Kontron CP3-SVE-P200AC User Manual

Download

Page 1

CPCI

Power Supply

Manual

PRODUCT DOCUMENTATION

PD05

CP3-SVE-P200AC

Reference ID: 24139 PD05

Revision: 01

Issued: February 01, 2002

The product described in this manual is in compliance with all applied CE standards.

Page 2

PD05: CP3-SVE-P200AC CPCI Power Supply

Revision History

CPCI Power Supply Manual:

Manual/Product Title:

Reference ID: 24139 PD05

Product Documentation: CP3-SVE-P200AC

Rev.

Index

01 Initial Issue Feb. 01, 2002

Brief Description of Changes Date of Issue

Imprint

Copyright © 2002 PEP Modular Computers GmbH. All rights reserved. This manual may not be copied, photocopied, reproduced, translated or converted to any electronic or machinereadable form in whole or in part without prior written approval of PEP Modular Computers GmbH.

DISCLAIMER:

PEP Modular Computers GmbH rejects any liability for the correctness and completeness of this manual as well as its suitability for any particular purpose.

This manual was realized by: TPD/Engineering, PEP Modular Computers GmbH.

Page 3

CPCI Power Supply PD05: CP3-SVE-P200AC

1. Introduction

The specific product description provided with this product documentation is part of the PEP’s CPCI Power Supply manual. For further information, in particular regarding general details as well as safety and warranty statements, refer to the CPCI Power Supply Manual, ID 24139.

2. 200W P-Type Power Supply Unit

The main features of the 3U P-type, 120V/230V input, 200W output AC/DC power supply unit CP3-SVE-P200AC are described in the following table:

Table 1: Distinctive Features of Power Supply Unit CP3-SVE-P200AC

Feature Specification

Form Factor

Frontpanel Size

Mechanics

Plug-In Compatibility

Power Supply Connector

Input Voltage

Voltage Switching

Output Power

Output Voltages / Currents

Cooling

Redundant Supply Capability

40.6 * 128.7 mm 19” rack Yes Positronic 47-pin connector V = 85V..264V AC

Frequency: 47Hz..63Hz Continuous input range 200W with 250 LFM forced-air cooling V1 = +5V at 40A

V2 = +3.3V at 40A V3 = +12V at 5.5A V4 = -12V at 1.5A

250 LFM forced-air cooling Always

Status Indication

Special Feature(s)

LED’s for input good and power fail Power sharing

Page 4

PD05: CP3-SVE-P200AC CPCI Power Supply

2.1 Mechanical Specifications

Figure 1: View of Power Supply Unit CP3-SVE-P200AC

Page 5

CPCI Power Supply PD05: CP3-SVE-P200AC

Figure 2: Power Supply Dimensions

6.671" (169.4mm)

0.1" (2.54mm)

6.399" (162.5mm)

3U x 8HP

1.6" (40.6mm)

Page 6

PD05: CP3-SVE-P200AC CPCI Power Supply

2.2 Power Supply Connector

Figure 3: Orientation of the Positronic P-47 Power Supply Connector

42 43 44 39

40 41 36 37 38 33 34 35 30 31 32 27 28 29 24 25 26 21 22 23

The V

input voltage to the power supply

unit and the V1 ... V4 output voltages from the power supply unit to the backplane are connected via a 47-pin Positronic male power supply connector.

For the pinouts of the Positronic P-47 power supply connector please refer to the following table.

Page 7

CPCI Power Supply PD05: CP3-SVE-P200AC

Table 2: Positronic 47-Pin Connector Pinout

PIN SIGNAL NAME DESCRIPTION PIN SIGNAL NAME DESCRIPTION

1 - 4 V1 V1 OUTPUT (+5V) 32 NC NOT CONNECTED

5 - 12 RTN V1 and V2 RETURN 33 V2 SENSE V2 REMOTE SENSE

13 - 18 V2 V2 OUTPUT (+3.3V) 34 S RTN SENSE RETURN

19 RTN V3 RETURN 35 V1 SHARE V1 CURRENT SHARE 20 V3 V3 OUTPUT (+12V) 36 V3 SENSE V3 REMOTE S ENSE 21 V4 V4 OUTPUT (-12V) 37 NC NOT CONNECTED 22 RTN SIGNAL RETURN 38 DEG# DEGRADE SIGNAL 23 RESERVED RESERVED 39 INH# INHIBIT 24 RTN V4 RETURN 40 NC NOT CONNECTED 25 NC NOT CONNECTED 41 V2 SHARE V2 CURRENT SHARE 26 RESERVED RESERVED 42 FAL# FAIL SIGNAL 27 EN# ENABLE 43 NC NOT CONNECTED 28 NC NOT CONNECTED 44 V3 SHARE V3 CURRENT SHARE 29 NC NOT CONNECTED 45 CGND CHASSIS GROUND 30 V1SENSE V1 REMOTE SENSE 46 ACN AC INPUT NEUTRAL 31 NC NOT CONNECTED 47 ACL AC INPUT LINE

2.3 Installation

Thanks to its plug-in compatibility this P-type power supply unit allows for an easy installation, by which the power supply unit’s male Positronic 47-pin power connector is inserted into the backplane’s mating female connector without the need of any intermediate adaptation.

Warning!

If this type of power supply is removed for any reason from an operating system, do not reinstall immediately. Wait 1 to 2 minutes before reinstalling. Failure to comply with this may result in an Output Failure indication on the power supply. This is due to an internal protection feature of the power supply which requires ti me to cool down before the power supply is put back into operation.

Page 8

PD05: CP3-SVE-P200AC CPCI Power Supply

2.4 Electrical Specifications

INPUT

PARAMETER CONDITIONS / DESCRIPTION MIN NOM MAX UNITS

Input Voltage - AC Continuous input range. 85 264 VAC Input Frequency 47 63 Hz Hold-up Time 20 ms Input Protection Non-user serviceable, internally-located input line fuse. Inrush Surge Current Internally limited by thermistor and electronic switch. 30 A Operating Frequency Switching frequency of main output transformer. 125 145 kHz

OUTPUT

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Efficiency Full rated load, 115 VAC. 80 % Minimum Load; V1,

V2, V3 Minimum Load, V3 Minimum load on V3 required to maintain regulation on V4. 50% of V4 Load A Ripple and Noise Full load, 20 MHz bandwidth. See Regulation table Output Power 250 LFM forced-air cooling. 200 W Overshoot /

Undershoot Regulation Varies by output. T otal regulation includes: line changes

Turn-on Delay Time required for initial output voltage stabilization. 150 ms Initial Setting Accuracy ±1 %

Minimum load required to maintain regulation with no load on V4.

Output voltage overshoot / undershoot at turn-on. 0 %

over the specified input range, changes in load starting at 50% load and changing to 100% load.

None A

See Regulation table

REGULATION

OUTPUT

VOLTAGE

ADJUSTMENT

RANGE

OUTPUT

CURRENT

LINE

REGULATION

LOAD

REGULATION

RIPPLE & NOISE %pk-pk (NOTE 1)

V1 +5V N/A 40A 0.5% 1% 2% V2 +3.3V N/A 40A 0.5% 1% 2% V3 +12V N/A 5.5A 0.5% 1% 1.3% V4 -12V N/A 1.5A 0.5% 1% 1.3%

Page 9

CPCI Power Supply PD05: CP3-SVE-P200AC

PROTECTION AND CONTROL

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Overvoltage Protection

Overload Protection Fully protected against output overload and short cir-

Overtemperature Protection

Power Fail (FAL#) TTL compatible signal, open collector active low sig-

Current Share Accuracy of shared current with up to 6 parallel units

Remote Sense Available on V1, V2, and V3. Total voltage compensa-

Inhibit (INH#) TTL-compatible signal inhibited with GND or TTL "0". Available Enable (EN#) Contact closure to external ground to start unit. On

Overtemperature Warning (DEG#)

Latch style overvoltage protection. 120 130 %Vnom

Available cuit. Automatic recovery upon removal of overload condition.

System shutdown due to excessive internal temperature, automatic reset.

nal. Indicates any output below 90% and/or a low input <85VAC.

of the same type of power supply. Single wire current share on V1, V2, and V3.

tion for cable losses with respect to the main output.

shortest pin (last make, first break). Provides warning when power supply temperature

exceeds rating. TTL-compatible open.

Available

10 %

150 mV

Front Panel LED Status Indicators

Input OK (Green), Output Failure (Red). In redundant setups, Output Failure may also indicate that there is no main power input to the power supply.

Available

SAFTEY, REGULATORY, AND EMI

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Agency Approvals UL1950, cUL1950, EN60950 (TÜV). Approved Dielectric Withstand

Voltage Electromagnetic

Interference ESD Susceptibility Per EN61000-4-2, level 4, contact discharge. 8 kV Radiated

Susceptibility EFT/Burst Per EN61000-4-4, level 3. ± 2 kV Input Surge Per EN61000-4-5, level 3. Line to Line

Input to Output per EN60950. 4243 VDC

EN55022 / CISPR 22 Conducted:

Radiated:

Per EN61000-4-3, level 3. 10 V/m

Line to Ground

A A

1 2

Class

Page 10

PD05: CP3-SVE-P200AC CPCI Power Supply

SAFTEY, REGULATORY, AND EMI

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Conducted Disturbance

Insulation Resistance

Per EN61000-4-6, level 2. 3 V

Input to Output. 10 MΩ

ENVIRONMENTAL

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Altitude Operating.

Non-Operating.

Operating Temperature

Storage Temperature

Relative Humidity Non-Condensing. 5 95 %RH Shock Peak acceleration. 20 GPK Vibration Random vibration, 10 Hz to 2 kHz, 3 axis. 6 GRMS

With 250 LFM forced-air cooling At 100% load: Derate linearly above 50°C by 2.5% per °C. At 50%

load:

0 50

- 40 + 85 °C

10k 40k

ASL Ft.

°C

Warning!

Adequate thermal cooling of the power supply must be ensured. Therefore do not obstruct or hinder cooling air circulation or heat conduction within the power supply or surrounding equipment.

Failure to comply with this warning may result in damage to yo ur equipment.