Kohler K-8752T-W, K-8752T-SW Installation Instructions Manual

Page 1
-1-
ODEON®
INSTALLATION INSTRUCTIONS
VITREOUS CHINA WALL-HUNG P-TRAP TOILET
K-8752T-W/K-8752T-SW
BEFORE YOU BEGIN
·
·
·
consumer.
ORDERING INFORMATION
ODEON Wall-hung Toilet ....................................K-8752T-W
Includes Bowl...................................................K-8750T-W
Includes Toilet Seat..............................................K-8020T
ODEON Wall-hung Toilet..................................K-8752T-SW
Includes Bowl...................................................K-8750T-W
Includes ODEON Quiet-Close Toilet Seat ..........K-8827T
®
®
®
NOTES
·
·
·
·
·
·
Observe all local plumbing and building codes. Shut off the water supply. Passageways is 60mm. Ensure that the new drain and shut-off valve have the correct roughing-in dimensions. . Be very careful while working with vitreous china products. Vitreous china can break or chip if the bolts or nuts are overtightened, or if carelessly handled. Carefully inspect the new bowl for any sign of damage.
See Fig.#1
··Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2013). The product complies with GB 6952-2015.
·
·
·
-
...............................................K-8752T-W
.............................................................K-8750T-W
( )...................................K-8020T
............................................K-8752T-SW
.............................................................K-8750T-W
..............................K-8827T
·
·
·
·
·
·
·
60mm
1
ASME (A112.19.2-
2013) GB 6952-2015·
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 256410
8 256410
©©Copyright Kohler China Investment Co., Ltd. 2016
2016
1207926-T01-B
Page 2
TOOLS AND MATERIALS REQUIRED (Not supplied)
· 254mm adjustable wrench
Metal file (file cut) Tape measure Tubing cutter Level Hacksaw Putty knife Screwdriver Straight pipe coupling Connection packing
·
·
·
·
·
·
·
·
·
()
·
·
·
·
·
·
·
·
·
·
254mm
ROUGHING-IN
Unit: mm
:
Fig.#1
1
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
360
135
225
55
20
102
55
380
400
155
360
430
540
-2-
1207926-T01-B
Page 3
-3-
INSTALLATION
1. INSTALL THE TANK Turn the water supply off before installing the new toilet. Install the concealed tank system in wall before decorating the wall. Install the tank system per tank's installation instructions.
·
·
·
Recommended tanks (Fig.#2-a) and faceplates Kohler in-wall tank and faceplate
Recommended rank dimension(Fig.#2-b)
1) Rank height should be adjust between 0~200mm.
2) Rank should support weight 400kg.
1) K-6281T-W-NA (3/4.5L)
2) K-4179T-NA (3/4.5L)
Faceplates to be matched are K-4177T-CP or K-8857T-CP.
Fig.#2-a
2-a
1.
( 2-b)
1) 0~200mm
2) 400kg
·
·
·
( 2-a)
1) K-6281T-W-NA (3/4.5L)
2) K-4179T-NA (3/4.5L)
K-4177T-CP K-8857T-CP
Fig.#2-b
2-b
400kg
400 10
325
135
35
180
2. SET THE SPACING OF THE BOWL
After you install the tank, be careful to set the spacing of the bowl on wall according to the dimensions as shown.
2.
Fig.#3
3
180 2
135 2
225
325
1
Carrier Studs
25 2
Unit: mm
:
1207926-T01-B
Page 4
-4-
3. ATTACH CONNECTION PIPE Attach pipe with gasket to the inlet to link to the concealed tank. Attach pipe with gasket to the outlet. *Apply gasket for sealing the bowl to wall. You may apply some lubricant to help connect smoothly.
3.
*
·
·
·
·
·
·
Fig.#4
4
Inlet
Outlet
4. INSTALL THE NEW BOWL
Apply a little silicone sealant along the edge, to fill the gap between bowl and wall.
4.
5a
See Fig. 5a.
Fig. #5a
5a
1
Fig. #5b
5b
Place the new bowl on the wall through the carrier. Wrench the nut to tighten and make them attached securely.
Torque for tightening nuts is recommended to be within the range from 8 Nm to 12 Nm.
5b
8Nm 12Nm
See Fig. 5b.
·
·
1207926-T01-B
Page 5
-5-
Fig. #5c
5c
Fig. #5d
5d
Adjust to horizontal and finish tightening.5cSee Fig. 5c.
Apply sealant to make sure the bowl's edge seals to the wall.
5d
See Fig. 5d.
Install the toilet seat according to the toilet seat installation instructions.
0C
o
CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in the toilet rim are kept clean to ensure proper bowl flushing. Toilet bowl cleaners should be used at least once a week. Use a long-handled brush to clean the rim holes, and to clean as far into the trap as possible to prevent mineral deposits from forming.
Most toilet bowl cleaners are not harmful to the vitreous china surface of the toilet bowl. Please follow the bowl cleaner manufacturers instructions carefully.
Do not use abrasive cleaners or solvents.
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage.
Kohler Company shall not be responsible or liable for any damage to these tank fittings caused by the use of cleaners containing chlorine (calcium hypochlorite).
WARNING: Risk of property or product damage.
'
Please do not use hard materials (like scouring pad) to clean product surface, especially the product logo.
CAUTION:
CAUTION: Don t use any cement while installing the toilet.
WARNING: Risk of product damage.
Heat expansion of the toilet may damage the feet of the toilet. Kohler will not be responsible for any damage because of using cement.
Do not throw into the toilet what is easy to block it, such as newspaper, paper pilch, sanitary towel. Do not bump the vitreous china with great force to prevent it from damaging and leaking. Do not use the product in the water below 0 C.
o
1207926-T01-B
Loading...