Kohler K-8741T, K-8767T, K-11184T, K-8753T, K-8709T User Manual

...

Download

BEFORE YOU BEGIN

ODEON

INSTALLATION INSTRUCTIONS

P/S-

VITREOUS CHINA P/S-TRAP TOILET

P-TRAP 180mm K-8711T S-TRAP 255mm K-8753T

S-TRAP 305mm K-8766T

Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation . This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.

All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time withoutnotice.

These instructions contain important care, cleaning, and warranty information-please leave instructions for the

consumer.

ORDERING INFORMATION

Odeon P-trap 180mm Toilet K-8711T

Includes seat K-8741T-* Includes Bowl K-8709T Includes Tank K-8710T

Odeon S-trap 255mm Toilet K-8753T

Includes seat K-8741T-* Includes Bowl K-11184T Includes Tank K-8710T

Odeon S-trap 305mm Toilet K-8766T

Includes seat K-8741T-* Includes Bowl K-8767T Includes Tank K-8710T

Service parts

Fill valve K-82984-B Mounting Plate Assy K-1004142 Flush Valve Assy K-1004139

180mm K-8711T

K-8741T-*

K-8709T K-8710T

255mm K-8753T

K-8741T-*

K-11184T

K-8710T

305mm K-8766T

K-8741T-*

K-8767T K-8710T

K-82984-B K-1004142 K-1004139

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 155mm (6-1/8") centers.

Passageways is 60mm (2-3/8").

Water depth from rim is 245mm (9-5/8")

Ensure that the new drain and shut-off valve have the

correct roughing-in dimensions. . Be very careful while working with vitreous china products.

Vitreous china can break or chip if the bolts or nuts are overtightened, or if carelessly handled. Carefully inspect the new fixture for any sign of damage.

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112. 19.2M).

See Fig.#1

1037406-T01-A

ASME(A112. 19.2M)

-1-

60mm(2-3/8")

528137

155mm(6-1/8")

245mm(9-5/8")

, 2004

TOOLS AND MATERIALS REQUIRED (Not supplied)

254mm adjustable wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Straight pipe coupling

Connection packing

Toilet supply shut-off valve, 10mm (3/8") recommended

()

254mm

10mm(3/8")

WARNING: Risk of external leakage.

The fill valve nut has been factory-tightened, wrench tighten 1/4 turn past finger tight.

NOTICE:

If no shut-off valve exists, install a shut-off valve

below the tank before installing the new toilet.

Flexible hose are recommended to connect the supply line to the fill valve. If you use a rigid connection, take care not to apply side forces to the bottom of the fill valve.

ROUGHING-IN

204

255

777 10

178

102

159

204

396

785 10

388

484

100

1/4

204

776 10

394

305

474

Unit:mm

392

102

698

429

337

390

158

P-trap

8711T

166

267

362

390

INSTALLATION

1. REMOVE EXISTING TOILET Turn off water supply. flush the toilet and use a sponge to remove the remaining water from the tank and bowl. Disconnect the supply shut-off valve (if present) and remove the old tank and bowl.

1037406-T01-A

S-trap

156

-2-

699

428

337

158

8753T

265

362

390

S-trap

()

155

736

433 344

162

8766T

259

363

Fig.#1

2. ASSEMBLE TANK BOLTS&WASHERS Slip bolt heads into mounting plate on bottom of tank. Place large foam washer on base of flush valve.

See Fig. #2a.

Place tank on bowl and attach with nuts and washers from under bowl.

See Fig.#2b.

NOTE:

Do not use white cement or high lime content cements to install this toilet. The expansion of cement due to a rise in temperature may make the toilet crack or cause damage. Kohler is not responsible for any damage caused by installation with the use of cement.

Fig.#2a

3. SELECT P-TRAP OR S-TRAP

to installation your toilet according to the drain and shut-off valve's Roughing-in dimensions.

Fig.#2b

S-trap installation

Fig.#3a

120

255/305

P-trap installation

255/305

180

120

0 8 1

Fig.#3b

1037406-T01-A

-3-

4. INSTALL THE TOILET & CONNECT WATER SUPPLY

Place the toilet in its final location. Use plastic drill guide and 8mm drill bit to drill floor mounting holes for installation over concrete. Use 4mm to 4.5mm drill for wood floor installation.

See Fig.#4a

Install anchors and caps.

WARNING:

to the vitreous can occur.

Do not overtighten floor bolts, as damage

Fig. #4a

8mm

4-4.5mm

NOTE: Do not use white cement or high lime content cements to install this toilet. The expansion of cement due to a rise in temperature may make the toilet crack or cause damage. Kohler is not responsible for any damage caused by installation with the use of cement.

4 Connect fill valve to water supply with hose only. 4

NOTE: use hose only, length:

200-300mm mini. (Not provided.)

200-300mm

()

1037406-T01-A

-4-

5.CHECK WATER LEVEL

Turn on water supply check for leaks. If necessary, adjust

black float adjustment clip, and sliding float up or down on

metal float rod until water level at marked water line .5A

190

Float

Float Adjustment clip

Make sure the arrow on the green float on the white flush

valve is secure and pointing to #2. (Fig. 5B )

6. ADJUST OVERFLOW HEIGHT (If necessary) Adjust overflow tube so that the top is 20mm above the waterline. Push locking mechanism to the side and adjust tube height. Push locking mechanism back into position to lock tube height. See Fig.#6.

maxi

Fig. #5

(5B)

6. ( )

20mm

1037406-T01-A

Fig. #6

-5-

7. CONNECT PUSH BUTTON Put large flange through hole in lid. Screw retaining ring onto flange. Turn the screw inside the push button flange to secure tank lid to flush valve assembly. Make certain that the flush valve assembly is adjusted high enough that the button touches the assembly. Put green and white push rods into corresponding holes and trim flush with the top of the flange. Install flush buttons.

See Fig. 7 . See Fig. 8 .

See 6 .

1&1 1/2 tour

1037406-T01-A

Fig. #7

-6-

8. Install seat with hardware provided.

See Fig.#8.

8. 8

1037406-T01-A

Fig. #8

-7-

TROUBLESHOOTING CHART

SYMPTOMS PROBABLE CAUSES

1. Float valve turns on/off by itself without toilet being flushed

2. Float valve continues to run, allowing water to enter tank.

3. Incorrect water level height.

4. Long or noisy tank fill

A. Flush valve seal worn, dirty or damaged.

A. Foreign particles lodged under the float valve

seal (located under float valve cap)

B. Float valve seal (located under float valve cap)

may be cracked or split.

C. Tank water level set above overflow level.

A. Float height incorrect.

A. Plugged valve inlet or supply line.

CORRECTIVE ACTION

A. Inspect, clean and, if necessary replace seal.

A. Shut off water supply; remove float valve cap

assembly by rotating 1/8 turn counterclockwise. Cover uncapped lower valve unit with an inverted cup (holding it to prevent overspray), and turn water on and off a few times. Clean float valve seal surface (located under float valve cap). Replace float valve cap assembly by engaging lugs and rotating 1/8 turn clockwise. Turn water on. Install filter in supply line to prevent recurring problems.

B. Replace seal.

C. During fill cycle, hold float under water a few

seconds to allow it to fill with water ballast. Adjust float by squeezing float adjustment clip, and sliding float up or down on float rod until water level is at marked water line.

A. Adjust float by squeezing float adjustment clip,

and sliding float up or down on float rod until water leve is at marked water line.

A. Perform corrective action 2.A.

5. Poor flush.

6. Toilet overflows.

1. /

A. Water usage is too low. B. Trapway obstructed. C. Soil pipe or vent is obstructed. D. Supply shut-off valve not fully open.

A. Toilet trapway is obstructed. B. Soil pipe or vent is obstructed.

A. (

)

B. ( ) C.

A. Adjust the water tank level. B. Unclog trapway. C. Clear obstruction from soil pipe or vent. D. Open supply shut-off valve.

A. Use plunger to unclog. B. Clear obstruction from soil pipe or vent pipe.

1/8 ()

()

1/8

B. C.

6. A.

1037406-T01-A

A. B. C. D.

A. 2AA.

A. B. C. D.

A. B.

-8-

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes in the toilet rim are kept clean to ensure proper bowl flushing. Toilet bowl cleaners should be used at least once a week. Use a long-handled brush to clean the rim holes, and to clean as far into the trap as possible to prevent mineral deposits from forming.

Most toilet bowl cleaners are not harmful to the vitreous china surface of the toilet bowl. Please follow the bowl cleaner manufacturers instructions carefully.

Do not use abrasive cleaners or solvents.

WARNING: Risk of property or product damage.

Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage.

Kohler Company shall not be responsible or liable for any damage to these tank fittings caused by the use of cleaners containing chlorine (calcium hypochlorite).

LIMITED ONE-YEAR WARRANTY

Plumbing Fixtures and Fittings Limited One-year Warranty

Kohler plumbing fixtures and fittings are warranted to be free of manufacturing defects.

This product is warranted for one year from date of purchase. Kohler China will be responsible for any problems caused by manufacturing defects provided with the invoice. Kohler China will, at its election, repair, replace or make appropriate adjustment where Kohler China inspection discloses any such defects occurring in normal usage within one year after purchase.

Implied warranties including that of merchantability and fitness for a particular purpose are expressly limited in duration to the duration of this warranty, Kohler China disclaims any liability for special, incidental or consequential damages. Damages to the product caused by misuse, abuse and installation that is not in accordance with the owner's manual are not covered by this warranty.

To obtain quick warranty service, please contact your dealer, or write to Kohler China. (Original sales receipt must be provided as the proof of purchase.)

Kohler China Investment Company Ltd. Central Customer Service Center 19/F, Shanghai Square, 138 Huai Hai Road, Luwan District, Shanghai, PRC Zip Code: 200021

This is our exclusive written warranty.

1037406-T01-A

()

138

200021

-9-

ODEON

SERVICE PARTS PAGE

P/S-

VITREOUS CHINA P/S-TRAP TOILET

P-TRAP 180mm K-8711T S-TRAP 255mm K-8753T

S-TRAP 305mm K-8766T

82984-B Float Valve Assy.

83143 Seal

G1/2 Shank

84929 Washer

1021421 Flush Valve Body

1004136-** Tank

1021425 Flush Button Support

1021424 Flapper

Cover

Model

Bowl

Tank

Seat

1004140 Flush Button Assy.

1021422 Green Flush Stick

1021423 Black Flush Stick

1021426 Overflow Tube Fixture

53154 Gasket

1007746 Nut

K-8711T K-8753T K-8766T

K-8709T K-11184T K-8767T

K-8710T K-8710T K-8710T

K-8741T-** K-8741T-** K-8741T-**

1004139 Flush Valve Assy.

84897 Locknut

1004142 Mounting Plate & Bolts

1004141 Floor Mounting Kit

1000687 Tank/Plate Gasket

1032265 Gasket

1021448 Hardware Assembly

1021449 Screw

1021446 Left Hand Hinge

1021447 Right Hand Hinge

K-8741T-** Odeon Seat

1037406-T01-A

** Color code must be specified when ordering.

-10-

Kohler K-8741T, K-8767T, K-11184T, K-8753T, K-8709T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual