Kohler K-872, K-870 User Manual

Page 1
Homeowners Guide
Bath Whirlpool
K-870, K-872
1019486-5-A
Page 2
Operating Instructions
ELECTRIC SHOCK, OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING: When using electrical products, basic precautions should always be followed, including the following:
DANGER: Risk of personal injury. To re duce the risk
of injury, do not permit children to use this unit unless they are closely supervised at all times.
WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the whirlpool.
WARNING: Risk of electric shock. Do not permit electric appliances (such a s a hair dryer, lamp, telephone, radio, or television) within 5’ (1.5m) of this whirlpool.
WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical history should consult a physician before using a whirlpool equipped with a heater.
An equipment grounding terminal is provided in the field wiring compartment. T o reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply panel with a conductor equivalent in size to the circuit conductors supplying this whirlpool.
A pressure wire connector is provided on the exterior of the pump or control within this unit to permit connection of a bonding conductor between this unit and all other exposed metal in the vicinity , as needed to comply with local requirements.
Use this whirlpool only for its intended purpose as described in this manual. Do not use attachments not recommended by the manufacturer.
Never drop or insert any object into any opening. Do not operate this unit without the guard (cover) over
the suction fitting. The whirlpool must be connected only to a supply circuit
that is protected by a Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB). Such a GFCIorELCBshouldbeprovidedbytheinstallerand should be tested on a routine basis. T o test the GFCI or ELCB, press the test button. The GFCI or ELCB should interrupt power . Press the reset button. Power should be restored. If the GFCI or ELCB fails to operate in this manner , the GFCI or ELCB is defective. If the GFCI or ELCB interrupts power to the bath without the test button being pressed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the problem corrected by a qualified service representative before using.
SAVE THESE INSTRUCTIONS
WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.
Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6_F(37_C). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c) unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to exit the bath, and (f) unconsciousness resulting in the danger of drowning.
IMPORTANT! Flush your whirlpool system twice a month or more depending upon usage, as described on Page 6.
Do not allow the water temperature in the whirlpool to exceed 104_F(40_C). Keep small objects such as bath toys and bathing accessories out of the whirlpool while the unit is running. Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use heavy, vegetable-based shampoos or bath oils. Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath oil to foam excessively. For this reason, please don’t use these products during whirlpool operation.
1019486-5-A
2
Kohler Co.
Page 3
Table of Contents
Thank Y ou 4...................................
Your Kohler Whirlpool 4.........................
User Keypad & Whirlpool Modes/Features 5........
Optional Remote Control 5.......................
Operating Y our Whirlpool 5......................
Care and Cleaning 6............................
Warranties -- U.S.A. and Canada 7................
One-Year Warranty -- Mexico 9...................
Troubleshooting 10..............................
Service Parts 12................................
Kohler Co.
3
1019486-5-A
Page 4
The user keypad allows you to turn the whirlpool and heater on and off and regulate the water flow
Adjustable jets allow you to adjust the air and water flow and direction
The heater helps maintain the water temperature up to 104_F(40_C)
The bath provides a reservoir for the hydro-massage action
NOTE: Bath shown for illustrative purposes. Your bath model may vary.
The pump motor provides quiet, variable speed power to circulate the water
Thank You For Choosing Kohler
Thank you for choosing The Bold Look of Kohler. Kohler craftsmanship offers you a rare combination of proven performance and graceful sophistication that will satisfy you for years to come. The dependability and beauty of your new whirlpool will surpass your highest expectations. We’re proud of our whirlpools here at Kohler, and we know you will be too.
Please take a few minutes to study this Homeowners Guide before you use your whirlpool. Pay special attention to the Care and Cleaning instructions on Page 6.
All information in this manual is based upon the latest product information available at the time of publication. At Kohler, we constantly strive to improve the quality of our products. We reserve the right to make changes in product characteristics, packaging, or availability at any time without notice.
Your Kohler Whirlpool
Your new whirlpool is designed to stimulate, invigorate, and energize your body with comforting hydro-massage therapy. The whirlpool consists of the following components:
S Bath - acts as a reservoir for water, and provides a location for the hydro-massage action. S User Keypad - located within easy reach, the keypad allows you to turn the whirlpool and heater on and off and
regulate the water flow through the jets.
S Pump Motor - provides quiet, variable speed power to circulate the water and create the soothing hydro-massage
action.
S Adjustable Jets - positioned to optimize their hydro-massage effect, the jets allow you to adjust the air and water
flow and control the flow direction as you desire.
S Heater - designed to automatically help maintain the temperature of the water up to 104_F(40_C) to enhance
your hydro-massage experience. The heater turns on automatically when the whirlpool is operating, and turns off when the pump motor is turned off. The heater may be turned off, through the keypad, at any time while the pump is operating.
1019486-5-A
4
Kohler Co.
Page 5
Heater On/Off
Heater Indicator Light
Increases Flow
Indicator Bar-­Shows water flow volume
Turn the jet trim ring clockwise to decrease the flow
Power On/Off
Lighted User Keypad
Decreases Flow
Turn the jet trim ring counterclockwise to increase the flow
User Keypad and Whirlpool Modes/Features
S Power- Turns the whirlpool pump on and off. S Up Arrow- Increases the water flow. S Down Arrow- Decreases the water flow. S Heater- The heater automatically engages when the whirlpool is turned on. You may turn the heater off by
pressing the heater button. Press the button a second time to turn the heater back on.
S Indicator Bar- Shows the water flow volume.
Optional Remote Control
If you purchased a remote control, please refer to the H omeowners Guide packed with your remote control for detailed information.
Operating Your Whirlpool
- Turn the jet trim fully counterclockwise. Position the jet nozzles so they face down toward the basin.
NOTE: The water temperature in the whirlpool should never exceed 104_F(40_C). A built-in heater automatically maintains the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104_F(40_C). The heater will disengage at higher temperatures.
- Close the drain, and fill the whirlpool to a level at least 2” (5cm) above the top of the highest jet. Use your hand to test the water temperature for comfort and safety, then carefully enter the bath.
- Press Power to turn on the whirlpool. The whirlpool will start at medium volume. The heater will also turn on and the heater icon will illuminate.
- Increase or decrease the water flow by pressing the up or down arrows on the keypad. An indicator bar in the center of the keypad shows the water flow volume.
- Adjust the jets f or optimum air/water mixture. Turn the jet trim clockwise to reduce the flow, and counterclockwise to increase the flow. Position the jet nozzles to direct the water flow as desired to maximize your
hydro-massage experience.
- The heater automatically engages when the whirlpool is turned on. You may turn the heater off by pressing the heater button on the keypad. Press the button a second time to turn the heater back on.
- Press Power a second time to turn off the whirlpool. NOTE: Your whirlpool will automatically stop after approximately 20 minutes of continuous operation. You can
restart the whirlpool, if you desire, by pressing Power.
- Carefully exit the bath, and open the drain to empty the whirlpool. NOTE: If the whirlpool does not function properly, please refer to Troubleshooting on Page 10.
Kohler Co.
5
1019486-5-A
Page 6
Care and Cleaning Instructions
Cleaning Your Kohler Cast Iron Whirlpool
- Rinse the whirlpool thoroughly after each use and u se a soft cloth to wipe it dry. If the surface becomes dirty, use a general purpose cleaner such as Scrub Free
Original, FantasticRAll Purpose, Mr. Clean Top Job, Formula 409RAll Purpose, LysolRBasin, Tub & Tile Cleaner or Scrubbing Bubbles
R
Bathroom Cleaner.
IMPORTANT! Use water soluble cleaners (dissolve 100% in water). Cream-based cleaners may have a tendency to build up, reducing the friction on slip-resistant surfaces.
- BCD Rog 3 Non-Acid Bathroom Cleaner may be used on the Safeguard surface or whirlpool. It is not sold commercially. Call 1-800-470-8337 to order. A soft nylon brush may be used on the Safeguard surface.
- Do not use steel wool, wire brushes or abrasive sponge pads. In the rare occurence of stubborn stains, use abrasives or abrasive cleaners sparingly, but not on the Safeguard surface on the bottom of the whirlpool.
- For occasional rust removal you may use Whink
Cleaning Your User Keypad and Remote Control
- Use a soft cloth to wipe the keypad and remote control after each use. If the surface becomes dirty, use a non-abrasive soap and warm water to clean.
Flushing Your Whirlpool System
Flush your whirlpool system twice a month or more, depending upon usage. Use the following sequence:
- Turn the jet trim rings fully clockwise to remove air induction.
- Fill the whirlpool with warm water to a level at least 2” (5cm) above the highest jets, or leave water in the
whirlpool after using.
- Add 2 tablespoons (30 ml) of a low-foaming dishwasher detergent and 20 ounces (590 ml) of household bleach (5% - 6% sodium hypochlorite) to the water.
- Run the whirlpool for 5 to 10 minutes. Turn off the whirlpool and drain.
- If desired, rinse the bath surfaces with water.
- Rinsethesurfacesofthejets,faucet,handrails,drain,etc.andwipethemdrywithasoftcloth.
R
Mildew Stain Remover, Clorox Clean-UpR,GlassPlusR,Windex
R
Rust & Iron Stain Remover or Muriatic Acid.
R
1019486-5-A
6
Kohler Co.
Page 7
Limited One-Year Warranty -- USA and Canada
KOHLERR plumbing fixtures, faucets and fittings are warranted to be free of defects in material and workmanship for one year from date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses any such defects occurring in normal usage within one year after installation. Kohler Co. is not responsible for removal or installation costs.
To obtain warranty service, contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or E- tailer, or by writing Kohler Co., Attn: Customer Service Department, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER from within the USA, 1-800-964-5590 from within Canada and 001-877-680-1310 from within Mexico.
Implied warranties including that of merchantability and fitness for a particular purpose are expressly limited in duration to the duration of this warranty. Kohler Co. disclaims any liability for special, incidental or consequential damages. Some states/provinces do not allow limitations on how long an implied warranty lasts,
or the exclusion or limitation of special, incidental or consequential damages so these limitations and exclusions maynotapplytoyou.Thiswarrantygivesyouspecificlegalrights.Youmayalsohaveotherrightswhichvary from state/province to state/province.
This is our exclusive written warranty.
Notes:
1. There may be variation in color fidelity between catalog images and actual plumbing fixtures.
2. Kohler Co. reserves the right to make changes in product characteristics, packaging or availability at any time without notice.
COPYRIGHT E 1999, 2000, 2001, 2002 BY KOHLER CO.
Kohler Co.
7
1019486-5-A
Page 8
Lifetime Limited Warranty -- USA and Canada
Kohler warrants the cast iron components of this product manufactured after February 10, 2000, to be free of defects in material and workmanship during normal residential use for as long as the original consumer purchaser owns his/her home. Gloss reduction, scratching, staining and alkaline etching, of the finish over time due to use, cleaning practices or water or atmospheric conditions are not manufacturing defects but are indicative of normal wear and tear. This warranty applies only for KOHLER Cast Iron product installed in the United States of America, Canada and Mexico.
If a defect is found in normal residential use, Kohler Co. will, at its election, repair, replace or make appropriate adjustment. Damage caused by accident, misuse, or abuse is not covered by this warranty. Improper care and cleaning will void the warranty. Proof of purchase (original sales receipt) must be provided to Kohler with all warranty claims. Kohler Co. is not responsible for labor charges, installation, or other incidental or consequential costs. In no event shall the liability of Kohler exceed the purchase price of the product.
If the cast iron product is used commercially or is installed outside of North America, Kohler warrants the cast iron product to be free from defects in material and workmanship for one (1) year from the date the product is installed, with all other terms of this warranty applying except duration. All other components other than the enameled cast iron carry Kohler’s one- year limited warranty unless otherwise specified.
If you believe that you have a warranty claim, contact Kohler Co., either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing: Kohler Co., Attn.: Customer Service Department, 444 Highland Drive, Kohler, WI 53044, USA. Please be sure to provide all pertinent information regarding your claim, including a complete description of the problem, the product, model number, color, finish, the date the product was purchased and from whom the product was purchased. Also include your original invoice. For other information, or to obtain the name and address of the service and repair facility nearest you call 1-800-4-KOHLER from within the USA, 1-800-964-5590 from within Canada, and 001-877-680-1310 from within Mexico.
The foregoing warranties are in lieu of all other warranties, express or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Seller disclaims any liability for special, incidental or consequential damages. Some states/provinces do not
allow limitations on how long an i mplied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary, from state/province to state/province.
This is our exclusive written warranty.
1019486-5-A
8
Kohler Co.
Page 9
One-Year Warranty -- For Mexico
KOHLER CO. It is recommended that at the time of purchase, you verify that all accessories and components are complete in
this package. This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the date
of purchase as shown on the invoice or receipt.
1. Kohler Co. will only service its commercialized products through its authorized distributors.
2. To obtain warranty service, please present the invoice and corresponding warranty.
3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new replacement or an equivalent model (in those cases that the model has been discontinued) when the product is
beyond repair, without any charge to the consumer.
4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.
5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may substitute the warranty in the case that there is a discrepancy in the validity of the warranty.
EXCEPTIONS & RESTRICTIONS The Warranty will not be valid in the following cases:
1. When the product is not operated in accordance with the instructions concerning use and operation set forth in the owner’s manual or installation instructions, and when the recommendations and warnings included are not
observed.
2. When the product has been modified or dismantled partially or totally; or has been used in a negligent fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not authorized
by Kohler Co.
3. Thiswarrantydoesnotcoverthedamagesasaresultofdisaster such as fire or acts of God, including flooding, earthquake, or electric storms, etc.
To obtain a list of distributors in your area where you can exercise your rights under this warranty, please call 001-877-680-1310.
KOHLER CO., KOHLER, WI 53044 U.S.A.
IMPORTER:
INTERNACIONAL DE CERÁMICA, S.A. DE C.V. AV. CARLOS PACHECO NO. 7200
Kohler Co.
9
1019486-5-A
Page 10
Troubleshooting Procedures
p
g
ringisrotated
jet
t
y
p
y
p
p
p
This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor.
Troubleshooting the Whirlpool System
Symptoms Probable Causes Recommended Action
1. User keypad does not illuminate when power button is pressed or outer
is rotated.
rin
2. Motor starts, but all
sareno
functioning.
3. User keypad is illuminated, but does not respond to buttons or ring.
.
A. No power to control. A. Check wiring and connect power. If
problem persists, refer to
installer/dealer. B. GFCI or ELCB tripped. B. Reset GFCI or ELCB. C. Wiring harness from user keypad to
control is loose, disconnected or damaged.
D. Faulty user keypad. D. Replace user keypad. Refer to
E. Faulty control. E. Replace control. Refer to installer/dealer. A. Jet is closed. A. Rotate jet trim counterclockwise to open.
B. Jet not installed correctly. B. Reinstall jet; check for O-ring damage.
C. Jets are blocked. C. Remove blockage. A. Control program is locked. A. Reset GFCI or ELCB. B. Wiring harness from user keypad to
control is loose, disconnected or damaged.
C. Faulty user keypad. C. Replace user keypad. Refer to
D. Faulty control. D. Replace control. Refer to installer/dealer.
C. Check wiring for proper connections.
Replace wiring harness if necessary.
Refer to installer/dealer.
installer/dealer.
B. Check wiring for proper connections.
Replace wiring harness if necessary.
Refer to installer/dealer.
installer/dealer.
4. User keypad indicator barkeeps scanning at power-up.
5. User keypad is illuminated, but pump won’t start.
6. Motor runs but pump won’t prime (cavitates).
A. Control program is locked. A. Reset GFCI or ELCB. B. Wiring harness from user keypad to
control is loose, disconnected or damaged.
C. Faulty user keypad. C. Replace user keypad. Refer to
D. Faulty control. D. Replace control. Refer to installer/dealer. A. Power cord from pump to control is
loose, disconnected or damaged.
B. Faulty pump. B. Replace pump. Refer to installer/dealer. C. Faulty control. C. Replace control. Refer to installer/dealer. A. Pump is shimmed too high. A. Lower pump/control to subfloor level. B. Small air leak at pump inlet. B. Securely tighten nut(s) on intake side of
C. Faulty motor/pump. C. Replace motor/pump. Refer to
D. Faulty control. D. Replace control. Refer to installer/dealer.
B. Check wiring for proper connections.
Replace wiring harness if necessary. Refer to installer/dealer.
installer/dealer.
A. Check wiring for proper connections. If
problem persists, refer to installer/dealer.
pump.
installer/dealer.
1019486-5-A
10
Kohler Co.
Page 11
Troubleshooting continued
but
t
feat
t
qpp
7. Pump stops before 18 minutes.
8. Pump does not automatically stop after 22 minutes.
9. Pump won’t turn off when the power
on on user
keypad is pressed.
10. Pump operates but variable speed
uredoes no
work.
11. Bath water cools while pump is operating.
A. GFCI or ELCB tripped. A. Identify source of fault, and correct.
Reset GFCI or ELCB. B. Suction is blocked. B. Remove obstruction. C. Jets are blocked. C. Remove blockage. D. Motor overheated and protection
device activated.
D. Check for blockage at suction and/or
jets. Remove blockage and allow motor
to cool. A. 20-minute timer inadvertently
A. See service manual.
disabled.
A. Faulty user keypad. A. Replace user keypad. Refer to
installer/dealer.
B. Faulty control. B. Replace control. Refer to installer/dealer.
A. Faulty motor/pump. A. Replace motor/pump. Refer to
installer/dealer.
B. Faulty control. B. Replace control. Refer to installer/dealer.
A. Water temperature above 104_F
A. Allow bath water to cool.
(40_C). B. Heater is turned off on user keypad. B. Turn heater on. C. Wiring from heater to control i s loose,
disconnected or damaged.
C. Check wiring for proper connections.
Refer to installer/dealer. D. Faulty heater. D. Replace heater. Refer to installer/dealer. E. Faulty control. E. Replace control. Refer to installer/dealer.
12. Noisy operation. A. Pump banding straps have not been cut.
B. Dry or dislodged jet O-ring (squeal). B. Remove jet, replace and lubricate O-ring,
13. Remote control (if
equipped) does not work.
A. Batteries improperly installed or
dead.
B. Antenna on wiring harness is
damaged.
C. Remote control not programmed
correctly.
D. Faulty remote control. D. Replace remote control. E. Faulty control. E. Replace control. Refer to installer/dealer.
A. Cut pump banding straps with tin snips.
and reinstall jet.
A. Replace batteries.
B. Replace wiring harness. Refer to
installer/dealer.
C. See homeowners guide or service
manual.
Kohler Co.
11
1019486-5-A
Page 12
94496 (Curved) 94497 (Flat)
Pillow Kit
94726-A (White) 94726-B (Black)
Cover
1019439
Sensor
93823
Nut
93848
Elbow
93948-A1 (8-3/8”/21.3cm) 93948-B1 (9-7/8”/25.1cm) 93948-C1 (6-7/8”/17.5cm) 93948-D1 (6”/15.2cm) 93948-E1 (4-5/8”/11.7cm)
Hose
94275-A
Butterfly Valve
C
1016466
Motor
93542
Gasket
63149
Screw
93931
Screw
93590-A
Manifold
1016534 (Ports Facing Left) 1016536 (Ports Facing Right) 1016535 (Waterscape & Vigora)
Neck Valve Assy.
96956
Butterfly
Cast Iron Shell Neck Valve Hardware
50506
Screw
93511**
Cover
63270
Washer
60170
Nut
Port
1018965
Adapter
1000054
Screw
91820
Sleeve
1010029
Tee
94377 (Curved) 94495 (Flat)
Pillow
94387-A
Plate
60982
Screw
91819
Grommet
94318-A2 (16-1/2”/41.9cm) 94318-B2 (15-1/2”/39.4cm) 94318-C2 (13-1/2”/34.3cm) 94318-D2 (7-1/2”/19.1cm) 94318-E2 (5-1/2”/14cm) 94318-F2 (18-1/4”/46.4cm) 94318-G2 (10-1/2”/26.7cm)
Hose
C
Acrylic Shell Neck Valve Hardware
95045
Screw
90153
Nut
64212
Washer
91819
Grommet
Service Parts
1019486-5-A
60980
O-Ring
**Finish/color code must be specified when ordering.
12
91820
Sleeve
Kohler Co.
Page 13
93836 (1/2”) 93838 (1”) 93839 (1-1/4”) 94853 (1-1/2”)
Tube (w/Couplings)
1003065
Suction Flange Removal Tool
65054**
Screw
96708
Flange
65226**
Suction Cover Plug
73518
Plug
65886 (Acrylic and FRP) 60050 (Cast Iron)
Gasket
96895** (Colored Finishes) 65061** (Metal Finishes)
Cover
91967
Check Valve
93685
Housing
67665
Plug
94469
Flange Removal Tool
67429
Flange
34353
O-Ring
Single Jet For Whirlpools With 5 or Less Jets
88532** (Colored Finishes)
60394-P
Silicone Lube Packet
88531** (Metal Finishes) Jet
Single Jet For Whirlpools With6orMoreJets
30739
Jet Tool
**Finish/color code must be specified when ordering.
88530** (Colored Finishes) 88529** (Metal Finishes)
Jet
67889
Jet Housing
65885 (Acrylic and FRP) 67668 (Cast Iron)
Gasket
Kohler Co.
13
1019486-5-A
Page 14
67065
Ground Lug
60320
Screw
60320
Screw
1018964
Bracket
90153
Locknut
61845-K
Copper Grounding Wire
1016957
2HPPump
1010677
Screw
1010676
Cover
93892
Electrical Box
60320
Screw
1010548
Volute
93893
Cover
67065
Ground Lug
93003
Strain Relief
1016958
Motor
1010673
Seal
1016960
Impeller
1019432
Carriage Bolt
90154
Nut
1019719
Connector
1005363
Nut
1010675
O-Ring
1019444-A (3/4”/1.9cm) 1019444-B (1-3/4”/4.4cm) 1019444-C (2”/5.1cm)
94821
O-Ring
1018661 (Neckjets) 1018663 (Neckjets & Backjets)
Control
**Finish/color code must be specified when ordering.
1019444-D (1-1/2”/3.8cm) 1019444-E (1”/2.5cm) 1019444-F (1-1/4”/3.2cm) 1019444-G (2-1/4”/5.7cm) 1019444-H (2-1/2”/6.4cm) 1019444-J (2-3/4”/7cm) 1019444-K (3”/7.6cm) 1019444-L (1/2”/1.3cm) 1019444-M (1/4”/6mm)
Spacer
1019445-A (1-3/4”/4.4cm) 1019445-B (2-3/4”/7cm) 1019445-C (3”/7.6cm) 1019445-D (2-1/2”/6.4cm) 1019445-E (2”/5.1cm) 1019445-F (2-1/4”/5.7cm) 1019445-G (3-1/4”/8.3cm) 1019445-H (3-1/2”/8.9cm) 1019445-J (3-3/4”/9.5cm) 1019445-K (4”/10.2cm) 1019445-L (1-1/2”/3.8cm) 1019445-M (1-1/4”/3.2cm)
Stud
1019447-A (1/4”/6mm) 1019447-B (1/2”/1.3cm) 1019447-C (3/4”/1.9cm)
Isolation Mount
1019486-5-A
14
Kohler Co.
Page 15
67065
Ground Lug
60320
Screw
60320
Screw
1018964
Bracket
1001794
Locknut
61845-K
Copper Grounding Wire
1016953
1.5 HP Pump
1010676
Cover
1010677
Screw
93892
Electrical Box
60320
Screw
1010548
Volute
93893
Cover
67065
Ground Lug
1019433
Carriage Bolt
93003
Strain Relief
90153
Nut
1016954
Motor
1010673
Seal
1013755
Impeller
1019719
Connector
1005363
Nut
1010675
O-Ring
1019444-A (3/4”/1.9cm) 1019444-B (1-3/4”/4.4cm) 1019444-C (2”/5.1cm) 1019444-D (1-1/2”/3.8cm)
94821
O-Ring
**Finish/color code must be specified when ordering.
1019444-E (1”/2.5cm) 1019444-F (1-1/4”/3.2cm) 1019444-G (2-1/4”/5.7cm) 1019444-H (2-1/2”/6.4cm) 1019444-J (2-3/4”/7cm) 1019444-K (3”/7.6cm) 1019444-L (1/2”/1.3cm) 1019444-M (1/4”/6mm)
Spacer
1018660
Control
1019446-A (1-3/4”/4.4cm) 1019446-B (2-3/4”/7cm) 1019446-C (3”/7.6cm) 1019446-D (2-1/2”/6.4cm) 1019446-E (2”/5.1cm) 1019446-F (2-1/4”/5.7cm) 1019446-G (3-1/4”/8.3cm) 1019446-H (3-1/2”/8.9cm) 1019446-J (3-3/4”/9.5cm) 1019446-K (4”/10.2cm) 1019446-L (1-1/2”/3.8cm) 1019446-M (1-1/4”/3.2cm)
Stud
1019447-A (1/4”/6mm) 1019447-B (1/2”/1.3cm) 1019447-C (3/4”/1.9cm)
Isolation Mount
Kohler Co.
15
1019486-5-A
Page 16
1012653
Adapter
94821
O-Ring
1018709
Heater
1012916
Nut w/Screws
1011679
Gasket
1012977
Adapter
1012977
Adapter
1018710
Heater
1012916
Nut w/Screws
94821
O-Ring
**Finish/color code must be specified when ordering.
94821
O-Ring
1011679
Gasket
1019486-5-A
16
Kohler Co.
Page 17
1023381
Wrench
1013453
Spring
1020677
Gasket
65157
Nut
Carefully study decal and cover detail below for proper service part identification
1020678--A
Cover/Circuit Board (w/Wrench)
1020678-C
Cover/Circuit Board (w/Wrench)
1013452**
Dial Trim
1013497-A
Decal
1013499
Housing
91639
O-Ring
1020678-B
Cover/Circuit Board (w/Wrench)
1013497-B
Decal
1020678-D
Cover/Circuit Board (w/Wrench)
Kohler Co.
1013497-C
Decal
1020678-E
Cover/Circuit Board (w/Wrench)
**Finish/color code must be specified when ordering.
17
1013497-D
Decal
1013497-E
Decal
1019486-5-A
Page 18
1020679-A
Cover/Circuit Board
1013469**
Trim Ring
1013460
Housing
59588
Screw
94110
O-Ring
1013459-A
Decal
1019486-5-A
**Finish/color code must be specified when ordering.
18
Kohler Co.
Page 19
1013822-A
Remote w/Stand
1023091**
Cap
1013464-A
Decal
1013471**
Stand
1013822-B
Remote w/Stand
1020679-A
Remote
1013464-B
Decal
Kohler Co.
1020679-B
Remote
**Finish/color code must be specified when ordering.
19
1019486-5-A
Page 20
1019486-5-A
USA: 1-800-4-KOHLER
Canada: 1-800-964-5590
Mexico: 001-877-680-1310
kohler.com
E2003 Kohler Co.
20
1019486-5-
A
Kohler Co.
Loading...