Kontron Qseven-Eval Carrier User Manual

Download



USER GUIDE

www.kontron.com // 1

QSEVEN-Eval Carrier

Doc. Rev. 1.1

Doc. ID: 1062-1574

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 2

This page has been intentionally left blank

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 3



QSEVEN

-EVAL CARRIER - USER GUIDE

Disclaimer

Kontron would like to point out that the information contained in this user guide may be subject to alteration, particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee on the part of Kontron with respect to technical processes described in the user guide or any product characteristics set out in the user guide. Kontron assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright or mask work rights to these products and makes no representations or warranties that these products are free from patent, copyright or mask work right infringement unless otherwise specified. Applications that are described in this user guide are for illustration purposes only. Kontron makes no representation or warranty that such application will be suitable for the specified use without further testing or modification. Kontron expressly informs the user that this user guide only contains a general description of processes and instructions which may not be applicable in every individual case. In cases of doubt, please contact Kontron.

This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron. Kontron points out that the information contained in this user guide is constantly being updated in line with the technical alterations and improvements made by Kontron to the products and thus this user guide only reflects the technical status of the products by Kontron at the time of publishing.

Brand and product names are trademarks or registered trademarks of their respective owners.

Kontron S&T AG

Lise-Meitner-Str. 3-5 86156 Augsburg Germany www.kontron.com

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 4

Intended Use

THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL OR COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC CONTROL, LIFE SUPPORT OR LIFE SUSTAINING APPLICATIONS, WEAPONS SYSTEMS, OR ANY OTHER APPLICATION IN A HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE, OR IN WHICH THE FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS").

You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at your risk. To minimize the risks associated with your products and applications, you should provide adequate design and operating safeguards. You are solely responsible for compliance with all legal, regulatory, safety, and security related requirements concerning your products. You are responsible to ensure that your systems (and any Kontron hardware or software components incorporated in your systems) meet all applicable requirements. Unless otherwise stated in the product documentation, the Kontron device is not provided with error-tolerance capabilities and cannot therefore be deemed as being engineered, manufactured or setup to be compliant for implementation or for resale as device in High Risk Applications. All application and safety related information in this document (including application descriptions, suggested safety measures, suggested Kontron products, and other materials) is provided for reference only.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 5

Revision History

Revision Brief Description of Changes Date of Issue Author

1.0 Initial version 2018-Sept-11 CW

1.1 Chapter 7.28: caution note added 2018-Oct-08 HJS

Terms and Conditions

Kontron warrants products in accordance with defined regional warranty periods. For more information about warranty compliance and conformity, and the warranty period in your region, visit http://www.kontron.com/termsand-conditions.

Kontron sells products worldwide and declares regional General Terms & Conditions of Sale, and Purchase Order Terms & Conditions. Visit http://www.kontron.com/terms-and-conditions

For contact information, refer to the corporate offices contact information on the last page of this user guide or visit our website CONTACT US.

Customer Support

Find Kontron contacts by visiting: http://www.kontron.com/support.

Customer Service

As a trusted technology innovator and global solutions provider, Kontron extends its embedded market strengths into a services portfolio allowing companies to break the barriers of traditional product lifecycles. Proven product expertise coupled with collaborative and highly-experienced support enables Kontron to provide exceptional peace of mind to build and maintain successful products.

For more details on Kontron’s service offerings such as: enhanced repair services, extended warranty, Kontron training academy, and more visit http://www.kontron.com/support-and-services/services

Customer Comments

If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact Kontron support

. Detail any errors you find. We will correct the errors or problems as soon as possible and post the

revised user guide on our website.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 6

Symbols

The following symbols may be used in this user guide.

DANGER indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

NOTICE indicates a property damage message.

CAUTION indicates a hazardous situation which, if not avoided,

may result in minor or moderate injury.

Electric Shock!

This symbol and title warn of hazards due to electrical shocks (> 60 V) when touching products or parts of products. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material.

ESD Sensitive Device!

This symbol and title inform that the electronic boards and their components are sensitive to static electricity. Care must therefore be taken during all handling operations and inspections of this product in order to ensure product integrity at all times.

HOT Surface! Do NOT touch! Allow to cool before servicing.

Laser!

This symbol inform of the risk of exposure to laser beam and light emitting devices (LEDs) from an electrical device. Eye protection per manufacturer notice shall review before servicing.

This symbol indicates general information about the product and the user guide. This symbol also indicates detail information about the specific product configuration.

This symbol precedes helpful hints and tips for daily use.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 7

For Your Safety

Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation. Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines.

High Voltage Safety Instructions

As a precaution and in case of danger, the power connector must be easily accessible. The power connector is the product’s main disconnect device.

Warning All operations on this product must be carried out by sufficiently skilled personnel only.

Electric Shock! Before installing a non hot-swappable Kontron product into a system always ensure that

your mains power is switched off. This also applies to the installation of piggybacks. Serious electrical shock hazards can exist during all installation, repair, and maintenance operations on this product. Therefore, always unplug the power cable and any other cables which provide external voltages before performing any work on this product.

Earth ground connection to vehicle’s chassis or a central grounding point shall remain connected. The earth ground cable shall be the last cable to be disconnected or the first cable to be connected when performing installation or removal procedures on this product.

Special Handling and Unpacking Instruction

ESD Sensitive Device! Electronic boards and their components are sensitive to static electricity. Therefore, care

must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times.

Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is otherwise protected.

Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands or tools. This is most easily done by touching a metal part of your system housing.

It is particularly important to observe standard anti-static precautions when changing piggybacks, ROM devices, jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the product is not placed on conductive surfaces, including anti-static plastics or sponges. They can cause short circuits and damage the batteries or conductive circuits on the product.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 8

Lithium Battery Precautions

If your product is equipped with a lithium battery, take the following precautions when replacing the battery.

Danger of explosion if the battery is replaced incorrectly.

 Replace only with same or equivalent battery type recommended by the manufacturer.

 Dispose of used batteries according to the manufacturer’s instructions.

General Instructions on Usage

In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received from Kontron Support as a special handling instruction, will void your warranty.

This product should only be installed in or connected to systems that fulfill all necessary technical and specific environmental requirements. This also applies to the operational temperature range of the specific board version that must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.

In performing all necessary installation and application operations, only follow the instructions supplied by the present user guide.

Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship the product then re-pack it in the same manner as it was delivered.

Special care is necessary when handling or unpacking the product. See Special Handling and Unpacking Instruction.

Quality and Environmental Management

Kontron aims to deliver reliable high-end products designed and built for quality, and aims to complying with environmental laws, regulations, and other environmentally oriented requirements. For more information regarding Kontron’s quality and environmental responsibilities, visit http://www.kontron.com/about-kontron/corporateresponsibility/quality-management.

Disposal and Recycling

Kontron’s products are manufactured to satisfy environmental protection requirements where possible. Many of the components used are capable of being recycled. Final disposal of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.

WEEE Compliance

The Waste Electrical and Electronic Equipment (WEEE) Directive aims to:

 Reduce waste arising from electrical and electronic equipment (EEE)

 Make producers of EEE responsible for the environmental impact of their products, especially when the product

beQSEVEN waste

 Encourage separate collection and subsequent treatment, reuse, recovery, recycling and sound environmental

disposal of EEE

 Improve the environmental performance of all those involved during the lifecycle of EEE

Environmental protection is a high priority with Kontron. Kontron follows the WEEE directive You are encouraged to return our products for proper disposal.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 9

Table of Contents

Symbols ................................................................................................................................................................................................................. 6

For Your Safety ................................................................................................................................................................................................... 7

High Voltage Safety Instructions ................................................................................................................................................................. 7

Special Handling and Unpacking Instruction ........................................................................................................................................... 7

Lithium Battery Precautions ......................................................................................................................................................................... 8

General Instructions on Usage ..................................................................................................................................................................... 8

Quality and Environmental Management ................................................................................................................................................ 8

Disposal and Recycling ................................................................................................................................................................................... 8

WEEE Compliance ............................................................................................................................................................................................. 8

Table of Contents............................................................................................................................................................................................... 9

List of Tables ..................................................................................................................................................................................................... 10

List of Figures .................................................................................................................................................................................................... 12

1/ Introduction .......................................................................................................................................................................................... 13

2/ Product Description ........................................................................................................................................................................... 14

3/ Installation Procedure ...................................................................................................................................................................... 15

3.1. Packing Check List ..................................................................................................................................................................................... 15

3.2. Requirements IEC62368-1 ..................................................................................................................................................................... 15

4/ Product Specification ........................................................................................................................................................................ 16

4.1. Block Diagram ............................................................................................................................................................................................ 16

4.2. Component Main Data ............................................................................................................................................................................ 17

4.3. Environmental Conditions and Standard & Approvals ................................................................................................................ 19

4.4. Mainboard View and I/O Locations ................................................................................................................................................... 20

5/ Jumpers and Connectors ................................................................................................................................................................ 23

6/ Maintenance and Status Information ......................................................................................................................................... 25

6.1. LEDs .............................................................................................................................................................................................................. 25

7/ Pin Definitions ..................................................................................................................................................................................... 27

7.1. QSEVEN Connector (J1) ........................................................................................................................................................................... 28

7.2. LVDS Connector (J23) .............................................................................................................................................................................. 31

7.3. Backlight Connector (J32) ..................................................................................................................................................................... 32

7.4. Dual Stacked DP Connector (Display Port) (J2) ............................................................................................................................. 32

7.5. HDMI connector (J4) ............................................................................................................................................................................... 34

7.6. DP connector (J3) ..................................................................................................................................................................................... 35

7.7. Mini PCIe Card Socket 0 (J45) & Mini PCIe Card Socket 1 (J46) .................................................................................................. 36

8.8. SIM card socket (J53) ............................................................................................................................................................................. 37

7.9. PCIe x1 connectors (J40, J41) ................................................................................................................................................................ 37

7.10. Mini SATA Card Socket (J54) ............................................................................................................................................................... 38

7.11. SATA Connector (J55) ............................................................................................................................................................................ 39

7.12. Audio Connector Line In & Out (J38 & J39) .................................................................................................................................... 39

7.13. Audio Connector (J36)........................................................................................................................................................................... 40

7.14. RTC battery holder (J65) ...................................................................................................................................................................... 40

7.15. USB 2.0 OTG Connector (J22) .............................................................................................................................................................. 41

7.16. USB Hub Connections (J34) ................................................................................................................................................................. 41

7.17. Double USB 3.0 Connector (J34) ........................................................................................................................................................ 43

7.18. LAN Connector (J33).............................................................................................................................................................................. 44

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 10

7.19. Micro-SD Card Connector (J56) ......................................................................................................................................................... 45

7.20. COM Connector (J58) ........................................................................................................................................................................... 45

7.21. CAN Connector (J57) .............................................................................................................................................................................. 46

7.22. LPC/GPIO Header (J59) ........................................................................................................................................................................ 46

7.23. Power Management Header (J62) ................................................................................................................................................... 47

7.24. SYS Signals Header (J37) .................................................................................................................................................................... 47

7.25. Thermal Header (J66) .......................................................................................................................................................................... 48

7.26. CPU Fan (J60) .......................................................................................................................................................................................... 48

7.27. SYS Fan (J61) ............................................................................................................................................................................................ 48

7.28. Power-In Connector (J21) ................................................................................................................................................................... 49

7.29. Module Power-In Connector (J64) .................................................................................................................................................. 49

7.30. ATX 24 Pin Connector (J20) ................................................................................................................................................................ 51

7.31. Button Switch (SW1,SW2,SW3,SW4) ................................................................................................................................................ 51

7.32. Jumpers .................................................................................................................................................................................................... 53

7.32.1. Boot Alternate Jumper (J14) ............................................................................................................................................................ 53

7.32.2. Display Power Select Jumper (J24) .............................................................................................................................................. 53

7.32.3. Backlight Power of the Select Jumper (J25) .............................................................................................................................. 53

7.32.4. Dual DP/LVDS Select Jumper (J26) .............................................................................................................................................. 53

7.32.5. Dual DP++/HDMI Select Jumper (J27) ......................................................................................................................................... 53

7.32.6. Audio Channel Jumper for I2S or HDA (J35) ............................................................................................................................... 54

7.32.7. mPCIe-0WLAN Disable Jumper (J5,J6) ........................................................................................................................................ 54

7.32.8. mPCIe-1WLAN Disable Jumper (J7,J8) ......................................................................................................................................... 54

7.32.9. microSD Write Protect Jumper (J9) .............................................................................................................................................. 54

7.32.10. CAN Bus Termination Jumper (J10) ............................................................................................................................................ 54

7.32.11. LPC/GPIO Selection Jumper (J11) .................................................................................................................................................. 54

7.32.12. CPU Fan Power Selection Jumper (J30) .................................................................................................................................... 55

7.32.13. SYS Fan Power Selection Jumper (J29) ..................................................................................................................................... 55

7.32.14. SYS Fan PWM Control Selection Jumper (J18) ........................................................................................................................ 55

7.32.15. ATX PSU Control Selection Jumper (J28) .................................................................................................................................. 55

7.32.16. ATX PSU ON Selection Jumper (J17) ............................................................................................................................................ 55

7.32.17. LEDs Enable Jumper (J19) .............................................................................................................................................................. 55

7.32.18. RTC Jumper (J31) ............................................................................................................................................................................... 56

7.32.19. Module Standby Voltage (J67) ..................................................................................................................................................... 56

7.32.20. TACHOIN CPU Fan/SYS Fan (J68) ............................................................................................................................................... 56

Appendix A: List of Acronyms ...................................................................................................................................................................... 57

About Kontron .................................................................................................................................................................................................. 58

List of Tables

Table 1: Component Main Data .................................................................................................................................................................... 17

Table 2: Environmental Conditions and Standard & Approvals ....................................................................................................... 19

Table 3: Jumpers and Connectors of Q7EVAL ........................................................................................................................................ 23

Table 4: Power LEDs ....................................................................................................................................................................................... 25

Table 5: Watchdog LEDs ................................................................................................................................................................................ 25

Table 6: Backlight Voltage LEDs ................................................................................................................................................................. 25

Table 7: GPIO LEDs ........................................................................................................................................................................................... 26

Table 8: Audio selection LEDs ..................................................................................................................................................................... 26

Table 9: SATA Activity LEDs.......................................................................................................................................................................... 26

Table 10: mPCIe slot A LEDs ......................................................................................................................................................................... 26

Table 11: mPCIe slot B LEDs .......................................................................................................................................................................... 26

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 11

Table 12: Connector Definitions .................................................................................................................................................................. 27

Table 13: QSEVEN Connector Pin Assignment ........................................................................................................................................ 28

Table 14: 30-pin LVDS connector ................................................................................................................................................................ 31

Table 15: 7-pin Backlight Connector .......................................................................................................................................................... 32

Table 16: Dual Stacked DP Connector ....................................................................................................................................................... 32

Table 17: 19-pin HDMI connector ................................................................................................................................................................ 34

Table 18: 20-pin DP connector .................................................................................................................................................................... 35

Table 19: 52-pin Mini PCIe Card .................................................................................................................................................................. 36

Table 20: 8-pin SIM card socket ................................................................................................................................................................. 37

Table 21: 52-pin PCIe x1 connector ............................................................................................................................................................ 37

Table 22: 52-pin SATA Card Socket ........................................................................................................................................................... 38

Table 23: SATA Connector ............................................................................................................................................................................ 39

Table 24: Audio Jacks Pin Assignment (Line Out, green) .................................................................................................................... 39

Table 25: Audio Jacks Pin Assignment (Line In, blue) .......................................................................................................................... 39

Table 26: 9-pin Audio Connector Header ................................................................................................................................................ 40

Table 27: RTC battery holder ....................................................................................................................................................................... 40

Table 28: µUSB 2.0 OTG Connector ............................................................................................................................................................ 41

Table 29 : USB 3.0 Pin Assignment ............................................................................................................................................................. 41

Table 30 : USB 3.0 Pin Description ............................................................................................................................................................. 42

Table 31: Double USB 3.0 Connector ......................................................................................................................................................... 43

Table 32: LAN Connector ............................................................................................................................................................................... 44

Table 33: LAN Left LEDs State ..................................................................................................................................................................... 44

Table 34: LAN Right LEDs State .................................................................................................................................................................. 44

Table 35: Micro-SD Card Connector .......................................................................................................................................................... 45

Table 36: COM Connector ............................................................................................................................................................................. 45

Table 37: CAN Connector ............................................................................................................................................................................... 46

Table 38: LPC/GPIO Header .......................................................................................................................................................................... 46

Table 39: Power Management Header ..................................................................................................................................................... 47

Table 40: SYS Signals Header ...................................................................................................................................................................... 47

Table 41: Thrm Header ................................................................................................................................................................................... 48

Table 42: 4-pin CPU Fan Connector .......................................................................................................................................................... 48

Table 43: 3-pin SYS Fan Connector ........................................................................................................................................................... 48

Table 44: Power-In Connector .................................................................................................................................................................... 49

Table 45: Module Power-In Connector .................................................................................................................................................... 49

Table 46: ATX 24 Pin Connector .................................................................................................................................................................. 51

Table 47: Reset Button (SW1, J12) ............................................................................................................................................................... 51

Table 48: Power Button (SW2, J13) ............................................................................................................................................................. 51

Table 49: Sleep Button (SW3, J15) .............................................................................................................................................................. 52

Table 50: Lid Button (SW4, J16) ................................................................................................................................................................... 52

Table 51: Boot Alternate Jumper (J14) ....................................................................................................................................................... 53

Table 52: Display Power Select Jumper (J24) ........................................................................................................................................ 53

Table 53: Backlight Power Select Jumper (J25) ..................................................................................................................................... 53

Table 54: Dual DP/LVDS Select Jumper (J26) ......................................................................................................................................... 53

Table 55: Dual DP++/HDMI Select Jumper (J27) .................................................................................................................................... 53

Table 56: Audio Channel Jumper for I2S or HDA (J35) ......................................................................................................................... 54

Table 57: mPCIe-0WLAN Disable Jumper (J5,J6) ................................................................................................................................... 54

Table 58: mPCIe-1WLAN Disable Jumper (J7,J8) ................................................................................................................................... 54

Table 59: microSD Write Protect Jumper (J9)......................................................................................................................................... 54

Table 60: CAN Bus Termination Jumper (J10) ......................................................................................................................................... 54

Table 61: LPC/GPIO Selection Jumper (J11) .............................................................................................................................................. 54

Table 62: CPU Fan Power Selection Jumper (J30) ................................................................................................................................. 55

Table 63: SYS Fan Power Selection Jumper (J29) ................................................................................................................................. 55

Table 64: SYS Fan PWM Control Selection Jumper (J18) .................................................................................................................... 55

Table 65: ATX PSU Control Selection Jumper (J28) .............................................................................................................................. 55

Table 66: ATX PSU ON Selection Jumper (J17) ........................................................................................................................................ 55

Table 67: LEDs Enable Jumper (J19) ........................................................................................................................................................... 55

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 12

Table 68: RTC Jumper (J31) ........................................................................................................................................................................... 56

Table 69: Module Standby Voltage (J67 ................................................................................................................................................... 56

Table 70: TACHOIN CPU Fan/SYS Fan (J68) ............................................................................................................................................ 56

Table 71: List of Acronyms ............................................................................................................................................................................. 57

List of Figures

Figure 1: Block Diagram for the QSEVEN-EVAL Carrier ........................................................................................................................ 16

Figure 2: Qseven Module Power Setting Resistors ............................................................................................................................... 16

Figure 3: Top View ........................................................................................................................................................................................... 20

Figure 4: Rear View .......................................................................................................................................................................................... 21

Figure 5: Front View ......................................................................................................................................................................................... 21

Figure 6: Right Side View ............................................................................................................................................................................... 22

Figure 7: Left Side View.................................................................................................................................................................................. 22

Figure 8: Power LEDs ..................................................................................................................................................................................... 25

Figure 9: GPIO LEDS ......................................................................................................................................................................................... 25

Figure 10: 30-pin LVDS connector ............................................................................................................................................................... 31

Figure 11: 7-pin Backlight Connector ......................................................................................................................................................... 32

Figure 12: Dual Stacked DP Connector ...................................................................................................................................................... 32

Figure 13: 19-pin HDMI connector .............................................................................................................................................................. 34

Figure 14: 20-pin DP connector .................................................................................................................................................................. 35

Figure 15: 52-pin Mini PCIe Card ................................................................................................................................................................ 36

Figure 16: 8-pin SIM card socket ................................................................................................................................................................ 37

Figure 17: 52-pin PCIe x1 connector ........................................................................................................................................................... 37

Figure 18: 52-pin SATA Card Socket .......................................................................................................................................................... 38

Figure 19: SATA Connector ............................................................................................................................................................................ 39

Figure 20: Audio Jacks .................................................................................................................................................................................... 39

Figure 21: 9-pin Audio Connector Header ................................................................................................................................................ 40

Figure 22: RTC battery holder ...................................................................................................................................................................... 40

Figure 23: µUSB 2.0 OTG Connector ........................................................................................................................................................... 41

Figure 24: USB 2.0 / 3.0 socket .................................................................................................................................................................... 41

Figure 25: Double USB 3.0 Connector ....................................................................................................................................................... 43

Figure 26: LAN Connector ............................................................................................................................................................................. 44

Figure 27: Micro-SD Card Connector ......................................................................................................................................................... 45

Figure 28: COM Connector ............................................................................................................................................................................ 45

Figure 29: CAN Connector ............................................................................................................................................................................. 46

Figure 30: LPC/GPIO Header ........................................................................................................................................................................ 46

Figure 31: Power Management Header .................................................................................................................................................... 47

Figure 32: SYS Signals Header ..................................................................................................................................................................... 47

Figure 33: Thrm Header ................................................................................................................................................................................. 48

Figure 34: 4-pin CPU Fan Connector ......................................................................................................................................................... 48

Figure 35: 3-pin SYS Fan Connector .......................................................................................................................................................... 48

Figure 36: Power-In Connector ................................................................................................................................................................... 49

Figure 37: Module Power-In Connector ................................................................................................................................................... 49

Figure 38: ATX 24 Pin Connector ................................................................................................................................................................. 51

Figure 39: Button Switch ................................................................................................................................................................................ 51

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 13

1/ Introduction

This user guide describes the Qseven-Eval carrier board. This document describes the electronic, mechanical and thermal design of the QSEVEN evaluation carrier board. It is designed to test the Qseven-Q7AL and other QSEVEN 2.1 modules. The board is equipped with DP++ connector, HDMI connector, LVDS connector, two full-size or half-size mPCIe card slot (PCIe + USB 2.0), two PCIe x1 slot and full-size mSATA slot to easily use and test additional cards.

The use of this user guide implies a basic knowledge of PC hardware and software. This user guide is focused on describing the special features and is not intended to be a standard PC textbook. New users are recommended to study the short installation procedure stated in the following chapter before switching on the power. All configuration and setup of the CPU board is either done automatically or manually by the user via the BIOS setup menus.

Latest revision of this user guide, datasheet, BIOS, drivers and BSPs (Board Support Packages) can be downloaded from Kontron’s Web Page.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 14

2/ Product Description

The Qseven-Eval Carrier Board designed based on the latest QSEVEN design guide version 2.0 is equipped with:

 DP++ connector

 HDMI connector

 Dual stacked Display Port

 LVDS connector

 Two full-size or half-size mPCIe card slot (PCIe + USB 2.0), connected to SIM UIM

 Two PCIe x1 slot

 SIM card slot

 Full-size mSATA slot

 SATA

 Micro SD

 Dual stacked USB 3.0/2.0 connector and one micro USB 2.0 OTG connector

 LPC/GPIO Header



SPI SO8 Socket

 COM port (DSUB DB9)

 Audio (I2S or HDA)

 Battery holder

 CAN interface

 Gigabit Ethernet

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 15

3/ Installation Procedure

3.1. Packing Check List

The package includes the following basic items accompany with this user guide.

 One Board

If this item is either damaged or missing, please contact your vendor and save all packing materials for future replacement and maintenance.

Note: The above packing list is for standard single box packing only.

3.2. Requirements IEC62368-1

Take care when designing chassis interface connectors in order to fulfill the IEC62368-1 standard.

Users of board must evaluate the end product to ensure compliance the requirements of the IEC62368-1 safety standard are met:

 The motherboard must be installed in a suitable mechanical, electrical and fire enclosure.

 The system in its enclosure must be evaluated for temperature and air flow considerations.

 For interfaces having a power pin such as external power or fan, ensure that the connectors and wires are

suitably rated. All connections from or to the product shall be with Safety Extra Low Voltage (SELV) circuits only.

 Wires have suitable rating to withstand the maximum available power.

 The enclosure of the peripheral device fulfills the fire protecting requirements of IEC62368-1.

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 16

4/ Product Specification

4.1. Block Diagram

Figure 1: Block Diagram for the QSEVEN-EVAL Carrier

To power the Qseven Module the power can be set to Ext/Int power by populating one of the following resistors.

 R468 – V_MOD_IN from internal (V_5V0_S5) [Default setting]

 R467 – V_MOD_IN from external (V_3V0-5V25_IN)

Figure 2: Qseven Module Power Setting Resistors

Location of R468 (V_5V0_S5) the default setting

Location of R467 (V_3V0-5V25_IN)

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 17

4.2. Component Main Data

The table below summarizes the features of the motherboard.

Table 1: Component Main Data

Qseven-Eval Carrier

Form factor Carrier board with 210 mm x 200 mm.

Memory

EEPROM System (U71)

The EEPROM type 24LC64 on carrier board connected to QSEVEN GP I2C or SM bus.

SPI flash socket (J63)

SPI flash socket (SOIC8 – 1045-8636) with flash memory W25Q128

EEPROM DDC optional

(U32)

The EDID EEPROM type 24C04 on carrier board connected to LVDS_I2C bus. Holding display relevant DDC information. Used by BIOS to initialize LCD. KEAPI support with module.

External I/O

LAN 1x Gbit-Ethernet port

USB 2x USB 3.0 double stack and 1x μUSB connector for On The Go (OTG) function: powered for

host, not powered for client. The 5 V output from USB 2.0 and USB OTG is separately electronically fused to 500 mA. The 5V output from USB 3.0 is electronically fused to 1000 mA each port.

HDMI HDMI connector from QSEVEN module

DP++ DP++ connector from QSEVEN module

COM1 COM RS232, 9-pin DSUB

Audio Line-in and line-out 3.5 mm jack; Front Panel 2x5 Pin Header (2.54 mm), supporting both

interfaces I2S and HDA selectable by jumper.

Internal I/O

LVDS 30-pin LVDS dual channel from QSEVEN module. Configurable 3.3 V / 5V voltage levels of

power for different panels via jumper.

Backlight Backlight PWM and power. Configurable 12 V/ 5 V voltage levels of backlight power for

different panels via jumper. Maximum Power is 12 W continuous. If the selected panel exceeds, the provided power by this carrier evaluation of the QSEVEN module with LVDS can still be done with external panel power.

eDP eDP connector, shared with LVDS as an option selectable by jumper. PWR Out must provide

+3.3 V +/-10 % with a maximum current of 500 mA and a minimum power capability of 1.5 W.

mSATA 1x slot (full size / half size ; SATA port)

LVDS One dual-channel LVDS. This is muxed with eDP0/eDP1 (jumper selectable) as per Qseven

specification.

PCIe X1 Two PCIe X1 slots

mPCIe Two card slots (full size / half size) - PCIe & USB; support all MC3 mPCIe cards

SIM Card SIM Card connected to both mPCIe

μSD microSD card socket from QSEVEN module

Controller Area Network (CAN)

CAN interface

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 18

LEDs SMD LEDs for storage activity, board status, device and power status (power good)

Internal Header and Jumper

GPIO/LPC GPIO/LPC Header 2.54 mm

Power Management Header

2.54 mm pin header, dual row

SYS Signals Header 2.54 mm pin header, dual row

Battery 1.5F Goldcap and/or CR2032 battery. Optional parallel usage supported.

CPU Fan 4-pin fan connector, Voltage can be 5 V or 12 V (default)

SYS Fan 3-pin fan connector, Voltage can be 5 V or 12 V (default)

Carrier Board Controllers

I2C EEPROM General purpose EEPROM I2C

SPI Socket SPI socket with 16 MB Flash

HDA Codec TSI 92HD73C HDA Codec

I2S Codec WM8904 I2S Codec

EEPROM DDC Holding display relevant DDC information. Used by BIOS to initialize LCD.

Carrier Board Power

Power Input 12 V input power connector, used as an alternative power for module to support wide

voltage range. 12 V DC power connector for powering carrier and module 5 V. Separate input power connector for module with voltage range: 3.0 V to 5.25 V DC

Optional 24-pin ATX Power Supply

LED status

Power LEDs Power good of carrier power lanes

CARRIER_PWR_ON Power on

CARRIER_STB# CARRIER_STB#

LVDS V_BKLT 5V, 12V indication LVDS backlight

Ethernet LEDs Ethernet status

HDA/I2S LEDs HDA / I2S Audio codec indication LEDs

mPCIE mode WPAN#, WLAN#, WWAN# indication

SATA_ACT# SATA activity LED

Power rails 1.8 V; 3.3 V; 5 V

GPIO GPIO indication LEDs

Watchdog Watchdog indication LED

Danger of explosion if the lithium battery is incorrectly replaced.

 Replace only with the same or equivalent type recommended by the manufacturer

 Dispose of used batteries according to the manufacturer’s instructions

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 19

4.3. Environmental Conditions and Standard & Approvals

The Qseven-Eval Carrier plan to comply with the following standards.

Table 2: Environmental Conditions and Standard & Approvals

Operating -40°C to +85°C

Storage -40°C to +85°C

Relative humidity (non-condensing) 93 % at 40°C

Electromagnetic Compatibility (EMC) and Interference (EMI)

The board shall be designed to meet the following requirements: EMC Emission EN 55032 Class B FCC part 15 Class B

Shock/Vibration/ Bump

According to: IEC/EN60068-2-64 IEC/EN60068-2-27

Theoretical MTBF Not applicable

RoHS II Compliance The product will comply to the European Council Restriction of Hazardous Substances

(RoHS) II Directive on the approximation of the laws of the member states relating to Directive 20011/65/EU or the last status thereof.

Safety Component recognition to EN 62368-1

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 20

4.4. Mainboard View and I/O Locations

Figure 3: Top View

1 QSeven Connector (J1)

2 CPU fan (J60)

3 System fan(J61)

4 SATA Connector (J55)

5 Mini SATA Card Socket (J54)

6 Mini PCIe card socket mPCIe_0 (J45)

7 Mini PCIe card socket mPCIe_1 (J46)

8 SIM card (J53)

9 Button switches ( reset, sleep, power,

LID)

10 Power Management Header (J62)

11 LPC/GPIO header (J59)

12 System Signals (J37)

13 RTC battery Holder

14 PCIe connector (J40)

15 PCIe connector ( J41)

4 14

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 21

Figure 4: Rear View

Figure 5: Front View

1 CAN connector (J57)

2 PCIE connector (J41)

3 COM connector(J58)

4 ATX connector (J20)

5 Power-In Connector (J21)

6 Module Power-In connector (J64)

1 3

4 5

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 22

Figure 6: Right Side View

1 HDMI (J4)

2 DP (J3)

3 Dual stack DP (J2)

4 LVDS Connector (J23)

5 Backlight connector (J32)

6 LAN (RJ45) Connector (J33)

Figure 7: Left Side View

1 USB 2.0 (J22)

2 Double USB 3.0 (J34)

3 Audio Jacks (J38, J39)

4 Backlight Connector (J32)

2 4

3 6 5 1 3

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 23

5/ Jumpers and Connectors

This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on the board are in the proper positionHardware Configuration Setting

In general, jumpers on the board are used to select options for certain features. Some of the jumpers are designed to be user-configurable, allowing for system enhancement. The others are for testing purpose only and should not be altered. To select any option, cover the jumper cap over (SHORT) or remove (NC) it from the jumper pins according to the following instructions. Here, NC stands for “Not Connect”.

Table 3: Jumpers and Connectors of Q7EVAL

Connector Function Remark

Module Power-in Connector (J64)

Module power-in selection from 3 V to 5.25 V. ATTENTION: J64 powers the module ONLY! Carrier still

needs to be powered via 12V, through (J21) Power-In connector or (J20) ATX Connector.

1x4-pin Connector

5 V/3.3 V (J24) Display voltage selection (3.3 V/5 V) 1x3-pin Jumper

5 V/12 V (J25) Display backlight voltage selection (5 V/12 V) 1x3-pin Jumper

Dual DisplayPort/HDMI (J27) Graphic Display selection (DP or DD0 in current) 1x3-pin Jumper

DP/LVDS (J26) Graphic Display selection (LVDS/DP) 1x3-pin Jumper

MPCIE_0_W_DISABLE1# (J5) Disable miniPCIe radio operation 1x2-pin Jumper

MPCIE_0_W_DISABLE2# (J6) Disable miniPCIe radio operation 1x2-pin Jumper

MPCIE_1_W_DISABLE1# (J7) Disable miniPCIe radio operation 1x2-pin Jumper

MPCIE_1_W_DISABLE2# (J8) Disable miniPCIe radio operation 1x2-pin Jumper

CODEC_OPTION_SW_I2S_HD A# (J35)

Audio Codec Multipexor HDA/I2S Codec 1x2-pin Jumper

microSD Write Protect (J9) microSD Write Protect Disable/Enable 1x2-pin Jumper

CAN Bus Termination (J10) CAN Bus Termination Enable/Disable 1x2-pin Jumper

GPIO/LPC (J11) GPIO/LPC to Header 1x2-pin Jumper

CPU Fan 12V/5V (J30) CPU Fan 12V/5V 1x3-pin Jumper

System Fan 12V/5V (J29) Sys Fan 12V/5V 1x3-pin Jumper

System Fan PWM control (J18)

System Fan without/with PWM control 1x2-pin Jumper

Boot Selection (J14) Boot from Module/Carrier SPI Flash 1x2-pin Jumper

ATX PSU control (J28) Control by SUS_S3#/SUS_S5# 1x3-pin Jumper

ATX PSU force (J17) ATX PSU is controlled by module/Force ATX PSU to ON 1x2-pin Jumper

LEDs ENABLE (J19) Enable/Disable status and power LEDs 1x2-pin Jumper

V_BAT_JP (J31) Selection between Battery or Goldcap 1x3-pin Jumper

COM(RS232) (J58) Serial connector from QSEVEN module standard

USB 3.0 (J34) Dual Stacked USB 3.0 connectors standard

microUSB 2.0 OTG (J22) microUSB 2.0 connector standard

QSEVEN (J1) QSEVEN connector 1x230-pin header

CAN (J57) CAN, Molex 53261-0471 or similar 1x4 header

Gigabit Ethernet (J33) GBE connector standard

LVDS (J23) LVDS dual channel from QSEVEN module. Configurable

3.3 V / 5 V voltage levels of power for different panels

1x30 pins

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 24

Connector Function Remark

Backlight (J32) via jumper. 1x7 pins

HDMI (J4) HDMI connector from QSEVEN module standard

DP++ (J3) Display port connector from QSEVEN module standard

PCIe x1 (J40/J41) 2x PCIe 1x slot standard

mPCIe (J45/J46) 2x card slot (full size / half size) - PCIe & USB; support

all MC3 mPCIe cards

standard

SIM (J53) SIM card acceptor standard

mSATA (J54) 1x slot (full size / half size ; SATA port) standard

SATA (J55) SATA port 1 standard

microSD (J56) 1.10mm Pitch microSD Memory Card Connector standard

SPI socket (J63) SPI Flash socket, for SOIC8 standard

LPC/GPIO (J59) LPC/GPIO Header 2.54 mm 2x10 header

Audio (J38 IN/J39 OUT/J36 Front Panel)

Line-in and line-out 3.5 mm jack; Front Panel 2x5 Pin Header (2.54 mm)

Front Panel 2x5 header

Sys Signal Header (j37) System header signal (2.54 mm pin) 2x5 header

Power Management Header (J62)

Power Management Header (2.54 mm pin) 2x8 header

CPU Fan (J60) SYS Fan (J61)

CPU Fan connector System Fan connector

1x4 header 1x3 header

Module Standby Voltage (J67)

V_5V0_SB enable disable 1x 2-pin header

TACHOIN CPU Fan/SYS Fan (J68)

TACHOIN for FAN 1x 3-pin header

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 25

6/ Maintenance and Status Information

6.1. LEDs

Figure 8: Power LEDs

Table 4: Power LEDs

LED Color Signal Diode Function

Green V_1V8_S5 D33 Voltage V_1V8_S5 is present

Green V_1V8_S0 D34 Voltage V_1V8_S0 is present

Green V_1V5_S0 D35 Voltage V_1V5_S0 is present

Green V_3V3_S5 D30 Voltage V_3V3_S5 is present

Green V_3V3_S0 D31 Voltage V_3V3_S0 is present

Green V_5V0_S5 D32 Voltage V_5V0_S5 is present

Green V_5V0_S0 D36 Voltage V_5V0_S0 is present

Green V_12V0_S0 D37 Voltage V_12V0_S0 is present

Green V_2V5_STB D38 Voltage V_2V5_STB is present

Green Carrier_PWR_ON D39 Voltage Carrier_PWR_ON is present

Red Carrier_STBY D55 Voltage Carrier_STBY is present

Table 5: Watchdog LEDs

LED Color Signal Diode Function

Red WDT D54 Watchdog indication from module

Table 6: Backlight Voltage LEDs

LED Color Signal Diode Function

Green PG_BKLT_5V D28 Indicate backlight voltage is 5 V

Green PG_BKLT_12V0 D29 Indicate backlight voltage is out of range is 12 V

Figure 9: GPIO LEDS

Power LEDs GPIO LEDs

Watchdog LEDs

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 26

Table 7: GPIO LEDs

LED Color Signal Diode Function

Blue GPIO0 D62 GPIO0 level indication

Blue GPIO1 D63 GPIO1 level indication

Blue GPIO2 D64 GPIO2 level indication

Blue GPIO3 D65 GPIO3 level indication

Blue GPIO4 D58 GPIO4 level indication

Blue GPIO5 D59 GPIO5 level indication

Blue GPIO6 D60 GPIO6 level indication

Blue GPIO7 D61 GPIO7 level indication

Table 8: Audio selection LEDs

LED Color Signal Diode Function

Yellow CODEC_OPTION_

SW_I2S_HDA#

D40 I2S Codec is active; J35 is closed

Yellow CODEC_OPTION_

SW_I2S_HDA#

D41 HDA Codec is active; J35 is open

Table 9: SATA Activity LEDs

LED Color Signal Diode Function

Red SATA_ACT D51 Indicate SATA activity

Table 10: mPCIe slot A LEDs

LED Color Signal Diode Function

Yellow MPCIEA_WPAN# D44 WPAN Activity

Yellow MPCIEA_WLAN# D43 WLAN Activity

Yellow MPCIEA_WWAN# D42 WWAN Activity

Table 11: mPCIe slot B LEDs

LED Color Signal Diode Function

Yellow MPCIEB_WPAN# D47 WPAN Activity

Yellow MPCIEB_WLAN# D46 WLAN Activity

Yellow MPCIEB_WWAN# D45 WWAN Activity

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 27

7/ Pin Definitions

The following sections provide pin definitions and detailed description of all on-board connectors.

The connector definitions follow the following notation:

Table 12: Connector Definitions

Column Name Description

Pin Shows the pin-numbers in the connector. The graphical layout of the connector definition

tables is made similar to the physical connectors.

Signal The mnemonic name of the signal at the current pin.

The notation “XX#” states that the signal “XX” is active low.

Type AI: Analog Input

AO: Analog Output I: Input, TTL compatible if nothing else stated IO: Input / Output, TTL compatible if nothing else stated IOT: Bi-directional tristate IO pin. IS: Schmitt-trigger input, TTL compatible. IOC: Input / open-collector Output, TTL compatible IOD: Input / Output, CMOS level Schmitt-triggered (Open drain output) NC: Not Connected O: Output, TTL compatible OC: Output, open-collector or open-drain, TTL compatible OT: Output with tri-state capability, TTL compatible LVDS: Low Voltage Differential Signal PWR: Power supply or ground reference pins. Ioh: Typical current in mA flowing out of an output pin through a grounded load, while the output voltage is > 2.4 V DC (if nothing else stated). Iol: Typical current in mA flowing into an output pin from a VCC connected load, while the output voltage is < 0.4 V DC (if nothing else stated).

Pull U/D On-board pull-up or pull-down resistors on input pins or open-collector output pins.

Note Special remarks concerning the signal

Designation Type and number of item described

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 28

7.1. QSEVEN Connector (J1)

The QSEVEN connector is MXM 230-pin connector, with the same pins on both sides:

 Top side: 103 pins are on the left side, 12 pins on the right side

 Bottom side(mirrored): 12 pins are on the left side, 103 pins on the right side

Table 13: QSEVEN Connector Pin Assignment

Pin.No Pin Name (Bottom side row) Pin.No Pin Name (Top side row)

GND

GBE_MDI3-

GBE_MDI2-

GBE_MDI3+

GBE_MDI2+

GBE_LINK100#

GBE_LINK1000#

GBE_MDI1-

GBE_MDI0-

GBE_MDI1+

GBE_MDI0+

GBE_LINK#

GBE_ACT#

GBE_CTREF

SUS_S5#

WAKE#

SUS_S3#

GPO0

PWRBTN#

SLP_BTN# / GPII1

LID_BTN# / GPII0

GND

KEY

GND

PWGIN

BATLOW# / GPII2

RSTBTN#

SATA0_TX+

SATA1_TX+

SATA0_TX-

SATA1_TX-

SATA_ACT#

GND

SATA0_RX+

SATA1_RX+

SATA0_RX-

SATA1_RX-

GND

BIOS_DISABLE# / BOOT_ALT#

SDIO_CLK#

SDIO_CD#

reserved

SDIO_CMD

SDIO_WP

SDIO_PWR#

SDIO_DAT1

SDIO_DAT0

SDIO_DAT3

SDIO_DAT2

reserved

USB_OTG_PEN

GND

HDA_SYNC / I2S_WS

SMB_CLK / GP1_I2C_CLK

HDA_RST# / I2S_RST#

SMB_DAT / GP1_I2C_DAT

HDA_BITCLK / I2S_CLK

SMB_ALERT#

HDA_SDI / I2S_SDI

GP0_I2C_CLK

HDA_SDO / I2S_SDO

GP0_I2C_DAT

THRM#

WDTRIG#

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 29

Pin.No Pin Name (Bottom side row) Pin.No Pin Name (Top side row)

THRMTRIP#

WDOUT

GND

USB_P7- / USB_SSTX0-

USB_P6- / USB_SSRX0-

USB_P7+ / USB_SSTX0+

USB_P6+ / USB_SSRX0+

USB_6_7_OC#

USB_4_5_OC#

USB_P5- / USB_SSTX2-

USB_P4- / USB_SSRX2-

USB_P5+ / USB_SSTX2+

USB_P4+ / USB_SSRX2+

USB_2_3_OC#

USB_0_1_OC#

USB_P3-

USB_P2-

USB_P3+

USB_P2+

USB_VBUS

USB_ID

USB_P1-

USB_P0-

USB_P1+

USB_P0+

GND

eDP0_TX0+ / LVDS_A0+

100

eDP1_TX0+ / LVDS_B0+

101

eDP0_TX0- / LVDS_A0-

102

eDP1_TX0- / LVDS_B0-

103

eDP0_TX1+ / LVDS_A1+

104

eDP1_TX1+ / LVDS_B1+

105

eDP0_TX1- / LVDS_A1-

106

eDP1_TX1- / LVDS_B1-

107

eDP0_TX2+ / LVDS_A2+

108

eDP1_TX2+ / LVDS_B2+

109

eDP0_TX2- / LVDS_A2-

110

eDP1_TX2- / LVDS_B2-

111

LVDS_PPEN

112

LVDS_BLEN

113

eDP0_TX3+ / LVDS_A3+

114

eDP1_TX3+ / LVDS_B3+

115

eDP0_TX3- / LVDS_A3-

116

eDP1_TX3- / LVDS_B3-

117

GND

118

GND

119

eDP0_AUX+ / LVDS_A_CLK+

120

eDP1_AUX+ / LVDS_B_CLK+

121

eDP0_AUX- / LVDS_A_CLK-

122

eDP1_AUX- / LVDS_B_CLK-

123

LVDS_BLT_CTRL / GP_PWM_OUT0

124

GP_1-Wire_Bus / HDMI_CEC

125

GP2_I2C_DAT / LVDS_DID_DAT

126

eDP0_HPD# / LVDS_BLC_DAT

127

GP2_I2C_CLK / LVDS_DID_CLK

128

eDP1_HPD# / LVDS_BLC_CLK

129

CAN0_TX

130

CAN0_RX

131

DP_LANE3+ / TMDS_CLK+

132

USB_SSTX1-

133

DP_LANE3- / TMDS_CLK-

134

USB_SSTX1+

135

GND

136

GND

137

DP_LANE1+ / TMDS_LANE1+

138

DP_AUX+

139

DP_LANE1- / TMDS_LANE1-

140

DP_AUX-

141

GND

142

GND

143

DP_LANE2+ / TMDS_LANE0+

144

USB_SSRX1-

145

DP_LANE2- / TMDS_LANE0-

146

USB_SSRX1+

147

GND

148

GND

149

DP_LANE0+ / TMDS_LANE2+

150

HDMI_CTRL_DAT

151

DP_LANE0- / TMDS_LANE2-

152

HDMI_CTRL_CLK

153

HDMI_HPD#

154

DP_HPD#

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 30

Pin.No Pin Name (Bottom side row) Pin.No Pin Name (Top side row)

155

PCIE_CLK_REF+

156

PCIE_WAKE#

157

PCIE_CLK_REF-

158

PCIE_RST#

159

GND

160

GND

161

PCIE3_TX+

162

PCIE3_RX+

163

PCIE3_TX-

164

PCIE3_RX-

165

GND

166

GND

167

PCIE2_TX+

168

PCIE2_RX+

169

PCIE2_TX-

170

PCIE2_RX-

171

UART0_TX

172

UART0_RTS#

173

PCIE1_TX+

174

PCIE1_RX+

175

PCIE1_TX-

176

PCIE1_RX-

177

UART0_RX

178

UART0_CTS#

179

PCIE0_TX+

180

PCIE0_RX+

181

PCIE0_TX-

182

PCIE0_RX-

183

GND

184

GND

185

LPC_AD0 / GPIO0

186

LPC_AD1 / GPIO1

187

LPC_AD2 / GPIO2

188

LPC_AD3 / GPIO3

189

LPC_CLK / GPIO4

190

LPC_FRAME# / GPIO5

191

SERIRQ / GPIO6

192

LPC_LDRQ# / GPIO7

193

VCC_RTC

194

SPKR / GP_PWM_OUT2

195

FAN_TACHOIN / GP_TIMER_IN

196

FAN_PWMOUT / GP_PWM_OUT1

197

GND

198

GND

199

SPI_MOSI

200

SPI_CS0#

201

SPI_MISO

202

SPI_CS1#

203

SPI_SCK

204

MFG_NC4

205

VCC_5V_SB

206

VCC_5V_SB

207

MFG_NC0

208

MFG_NC2

209

MFG_NC1

210

MFG_NC3

211

NC*

212

NC*

213

NC*

214

NC*

215

NC*

216

NC*

217

NC*

218

NC*

219

VCC

220

VCC

221

VCC

222

VCC

223

VCC

224

VCC

225

VCC

226

VCC

227

VCC

228

VCC

229

VCC

230

VCC

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 31

7.2. LVDS Connector (J23)

This connector provides data and power connection between the Carrier Board and the Display. This 30-pin lockable connector contains the LVDS output signals and the power to the LVDS display.

Note: Pin 1 and pin 32 shields and are not included in the table below.

Figure 10: 30-pin LVDS connector

Table 14: 30-pin LVDS connector

Pin Signal Description

2 LVDS_A_DATA[0]- LVDS odd channel 0, minus signal

3 LVDS_A_DATA[0]+ LVDS odd channel 0, plus signal

4 LVDS_A_DATA[1]- LVDS odd channel 1, minus signal

5 LVDS_A_DATA[1]+ LVDS odd channel 1, plus signal

6 LVDS_A_DATA[2]- LVDS odd channel 2, minus signal

7 LVDS_A_DATA[2]+ LVDS odd channel 2, plus signal

8 GND Ground

9 LVDS_A_CLK- LVDS odd channel clock, minus signal

10 LVDS_A_CLK+ LVDS odd channel clock, plus signal

11 LVDS_A_DATA[3]- LVDS odd channel 3, minus signal

12 LVDS_A_DATA[3]+ LVDS odd channel 3, plus signal

13 LVDS_B_DATA[0]- LVDS even channel 0, minus signal

14 LVDS_B_DATA[0]+ LVDS even channel 0, plus signal

15 GND Ground

16 LVDS_B_DATA[1]- LVDS even channel 1, minus signal

17 LVDS_B_DATA[1]+ LVDS even channel 1, plus signal

18 GND Ground

19 LVDS_B_DATA[2]- LVDS even channel 2, minus signal

20 LVDS_B_DATA[2]+ LVDS even channel 2, plus signal

21 LVDS_B_CLK- LVDS even channel clock, minus signal

22 LVDS_B_CLK+ LVDS even channel clock plus signal

23 LVDS_B_DATA[3]- LVDS even channel 3, minus signal

24 LVDS_B_DATA[3]+ LVDS even channel 3, plus signal

25 GND Ground

26 I2C_LCD_DATA EDID data signal

27 LVDS_Strap LVDS STRAP signal

28 I2C_LCD_CLK EDID clock signal

29 V_TFT Flat panel power supply (3.3 V or 5V)

30 V_TFT Flat panel power supply (3.3 V or 5V)

31 V_TFT Flat panel power supply (3.3 V or 5V)

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 32

7.3. Backlight Connector (J32)

Figure 11: 7-pin Backlight Connector

Table 15: 7-pin Backlight Connector

Pin Signal Type

1 NC NC

2 Backlight Brightness 5V or 3.3V (jumper selection J24) PWM (0%

- 100%)

Out (27.4 Ohm series resistor)

3 GND Ground

4 V_BKLT - 12V or 5.0V (jumper selection J25) Power

5 V_BKLT - 12V or 5.0V (max. 12W continuous, inrush limited with

U36 or U35)"

Power

6 GND Ground

7 Backlight enable (0 V: off; 5 V or 3 V3: on ) Out (27.4 Ohm series resistor)

7.4. Dual Stacked DP Connector (Display Port) (J2)

The connector provides DP signals from the QSEVEN board as an option on LVDS pins.

Figure 12: Dual Stacked DP Connector

Table 16: Dual Stacked DP Connector

Pin Signal Description

1 OUT ML_Lane0+_TOP

2 GND GND_P2

3 OUT ML_Lane0-_TOP

4 OUT ML_Lane1+_TOP

5 GND GND_P5

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 33

Pin Signal Description

6 OUT ML_Lane1-_TOP

7 OUT ML_Lane2+_TOP

8 GND GND_P8

9 OUT ML_Lane2-_TOP

10 OUT ML_Lane3+_TOP

11 GND GND_P11

12 OUT ML_Lane3-_TOP

13 CONFIG CONFIG1_TOP

14 CONFIG CONFIG2_TOP

15 I/O AUX_CH+_TOP

16 GND GND_P16

17 I/O AUX_CH-_TOP

18 IN HOT_PLUG_TOP

19 GND RETURN_TOP

20 PWR DP_PWR_TOP

21 OUT ML_Lane0+_BOT

22 GND GND_P2

23 OUT ML_Lane0-_BOT

24 OUT ML_Lane1+_BOT

25 GND GND_P5

26 OUT ML_Lane1-_BOT

27 OUT ML_Lane2+_BOT

28 GND GND_P8

29 OUT ML_Lane2-_BOT

30 OUT ML_Lane3+_BOT

31 GND GND_P11

32 OUT ML_Lane3-_BOT

33 CONFIG CONFIG1_BOT

34 CONFIG CONFIG2_BOT

35 I/O AUX_CH+_BOT

36 GND GND_P16

37 I/O AUX_CH-_BOT

38 IN HOT_PLUG_BOT

39 GND RETURN_BOT

40 PWR DP_PWR_BOT

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 34

7.5. HDMI connector (J4)

Figure 13: 19-pin HDMI connector

Table 17: 19-pin HDMI connector

Pin Signal

1 TMDS Data2+

2 TMDS Data2 Shield

3 TMDS Data2−

4 TMDS Data1+

5 TMDS Data1 Shield

6 TMDS Data1−

7 TMDS Data0+

8 TMDS Data0 Shield

9 TMDS Data0−

10 TMDS Clock+

11 TMDS Clock Shield

12 TMDS Clock-

13 CEC

14 Reserved / Utility

15 SCL

16 SDA

17 DDC/CEC Ground

18 +5V Power

19 Hot Plug Detect

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 35

7.6. DP connector (J3)

Figure 14: 20-pin DP connector

Table 18: 20-pin DP connector

Pin Signal Pin Signal

ML LANE 0+

GND (ML LANE 0)

ML LANE 0-

ML LANE 1+

GND (ML LANE 1)

ML LANE 1-

ML LANE 2+

GND (ML LANE 2)

ML LANE 2-

ML LANE 3+

GND (ML LANE 3)

ML LANE 3-

AUX_SEL#

Pull-down to GND

AUX CH+

GND (AUX CH)

Hot Plug

Hot plug

GND (GND_DDC)

+3.3V (DDC EEPROM power) Max 500mA

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 36

7.7. Mini PCIe Card Socket 0 (J45) & Mini PCIe Card Socket 1 (J46)

Figure 15: 52-pin Mini PCIe Card

Table 19: 52-pin Mini PCIe Card

Pin Signal Pin Signal

1 WAKE# 2 +3.3V_S5

3 N.C. 4 GND

5 N.C. 6 +1.5V_S0

7 CLKREQ# 8 UIM-PWR

9 GND 10 UIM-DATA

11 PCIe_REFCLK- 12 UIM-CLK

13 PCIe_REFCLK+ 14 UIM-RST

15 GND 16 UIM-SPU

17 UIM-IC - 18 GND

19 UIM-IC + 20 W_DISABLE1#

21 GND 22 PLTRST#

23 PCIe_RX- 24 +3.3V_S5

25 PCIe_RX+ 26 GND

27 GND 28 +1.5V_S0

29 GND 30 PU3.3V(S5) (Optional: SMB_CLK)

31 PCIe_TX- 32 PU3.3V(S5) (Optional: SMB_DAT

33 PCIe_TX+ 34 GND

35 GND 36 USB_D-

37 GND 38 USB_D+

39 +3.3V_S5 40 GND

41 +3.3V_S5 42 PU 3.3V(S5)

43 GND 44 PU 3.3V(S5)

45 N.C. 46 PU 3.3V(S5)

47 N.C. 48 +1.5V_S0

49 N.C. 50 GND

51 W_DISABLE2# 52 +3.3V_S5

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 37

8.8. SIM card socket (J53)

Figure 16: 8-pin SIM card socket

Table 20: 8-pin SIM card socket

Pin Signal

1 UIM_PWR

2 UIM_RST

3 UIM_CLK

4 UIM_IC + / NC

5 GND

6 UIM_VPP / NC

7 UIM_DATA

8 UIM_IC - / NC

7.9. PCIe x1 connectors (J40, J41)

Figure 17: 52-pin PCIe x1 connector

Table 21: 52-pin PCIe x1 connector

Pin Signal Pin Signal

A1 PRSNT1# B1 V_12V0_S0

A2 V_12V0_S0 B2 V_12V0_S0

A3 V_12V0_S0 B3 V_12V0_S0

A4 GND B4 GND

A5 JTAG2_TCK B5 SMCLK

A6 JTAG3_TDI B6 SMDAT

A7 JTAG4_TDO B7 GND

A8 JTAG5_TMS B8 V_3V3_S0

A9 V_3V3_S0 B9 JTAG1_TRST#

A10 V_3V3_S0 B10 V_3V3_S5

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 38

Pin Signal Pin Signal

A11 PERST# B11 WAKE#

A12 GND B12 RSVD – N.C.

A13 REFCLK+ B13 GND

A14 REFCLK- B14 PET0+

A15 GND B15 PET0-

A16 PER0+ B16 GND

A17 PER0- B17 PRSNT2#

A18 GND B18 GND

7.10. Mini SATA Card Socket (J54)

Figure 18: 52-pin SATA Card Socket

Table 22: 52-pin SATA Card Socket

Pin Signal Pin Signal

1 WAKE# 2 +3.3V_S5

3 NC 4 GND

5 NC 6 +1.5V_S0

7 NC 8 UIM-PWR

9 GND 10 UIM-DATA

11 NC 12 UIM-CLK

13 NC 14 UIM-RST

15 GND 16 UIM-VPP

17 NC 18 GND

19 NC 20 W_DISABLE#

21 GND 22 PLTRST#

23 SATA_RX+ 24 +3.3V_S5

25 SATA_RX- 26 GND

27 GND 28 +1.5V_S0

29 GND 30 PU 3.3V(S5) (Optional:SMB_CLK)

31 SATA_TX- 32 PU 3.3V(S5) (Optional:SMB_DAT)

33 SATA_TX+ 34 GND

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 39

7.11. SATA Connector (J55)

Figure 19: SATA Connector

Table 23: SATA Connector

Pin Signal

1 GND

2 SATA_RDRV_TX1_+

3 SATA_RDRV_TX1_-

4 GND

5 SATA_RDRV_RX1_-

6 SATA_RDRV_RX1_+

7 GND

7.12. Audio Connector Line In & Out (J38 & J39)

Figure 20: Audio Jacks

Table 24: Audio Jacks Pin Assignment (Line Out, green)

Pin Signal

1 Audio GND

2 Line Out Left

3 Line Out Sense

4 Audio GND

5 Line Out Right

Table 25: Audio Jacks Pin Assignment (Line In, blue)

Pin Signal

1 Audio GND

2 Line In Left

3 Line In Sense

4 Audio GND

5 Line In Right

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 40

7.13. Audio Connector (J36)

Figure 21: 9-pin Audio Connector Header

Table 26: 9-pin Audio Connector Header

Pin Signal Pin Signal

1 MIC_L 2 AGND

3 MIC_R 4 PRESENCE#

5 LINE_R 6 MIC_JD

7 - SENSE 8 -

9 LINE_L 10 LINE_JD

7.14. RTC battery holder (J65)

Figure 22: RTC battery holder

Table 27: RTC battery holder

Pin Signal

Positive (+) V_BAT_INT

Negative (-) GND

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 41

7.15. USB 2.0 OTG Connector (J22)

Figure 23: µUSB 2.0 OTG Connector

Table 28: µUSB 2.0 OTG Connector

Pin Signal

1 +5 V USB output (500 mA max.)

2 USB Data -

3 USB Data +

4 ID

5 Ground

7.16. USB Hub Connections (J34)

Connector J34 implements an industry standard USB dual Type A host connection. The USB ports are direct from the CPU. The hub upstream port is connected to the ULP-COM Module USB1 port.

Figure 24: USB 2.0 / 3.0 socket

Table 29 : USB 3.0 Pin Assignment

Pin Type Signal Note

1 PWR 5 V / SB 5 V USB2.0 / 3.0

2 IO USB 3- USB2.0 / 3.0

3 IO USB 3+ USB2.0 / 3.0

4 PWR GND USB2.0 / 3.0

5 IO RX 2 - USB3.0

6 IO RX 2 + USB3.0

7 PWR GND USB3.0

8 IO TX 2- USB3.0

9 IO TX 2+ USB3.0

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 42

Table 30 : USB 3.0 Pin Description

Signal Description

USBn+ USBnRXn+ RXnTXn+ TXn-

Differential pair works as serial differential receive/transmit data lines. (n= 0,1,2,3)

5 V / SB5 V 5 V supply for external devices.

SB5 V is supplied during power-down to allow wakeup on USB device activity. Protected by resettable 1.5 A fuse covering both USB ports.

For HiSpeed rates it is required to use a USB cable, which is specified in USB2.0 standard:

Figure 29: USB 2.0 High Speed Cable

For SuperSpeed rates it is required to use a USB cable, which is specified in USB3.0 standard:

Figure 30: USB 3.0 High Speed Cable

Filler, optional

Braid

Power

SDP Signal Pair

Ground

Jacket

SDP Signal Pair

UTP Signal Pair

On-Twisted Power Pair: Red: VBUS

Black: Power Ground

Outer Shield ≥ 65% Interwoven Tinned Copper Braid

Inner Shield Aluminum Metallized Polyester

Twisted Signaling Pair: White: DGreen: D+

Polyvinyl Chloride (PVC) Jacket

28 AWG Tinned Copper Drain Wire

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 43

7.17. Double USB 3.0 Connector (J34)

This connector provides two USB 3.0 connections (downstream). The 5 V output is electronically fused to 1000 mA each port.

Figure 25: Double USB 3.0 Connector

Table 31: Double USB 3.0 Connector

Pin Signal Remark

1 VBUS +5V (900mA max.) Low, Full & High Speed (USB 2.0) contact pins

Bottom con.

2 USB Data -

3 USB Data +

4 GND

5 USB SSRX- Super Speed (USB3.0) contact pins Bottom con.

6 USB SSRX+

7 GND

8 USB SSTX-

9 USB SSTX+

10 VBUS +5V (900mA max.) Low, Full & High Speed (USB 2.0) contact pins

Top con.

11 USB Data -

12 USB Data +

13 GND

14 USB SSRX- Super Speed (USB3.0) contact pins Top con.

15 USB SSRX+

16 GND

17 USB SSTX-

18 USB SSTX+

Shield Shield

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 44

7.18. LAN Connector (J33)

This connector provides an isolated Ethernet 1000Base-T port, which is connected to an on-board LAN Controller. The galvanic isolated transformers (1500 Vrms, Voltage Regulator Module (VRM)) are integrated in the LAN connectors.

Figure 26: LAN Connector

Table 32: LAN Connector

Pin Signal Pin Signal

1 MDI0+ 2 MDI0-

3 MDI1+ 4 MDI1-

5 CTREF 6 CTREF

7 MDI2+ 8 MDI2-

9 MDI3+ 10 MDI3-

11 Green (A) / Yellow (C) 12 Green (C) / Yellow (A)

13 Green (A) / Yellow (C) 14 Green (C) / Yellow (A)

Table 33: LAN Left LEDs State

Left LED State Link Activity State

Off Link not active

Green (constant on) Link active

Green (flashing) Link active plus activity

Table 34: LAN Right LEDs State

Right LED State Link Speed

Off 10 Base-T

Green (constant on) 100 Base-T

Green (flashing) 1000 Base-T

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 45

7.19. Micro-SD Card Connector (J56)

Figure 27: Micro-SD Card Connector

Table 35: Micro-SD Card Connector

Pin Signal

1 SD_DAT[2]

2 CD / SD_DAT[3]

3 CMD

4 VDD

5 SD_CLK

6 GND / VSS

7 SD_DAT[0]

8 SD_DAT[1]

9 CD_DETECT

10 CD_GND

11 SH_GND

12 SH_GND

13 SH_GND

14 SH_GND

7.20. COM Connector (J58)

Figure 28: COM Connector

Table 36: COM Connector

Pin Signal Direction

1. N.C.

2 RXD (Receive Data) In

3 TXD (Transmit Data) Out

4 N.C.

5 GND

6 N.C.

7 RTS# (Request to Send) Out

8 CTS# (Clear to Send) In

9 N.C

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 46

7.21. CAN Connector (J57)

Figure 29: CAN Connector

Table 37: CAN Connector

Pin Signal

1 CAN0_L

2 CAN0_H

3 V_5V0

4 GND

7.22. LPC/GPIO Header (J59)

Figure 30: LPC/GPIO Header

Table 38: LPC/GPIO Header

Pin Signal Pin Signal

1 GPIO4/LPC_CLK 2 GND

3 GPIO5/LPC_FRAME# 4 N.C.

5 LPC_RST# 6 VCC 5.0V

7 GPIO3/LPC_AD3 8 GPIO2/LPC_AD2

9 VCC 3.3V 10 GPIO1/LPC_AD1

11 LPC_AD0 12 GND

13 SMB_CLK_GP1_I2C_CLK 14 SMB_DAT_GP1_I2C_DAT

15 VCC 3.3V 16 LPC_SERIRQ

17 GND 18 N.C.

19 GPO(SUS STAT#) 20 LPC_LDRQ#

NOTE: SUS_STAT# is changed to GPO0 in Qseven Spec V2.1

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 47

7.23. Power Management Header (J62)

Figure 31: Power Management Header

Table 39: Power Management Header

Pin Signal Pin Signal

1 VCC 1.8V 2 VCC 3.3V

3 PWGIN 4 SUS_S3#

5 GPO0(SUS_STAT#) 6 SLP_BTN#

7 LID_BTN# 8 PWRBTN#

9 PLT_RST# 10 RSTBTN#

11 BATLOW# 12 GP0_I2C_DAT

13 GP0_I2C_CLK 14 SMB_ALERT#

15 GND 16 GND

NOTE: SUS_STAT# is changed to GPO0 in Qseven Spec V2.1

7.24. SYS Signals Header (J37)

Figure 32: SYS Signals Header

Table 40: SYS Signals Header

Pin Signal Pin Signal

1 GP0_I2C_CLK 2 GP0_I2C_DAT

3 SMB_CLK_GP1_I2C_CLK 4 SMB_DAT_GP1_I2C_DAT

5 WDTRIG# 6 SMB_ALERT#

7 WDOUT 8 N.C.

9 GND 10 GND

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 48

7.25. Thermal Header (J66)

Figure 33: Thrm Header

Table 41: Thrm Header

Pin Signal

1 THRM#

2 THRMTRIP#

7.26. CPU Fan (J60)

Figure 34: 4-pin CPU Fan Connector

Table 42: 4-pin CPU Fan Connector

Pin Signal Description

1 GND GND

2 V_CPU_FAN_S0 12 V by default. Can optionally be changed to 5 V, via

jumper H16 setting.

3 CPU_FAN_TACHOIN CPU FAN-Tacho signal

4 CPU_FAN_PWM_CTRL PWM output for FAN

control

7.27. SYS Fan (J61)

Figure 35: 3-pin SYS Fan Connector

Table 43: 3-pin SYS Fan Connector

Pin Signal Description

1 SYS_FAN_TACHOIN System FAN-Tacho signal

2 V_SYS_FAN_S0 12 V by default. Can optionally be changed to 5 V, via

jumper H14 setting.

3 GND GND

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 49

7.28. Power-In Connector (J21)

Figure 36: Power-In Connector

Table 44: Power-In Connector

Pin Signal Description

1 V_12V0_IN_CON Main power input for either both module and carrier (default), or

for carrier only, when J64 is used.

2 GND

The board can be supplied via the AC/DC adapter plugged into the power jack. Such adapters have usually no connection to protective earth. Consequently, the potential of the conductive parts on the board may drift. If a human touches such a part, this may lead to an electric shock. The board must be grounded separately, if the unit is supplied via power jack.

7.29. Module Power-In Connector (J64)

Figure 37: Module Power-In Connector

Table 45: Module Power-In Connector

Pin Signal Description

V_MOD_EXT_CON

Module Power from 3.0 V to 5.25 V is independent from Carrier power.

2 GND

3 N.C. Not connected

4 GND

To power the Qseven Module the power can be set to Ext/Int power by populating one of the following resistors.

 R468 – V_MOD_IN from internal (V_5V0_S5) [Default setting]

 R467 – V_MOD_IN from external (V_3V0-5V25_IN)

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 50

Location of R468 (V_5V0_S5) the default setting

Location of R467 (V_3V0-5V25_IN)

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 51

7.30. ATX 24 Pin Connector (J20)

Figure 38: ATX 24 Pin Connector

Table 46: ATX 24 Pin Connector

Pin Signal Pin Signal

1 V_3V3_ATX_S0 13 V_3V3_ATX_S0

2 V_3V3_ATX_S0 14 V_3V3_ATX_S0

3 GND 15 GND

4 V_5V0_ATX_S0 16 PS_ON#

5 GND 17 GND

6 V_5V0_ATX_S0 18 GND

7 GND 19 GND

8 PG_ATX 20 N.C.

9 V_5V0_SB_ATX 21

V_5V0_ATX_S0

10 V_12V0_ATX_S0 22

V_5V0_ATX_S0

11 V_12V0_ATX_S0 23

V_5V0_ATX_S0

12 V_3V3_ATX_S0 24 GND

7.31. Button Switch (SW1,SW2,SW3,SW4)

Figure 39: Button Switch

Table 47: Reset Button (SW1, J12)

Pin Signal

1 PWRBTN#

2 PWRBTN#

3 GND

4 GND

5 SHIELD

Table 48: Power Button (SW2, J13)

Pin Signal

1 RSTBTN#

2 RSTBTN#

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 52

3 GND

4 GND

5 SHIELD

Table 49: Sleep Button (SW3, J15)

Pin Signal

1 SLP_BTN#

2 SLP_BTN#

3 GND

4 GND

5 SHIELD

Table 50: Lid Button (SW4, J16)

Pin Signal

1 LID_BTN#

2 LID_BTN#

3 GND

4 GND

5 SHIELD

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 53

7.32. Jumpers

7.32.1. Boot Alternate Jumper (J14)

There is a Jumper for Boot Alternate according to the QSEVEN 2.1 specification.

Table 51: Boot Alternate Jumper (J14)

Configuration J14 Jumper Setting Boot Source

1 1-2 Boot from Carrier SPI Flash

2 N.C. Boot from Module SPI Flash (Default)

The BIOS does not support being split between two chips. Booting takes place either from the module SPI or from the baseboard SPI.

7.32.2. Display Power Select Jumper (J24)

Table 52: Display Power Select Jumper (J24)

Jumper Position Function Description

1-2 LVDS Panel Voltage = 5V

2-3 LVDS Panel Voltage = 3.3V (Default)

7.32.3. Backlight Power of the Select Jumper (J25)

Table 53: Backlight Power Select Jumper (J25)

Jumper Position Function Description

1-2 Backlight Voltage = 5V

2-3 (Default) Backlight Voltage = 12V

7.32.4. Dual DP/LVDS Select Jumper (J26)

Table 54: Dual DP/LVDS Select Jumper (J26)

Jumper Position Function Description

1-2 (Default) Dual Display Port

2-3/NC LVDS

7.32.5. Dual DP++/HDMI Select Jumper (J27)

Table 55: Dual DP++/HDMI Select Jumper (J27)

Jumper Position Function Description

1-2 (Default) Display Port++

2-3/NC HDMI

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 54

7.32.6. Audio Channel Jumper for I2S or HDA (J35)

Table 56: Audio Channel Jumper for I2S or HDA (J35)

Jumper Position Function Description

1-2 I2S Codec

NC (Default) HDA codec

7.32.7. mPCIe-0WLAN Disable Jumper (J5,J6)

Table 57: mPCIe-0WLAN Disable Jumper (J5,J6)

Jumper Position Function Description

Open (Default) WLAN in mPCIe slot J45 active

Close WLAN in mPCIe slot J45 inactive

7.32.8. mPCIe-1WLAN Disable Jumper (J7,J8)

Table 58: mPCIe-1WLAN Disable Jumper (J7,J8)

Jumper Position Function Description

Open (Default) WLAN in mPCIe slot J46 active

Close WLAN in mPCIe slot J46 inactive

7.32.9. microSD Write Protect Jumper (J9)

Table 59: microSD Write Protect Jumper (J9)

Jumper Position Function Description

1-2 microSD Write Protect Enable

NC (Default) microSD Write Protect Disable

7.32.10. CAN Bus Termination Jumper (J10)

Table 60: CAN Bus Termination Jumper (J10)

Jumper Position Function Description

1-2 (Default) CAN Bus Termination Enable

NC CAN Bus Termination Disable

7.32.11. LPC/GPIO Selection Jumper (J11)

Table 61: LPC/GPIO Selection Jumper (J11)

Jumper Position Function Description

1-2 (Default) GPIO to Header

NC LPC to Header

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 55

7.32.12. CPU Fan Power Selection Jumper (J30)

Table 62: CPU Fan Power Selection Jumper (J30)

Jumper Position Function Description

1-2 V_CPU_FAN_S0 = 5V

2-3 (Default) V_CPU_FAN_S0 = 12V

7.32.13. SYS Fan Power Selection Jumper (J29)

Table 63: SYS Fan Power Selection Jumper (J29)

Jumper Position Function Description

1-2 V_SYS_FAN_S0 = 5V

2-3 (Default) V_SYS_FAN_S0 = 12V

7.32.14. SYS Fan PWM Control Selection Jumper (J18)

Table 64: SYS Fan PWM Control Selection Jumper (J18)

Jumper Position Function Description

1-2 (Default) System Fan without PWM control

NC System Fan with PWM control

7.32.15. ATX PSU Control Selection Jumper (J28)

Table 65: ATX PSU Control Selection Jumper (J28)

Jumper Position Function Description

1-2 (Default)

ATX PSU is controlled by SUS_S3#

2-3 ATX PSU is controlled by SUS_S5#

7.32.16. ATX PSU ON Selection Jumper (J17)

Table 66: ATX PSU ON Selection Jumper (J17)

Jumper Position Function Description

1-2 Force ATX PSU to ON

NC (Default) ATX PSU is controlled by module

7.32.17. LEDs Enable Jumper (J19)

Table 67: LEDs Enable Jumper (J19)

Jumper Position Function Description

1-2 (Default) Enable LEDs

NC Disable LEDs

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 56

7.32.18. RTC Jumper (J31)

Table 68: RTC Jumper (J31)

Jumper Position Function Description

1-2 (Default) Module RTC powered by Battery (J65)

2-3 Module RTC powered by Super Cap (C367)

7.32.19. Module Standby Voltage (J67)

Table 69: Module Standby Voltage (J67

Jumper Position Function Description

1-2 (Default)

Enable V-5V0_SB for module

NC Disable V-5V0_SB for module

7.32.20. TACHOIN CPU Fan/SYS Fan (J68)

Table 70: TACHOIN CPU Fan/SYS Fan (J68)

Jumper Position Function Description

1-2 (Default)

TACHOIN from CPU FAN

NC (Default) TACHOIN from SYS FAN

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 57

Appendix A: List of Acronyms

Table 71: List of Acronyms

BIOS Basic Input Output System

BSP Board Support Package

CAN Controller-area network

Carrier Board

Application specific circuit board that accepts a COM Express ® module

COM Computer-on-Module

COP Computer Operating Properly

DDI Digital Display Interface –

DDIO Digital Display Input/Output

DIMM Dual In-line Memory Module

DP DisplayPort

(digital display interface standard)

DRAM Dynamic Random Access Memory

DVI Digital Visual Interface

EAPI Embedded Application Programming

Interface

ECC Error Checking and Correction

EEPROM Electrically Erasable Programmable

Read-Only Memory

eDP Embedded Display Port

EMC Electromagnetic Compatibility (EMC)

ESD Electro Sensitive Device

FAT File Allocation Table

FIFO First In First Out

FRU Field Replaceable Unit

Gb Gigabit

GBE Gigabit Ethernet

GPI General Purpose Input

GPIO General Purpose Input Output

GPO General Purpose Output

GPU Graphics Processing Unit

HBR2 High Bit rate 2

HDA High Definition Audio (HD Audio)

HD/HDD Hard Disk /Drive

HDMI High Definition Multimedia Interface

HPM SGET Hardware Platform Management

specification family

HWM Hardware Monitor

IC Integrated Circuit

I2C Inter integrated Circuit Communications

IOT Internet of Things

ISA Industry Standard Architecture

LAN Local Area Network

LPC Low Pin-Count Interface:

LVDS Low Voltage Differential Signaling –

M.A.R.S. Mobile Application for Rechargeable

Systems

MTBF Mean Time Before Failure

NA Not Available

NC Not Connected

NCSI2 Network Communications Services

Interface

NTC Negative Temperature Coefficient

resistor

PCI Peripheral Component Interface

PCIe PCI-Express

PEG PCI Express Graphics

SGET® PCI Industrial Computer Manufacturers

Group

PHY Ethernet controller physical layer

device

Pin-out Type

QSEVEN® definitions for signals on QSEVEN® Module connector pins.

PSU Power Supply Unit

RoHS Restriction of the use of certain

Hazardous Substances

RTC Real Time Clock

SAS Serial Attached SCSI2 – high speed

serial version of SCSI2

SATA Serial AT Attachment:

SMB System Management Bus

SoC System on a Chip

SPI Serial Peripheral Inteface

TPM Trusted Platform Module

UART Universal Asynchronous Receiver

Transmitter

UEFI Unified Extensible Firmware Interface

UHD Ultra High Definition

USB Universal Serial Bus

VGA Video Graphics Adapter

WDT Watch Dog Timer

WEEE Waste Electrical and Electronic

Equipement ( directive)

QSEVEN-Eval Carrier - Rev. 1.1

www.kontron.com // 58

About Kontron

Kontron is a global leader in embedded computing technology (ECT). As a part of technology group S&T, Kontron offers a combined portfolio of secure hardware, middleware and services for Internet of Things (IoT) and Industry

4.0 applications. With its standard products and tailor-made solutions based on highly reliable state-of-the-art embedded technologies, Kontron provides secure and innovative applications for a variety of industries. As a result, customers benefit from accelerated time-to-market, reduced total cost of ownership, product longevity and the best fully integrated applications overall. For more information visit: www.kontron.com



Global Headquarters

Kontron S&T AG

Lise-Meitner-Str. 3-5 86156 Augsburg Germany Tel.: +

49 821 4086-0

Fax: +

49 821 4086-111

info@kontron.com

Kontron Qseven-Eval Carrier User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual