Kontron CP3-SVE-M120DC User Manual

Download

Page 1

CPCI

Power Supply

Manual

PRODUCT DOCUMENTATION

PD02

CP3-SVE-M120DC

Reference ID: 24139 PD02

Revision: 01

Issued: February 01, 2002

The product described in this manual is in compliance with all applied CE standards.

Page 2

PD01: CP3-SVE-ATX235AC CPCI Power Supply

Revision History

CPCI Power Supply Manual:

Manual/Product Title:

Reference ID: 24139 PD02

Product Documentation: CP3-SVE-M120DC

Rev.

Index

01 Initial Issue Feb. 01, 2002

Brief Description of Changes Date of Issue

Imprint

Copyright © 2002 PEP Modular Computers GmbH. All rights reserved. This manual may not be copied, photocopied, reproduced, translated or converted to any electronic or machinereadable form in whole or in part without prior written approval of PEP Modular Computers GmbH.

DISCLAIMER:

PEP Modular Computers GmbH rejects any liability for the correctness and completeness of this manual as well as its suitability for any particular purpose.

This manual was realized by: TPD/Engineering, PEP Modular Computers GmbH.

Page 3

CPCI Power Supply PD01: CP3-SVE-M120DC

1. Introduction

The specific product description provided with this product documentation is part of the PEP’s CPCI Power Supply manual. For further information, in particular regarding general details as well as safety and warranty statements, refer to the CPCI Power Supply Manual, ID 24139.

2. 120W M-Type Power Supply Unit

The main features of the 3U M-type, lower-range input, 120W output DC/DC power supply unit CP3-SVE-M120DC are described in the following table:

Table 1: Distinctive Features of Power Supply Unit CP3-SVE-M120DC

Feature Specification

Form Factor

Front Panel Size

Mechanics

Plug-In Compatibility

Power Supply Connector

Input Voltage

Output Power

Output Voltages/Currents

Cooling

Redundant Supply Capability

Status Indication

60.96* 133.35 mm 19” rack Yes DIN M24/8 connector

8.5V..36V 120W Vo1 = +3.3V at 14A

= +5.1V at 14A

= +12V at 2A

= -12V at 1A

Free convection — Separate LEDs for Vo1..V

Special Feature(s)

E1 heat-resistant variant (option)

Page 4

PD01: CP3-SVE-M120DC CPCI Power Supply

2.1 Mechanical Specifications

Figure 1: View of Power Supply Unit CP3-SVE-M120DC

60.5 mm (12HP)

100 mm (3U)

171.93 mm

Page 5

CPCI Power Supply PD01: CP3-SVE-M120DC

2.2 Power Supply Connector

Figure 2: Orientation of the DIN M24/8 Power Supply Connector

Table 2: DIN M24/8 Connector Pinouts

Pin Function Pin Function

L1 (live connection)

The DC

input voltages to the power

supply unit and the Vo1...Vo4 output voltages from the power supply unit to the backplane are connected via a 32-pole DIN 24/8 male power supply connector.

For the pinouts of the DIN M24/8 power supply connector please refer to the following table.

B.17

+3.3VL

11 A.13 A.14 A.15 A.16 A.17 A.18 A.19 A.20 B.13 B.14 B.15 B.16

N (neutral) PE (earth protection) INT (internally connected) INH INT (internally connected) OVF +5VF +3.3VL +12VL

-12VL +3.3VL +3.3VL +3.3VL +3.3VL

B.18 B.19 B.20 C.13 C.14 C.15 C.16 C.17 C.18 C.19 C.20

22 25

+3.3VL +12VL

-12VL EN DEG INT (internally connected) +3.3VL +3.3VL +3.3VL +12VL

-12VL +5VL OVL

Page 6

PD01: CP3-SVE-M120DC CPCI Power Supply

2.3 Installation

Thanks to its plug-in compatibility this DIN M-type power supply unit allows for an easy installation, by which the power supply unit’s male DIN M24/8 power connector is inserted into the backplane’s mating female connector without the need of any intermediate adaptation.

Warning!

To ensure a safe 5 V operation of your equipment it is necessary th at

on the backplane 5VL is connected to 5VF and 0VL to 0VF. PEP sys-

tems provide this configuration by default.

The maximum voltage compensation is 0.25V per line.

2.4 Electrical Specifications

Input

Input voltage ranges 8.5V..36V DC Efficiency Typ. 80% Input current limitation

Typ. ≤ 35A Typ. ≤ 60A

(cold state)

peak

(hot state)

peak

Fuse 25A

Output

Adjustment range V

, V

Status indication Green LED’s for V

± 5%

, Vo2, Vo3, V

Ripple Vo1, Vo2 < 50mVpp,

, Vo4 < 30mV

Noise voltage Typ. 50mVpp (band width 20MHz) Temperature coefficient 0.025% / K

Switch on / switch off performance No overshooting of V

(soft-start)

Rise-delay time < 0.5s Run-up time ≤ 50ms

Page 7

CPCI Power Supply PD01: CP3-SVE-M120DC

Figure 3: Output Power Diagrams

Regulation

Line regulation < 0.2% for V

< 0.5% for Vo3, V

, V

o2 o4

Load regulation < 0.1% for Vo1*

< 0.1% for V < 5.0% for Vo3, V

* <1% with redundancy

Response time < 0.5ms at Io 20..80%

Protection and Control

Overvoltage protection 125% ± 5% for V

125% ± 10% for Vo3, V Automatic repetition

Current limitation Typ. 110% of I

Typ. 140% of I

Rated Rated

Effective for all outputs, outputs short-circuit proof

, V

for Vo1, V

for Vo3, V

Overtemperature protection Switches off when inside temperature

becomes too high, switches on again with hysteresis

Signal DEG (Derate) Open-collector, I

Low during start-up of V high 100-200ms after start-up of V low ≥ 5ms before break-down of V

max

= 48mA

o o

(mains failure/switch-off with EN/INH)

Input EN (enable) Input INH (inhibit)

Power is ON only with EN low (TTL) Power always OFF with INH low (TTL)

Page 8

PD01: CP3-SVE-M120DC CPCI Power Supply

EMC

Interference suppression/immunity EN 50082-2: 1992

EN 61000-4-2:Intensity 4 EN 61000-4-3:Noise level 10V/m EN 61000-4-4:Intensity 4 EN 61000-4-5:Intensity 3 EN 61000-4-11 VDE (with switch-off and re-start)

Interference emission EN 50081-1:1992

EN 55011/EN 55022: ClassB, interference transmission depends on assembly

Safety

EN 60950/VDE 0805 Safety Class I, VDE 0100

Operating Data

Temperature range 0°C..+70°C with free convection Temperature derating 2% / K at +50°C (see diagram)

Warning!

Adequate thermal cooling of the power supply must be ensured.

Therefore do not obstruct or hinder cooling air circulation or heat con-

duction within the power supply or surrounding equipment.

Failure to comply with this warning may result in damage to yo ur

equipment.