Kohler K8760 User Manual

BELLWETHERTM

Features

Cast iron with Safeguard

•

ADA compliant when installed per Section 607 of the

•

Act 60″ (152.4 cm) x 32″ (81.3 cm) x 15-1/2″ (39.4 cm)

•

ﬁnish

Codes/Standards Applicable

Speciﬁed model meets or exceeds the following:

ADA

•

ASME A112.19.1/CSA B45.2

•

ICC/ANSI A117.1

•

Speciﬁed Model

BATH WITH APRON

K-875

ALSO K-876

Colors/Finishes

0: White

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

Accessories

CP: Polished Chrome

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

NA: None applicable

•

Model Description Colors/Finishes

K-875 Bath with apron – left drain ❑ 0 ❑ Other_____ K-876 Bath with apron – right drain (shown) ❑ 0 ❑ Other_____

Required Accessories

K-7214 Clearﬂo cable bath drain, less PVC tubing ❑ CP ❑ Other_____ K-7261 Fitting/pipe kit ❑ NA

Optional Accessories

K-952 Stillness K-10044 Oblo K-14426 Purist

wall-mount bath spout ❑ CP ❑ Other_____

wall-mount non-diverter bath spout, 35° ❑ CP ❑ Other_____

Product Speciﬁcation

The bath with apron shall be made of cast iron with Safeguard ﬁnish. Bath shall be 60″ (152.4 cm) in length, 32″ (81.3 cm) in width, and 15-1/2″ (39.4 cm) in height. Bath shall be ADA compliant when installed per Section 607 of the Act. Bath shall be Kohler Model K-____-____ .

Page 1 of 2 1074694-4-

USA/Canada: 1-800-4KOHLER

(1-800-456-4537)

www.kohler.com

BELLWETHERTM

Optional Accessories continued

K-14427 Purist K-15137 Coralais K-15138 Coralais K-16246 Margaux

wall-mount non-diverter bath spout, 90° ❑ CP ❑ Other_____

non-diverter bath spout ❑ CP ❑ Other_____

diverter bath spout ❑ CP ❑ Other_____

wall-mount bath spout ❑ CP ❑ Other_____

Technical Information

Fixture*: Bathing well: Basin area, bottom 41-1/4″ (104.8 cm) x

18-3/16″ (46.2 cm)

Basin area, top 51-1/4″ (130.2 cm) x

23-5/16″ (59.2 cm)

Weight 298 lbs (135.2 kg) To overﬂow: Water depth 11-5/16″ (28.7 cm) Capacity 44 gal (166.6 L) * Approximate measurements for comparison only.

No change in measurements if connected with drain and fitting/pipe kit illustrated. (K-7214 and K-7261)

11-7/8" (30.2 cm)

Installation Notes

Install this product according to the installation guide.

Floor support under bath must provide for a minimum of 52 lbs/square foot (252.8 kg/square meter) loading.

4-1/4" (10.8 cm)

15-15/16" (40.5 cm)

Spout Detail

7" (17.8 cm)

"X"

32" (81.3 cm)

60" (152.4 cm)

3-15/16" (10 cm)

BELLWETHERTM BATH WITH APRON Page2of2

1074694-4-

Note: To clear the bath rim end wall, a minimum

7" (17.8 cm) bath spout is recommended. Water flow from angled bath spouts less than 7" (17.8 cm) may also provide needed clearance.

2-3/4" (7 cm)

14-7/8" (37.8 cm)

1/4" (6 mm)

2" (5.1 cm)

Product Diagram

Finished Wall

"X" Depending on length and angle

Rim Flange Detail

1/2" (1.3 cm)

5/8" (1.6 cm)

1/4" (6 mm)

1-1/2" PVC Tee