Kontron nanoETXexpress User Manual

Kontron User’s Guide
nanoETXexpress Evaluation Board
Document Revision 0.10_Preliminary
This page intentionally left blank
Table of Contents
Table of Contents
1 User Information ........................................................................................................ 5
1.1 About This Document ......................................................................................... 5
1.2 Copyright Notice ............................................................................................... 5
1.3 Trademarks ...................................................................................................... 5
1.4 Standards ........................................................................................................ 5
1.5 Warranty ......................................................................................................... 5
1.6 Technical Support .............................................................................................. 6
2 Specifications ............................................................................................................ 7
2.1 Mechanical Specifications ................................................................................... 7
2.2 Environmental Specifications .............................................................................. 9
2.2.1Temperature ..................................................................................................... 9
2.2.2Humidity ......................................................................................................... 9
3 Short description ....................................................................................................... 10
4 Block Diagram ........................................................................................................... 11
5 Connector locations ................................................................................................... 13
6 Connector and feature description ............................................................................... 16
6.1 COMexpress connector (J36) ............................................................................. 16
6.2 ATX Power Connector (J15, J22) ......................................................................... 17
6.3 Power, Reset & PS_ON Override (SW1, SW2, J14, J40, J42) ...................................... 18
6.4 Status LEDs & POST Code Display ........................................................................ 19
6.5 SATA (J29, J30, J32, J34) ................................................................................. 20
6.6 USB (J7, J23) ................................................................................................. 21
6.7 USB Client (J3) ............................................................................................... 22
6.8 Ethernet (J10) ................................................................................................ 23
6.9 High Definition Audio (J2, J4, J5, J8, J11, J12) .................................................... 24
6.10 VGA & LVDS (J6, J33) ....................................................................................... 25
6.11 TV-Out (J28, J31) ............................................................................................ 26
6.12 Kontron Feature Connector (J37) ....................................................................... 27
6.13 PCIexpress (J25, J26, J27, U31 and Status LEDs) ................................................... 29
6.14 PCI (J38, J39, U38) ......................................................................................... 30
6.15 Express Card (J41, J49) .................................................................................... 31
6.16 SDIO & GPIO (J43, J48) .................................................................................... 32
6.17 LPC-I/O Controller (J21, U53)) .......................................................................... 33
6.17.1LPC-I/O Fan Control (J44, J45) .......................................................................... 34
6.18 LPCI-I/O Parallel and Serial Ports (J9, J13, J24) .................................................... 35
Kontron User's Guide nanoETXexpress Evaluation Board
iii
Table of Contents
Kontron User's Guide nanoETXexpress Evaluation Board
iv
6.19 Backup BIOS (U48, J46) ................................................................................... 36
6.20 CPLD (J47, U44) .............................................................................................. 37
7 Battery Information (BT1) .......................................................................................... 38
8 Security advice .......................................................................................................... 40
9 Limitations .............................................................................................................. 41
10 Appendix A - Product Compatibility .............................................................................. 42
11 Document History ...................................................................................................... 43
1 0BUser Information
Kontron User's Guide nanoETXexpress Evaluation Board
5
1
1.1
1.2
1.3
1.4
1.5
User Information
About This Document
This document provides information about products from Kontron Embedded Modules GmbH and/or its subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every attempt has been made to ensure that the information in this document is accurate, the information contained within is supplied “as-is” and is subject to change without notice.
For the circuits, descriptions and tables indicated, Kontron assumes no responsibility as far as patents or other rights of third parties are concerned.
Copyright Notice
Copyright © 2007 Kontron Embedded Modules GmbH
All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron Embedded Modules GmbH.
DIMM-PC®, PISA®, ETX®, ETXexpress® , X-board®, DIMM-IO® and DIMM-BUS® are trademarks or registered trademarks of Kontron Embedded Modules GmbH. Kontron is trademark or registered trademark of Kontron AG.
Trademarks
The following lists the trademarks of components used in this board.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines
Corp.
Microsoft is a registered trademark of Microsoft Corp.
Intel is a registered trademark of Intel Corp.
All other products and trademarks mentioned in this manual are trademarks of their
respective owners.
Standards
Kontron Embedded Modules GmbH is certified to ISO 9000 standards.
Warranty
This Kontron Embedded Modules GmbH product is warranted against defects in material and workmanship for the warranty period from the date of shipment. During the warranty period, Kontron Embedded Modules GmbH will at its discretion decide to repair or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are observed.
1 0BUser Information
Kontron User's Guide nanoETXexpress Evaluation Board
6
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental specifications or improper installation or maintenance.
Kontron Embedded Modules GmbH will not be responsible for any defects or damages to other products not supplied by Kontron Embedded Modules GmbH that are caused by a faulty Kontron Embedded Modules GmbH product.
1.6 Technical Support
Technicians and engineers from Kontron Embedded Modules GmbH and/or its subsidiaries are available for technical support. We are committed to making our product easy to use and will help you use our products in your systems.
Please consult our Web site at http://www.kontron.com/support
for the latest product documentation, utilities, drivers and support contacts. In any case you can always contact your board supplier for technical support.
2 1BSpecifications
Kontron User's Guide nanoETXexpress Evaluation Board
7
2
2.1
Specifications
Mechanical Specifications
The nanoETXexpress UGM Evaluation Board is 304.8mm x 210.8mm in size and compares to ATX form factor with 12" x 8.3". The maximum height on top is the audio connector J8 with 34,7mm.
2 1BSpecifications
Kontron User's Guide nanoETXexpress Evaluation Board
8
2 1BSpecifications
Kontron User's Guide nanoETXexpress Evaluation Board
9
2.2 Environmental Specifications
2.2.1 Temperature
Operating:
Ambient temperature: 0 to +60 °C
Non-operating: tbd
Storage:
Ambient temperature: tbd
Note: The maximum operating temperature is the maximum measurable temperature on any spot on a baseboards’
surface. You must maintain the temperature according to the above specification.
2.2.2 Humidity
Operating: 10% to 90% (non condensing)
Non operating: 5% to 95% (non condensing)
3 2BShort description
Kontron User's Guide nanoETXexpress Evaluation Board
10
3 Short description
The Kontron nanoETXexpress Evaluation Board is a Type 1 COM Express baseboard compatible to the new nanoETXexpress standard. COM Express Type 2 modules in basic and compact size can also be used without the features of Connector C/D.
Product specifications:
PCIexpress to PCIexpress Switch
PCIexpress to PCI Bridge
Compatible to 10/100Mbit and GBit-Ethernet Modules
2 PCI Slots
1 PCIexpress x16 Slot, electrically x4
1 PCIexpress x16 Slot, electrically x1
1 PCIexpress x1 Slot
Express Card Slot
4 x SATA Ports
LPT and 2 COM Ports
4 USB 2.0/1.1 Ports + 2 onboard USB pin header
USB Client connector
LVDS, VGA and TV output for integrated module graphics
Shared SD Card Interface and GPIO Header
Onboard HD Audio Codec Realtek ALC888
Analog 7.1 Audio, optical Toslink out and digital S/PDIF in & out
Kontron Feature Connector
Front Panel Connector (HDD Act, Reset SW, Power SW)
Port 80 Post Code display and Status LEDs
Onboard reset and power button
4 3BBlock Diagram
Kontron User's Guide nanoETXexpress Evaluation Board
11
4 Block Diagram
4 3BBlock Diagram
Kontron User's Guide nanoETXexpress Evaluation Board
12
5 4BConnector locations
Kontron User's Guide nanoETXexpress Evaluation Board
13
5 Connector locations
5 4BConnector locations
Kontron User's Guide nanoETXexpress Evaluation Board
14
5 4BConnector locations
Kontron User's Guide nanoETXexpress Evaluation Board
15
Summary of all available connectors and interfaces
Connector Description Connector Description
J1 Onboard Speaker Enable/Disable J26 PCIexpress x1 Slot0 (mechanical x16) J2 Optical S/PDIF out (Toslink) J27 PCIexpress x1 Slot1 J3 USB Client J28 Component TV-Out J4 Front Panel Audio Connector J29 SATA2 J5 Digital Microphone In J30 SATA3 J6 VGA J31 Composite and S-Video TV-Out J7 USB Ports 0-3 J32 SATA0 J8 7.1 Analog HD Audio J33 LVDS (JILI)
J9 Combi Connector COM1/COM2 J34 SATA1 J10 RJ-45 Ethernet Port J35 HDD Activity LED connector J11 Electrical S/PDIF Output J36 COMexpress Type1 connector J12 Electrical S/PDIF Input J37 Kontron Feature Connector J13 COM2 J38 PCI Slot 0 J14 ATX_PS_ON Override J39 PCI Slot 1 J15 ATX_12V 4pin Power J40 Power Button connector J16
100MBit / 1GBit Ethernet Switch
J41 ExpressCard Slo
t
J17 J42 Reset Button connector J18 J43 SD I/O Card Interface J19 J44 FAN1 J20 J45 FAN2 J21 Onboard SIO Address Switch J46 Enable/Disable Module BIOS J22 ATX 24pin Main Power J47 CPLD JTAG (for internal use only) J23 USB4 & USB5 pin header J48 GPIO Connector J24 Parallel Port LPT J49 ExpressCard Reset selector J25 PCIexpress x4 Slot (mechanical x16) J52 SPI/LPC Firmware Hub selector (optional)
Active onboard components:
Component Description Status LED Description
BT1 RTC Battery D6 VCC_3V3
SPK1 Onboard Speaker D7 VCC_5V0
SW1 Power Button D8 VCC_5V_SBY SW2 Reset Button D11 VCC_12V_MOD U31 PCIe - PCIe Switch PEX8505 D12 VCC_12V U38 PCIe - PCI Bridge PEX8112 D13 VCC_3V3_SBY U10 HD Audio Codec Realtek ALC888 D14 VCC_1V0 U44 Altera CPLD D15 VCC_1V5 U48 PLCC Socket for LPC BIOS Flash D16 SUS_STA
T
U53 LPC-IO Winbond W83627HF D17 SUS_S3 U57 SPI Flash (optional) D18 SUS_S4 D38 HDD Activity LED D19 SUS_S5 D39 Watchdog Trigger LED D21 THRMTRIP D40 Port80 MSB D32 PCIe x1 Slot1 D41 Port80 LSB D33 PCIe x1 Slot0
D34 XpressCard D35 PCIe-PCI Bridge D36 PCIe Switch Upstream D37 PCIe Switch Fatal Error
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
16
6
6.1
Connector and feature description
This chapter describes naming and layout of all standard connectors, pin outs and functions of onboard pin headers, configuration jumpers and interfaces. Blue marked jumpers shows the default jumper settings.
COMexpress connector (J36)
The standard Type 1 COM Express connector follows the COMexpress specification. Please refer to the specifications or module manuals on http://www.kontron.com
for more details and pin out description.
The Kontron nanoETXexpress Evaluation Baseboard offers the possibility to connect a full featured Type1 module following the new standard form factor nanoETXexpress or to connect a Type2 module like ETXexpress in basic or micro size without the features of the second connector C/D.
The Type1 connection via connector A/B defines following feature set:
Row A Functions Row B Functions
Gigabit Ethernet
LPC
SMB
SATA0, SATA2 SATA1, SATA3
Power Managemen
t
Audio, I2C USB6, USB4 USB2, USB0
USB7, USB5 USB3, USB1
PCIe 0-5 PCIe 0-5
LVDS LVDS GPIO VGA, TVou
t
VCC VCC
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
17
6.2 ATX Power Connector (J15, J22)
Connect the ATX and the ATX_12V power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the module. If the ATX_12V power connector is not connected, the system will not start.
24 pin ATX Power 4 pin ATX_12V
Pin Def Pin Def
1 +3.3VDC 13 +3.3VDC 2 +3.3VDC 14 -12VDC 3 GND 15 GND 4 +5VDC 16 PS_ON 5 GND 17 GND 6 +5VDC 18 GND 7 GND 19 GND 8 PWR_OK 20 -5VDC
9 +5VSB 21 +5VDC 10 +12VDC 22 +5VDC 11 +12VDC 23 +5VDC 12 +3.3VDC 24 GND
Pin Def
1 GND 2 GND 3 +12VDC 4 +12VDC
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
18
6.3 Power, Reset & PS_ON Override (SW1, SW2, J14, J40, J42)
The behavior of power button SW1 and pin header J40 can be configured in BIOS Setup. Refer to the module's manual for more details and possible configurations.
Reset & Power Button PS_ON override J14
Connector Function
J40
Power Button
SW1
J42
Reset Button
SW2
Closed Pins Function
1 - 2 OFF
3 - 4 PS_ON
5 - 6 Always ON
J40 (Power Button) and J42 (Reset Button) are pin header to connect a switch on the chassis front panel. With the manual PS_ON override Jumper J26 you are able to switch the Power Supply on or off manually.
Note: Blue Jumpers and bold marked text shows Kontron default settings
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
19
6.4 Status LEDs & POST Code Display
The onboard status and voltage indicator LEDs will show you the current power states, alarm signals and correct voltage status on the COMexpress module.
LED Description LED Description
D38 HDD Activity LED D6 VCC_3V3 D39 Watchdog Trigger Active D7 VCC_5V0 D40 Port80 MSB D8 VCC_5V_SBY D41 Port80 LSB D11 VCC_12V_MOD
D12 VCC_12V D13 VCC_3V3_SBY D14 VCC_1V0 D15 VCC_1V5 D16 SUS_STAT D17 SUS_S3 D18 SUS_S4 D19 SUS_S5 D21 THRMTRIP
LED D38 shows hard disk activity for connected SATA devices. D40 (Port80 MSB) and D42 (Port80 LSB) shows the actual POST Codes if the module BIOS is configured to send POST Code cycles to the LPC Bus.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
20
6.5 SATA (J29, J30, J32, J34)
The COM Express specification provides 4 SATA channels maximum. Please check how many SATA ports are supported by the used COMexpress module.
SATA Connector Pin out Connector Configuration
Pin Signal
1 GND 2 TX+ 3
T
X­4 GND 5 RX­6 RX+ 7 GND
Connector SATA Port
J29 SATA2 J30 SATA3 J32 SATA0 J34 SATA1
Refer to the COMexpress module manual how to enable and configure SATA.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
21
6.6 USB (J7, J23)
COM Express defines a maximum of 8 USB Ports. On nanoETXexpress Evaluation Baseboard 4 USB Ports (USB0-USB3) are provided via rear panel connector J7 and two (USB4 & USB5) ports via onboard pin header (J23). USB Port 6 is used for Express Card.
J23 Pin out
Pin Description Pin Description
1 VCC USB4 2 VCC USB5 3 USB4- 4 USB5­5 USB4+ 6 USB5+ 7 GND USB4 8 GND USB5 9 Key Pin 10 n.c.
All USB Ports are ESD and over-current protected.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
22
6.7 USB Client (J3)
With nanoETXexpress a new function called USB Client is coming up. If supported by the used chipset on the module, USB Port7 is used as an USB Client connection via MiniUSB Connector TypeA (J3). The client function is a software implemented USB device in the chipset which allows connecting the platform to other USB Host interfaces for purposes of file transfer, network connectivity or any other USB functions.
Refer to the module manual and download section of the used module for driver and software downloads to use USB Client functionality.
Warning: Do not use USB Client Port J3 to connect any USB devices
Note: If Express Card USB function (USB6) and USB Client (USB7) can be used depends on the modules
specification. For the Express Card USB function a module with full USB support is necessary.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
23
6.8 Ethernet (J10)
The Ethernet Port must be configured according to the modules specifications. For Gigabit Ethernet modules close all jumpers J16-J20 (default). For modules with only 10/100MBit connection (e.g. microETXexpress) open all Jumpers.
J10 Ethernet LED function
LED State Function
1 (left)
Green Link1000
Y
ellow Link100
Of
f
Link10
2 (right)
On Link
Blinking Activity
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
24
6.9 High Definition Audio (J2, J4, J5, J8, J11, J12)
The nanoETXexpress Evaluation Baseboard is equipped with a Realtek ALC888 High Definition Audio Codec which supports up to 7.1-channel speaker configuration, optical and digital S/PDIF out, S/PDIF in and digital microphone input.
The optical Toslink S/PDIF Connector (J2) and the coaxial S/PDIF Connector (J12) provides digital audio out. J5 is used for digital microphone connection and J11 for digital S/PDIF in. A standard front panel can be connected via pin header J4.
Pin J4 J5 J12 J11
1 MIC2-L DMIC-CLK SPDIF_OU
T
SPDIF_IN 2 GND DMIC-DATA GND GND 3 MIC2-R (MIC Power) PWR_3.3V - ­4 PRESENCE# GND - ­5 LINE2-R (LineOut-R) - - ­6 MIC2-JD - - ­7 SENSE - - ­8 Key Pin - - ­9 Line2-L (LineOut-L) - - -
10 LINE2-JD - - -
Speaker Configuration J8
J8 2-channel 4-channel 6-channel 8-channel
Orange - - Center/Subwoofer Center/Subwoofer
Black - Rear Speaker Side Speaker Rear Speaker Ou
t
Gray - - - Side Speaker Ou
t
Blue Line In Line In Line In Line In
Green Line Ou
t
Front Speaker Front Speaker Front Speaker
Pink Mic In Mic In Mic In Mic In
Note1: In addition to the default speaker settings, the analog audio Jacks can be reconfigured to perform different
functions via the Realtek HDAudio Driver Software which is available on Kontron website. Only microphones still must be connected to the default pink jack.
Note2: Audio is only working in combination with HD Audio compatible COM Express Modules.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
25
6.10 VGA & LVDS (J6, J33)
The integrated graphics from the ETXexpress module can be used by LVDS connector J33 or the analog DSUB15 VGA connector J6.
LVDS & VGA Pin out
Pin LVDS Signal VGA Signal Pin LVDS Signal
1 LVDS_BKLT_CTRL Red 21 LVDS_B1+ 2 LVDS_A0- Green 22 DETECT# (GND) 3 LVDS_A0+ Blue 23 LVDS_B2­4 ENAVDD NC 24 LVDS_B2+ 5 LVDS_A1- GND1 25 GND 6 LVDS_A1+ AGND1 26 LVDS_B_CK­7 NC AGND2 27 LVDS_B_CK+ 8 LVDS_A2- AGND3 28 GND
9 LVDS_A2+ Key 29 LVDS_B3­10 GND GND2 30 LVDS_B3+ 11 LVDS_A_CK- NC 31 +5V 12 LVDS_A_CK+ ID1 (DDC_DAT) 32 +5V 13 GND HSYNC 33 +5V 14 LVDS_A3- VSYNC 34 +5V 15 LVDS_A3+ ID3 (DDC_CLK) 35 BLON# 16 JILI_DAT - 36 GND 17 LVDS_B0- - 37 GND 18 LVDS_B0+ - 38 +12V 19 JILI_CLK - 39 +12V 20 LVDS_B1- - 40 +12V
For a detailed description of LVDS JILI interface refer to the JILI documentation on Kontron’s webpage.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
26
6.11 TV-Out (J28, J31)
The nanoETXexpress Evaluation Baseboard provides three possible TV-Out connections. Composite Video (Yellow Cinch) and S-Video out are available on connector J31. Component TV-Out is available via pin header J28.
TV-Out connector Pin out
Pin Composite J31 S-Video J31 Component J28
1 FBAS GND_Y Pb (Chrominance) 2 GND GND_C GNDA 3 - Luminanz_Y
Y
(Luminance) 4 - Chrominanz_C GNDB 5 - - Pr (Chrominance) 6 - - GNDC 7 - - GND_VIDEO 8 - - n.c.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
27
6.12 Kontron Feature Connector (J37)
The Feature Connector J37 is a Kontron standard connection for easy communication with external devices for example SM Bus communication with Kontron M.A.R.S. Smart Battery System. See the detailed description of available functions below:
Feature Connector Pin out
Pin Signal Description
1 PWR_+5V 5V power +5V UL-protected with inductor (600R@100MHz, 1A) 2 GPO2 3.3V-O General-purpose power management event outpu
t
3 #BATLOW 3.3V-I
Battery low input. May be driven low by external circuitry to signal that the system battery is low, or may be used to signal some other external power management event.
4 GPI2 3.3V-I General-purpose power management event inpu
t
5 #SYS_RESET 3.3V-I
This input may be driven low by external circuitry in order to reset the power
management logic 6 WDT 3.3V-O Indicating that a Watchdog Timeout Event has occurred 7 LPC_SERIRQ 3.3V-I Serial interrupt request. This pin is used to support the serial interrupt protocol. 8 - - Not connected 9 I2C_DAT 3.3V-IO Data line of I2C-Bus
10 #SMB_ALERT 3.3V-I
System Management Bus Alert input. May be driven low by SMB devices in order to
signal an event on the SM Bus
11 I2C_CLK 3.3V-O Clock line of I2C-Bus 12 SMB_DAT 3.3V-IO
Clock and data line of SM-Bus.
13 SMB_CLK 3.3V-O 14 - - Not connected 15 #WAKE1 3.3V-I Low driven general purpose wake-up signal
16 VCC_RTC 3V-I
3V backup cell input. Should be connected to a 3V backup cell for RTC operation and
storage register non-volatility in the absence of system power. (VBATT = 2.4 – 3.3V)
17 #THRM 3.3V-I Input from off-module temperature sensor indicating an over temperature situation 18 GND GND Ground
19 PWR_OK 3.3V-I
High active input indicating that power from the power supply is ready. It can also be
used as low active reset input signal.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
28
Pin Signal Description
20 GND GND Ground 21 #PWRBTN 3.3V-I Power Button Input. This input is used to support the ACPI Power Button function. 22 GND GND Ground 23 #ATA_ACT 3.3V-O Low active output signal, which indicates activity on IDE interfaces. 24 #CB_RESET 3.3V-O Low active Reset output from module to carrier board
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
29
6.13 PCIexpress (J25, J26, J27, U31 and Status LEDs)
PCIexpress lane0 from the COMexpress module is used to connect a 5-lane PCIexpress Gen1 switch PEX8505AA. The Type 1 connection of the nanoETXexpress Evaluation Board offers a maximum of 5 PCIe lanes from the module (PCIe0 ... PCIE4). The switch provides 4 additional PCIexpress lanes (PCIe5 … PCIe8). See the detailed PCIexpress configuration in the list below.
J25 (PCIexpress x4 Slot) and J26 (PCIexpress x1 Slot0) are mechanical x16 slots to connect x16 PCIexpress cards. The electrical configuration does not match the mechanical:
PCIexpress configuration:
Baseboard PCIe Lane Source Target
#0 COMe Module lane#0 PCIe Switch lane#0 (Uplink) #1 COMe Module lane#1
PCIe x4 slot (J25)
#2 COMe Module lane#2 #3 COMe Module lane#3 #4 COMe Module lane#4 #5 PCIe Switch lane#1 PCIe-PCI Bridge #6 PCIe Switch lane#2 Xpress-Card Slot #7 PCIe Switch lane#3 PCIe x1 Slot0 (J26) #8 PCIe Switch lane#4 PCIe x1 Slot1 (J27)
6 LEDs from the PCIe switch shows the status of PCIexpress. The 'Lane Good LEDs' D32 to D36 provides visual indication that the Physical Layer of the link for each lane is trained to at least x1 width.
LED Function LED Function
D37 Fatal Error in PEX8505 D34 Xpress-Card D36 Upstream link to Module D33 PCIe x1 Slot0 D35 PCIe-PCI Bridge D32 PCIe x1 Slot1
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
30
6.14 PCI (J38, J39, U38)
According to the COMexpress specification PCI usually is provided by connector C/D. On the nanoETXexpress Evaluation Board with Type1 connection PCI must be generated with a PCIexpress to PCI Bridge.
The PCIe-toPCI Bridge PEX8112AA provides a maximum of 4 PCI Slots. PCI Slot0 (J38) and PCI Slot1 (J39) can be used on the nanoETXexpress Evaluation Board.
Note1: If PCIexpress and PCI can be used depends on the modules specification. Please refer to the module
documentation for further details. Appendix A gives a short overview.
Note2: The PCI IO voltage is set to 3,3V and therefore PCI is not compatible to 5V only cards.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
31
6.15 Express Card (J41, J49)
The onboard Express Card is connected to PCIexpress Lane #6 (lane #2 of PCIe Switch) and to USB Port6. To use the Express Card USB functions an ETXexpress module with at least 8 USB Ports is necessary.
Connector J41 allows using both ExpressCard/34 and ExpressCard/54. The maximum continuous Card Power is
1,3A on 3,3V
275mA on Aux Power
650mA on 1,5V
Express Card pin out
Pin Signal Pin Signal
1 GND 14 3.3VS_1 2 USB_D- 15 3.3VS_0 3 USB_D+ 16 CLKREQ# 4 CPUSB# 17 CPPE# 5 NC 18 REFCLK­6 NC 19 REFCLK+ 7 SMB_CLK 20 GND 8 SMB_DATA 21 PERN0
9 1.5V_2 22 PERP0 10 1.5V_1 23 GND_1 11 WAKE# 24 PETN0 12 3.3VAUX 25 PETP0 13 PERST# 26 GND_0
Jumper J49 switches ExpressCard Reset between 'ModuleHotplug' (Closed Jumper, default) and CB_Reset# (Open Jumper)
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
32
6.16 SDIO & GPIO (J43, J48)
COMexpress defines a maximum of 4GPIs and 4 GPOs. With the new nanoETXexpress standard the 8 General Purpose Input/Output signals alternatively can be configured as SDIO interface. Refer to the module's manual if SD Card feature is supported and how to be configured.
A TI74LVCH244A octal buffer provides galvanic isolation between SDIO and GPIO output connectors. J43 is active, if a SD Card is connected (Pin10, Detect).
SDIO & GPIO pin out
Pin SDIO - J43 GPIO - J48
1 CD/DAT3 - Card Detection (GPI3) VCC 3,3V 2 CMD - Command/Response (GPO1) GPO #0 3 VSS1 - Supply Voltage - GND GPI #0 4 VDD - Power Supply - 3,3V GPO #1 5 CLK - Clock (GPO0) GPI #1 6 VSS2 - Supply Voltage - GND GPO #2 7 DAT0 - Data Line 0 (GPI0) GPI #2 8 DAT1 - Data Line 1 (GPI1) GPO #3
9 DAT2 - Data Line 2 (GPI2) GPI #3 10 Detect (GPO3) GND 11 Protect (GPO2) ­12 GND -
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
33
6.17 LPC-I/O Controller (J21, U53))
The nanoETXexpress Evaluation Baseboard is equipped with an external LPC I/O Controller Winbond W83627HFJ to provide standard legacy connections like COM or LPT.
To avoid address conflicts if a Super I/O is present on the COMexpress Module it's possible to switch the Baseboard's Super I/O Address with jumper J25.
SIO address switch J21
Jumper Address
closed 4Eh
open 2Eh
Note: To use the LPC-I/O functions like COM, LPT and hardware monitoring features a Kontron module with legacy
BIOS is necessary.
6 5BConnector and feature description
6.17.1 LPC-I/O Fan Control (J44, J45)
The Winbond 83627HFJ LPC-I/O Controller provides an internal Hardware Monitor and FAN connection.
Fan Connector Pin out
Pin FAN1 FAN2
1 Sense Sense 2 +12V +12V 3 GND GND
Note: To support FAN control and monitoring it is required to set the LPC Decode Range 1 Base to 290h and the
Range 1 Size to 8B in the module BIOS. Refer to the module's manual for more details.
Kontron User's Guide nanoETXexpress Evaluation Board
34
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
35
6.18 LPCI-I/O Parallel and Serial Ports (J9, J13, J24)
For serial DSUB connections use J9 (COM1, COM2) or J13 (COM2) with Kontron Adapter cable KAB-
DSUB9-3. The parallel port can be used with adapter cable KAB-DSUB25-1.
LPT and COM Port pin out
Pin J24 - LPT J9-COM1/2 J13-COM2 Pin LPT COM1/COM2 J13-COM2
1 #STB DCD DCD 2 #AFD DSR DSR 3 PD0 RXD RXD 4 #ERROR RTS RTS 5 PD1 TXD TXD 6 #INI
T
CTS CTS 7 PD2 DTR DTR 8 #SLCTIN RI RI 9 PD3 GND GND 10 GND NC VCC_5V
11 PD4 - - 12 GND - ­13 PD5 - - 14 GND - ­15 PD6 - - 16 GND - ­17 PD7 - - 18 GND - ­19 #ACK - - 20 GND - ­21 BUSY - - 22 GND - ­23 PE - - 24 GND - ­25 SLCT - - 26 n.c. - -
Note: To use the LPC-I/O functions like COM, LPT and hardware monitoring features a Kontron module with legacy
BIOS is necessary.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
36
6.19 Backup BIOS (U48, J46)
The nanoETXexpress Evaluation Baseboard provides a backup LPC Firmware Hub U48. The backup BIOS must be activated with jumper J46.
The yellow marked components are for an optional SPI flash (U57). In case of using an SPI flash jumper J52 must be closed to activate it. A open jumper J52 enables the LPC Firmware Hub U48.
Backup BIOS Disable J46
J69 Active BIOS
Closed Backup BIOS
Open Module BIOS
Updating the baseboard BIOS with booting from the module
Open jumper J46 to boot from the module
Prepare a DOS bootable device with the BIOS to be flashed (e.g. a USB stick)
Boot into DOS
Close jumper J46
Start the flashing command
Updating the module BIOS with booting from the baseboard
Close jumper J46 to boot from the baseboard
Prepare a DOS bootable device with the BIOS to be flashed (e.g. a USB stick)
Boot into DOS
Open jumper J46
Start the flashing command
Note: Only use suitable BIOSes for the regarding product either on the module or the baseboard.
6 5BConnector and feature description
Kontron User's Guide nanoETXexpress Evaluation Board
37
6.20 CPLD (J47, U44)
Current Kontron products are equipped with a Altera CPLD (Complex Programmable Logic Device) for power up sequencing and other functionalities. The nanoETXexpress Evaluation Baseboard's CPLD (U44) can be accessed by connector J47
CPLD J47 Pin out
Pin Signal
1 3,3V 2 TDI 3 TCK 4 TMS 5 TDO 6 MCCI_DATA_OU
T
7 MCC_DATA_IN 8 MCC_RS
T
9 MCCI_CLK
10 MCCI_IN
T
11 MCCI_Freeze 12 GND
Warning: J47 is for internal use only. Do not connect any devices.
7 6BBattery Information (BT1)
Kontron User's Guide nanoETXexpress Evaluation Board
38
7 Battery Information (BT1)
The nanoETXexpress Evaluation Baseboard includes a standard CR2032 3V RTC battery.
English:
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Deutsch:
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben
oder einen vom Hersteller empfohlenen gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
French:
ATTENTION: Risque d‘explosion avec l‘échange inadéquat de la batterie. Replacement seulement par le
même ou un type équivalent recommandé par le producteur. L’évacuation des batteries usagées conformément à des indications du fabricant.
Danish:
ADVARSEL: Lithiumbatteri – Eksplosionsfare ved fejlagtig Håndtering. Udskifting må kun ske med
batteri af samme fabrikant og type. Lever det brugte batteri tilbage til leverandren.
Finnish:
VAROITUS: Paristo voi rãjãhtãã, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaanlaltevalmistajan suosittelmaan tyyppiln. Havita kaytetty paristo valmistajan ohjeiden mukaisesti.
7 6BBattery Information (BT1)
Spanish:
Precaución: Peligro de explosión si la batería se sustituye incorrectamente. Sustituya solamente por el
mismo o tipo equivalente recomendado por el fabricante. Disponga las baterías usadas según las instrucciones del fabricante.
Note: The battery of this product is not considered to be accessible by the end user. Therefore the safety
instructions are only given in English, German, French, Danish, Finish and Spanish language.
If the battery of this product however is accessible by the end user, it is in the responsibility of the
Kontron customer to give the corresponding safety instructions in the required language(s).
Kontron User's Guide nanoETXexpress Evaluation Board
39
8 7BSecurity advice
Kontron User's Guide nanoETXexpress Evaluation Board
40
8 Security advice
To protect the external power lines to peripheral devices the customer has to take care about:
- The wires to the external device have the right diameter to withstand the max. available current
- The housing of the external device fulfils the fire protection requirements of IEC/EN 60950.
9 8BLimitations
Kontron User's Guide nanoETXexpress Evaluation Board
41
9 Limitations
Hardware limitations on PCB rev. L111:
The octal buffer is not able to switch between SDIO and GPIO. SD Card interface is
only working with desoldered buffer and assembled R380. A manual switching via jumper will be implemented in newer designs.
The optional SPI Flash U57/J52 is not supported.
10 9BAppendix A - Product Compatibility
Kontron User's Guide nanoETXexpress Evaluation Board
42
10 Appendix A - Product Compatibility
A short overview which baseboard functions can be used on Kontron COMexpress modules:
USB Client SDIO PCIe 0 (*) PCIe 1-4 GB LAN SATA 0-3 TV-out
nanoETXexpress-SP
-
SATA 0 -
microETXexpress-SP
SATA 0,1 -
microETXexpress-PM
- (**) - - (**) - 10/100 SATA 0,1 -
ETXexpress-PM
- -
PCIe 1
SATA 0,1 -
ETXexpress-CD
- -
PCIe 1,2,3
SATA 0,1
ETXexpress-690
- -
PCIe 1,2
-
ETXexpress-MC
- -
PCIe 1,2,3
SATA 0,1,2
ETXexpress-PC
- -
(*) PCIexpress lane0 support includes PCIexpress x1 Slot0, PCIexpress x1 Slot1, PCIe part of Express-Card and PCI
support.
(**) microETXexpress-PM only supports 6 USB Ports and no PCIexpress whereby XPress-Card has no function.
11 10BDocument History
Kontron User's Guide nanoETXexpress Evaluation Board
43
11 Document History
Rev. Date Edited by Changes
0.10_prelim 08.10.08 PRO Initial Release
Loading...