Homeowners Guide
Cleansing Seat
Français, page “Français-1”
Español, página “Español-1”
1341257-5-A
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE
USING
When using electrical products, especially when children are present,
basic safety precautions should always be followed, including the
following:
WARNING: Risk of personal injury. Do not remove the UV
lamp protective cover. Eye damage may result from viewing
the UV light directly. Always be certain the lamp is off before
opening the protective cover.
CAUTION: Risk of personal injury. Replacement of the UV
lamp must only be performed by qualified service personnel.
IMPORTANT! Risk of product damage. Do not install this product
in a location exposed to excessive moisture where condensation
might form on the product surface. Provide adequate ventilation
when bathing to avoid damage to the electronic components due to
high humidity levels.
IMPORTANT! Risk of product or property damage. Pushing or
pulling on the water connection may cause water leakage.
IMPORTANT! Risk of product damage. Do not apply excessive
force to the spray wands.
IMPORTANT! Risk of product damage. In areas where water may
freeze in the pipes, make arrangements to keep the pipes warm.
Any water remaining in the seat may freeze during winter storage.
Allow the unit to warm to room temperature before reinstalling or
using.
IMPORTANT! Risk of product damage. Do not supply electrical
power to the unit until the plumbing installation work has been
completed, as it may cause the product to malfunction.
NOTE: The thermal protectors may trip during storage or
transportation in warm weather causing the unit to not operate.
Allow the unit to cool to room temperature before installation or
operation.
1341257-5-A 2 Kohler Co.
IMPORTANT SAFEGUARDS (cont.)
DANGER: To reduce the risk of electrocution:
Do not place or store this product where it can fall or be pulled
into a bath or sink.
Do not place in or drop into water or other liquid.
Do not reach for a product that has fallen into water. Unplug
immediately.
WARNING: To reduce the risk of burns, electrocution, fire,
or injury to persons:
Close supervision is necessary when this product is used by or
near children, the elderly, or invalids. Adjust the temperature of
the seat for the elderly, those who are incapacitated, or persons
with sensitive skin.
Use this product only for its intended use as described in this
manual. Only use attachments recommended by Kohler Co.
Never operate this product if it has a damaged cord or plug, if it
is not working properly, if it has been dropped, damaged, or
dropped into water. Return the product for examination and
repair.
Keep the cord away from heated surfaces.
Never block the air openings of the product or place it on a soft
surface, such as a bed or couch, where the air openings may be
blocked. Keep the air openings free of lint, hair, and the like.
Never use while sleeping or drowsy.
Never drop or insert any object into any opening or hose.
Do not use outdoors or where aerosol spray products are being
used or where oxygen is administered.
Connect this product to a properly grounded outlet only. See the
“Grounding Instructions” section.
This product conforms to applicable provisions of US 21 CFR,
Chapter 1, Subchapter J, Radiological Health.
SAVE THESE INSTRUCTIONS
Kohler Co. 3 1341257-5-A
Grounded
Outlet
Grounding
Plug
Grounding Instructions
WARNING: Risk of electric shock, fire, or personal injury.
This product must be grounded and connected only to a
dedicated, nominal 120 VAC, 60 Hz circuit protected by a
minimum 15 A Ground-Fault Circuit-Interrupter (GFCI) or
Residual Current Device (RCD).
This product should be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product is
equipped with a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is properly
installed and grounded.
DANGER: Risk of electric shock. Improper use of the
grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not
connect the grounding wire to either flat blade terminal. The wire
with insulation having an outer surface that is green with or
without yellow stripes is the grounding wire.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt whether the product is properly grounded.
Do not use an extension cord with this product.
1341257-5-A 4 Kohler Co.
A
BC D
MLK
Remote Control
N
HG F E
J
P
Panel
Q
Remote Control Operation
NOTE: For features with multiple settings, press the icon to move
the setting one level higher. If the feature is set at the highest level,
pressing the icon will deactivate it or adjust it to a lower setting.
NOTE: Make sure that four AA batteries are installed correctly in
the remote control.
A - Preset 1 and Preset 2: The presets allow two users to save
their feature settings. When ″Preset 1″ or ″Preset 2″ are selected,
the saved preferences will activate. Refer to the ″User Presets″
sections below.
B - Deodorizer: Press the ″Deodorizer″ icon to activate the
deodorizer. Press the ″Stop″ icon to deactivate. To disable this
feature, press and hold the ″Deodorizer″ icon for 3 seconds.
C - Clean: To activate the 45-minute UV disinfecting cycle, press
the ″Clean″ icon. Lifting the seat lid ends the process. Automatic
UV disinfection reactivates every 24 hours. To disable this feature,
press and hold the ″Clean″ icon for 3 seconds.
Kohler Co. 5 1341257-5-A
Remote Control Operation (cont.)
D - Battery Indicator: Shows the status of the battery charge.
When the battery is at 100%-50% charge, the icon is off. When the
battery is at 49%-20% charge, the icon flashes for 4 seconds after
the last icon is pushed. When the battery is at 19% or less charge,
the icon glows for 4 seconds after the last icon is pushed.
E - Dryer: Press the ″Dryer″ icon once to activate the dryer. Press
again to increase the air temperature. There are six settings.
F - Seat Temp: Press the ″Seat Temp″ icon to activate the heated
seat. Press again to increase the temperature. There are five
settings.
G - Water Temp: Press the ″Water Temp″ icon to adjust the water
spray temperature. There are five settings.
H - Position: Press the ″Position″ icon to adjust the wand
position when front or rear wash is active. There are five settings.
J - Pulsate + Oscillate: When front or rear wash is active, press
the ″Pulsate + Oscillate″ icon once to oscillate the wand back and
forth. Press again to pulsate the water flow. Press a third time to
oscillate and pulsate simultaneously. Press again to turn off the
feature.
K - Rear: Press the ″Rear″ icon to activate the rear wash feature
and adjust the rear wash water pressure.
L - Front: Press the ″Front″ icon to activate the front wash feature
and adjust the front wash water pressure.
M - Stop: Press the ″Stop″ icon to stop the front wash, rear wash,
and dryer features.
N - Rear: Press the ″Rear″ icon to activate the rear wash feature
and adjust the rear wash water pressure.
P - Front: Press the ″Front″ icon to activate the front wash feature
and adjust the front wash water pressure.
Q - Stop: Press the ″Stop″ icon to stop the front wash, rear wash,
and dryer features.
Setting the User Presets
NOTE: The presets allow two users to save their feature settings.
When ″Preset 1″ or ″Preset 2″ are selected, the saved preferences
will activate.
While seated, adjust the seat features to your preferences.
1341257-5-A 6 Kohler Co.
Remote Control Operation (cont.)
Press and hold the ″Preset 1″ or ″Preset 2″ icon for 3 seconds to
save activated features at the current settings.
To change a setting, adjust the front wash, rear wash, or dryer
feature while the preset is in use. Press and hold the ″Preset 1″ or
″Preset 2″ icon for 3 seconds to store the new setting to memory.
Using the User Presets
Press the ″Preset 1″ or ″Preset 2″ icon while you are seated to
activate front wash, rear wash, dryer temperature and speed, and
seat temperature at your stored settings.
If the ″Preset 1″ or ″Preset 2″ icon is pressed while the seat is not
occupied, the seat will gradually (approximately 2 minutes)
change to the preset temperature.
To reset or delete a preset, press and hold the ″Preset 1″ or
″Preset 2″ and the ″Stop″ icons at the same time for three
seconds.
Nightlight
To turn off the nightlight, press and hold the ″Stop″ icon for three
seconds.
To disable the nightlight, press and hold the ″Front″ icon for three
seconds.
Pairing a Remote Control
A new remote control must be paired with the seat before use.
Only one remote control can be paired with the seat at a time.
Bring the new remote control near the seat.
Make sure that all other remote controls have been removed from
the area of the seat.
Press and hold the ″Dryer″ icon until the icon flashes.
Simultaneously press and hold the ″Front″ and ″Rear″ icons on
the seat until a beep is heard.
When the ″Dryer″ icon on the remote control stops flashing and
the ″Preset 1″ and ″Preset 2″ icons are no longer illuminated, the
remote control has been successfully paired with the seat.
Kohler Co. 7 1341257-5-A
Care and Cleaning
For best results, keep the following in mind when caring for your
KOHLER product:
IMPORTANT! Do not immerse product in water.
•
Always test your cleaning solution on an inconspicuous area
before applying to the entire surface.
•
Use a soft, dampened sponge or cloth to wipe surfaces clean.
Remove the cleaner quickly after applying. Rinse and dry any
overspray that lands on nearby surfaces.
•
Do not allow cleaners to soak on surfaces.
•
Never use an abrasive material such as a brush or scouring pad
to clean surfaces.
For detailed cleaning information and products to consider, visit
kohler.com/clean. To order Care & Cleaning information, call
1-800-456-4537.
1341257-5-A 8 Kohler Co.
Spray
Wand
Cleaning the Wand
NOTE: The spray wand can only be extended for cleaning when
the seat is not activated or occupied.
Raise the lid and seat.
Press the ″Position″ icon on the panel to extend the wand
forward for cleaning.
Clean the spray wand with a soft-bristled brush and hot water.
Press the ″Position″ icon again to retract the wand.
Kohler Co. 9 1341257-5-A
Inlet
Filter Screen
Cleaning the Screen
NOTE: Clean the filter screen every 6 months or when there is a
reduction in the maximum water flow from the spray wand.
Turn off the water at the supply stop.
Press the release button to disengage the seat from the mounting
bracket. Refer to the ″Removing the Seat″ Section.
Slide the seat forward to allow access to the hose inlet.
Disconnect the water supply hose from the seat connection.
Using long-nosed pliers, carefully remove the filter screen from
the inlet.
Clean the filter screen with a soft-bristled brush.
Reinstall the filter screen.
CAUTION: Risk of product damage. Do not cross-thread the hose
connection to the inlet.
Reconnect the water supply hose to the inlet, one-quarter turn
past hand tight.
Reinstall the seat.
Turn on the water supply.
Check all connections for leaks, and make any adjustments as
needed.
1341257-5-A 10 Kohler Co.
Deodorizer
Block
Cover
Housing
Replacing the Deodorizer
NOTE: The deodorizer should be replaced every two years or when
the deodorizing performance decreases.
Remove the cover.
Carefully remove the deodorizer housing from the seat.
Remove the deodorizer block from the housing.
Insert the new deodorizer block in the housing.
Reinstall the housing into the seat.
Reinstall the cover.
Kohler Co. 11 1341257-5-A
Mounting
Plate
Release
Button
Removing the Seat
For Cleaning
IMPORTANT! When removing the seat for cleaning, take care to
avoid exerting any force on the hose connections.
Press the release button.
Slide the seat forward to access the area around the mounting
plate. Avoid putting pressure on the hoses.
Clean the area as needed.
To reinstall, slide the seat back until it engages the mounting
plate.
For Servicing
Turn off the water at the supply stop.
Flush the toilet to relieve any pressure from the supply hose.
Unplug the power cord from the electrical outlet.
Disconnect the water supply hose from the T-valve.
Press the release button.
Slide the seat forward to disengage from the mounting plate.
When servicing is complete, reinstall the seat and reconnect all
components.
1341257-5-A 12 Kohler Co.
Servicing the Batteries
Remove the remote control from the remote dock.
Open the door to the battery compartment.
Remove the batteries.
Install the replacement batteries, oriented as shown.
Close the door to the battery compartment.
Reinstall the remote control to the remote dock.
Troubleshooting
This troubleshooting guide is for general aid only. A Kohler Co.
Authorized Service Representative (ASR) or qualified electrician should
correct any electrical problems.
For warranty service, contact the Customer Care Center using the
numbers located on the back page of this manual.
Cleansing Features
Symptoms Probable Causes Recommended Action
1. The seat
features are not
working.
A. A power failure
has occurred.
B. The power cord is
unplugged.
A. Wait until power is
restored.
B. Plug the power cord
into a GFCI or RCD
electrical outlet.
Kohler Co. 13 1341257-5-A
Troubleshooting (cont.)
Cleansing Features
Symptoms Probable Causes Recommended Action
2. The seat is
loose.
3. Water stops
flowing from
the spray
wand before
cleansing is
complete.
C. The Ground-Fault
Circuit-Interrupter
(GFCI) or Residual
Current Device
(RCD) is tripped.
D. The user is not
detected by the
seat sensor.
A. The mounting
plate fasteners are
loose.
A. Washing
automatically stops
1 minute after
pressing a spray
icon.
B. The user shifted
position and is no
longer detected by
the seat sensor.
C. Reset the GFCI or
RCD.
D1. Small children may
be too light to be
detected by the
sensor.
D2. Shift your position
on the seat. The
sensor is located on
the front of the seat.
A. Tighten the fasteners.
Refer to the
Installation Guide.
A. Press the ″Front″ or
″Rear″ icon to restart
cleansing.
B. Shift your position
on the seat. The
sensor is located on
the front of the seat.
Remote Control Compliance
FCC ID: N82-KOHLER024, N82-KOHLER025
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
1341257-5-A 14 Kohler Co.
Remote Control Compliance (cont.)
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
CANADA IC: 4554A-KOHLER024, 4554A-KOHLER025
This device complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (EIRP) is
not more than that necessary for successful communication.
Warranty
KOHLER Intelligent Toilet and C3 Cleansing Seat Three-Year Limited
Warranty
Kohler Co. warrants that its toilets with integrated cleansing
functionality (″Intelligent Toilets″) and electric cleansing seats will be
free of defects in material and workmanship during normal residential
Kohler Co. 15 1341257-5-A
Warranty (cont.)
use for three years from the date the product is installed. This
warranty applies only to intelligent toilets and electric cleansing seats
installed in the United States of America, Canada and Mexico (″North
America″).
If a defect is found in normal residential use, Kohler Co. will, at its
election, repair, provide a replacement part or product, or make
appropriate adjustment where Kohler Co.’s inspection discloses any
such defect. Damage caused by accident, misuse, or abuse is not
covered by this warranty. Improper care and cleaning will void the
warranty*. Proof of purchase (original sales receipt) must be provided
to Kohler Co. with all warranty claims. Kohler Co. is not responsible
for labor charges, installation, or other incidental or consequential costs
other than those noted above. In no event shall the liability of Kohler
Co. exceed the purchase price of the intelligent toilet or electric
cleansing seat.
If the intelligent toilets or electric cleansing seats are used
commercially or are installed outside of North America, Kohler Co.
warrants that the intelligent toilet or electric cleansing seat will be free
from defects in material and workmanship for one (1) year from the
date the product is installed, with all other terms of this warranty
applying except duration.
If you believe that you have a warranty claim, contact your Home
Center, Dealer, Plumbing Contractor or E-tailer. Please be sure to
provide all pertinent information regarding your claim, including a
complete description of the problem, the product, model number, the
date the product was purchased, from whom the product was
purchased and the installation date. Also include your original invoice.
For other information, or to obtain the name and address of the service
and repair facility nearest you, write Kohler Co., Attn: Customer Care
Center, Kohler, Wisconsin 53044 USA, or by calling 1-800-4-KOHLER
(1-800-456-4537) from within the USA and Canada, and
001-800-456-4537 from within Mexico, or visit www.kohler.com within
the USA, www.ca.kohler.com from within Canada, or
www.mx.kohler.com in Mexico.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. KOHLER CO. AND/OR SELLER DISCLAIM ANY
LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states/provinces do not allow limitations of how long an
1341257-5-A 16 Kohler Co.
Warranty (cont.)
implied warranty lasts or the exclusion or limitation of such
damages, so these limitations and exclusions may not apply to you.
This warranty gives the consumer specific legal rights. You may also
have other rights that vary from state/province to state/province. This
warranty is to the original consumer purchaser only, and excludes
product damage due to installation error, product abuse, or product
misuse, whether performed by a contractor, service company, or the
consumer.
This is Kohler Co.’s exclusive written warranty.
* Never use cleaners containing abrasive cleansers, ammonia, bleach,
acids, waxes, alcohol, solvents or other products not recommended for
stainless steel or polypropylene plastic. This will void the warranty.
Kohler Co. 17 1341257-5-A
Loading...