending negotiation:
* Device -

~01@LOADfile_name,sizeready<CR><LF>

* End User (+Device)­Send file in Protocol Packets
* Device -

~01@LOADfile_name,sizeok<CR><LF>

file_name – Name of file to save on device
size – Size of file data that is sent

Using the Packet Protocol

Send a command: LDRV, LOAD, IROUT,

LDEDID
Receive Ready or ERR###
If Ready:

a. Send a packet,

b. Receive OK on the last packet,

c. Receive OK for the command

Packet structure:

Packet ID (1, 2, 3…) (2 bytes in length)

Length (data length + 2 for CRC) – (2

bytes in length)

Data (data length -2 bytes)

CRC – 2 bytes

01

02

03

04

05 Packet ID

Length

Data

CRC

Response: ~nnnnok<CR><LF> (Where

NNNN is the received packet ID in ASCII

hex digits.)

Load the
file_response.dat
file to the device:

#LOADfile_res
ponse.dat,5360

<CR>

LOAD

Load file to device.

COMMAND

#LOADfile_name,size<CR>

FEEDBACK

Data sending negotiation:
* Device -

~01@LOADfile_name,sizeready<CR><LF>

* End User (+Device)­Send file in Protocol Packets
* Device –
~01@LOADfile_name,sizeok<CR><LF>

file_name – Name of file to save on device
size – Size of file data that is sent

Load the
file_response.dat
file to the device:
#LOADfile_respon
se.dat,5360<CR>

LOCK-FP

Lock the front panel.

COMMAND

#LOCK-FPlock/unlock<CR>

FEEDBACK

~nn@LOCK-FPlock/unlock<CR><LF>

lock/unlock – On/Off

0 – unlock front panel
1 – lock front panel

Unlock front panel:

#LOCK-FP0<CR>

LOCK-FP?

Get the front panel
lock state.

In NT-52N, this
command includes the
PortNumber (1-2)
parameter.

COMMAND

#LOCK-FP?<CR>

FEEDBACK

~nn@LOCK-FPlock/unlock<CR><LF>

lock/unlock – On/Off

0 – unlock front panel
1 – lock front panel

Get the front panel
lock state:

#LOCK-FP?<CR>

MIX

Set audio MIX.

COMMAND

#MIXout_index,mix_mode<CR>

FEEDBACK

~nn@MIXout_index,mix_mode<CR><LF>

out_index – Number that indicates the specific

output:

1–34

mix_mode – On/Off

0 – Off
1 – On

Set audio MIX:

#MIX1,1<CR>

MIX?

Get audio MIX.

COMMAND

#MIX?out_index<CR>

FEEDBACK

~nn@MIXout_index,mix_mode<CR><LF>

out_index – Number that indicates the specific

output:

1–34

mix_mode – On/Off

0 – Off
1 – On

Get audio MIX for
output 1:

#MIX?1<CR>

MODEL?

Get device model.

COMMAND

#MODEL?<CR>

FEEDBACK

~nn@MODELmodel_name<CR><LF>

model_name – String of up to 19 printable ASCII

chars

Get the device
model:

#MODEL?<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

56

Function

Description

Syntax

Parameters/Attributes

Example

MODULE-INFO?

Get module
information.

COMMAND

#MODULE-INFO?slot_id<CR>

FEEDBACK

~nn@MODULE-INFOslot_id,m_direction,channel_st

art,channel_end,mod_type,fw_ver,upgradable,mod
_status<CR><LF>

slot_id – Module ID (slot number):

0 – control module
1–17 – I/O cards
200 – test module
201 – keyboard software application
202 – keyboard hardware

m_direction – Transmission direction

0 – input
1 – output
2 – OS system or applications in the control

board or unknown

channel_start – Start ID of the port in the

device

1–34

channel_end – End ID of the port in the device

1–34

mod_type – Module type

18 – VGAA
32 – SDIA
47 – Control module
49 – H2
50 – H2A
57 – DTAxrC2
59 – DTxrD2
203 – Sub-function for control board.
204 – InnerEthSwitcher in the matrix
205 – Power and fan monitor in the matrix
206 – Main board in the matrix

fw_ver – Module firmware version

XX.XX.XXXX where the digit groups are:
major.minor.build version

upgradable – Indicates whether the firmware

can be upgraded

0 – not upgradable
1 – upgradable

mod_status – Module status

0 – OK
1 – unknown error
2 – no communication
3 – module missing or offline

Get information for
the module in slot
8:

#MODULE-INFO?
8<CR>

MODULE-TYPE?

Get module type.

COMMAND

#MODULE-TYPE?module_id<CR>

FEEDBACK

~nn@MODULE-TYPEmodule_id,mod_type,mod_status<

CR><LF>

module_id – Number that identifies the module

1–17

mod_type – Module type

18 – VGAA
32 – SDIA
47 – Control module
49 – H2
50 – H2A
57 – DTAxrC2
59 – DTxrD2

mod_status – Module status

0 – OK
1 – Unknown error
2 – No communication
3 – Module missing or offline

Get module type:

#MODULE-TYPE?

1<CR>

MODULE-VER?

Get module version.

Some devices do
not set the new
machine number until
the device is
restarted.

Some devices can
change the machine
number only from
DIP-switches.

COMMAND

#MODULE-VER?module_id<CR>

FEEDBACK

~nn@MODULE-VERmodule_id,fw_version<CR><LF>

module_id – Number that identifies the module

0 – control module
1–17 – I/O cards
220 – Linux OS

fw_version – XX.XX.XXXX where the digit

groups are: major.minor.build version

Get module
version:

#MODULE-VER?1

<CR>

MUTE

Set audio mute.

COMMAND

#MUTEout_index,mute_mode<CR>

FEEDBACK

~nn@MUTEout_index,mute_mode<CR><LF>

out_index – Number that indicates the specific

output:
1–34

mute_mode – On/Off

0 – Off
1 – On

Set Output 1 to
mute:

#MUTE1,1<CR>

MUTE?

Get audio mute.

COMMAND

#MUTE?out_index<CR>

FEEDBACK

~nn@MUTEout_index,mute_mode<CR><LF>

out_index – Number that indicates the specific

output:
1–34

mute_mode – On/Off

0 – Off
1 – On

Get mute status of
output 1

#MUTE?1<CR>

NAME

Set machine (DNS)
name.

The machine
name is not the same
as the model name.
The machine name is
used to identify a
specific machine or a
network in use (with
DNS feature on).

COMMAND

#NAMEmachine_name<CR>

FEEDBACK

~nn@NAMEmachine_name<CR><LF>

machine_name – String of up to 15 alpha-

numeric chars (can include hyphen, not at the
beginning or end)

Set the DNS name
of the device to
room-442:

#NAMEroom-

442<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

57

Function

Description

Syntax

Parameters/Attributes

Example

NAME?

Get machine (DNS)
name.

The machine
name is not the same
as the model name.
The machine name is
used to identify a
specific machine or a
network in use (with
DNS feature on).

COMMAND

#NAME?<CR>

FEEDBACK

~nn@NAMEmachine_name<CR><LF>

machine_name – String of up to 15 alpha-

numeric chars (can include hyphen, not at the
beginning or end)

Get the DNS name
of the device:

#NAME?<CR>

NAME-RST

Reset machine (DNS)
name to factory
default.

Factory default of
machine (DNS) name

is “KRAMER_” + 4

last digits of device
serial number.

COMMAND

#NAME-RST<CR>

FEEDBACK

~nn@NAME-RSTok<CR><LF>

Reset the machine
name (S/N last
digits are 0102):

#NAME­RSTkramer_010

2<CR>

NET-CONFIG

Set a network
configuration.

If the gateway
address is not
compliant to the
subnet mask used for
the host IP, the
command returns an
error. Subnet and
gateway compliancy
specified by RFC950.

COMMAND

#NET-CONFIGnetw_id,net_ip,net_mask,gateway<CR

>

FEEDBACK

~nn@NET-CONFIGnetw_id,net_ip,net_mask,gateway

<CR><LF>

netw_id – Network ID–the device network

interface

0 or 100 – control module
1–17 – module cards

net_ip – Network IP
net_mask – Network mask
gateway – Network gateway

Set the device
network
parameters to IP
address

192.168.113.10,
net mask

255.255.0.0, and
gateway

192.168.0.1:

#NET-CONFIG0,

192.168.113.10

,255.255.0.0,1

92.168.0.1<CR>

NET-CONFIG?

Get a network
configuration.

COMMAND

#NET-CONFIG?netw_id<CR>

FEEDBACK

~nn@NET-CONFIGnetw_id,net_ip,net_mask,gateway

<CR><LF>

netw_id – Network ID–the device network

interface

0 or 100 – control module
1–17 – module cards

net_ip – Network IP
net_mask – Network mask
gateway – Network gateway

Get network
configuration for
the module card in
slot 2:

#NET-CONFIG?2

<CR>

NET-DHCP

Set DHCP mode.

Only 1 is relevant
for the mode value. To
disable DHCP, the
user must configure a
static IP address for
the device.

Connecting Ethernet
to devices with DHCP
may take more time in
some networks.

To connect with a
randomly assigned IP
by DHCP, specify the
device DNS name (if
available) using the
NAME command. You
can also get an
assigned IP by direct
connection to USB or
RS-232 protocol port,
if available.

For proper settings
consult your network
administrator.

COMMAND

#NET-DHCPdhcp_state<CR>

FEEDBACK

~nn@NET-DHCPdhcp_state<CR><LF>

dhcp_state –

0 – Do not use DHCP. Use the IP set by the

factory or using the NET-CONFIG or NET-
IP command.

1 – Try to use DHCP. If unavailable, use the IP

address set by the factory or the NET-
CONFIG or NET-IP command.

Enable DHCP
mode for port 1, if
available:

#NET­DHCP1,1<CR>

NET-DHCP?

Get DHCP mode.

COMMAND

#NET-DHCP?<CR>

FEEDBACK

~nn@NET-DHCPdhcp_mode<CR><LF>

dhcp_mode –

0 – Do not use DHCP. Use the IP set by the

factory or using the NET-CONFIG or NET-
IP command.

1 – Try to use DHCP. If unavailable, use the IP

set by the factory or using the NET-
CONFIG or NET-IP command.

Get DHCP mode
for port 1:

#NET-DHCP?1<C

R>

NET-GATE

Set gateway IP.

A network gateway
connects the device
via another network
and maybe over the
Internet. Be careful of
security issues. For
proper settings
consult your network
administrator.

COMMAND

#NET-GATEip_address<CR>

FEEDBACK

~nn@NET-GATEip_address<CR><LF>

ip_address – Format: xxx.xxx.xxx.xxx

Set the gateway IP
address to

192.168.0.1:

#NET­GATE192.168.0

00.001<CR>

NET-GATE?

Get gateway IP.

A network gateway
connects the device
via another network
and maybe over the
Internet. Be careful of
security issues. For
proper settings
consult your network
administrator.

COMMAND

#NET-GATE?<CR>

FEEDBACK

~nn@NET-GATEip_address<CR><LF>

ip_address – Format: xxx.xxx.xxx.xxx

Get the gateway IP
address:

#NET-GATE?<CR

>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

58

Function

Description

Syntax

Parameters/Attributes

Example

NET-IP

Set IP address.

For proper settings
consult your network
administrator.

COMMAND

#NET-IPip_address<CR>

FEEDBACK

~nn@NET-IPip_address<CR><LF>

ip_address – Format: xxx.xxx.xxx.xxx

Set the IP address
to 192.168.1.39:

#NET­IP192.168.001
.039<CR>

NET-IP?

Get IP address.

COMMAND

#NET-IP?<CR>

FEEDBACK

~nn@NET-IPip_address<CR><LF>

ip_address – Format: xxx.xxx.xxx.xxx

Get the IP address:

#NET-IP?<CR>

NET-MAC?

Get MAC address.

COMMAND

#NET-MAC?<CR>

FEEDBACK

~nn@NET-MACmac_address<CR><LF>

mac_address – Unique MAC address. Format:

XX-XX-XX-XX-XX-XX where X is hex digit

#NET­MAC?id<CR>

NET-MASK

Set subnet mask.

For proper settings
consult your network
administrator.

COMMAND

#NET-MASKnet_mask<CR>

FEEDBACK

~nn@NET-MASKnet_mask<CR><LF>

net_mask – Format: xxx.xxx.xxx.xxx

Set the subnet
mask to

255.255.0.0:

#NET­MASK255.255.0

00.000<CR>

NET-MASK?

Get subnet mask.

COMMAND

#NET-MASK?<CR>

FEEDBACK

~nn@NET-MASKnet_mask<CR><LF>

net_mask – Format: xxx.xxx.xxx.xxx

Get the subnet
mask:

#NET-MASK?<CR>

PORT­DIRECTION?

Get port direction for
video port.

This command
gets the direction of a
bidirectional port.

COMMAND

#PORT-DIRECTION?port_index<CR>

FEEDBACK

~nn@PORT-DIRECTIONport_index,direction<CR><LF

>

port_index – Port number

1–34

direction –

0 – Input
1– Output

Get port direction
for port 2:

#PORT­DIRECTION?5<C

R>

PROT-VER?

Get device protocol
version.

COMMAND

#PROT-VER?<CR>

FEEDBACK

~nn@PROT-VER3000:version<CR><LF>

version – XX.XX where X is a decimal digit

Get the device
protocol version:

#PROT-VER?<CR

>

PRST-AUD?

Get audio connections
from saved preset.

Video and audio
presets with the same
number are stored
and recalled together
by commands
#PRST-STO and
#PRST-RCL.

COMMAND

#PRST-AUD?preset,out_index<CR>

#PRST-AUD?preset,*<CR>

FEEDBACK

~@PRST-AUDpreset,in_index>out_index<CR><LF>

~@PRST-AUDpreset,in_index>1,in_index>2,in_ind

ex>3,…<CR><LF>

preset – Preset number
in_index – Number that indicates the specific

input:

1 – N (N= the total number of inputs)
0 – Output is disconnected

> – Connection character between in and out

parameters

out_index – Number that indicates the specific

output:

1 – 34
* – All outputs

Get audio
connection for OUT
3 from saved
preset 1:

#PRST­AUD?1,3<CR>

PRST-LST?

Get saved preset list.

Video and audio
presets with the same
number are stored
and recalled together
by commands

#PRST-STO and
#PRST-RCL.

COMMAND

#PRST-LST?<CR>

FEEDBACK

~nn@PRST-LSTpreset,preset,…<CR><LF>

preset – Preset number

Show preset list:

#PRST-LST?<CR>

PRST-RCL

Recall saved preset
list.

Video and audio
presets with the same
number are stored
and recalled together
by commands

#PRST-STO and
#PRST-RCL.

COMMAND

#PRST-RCLpreset<CR>

FEEDBACK

~nn@PRST-RCLpreset<CR><LF>

preset – Preset number

Recall preset 1:

#PRST­RCL1<CR>

PRST-STO

Store current
connections, volumes,
and modes in preset.

Video and audio
presets with the same
number are stored
and recalled together
by commands

#PRST-STO and
#PRST-RCL.

COMMAND

#PRST-STOpreset<CR>

FEEDBACK

~nn@PRST-STOpreset<CR><LF>

preset – Preset number

Store the current
configuration under
preset 1:

#PRST­STO1<CR>

PRST-VID?

Get video connections
from saved preset.

In most units,
video and audio
presets with the same
number are stored
and recalled together
by commands

#PRST-STO and
#PRST-RCL.

COMMAND

#PRST-VID?preset,out_index<CR>

#PRST-VID?preset,*<CR>

FEEDBACK

~nn@PRST-VIDpreset,in_index>out_index<CR><LF>

~nn@PRST-VIDpreset,in_index>1,in_index>2,in_i

ndex>3,…<CR><LF>

preset – Preset number
in_index – Number that indicates the specific

input:

1 – 34
0 – Output is disconnected

> – Connection character between in and out

parameters

out_index – Output number

1–34
* for all outputs

Get video
connections from
preset 3 for all
outputs:

#PRST­VID?3,*<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

59

Function

Description

Syntax

Parameters/Attributes

Example

RESET

Reset device.

To avoid locking
the port due to a USB
bug in Windows,
disconnect USB
connections
immediately after
running this
command. If the port
was locked,
disconnect and
reconnect the cable to
reopen the port.

COMMAND

#RESET<CR>

FEEDBACK

~nn@RESETok<CR><LF>

Reset the device:

#RESET<CR>
ROUTE

Set layer routing.

This command
replaces all other
routing commands.

COMMAND

#ROUTElayer_type,out_index,in_index<CR>

FEEDBACK

~nn@ROUTElayer_type,out_index<CR><LF>

layer_type Layer Enumeration

1 – Video
2 – Audio

out_index – Number that indicates the specific

output

1–34
* for all outputs

in_index – Number that indicates the specific

input

0 – disconnect the output
1–34

Route HDMI IN 2 to
HDMI OUT 4:

#ROUTE1,2,4<C

R>

ROUTE?

Get layer routing.

This command
replaces all other
routing commands.

COMMAND

#ROUTE?layer_type,out_index<CR>

FEEDBACK

~nn@ROUTElayer_type,out_index,in_index<CR><LF

>

layer_type Number that represents the type of

signal

1 – Video
2 – Audio

out_index – Number that indicates the specific

output

1–34
* for all outputs

in_index – Number that indicates the specific

input

0 – output is disconnected
1–34

Get the video
routing for output 2:

#ROUTE?1,2<CR

>

SIGNAL?

Get input signal
status.

COMMAND

#SIGNAL?in_index<CR>

FEEDBACK

~nn@SIGNALin_index,status<CR><LF>

in_index – Number that indicates the specific

input:
1–34

status – Signal status according to signal

validation:

0 – Off
1 – On

Get the input signal
status of IN 1:

#SIGNAL?1<CR>

SN?

Get device serial

number.

COMMAND

#SN?<CR>

FEEDBACK

~nn@SNserial_num<CR><LF>

serial_num – 14 decimal digits, factory

assigned

Get the device
serial number:

#SN?<CR>

TEST-MODE

Put device into
keyboard testing
mode.

Refer to User
Manual for test
instructions.

COMMAND

#TEST-MODE<CR>

FEEDBACK

~nn@TEST-MODEresult<CR><LF>

result – OK – Device has entered keyboard

testing mode

Put device into
keyboard testing
mode:

#TEST-MODE<CR>

TIME

Set device time and
date.

The year must be
4 digits.

The device does not
validate the day of
week from the date.

Time format - 24
hours.

Date format - Day,
Month, Year.

COMMAND

#TIMEday_of_week,date,time<CR>

FEEDBACK

~nn@TIMEday_of_week,date,time<CR><LF>

day_of_week – One of

{SUN,MON,TUE,WED,THU,FRI,SAT}

date – Format: DD-MM-YYYY.
time – Format: hh:mm:ss where

hh = hours
mm = minutes
ss = seconds

Set device time and
date to December
5, 2018 at 2:30pm:

#TIMEmon05­12­2018,14:30:00<

CR>

TIME?

Get device time and
date.

The year must be
4 digits.

The device does not
validate the day of
week from the date.

Time format - 24
hours.

Date format - Day,
Month, Year.

COMMAND

#TIME?<CR>

FEEDBACK

~nn@TIMEday_of_week,date,time<CR><LF>

day_of_week – One of

{SUN,MON,TUE,WED,THU,FRI,SAT}

date – Format: DD-MM-YYYY where

DD = Day
MM = Month

YYYY = Year

time – Format: hh:mm:ss where

hh = hours
mm = minutes
ss = seconds

Get device time
and date:

#TIME?<CR>

TREBLE

Set audio treble level.

COMMAND

#TREBLEio_index,treble_level<CR>

FEEDBACK

~nn@TREBLEio_index,treble_level<CR><LF>

io_index – Number that indicates the specific

input or output port:
1–34

treble_level – Audio parameter in Kramer

units, minus sign precedes negative values

0-15
++ increase current value
– decrease current value

Set audio treble
level:

#TREBLE1,1<CR

>

TREBLE?

Get audio treble level.

COMMAND

#TREBLE?io_index<CR>

FEEDBACK

~nn@TREBLEio_index,treble_level<CR><LF>

io_index – Number that indicates the specific

input or output port:
1–34

treble_level – Audio parameter in Kramer

units, minus sign precedes negative values

0-15

Get audio treble
level:

#TREBLE?1<CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

60

Function

Description

Syntax

Parameters/Attributes

Example

VERSION?

Get firmware version
number.

COMMAND

#VERSION?<CR>

FEEDBACK

~nn@VERSIONfirmware_version<CR><LF>

firmware_version – XX.XX.XXXX where the

digit groups are: major.minor.build version

Get the device
firmware version
number:

#VERSION?<CR>

VID

Set video switch state.

COMMAND

#VIDin_id>out_id<CR>

FEEDBACK

~nn@VIDin_id>out_id<CR><LF>

in_id – Indicates the ID of the input:

0 – Disconnect output
1–34

> – Connection character between in and out

parameters

out_id – Output number

1–34
* for all outputs

Switch IN 1 to OUT
3:

#VID1>3<CR>

VID?

Get video switch
state.

The GET
command identifies
input switching on
Step-in clients.

The SET
command is for
remote input switching
on Step-in clients
(essentially via by the
Web).

COMMAND

#VID?out_id<CR>

FEEDBACK

~nn@VID>out_id<CR><LF>

in_id – Indicates the ID of the input:

0 – Output disconnected
1–34

> – Connection character between in and out

parameters

out_id – Output number

1–34
* for all outputs

Get video switch
state:

#VID?2<CR>

X-MUTE

Set mute ON/OFF on
a specific signal.

This command is
designed to Mute a
Signal. This means
that it could be
applicable on any type
of signal. Could be
audio, video and
maybe IR, USB, or
data if this capability is
supported by the
product.

COMMAND

#X-MUTE<direction_type>. <port_format>.

<port_index>. <signal_type>. <index>,state<CR>

FEEDBACK

~nn@X-MUTE<direction_type>. <port_format>.

<port_index>. <signal_type>.
<index>,state<CR><LF>

The following attributes comprise the signal ID:

▪ <direction_type> – Direction of the port:

o IN – Input
o OUT – Output

▪ <port_format> – Type of signal on the

port:

o ANALOG_AUDIO

▪ <port_index> – The port number as

printed on the front or rear panel

▪ <signal_type> – Signal ID attribute:

o AUDIO

▪ <index> – 1

state – OFF/ON (not case sensitive)

Mute the video on
HDMI OUT 2:

hd.outMUTE-#X

mi.2.video.1,o

n<CR>

X-MUTE?

Get mute ON/OFF
state on a specific
signal.

COMMAND

#X-MUTE?<direction_type>. <port_format>.

<port_index>. <signal_type>. <index><CR>

FEEDBACK

~nn@X-MUTE<direction_type>. <port_format>.

<port_index>. <signal_type>.
<index>,state<CR><LF>

The following attributes comprise the signal ID:

▪ <direction_type> – Direction of the port:

o IN – Input
o OUT – Output

▪ <port_format> – Type of signal on the

port:

o ANALOG_AUDIO

▪ <port_index> – The port number as

printed on the front or rear panel

▪ <signal_type> – Signal ID attribute:

o AUDIO

▪ <index> – 1

state – OFF/ON (not case sensitive)

Get the mute
ON/OFF state on a
specific signal:

#X-MUTE?out.h

dmi.4.video.1<

CR>

Kramer Electronics Ltd.

VS-34FD – Protocol 3000

61

Result and Error Codes

Syntax

In case of an error, the device responds with an error message. The error message syntax:

• ~NN@ERR XXX<CR><LF> – when general error, no specific command

• ~NN@CMD ERR XXX<CR><LF> – for specific command

• NN – machine number of device, default = 01

• XXX – error code

Error Codes

Error Name

Error
Code

Description

P3K_NO_ERROR

0

No error

ERR_PROTOCOL_SYNTAX

1

Protocol syntax

ERR_COMMAND_NOT_AVAILABLE

2

Command not available

ERR_PARAMETER_OUT_OF_RANGE

3

Parameter out of range

ERR_UNAUTHORIZED_ACCESS

4

Unauthorized access

ERR_INTERNAL_FW_ERROR

5

Internal FW error

ERR_BUSY

6

Protocol busy

ERR_WRONG_CRC

7

Wrong CRC

ERR_TIMEDOUT

8

Timeout

ERR_RESERVED

9

(Reserved)

ERR_FW_NOT_ENOUGH_SPACE

10

Not enough space for data (firmware, FPGA…)

ERR_FS_NOT_ENOUGH_SPACE

11

Not enough space – file system

ERR_FS_FILE_NOT_EXISTS

12

File does not exist

ERR_FS_FILE_CANT_CREATED

13

File can’t be created

ERR_FS_FILE_CANT_OPEN

14

File can’t open

ERR_FEATURE_NOT_SUPPORTED

15

Feature is not supported

ERR_RESERVED_2

16

(Reserved)

ERR_RESERVED_3

17

(Reserved)

ERR_RESERVED_4

18

(Reserved)

ERR_RESERVED_5

19

(Reserved)

ERR_RESERVED_6

20

(Reserved)

ERR_PACKET_CRC

21

Packet CRC error

ERR_PACKET_MISSED

22

Packet number isn't expected (missing packet)

ERR_PACKET_SIZE

23

Packet size is wrong

ERR_RESERVED_7

24

(Reserved)

ERR_RESERVED_8

25

(Reserved)

ERR_RESERVED_9

26

(Reserved)

ERR_RESERVED_10

27

(Reserved)

ERR_RESERVED_11

28

(Reserved)

ERR_RESERVED_12

29

(Reserved)

ERR_EDID_CORRUPTED

30

EDID corrupted

ERR_NON_LISTED

31

Device specific errors

ERR_SAME_CRC

32

File has the same CRC – no changed

ERR_WRONG_MODE

33

Wrong operation mode

ERR_NOT_CONFIGURED

34

Device/chip was not initialized

The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:

What is Covered

This limited warranty covers defects in materials and workmanship in this product.

What is Not Covered

This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use
or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to
the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting
from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone
unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship
of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the
technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other
product or technology with which the product may be used.

How Long this Coverage Lasts

The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:

1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year
warranty for firmware and software updates; all Kramer VIA accessories, adapters, tags, and dongles are covered by a standard one (1) year
warranty.

2. Kramer fiber optic cables, adapter-size fiber optic extenders, pluggable optical modules, active cables, cable retractors, ring mounted
adapters, portable power chargers, Kramer speakers, and Kramer touch panels are all covered by a standard one (1) year warranty.

3. All Kramer Cobra products, all Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all
streaming, and all wireless products are covered by a standard three (3) year warranty.

4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.

5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for
three (3) years).

6. K-Touch software is covered by a standard one (1) year warranty for software updates.

7. All Kramer passive cables are covered by a ten (10) year warranty.

Who is Covered

Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or
owners of this product.

What Kramer Electronics Will Do

Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper
claim under this limited warranty:

1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and
labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs
necessary to return this product once the repair is complete.

2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same
function as the original product. If a direct or similar replacement product is supplied, the original product’s end warranty date remains
unchanged and is transferred to the replacement product.

3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought
under this limited warranty.

What Kramer Electronics Will Not Do Under This Limited Warranty

If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned
uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re­installation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any
adjustment of user controls or any programming required for a specific installation of this product.

How to Obtain a Remedy Under This Limited Warranty

To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this
product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service
providers, visit our web site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer
Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be
required (RMA number). You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original
carton, for shipping. Cartons not bearing a return authorization number will be refused.

Limitation of Liability

THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE
PRICE PAID FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR
DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR
UNDER ANY OTHER LEGAL THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental,
consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.

Exclusive Remedy

TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE
MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER
ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED
WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY
ACT (15 U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT
APPLY TO YOU, AND ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
THE PARTICULAR PURPOSE, SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.

Other Conditions

This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by
Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an
authorized Kramer Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this
document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the
online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of
satisfaction.

www.KramerAV.com
[e-mail]

P/N:

2900-301210

Rev:

2

SAFETY WARNING

Disconnect the unit from the power supply before opening and servicing

For the latest information on our products and a list of Kramer distributors, visit our website where
updates to this user manual may be found.

We welcome your questions, comments, and feedback.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All brand names, product names, and trademarks are the property of their respective owners.