Page 1
UK
KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: KH2400-06/07-V1
Page 2
Steam and dry iron KH 2400
Operating instructions
Page 3
Page 4
Page 5
KH2400
Content Page
Proper use 4
Package Contents 4
Technical Data 4
Safety Instructions 4
Parts Identification 6
Before first use 6
Controlling the temperature 6
Ironing tips 7
How to fill with water 7
Auto shut-off safety feature 7
Steam ironing 8
Using the steam burst button 8
Using the spray-button 9
Anti-scale system 9
Using the calc clean button 9
Drip-stop feature 10
Using as a dry iron 10
Care and cleaning instructions 10
Emptying and storing the iron 10
Disposal 11
Warranty and customer service 11
Importer 11
Read the operating instructions carefully before using the appliance for the first time
and preserve this booklet for later reference. Hand over the manual to anyone you
pass on the appliance to.
- 3 -
Page 6
KH2400
Steam and dry iron KH 2400
Proper use
The steam and dry iron is intended purely for ironing clothes in private households. In addition, creases in hanging
clothes, curtains, etc. can be removed
using the vertical steam burst function.
Do not use the appliance for any other
than its intended use.
Package Contents
Steam iron
Measuring cup
Storage cover
Operating instructions
Warranty card
Technical Data
Nominal voltage: 230 V~ 50Hz
Nominal output: 2200 W
Safety Instructions
Danger of Burns!
• Keep the steam iron out of reach of
children. Never permit children to use
the steam iron.
• Never touch the sole-plate of the iron
when it is hot. Take hold of the steam
iron with the handle only.
• Never hold your hand over the steam
spray or on hot metal parts.
• Never direct the steam blast at people
or other living creatures.
• You should not open the filler opening
of the water reservoir while the iron
is in use. First remove the plug from
the power socket and allow the steam
iron to cool down before refilling it.
Fire hazard!
• Never leave the steam iron unattended
when it is hot or switched on. You
and others can be easily injured
through a still hot iron.
• Never place the steam iron in the close
vicinity of inflammable materials, such
as curtains and drapes. They could
catch fire.
• Use only the ironing temperatures given
in the care instructions for the material
and those suitable for it. Otherwise,
you could damage the textiles. Should
care instructions for the item be neither
known nor available, begin ironing
with the lowest temperature setting.
- 4 -
Page 7
KH2400
• Put the steam iron into storage only
when it has cooled down completely.
• Never place the steam iron on edges,
for example table edges. It could tip
and fall down.
• Stand the steam iron only on its back
end, or lay it in the support tray provided on the ironing board. Never lean
the hot iron against walls or other objects. There could be a risk of fire
breaking out.
Danger of electrical shock!
• Connect the steam iron only to correctly
installed wall power sockets.
• To avoid possible dangers, arrange for a
defective appliance to be checked and
possibly repaired by qualified technicians, or contact our Customer Service
Department.
• Arrange for defective power cables to
be replaced immediately by qualified
technicians, or contact our Customer
Service Department.
• To disconnect from the power source,
pull only on the plug itself, not on the
cable.
• Never direct the steam jets or the waterspray jets at electrical appliances or at
objects sensitive to heat or moisture.
• Never bend (kink) or crush the power
cable. Arrange it in such a way that it
can not come into contact with hot
surfaces and such that no-one can
step on it or trip over it.
• After every use, before cleaning and
when refilling with water , remove
the plug from the power socket.
• Always unroll the power cable fully
before switching on and do not use
an extension cord.
• Never touch the power cable or the
power plug with wet hands.
• Under no circumstances should you
submerge the steam iron in any liquid
or permit liquids to penetrate into the
housing of the steam iron. You should
never expose the appliance to moisture
or use the device outdoors. Should
liquids penetrate into the appliance
housing , immediately remove the plug
from the power source and arrange
for the appliance to be repaired by a
qualified specialist workshop or by the
Customer Service Department.
• Never use the steam iron adjacent to
water contained in a bath, shower,
wash basin or other vessels. The proximity of moisture presents a danger,
even when the appliance is switched
off.
• You may not open the housing of the
steam iron. Arrange for a defective
steam iron to be repaired only by a
qualified specialist workshop or by
the Customer Service Department.
• Should the steam iron fall to the
floor, become otherwise damaged, or
the power plug or cable becomes defective, it may no longer be taken into use. In such cases, arrange for the
appliance to be checked and possibly
repaired by a qualified workshop or
our Customer Service Department.
• Do not allow individuals (including
children) to use the appliance whose
physical, sensorial or mental abilities
or lack of experience and knowledge
hinder their safe usage of it if they
have not previously been supervised
or instructed in its correct usage.
- 5 -
Page 8
KH2400
Tell children about the appliance and
its potential dangers so that they do
not play with it.
Important!
• Should the clothing care instructions
forbid ironing, (Symbol ), the clothing item may not be ironed. If you
ignore this warning, the item could
be damaged.
• Do not fill the water tank with a liquid other than water. You will otherwise damage the steam iron.
• You may not clean the steam iron
with solvents, alcohol or abrasive
cleaning agents. You could otherwise cause damages.
Parts Identification
Cable protector / mains lead
Water tank with integrated blue
switch-off control lamp
Temperature control knob
Calc-Clean button
Sole plate
Storage cover
Measuring cup
Spray nozzle
Water tank lid
Steam regulator
Spray button
Steam burst button
Heater monitor light (green)
• Remove the storage cover, sticker or
any protective items from the soleplate .
• It is important to remove any residues
of the polishing compound, used on
the soleplate , which may have lodged in the steam vents. Using the
measuring cup supplied, pour
water into the iron up to the MAX
line. Clean the steam vents by using
“Calc Clean” system. (See using the
Calc Clean Button ). When finished,
wipe the soleplate with an old
cloth. Cotton swabs may be used to
clean and dry the steam vents.
• Some parts of the iron have been
slightly greased and as a result the
iron may smoke slightly when switched on for the first time. After a
short while, however, this will cease.
Open a window.
• Normal tap water can usually be used
for ironing. But if you live in a hard
water area we recommend to use
distilled water to insure
optimum performance of your iron.
Controlling the temperature
Turn your temperature control knob
to the position you desire according to
the following fabric indications:
Before first use
• Before using the iron for the first
time, check if the voltage rating on
the base plate corresponds to the
mains voltage in your home.
- 6 -
Nylon
Nylon
Nylon
Silk
Soie
Seide
Wool
Laine
Wolle
Cotton
Coton
Baumwolle
Linen
Toile
Leinen
Calc Clean
Page 9
KH2400
Ironing tips
Sort the articles to be ironed according
to the fabric. Ironing instructions are
usually stitched onto an inside seam of a
garment and these should be followed
at all times. Start your ironing with the
fabrics requiring the lowest heat setting.
If you are unsure of the fibre content of
a garment, test a small area (a seam or
inside hem) before ironing. When in
doubt, start with low heat. If wrinkles
remain, gradually increase the heat to
find the best setting for good results
without damaging the fabric.
How to fill with water
Check that the steam control gear is
in the dry position (position 0) when filling the water tank .
Pull back the water tank lid and fill
the tank to the “MAX” line. Do not
overfill. Check the water level in the
tank in the position shown.
Water hardness Ratios - distilled
water to mains
water
very soft / soft 0
medium 1 : 1
hard 2 : 1
very hard 3 : 1
The water hardness level can be queried
at your local water works.
Auto shut-off safety feature
The automatic shut-off function ensures
that the iron is automatically shut off
after a standstill of 30 seconds in horizontal position or 8 minutes in vertical
position.
When the iron is automatically shut off,
the blue shut-off indicator light in water
tank starts to flash.
If you move the iron gently back and
forth, it switches on again. The green
heater monitor light comes on again
when the temperature at the sole plate
drops below the set ironing temperature. Wait until the green heater monitor light goes out.
The iron has then reached the set ironing temperature and can now be used.
Use only clean mains water, without any
form of additive. Other fluids damage
the appliance. To extend the optimal
steam blast function, mix mains water
with distilled water according to the
table.
- 7 -
Page 10
KH2400
Steam ironing
Unwind the mains lead. Ensure that the
iron is disconnected from the power supply before you fill it with water. Turn
steam regulator to the dry position (0
position) and the temperature control
knob to MIN.
Fill the iron with water. Ensure that the
MAX marking line is not exceeded. Connect the appliance to the mains power
supply again. The blue shut-off indicator
light in water tank comes on.
Set the temperature control knob to
the steam position and the heating
light will illuminate. In this setting,
the iron can be used as a steam iron
once the heating light goes out. The
heating light will illuminate and go
out regularly during ironing as an indication that the temperature control is
working properly.
Setting the knob
You can adjust the steam easily with the
7 positions of the steam control gear.
Put the iron on the heel rest when rearranging clothing or while not in use.
Steaming stops when the iron is placed
on the heel rest.
Using the steam burst button
Be sure there is water in the tank and
the temperature control knob is on
steam.
Using the iron horizontally
Lift the iron and press the steam burst
button . You may need to press this
button a few times after filling the
iron with water to activate the pump.
The burst steam facility can be used only
when ironing at temperature of at least
150° C, this means form III to MAX.
Turn the steam control gear to the
steam position and the iron will create
steam. Turn the steam control gear to
the position 0, and the steam will cease.
Steam adjustable
Using the iron vertically
- 8 -
Page 11
KH2400
The burst function can be also used
when the iron is held in vertical position
to remove creases from hanging clothes,
curtains, etc.
Using the spray-button
Provided there is sufficient water in the
tank , you can use the spray button
at any temperature setting and when
steam or dry ironing. While ironing,
press the button several times to activate the pump.
Anti-scale system
The integrated anti-scale system reduces
the build up of lime scale and increases
the user life of your iron
Using the calc clean button
It is important to use the Calc-Clean
function before putting the iron into
operation for the first time and then at
regular intervals in order to remove lime
particles and other impurities. We
recommend that the Calc-Clean function
is used at least twice a month. In areas
with very hard water, the iron should be
cleaned with the Calc-Clean function
after every use, or use distilled water.
• Fill the water up to “MAX” line in
water tank .
• Insert the plug into the wall socket.
• Set the temperature control to
MAX.
• Allow the iron to heat up until the
heating light goes out and then
lights again.
• Remove the plug from the wall socket.
• Hold the iron horizontally over the sink.
• Set the steam control gear to calc
clean position (0) then press and hold
the calc clean button . The boiling
water and steam will drain from the
vents in the soleplate . Impurities
and scale will be drained away with
the water.
• Move the iron backwards and forwards while draining the water.
• Release the calc clean button once
all water has been drained out.
• Place the iron in the upright position,
plug it and then allow it to heat up.
• Carefully dry soleplate by ironing
over a towel or old cloth to ensure
there is no remainder of the water
inside the steam chamber.
• Let the iron cool down completely
before storing it.
- 9 -
Page 12
KH2400
Drip-stop feature
As indicated on the temperature control
knob , steam ironing is only possible at higher ironing temperatures. With
conventional steam irons, water may
drip from the soleplate if an extremely
low temperature has been selected.
However, a new feature has been added
to this iron – ‘DRIP STOP’ steam shut-off.
This means that the iron will automatically stop steaming at low temperatures.
When this happens, you will hear a
“CLICK”. Then set the temperature control to the required temperature.
Steaming will recommence as soon as
the required temperature has been reached.
Using as a dry iron
The iron can be used as a dry iron, even
if there is water in the water tank . Do
not put water in the water tank when
the iron is to be used as a dry iron for
many hours.
• Put the iron on the heel rest and then
plug the iron into the mains.
• Turn the steam control gear to
“O”.
• Set the temperature control knob
to the required temperature.
• When the heating light goes out, it
indicates that the iron has reached
the required temperature.
Care and cleaning instructions
• Ensure that the soleplate remains
smooth and unscratched by ironing
around on not over zippers, rivets or
any other objects which may scratch
the soleplate.
• The hardness of the water and its
minerals differs widely from region to
region. If the water in your area is
very hard, we recommend the use of
distilled water that is available in
retail stores in order to ensure the
optimum function of the iron. If you
do not use distilled water, clean the
iron regularly using the Calc-Clean
function (see section “Calc-Clean
Function”).
• Do not disassemble or repair your iron
yourself.
• After each use, remove the plug and
let the iron cool down. Wipe the soleplate with a damp cloth and nonabrasive (liquid) cleaner. Clean the
iron body with a damp cloth.
Emptying and storing the iron
• Slide the steam control gear several
times from 0 to the steam position
and back again (self-cleaning).
• Be sure the iron is unplugged first.
• Pour out any remaining water by shaking the iron.
• Make it a habit to empty the iron
after each use.
• Put the iron on the storage cover. Do
not use the storage cover while ironing.
• Wind the power cord around the cord
winder. Do not wrap the power cable
too tightly!
- 10 -
Page 13
KH2400
• On a stable surface, store the iron with
storage cover in the horizontal
position.
• Let the iron cool down completely
before storing.
Disposal
Do not dispose of the device in
normal domestic waste.
Dispose of the device over a registered
waste disposal firm or through your
communal waste disposal facility.
Observe the currently valid regulations.
In case of doubt, consult your waste
disposal facility.
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
www.kompernass.com
Dispose of the packaging materials in an environmentally responsible manner.
Warranty and customer service
The warranty conditions and service centre address can be found in the enclosed
warranty slip.
- 11 -
Loading...