Kohler K-8741T, K-8767T, K-11184T, K-8753T, K-8709T User Manual

...

BEFORE YOU BEGIN

ODEON

INSTALLATION INSTRUCTIONS

P/S-

VITREOUS CHINA P/S-TRAP TOILET

P-TRAP 180mm K-8711T S-TRAP 255mm K-8753T

S-TRAP 305mm K-8766T

Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation . This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.

All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time withoutnotice.

These instructions contain important care, cleaning, and warranty information-please leave instructions for the

consumer.

ORDERING INFORMATION

Odeon P-trap 180mm Toilet K-8711T

Includes seat K-8741T-* Includes Bowl K-8709T Includes Tank K-8710T

Odeon S-trap 255mm Toilet K-8753T

Includes seat K-8741T-* Includes Bowl K-11184T Includes Tank K-8710T

Odeon S-trap 305mm Toilet K-8766T

Includes seat K-8741T-* Includes Bowl K-8767T Includes Tank K-8710T

Service parts

Fill valve K-82984-B Mounting Plate Assy K-1004142 Flush Valve Assy K-1004139

180mm K-8711T

K-8741T-*

K-8709T K-8710T

255mm K-8753T

K-8741T-*

K-11184T

K-8710T

305mm K-8766T

K-8741T-*

K-8767T K-8710T

K-82984-B K-1004142 K-1004139

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 155mm (6-1/8") centers.

Passageways is 60mm (2-3/8").

Water depth from rim is 245mm (9-5/8")

Ensure that the new drain and shut-off valve have the

correct roughing-in dimensions. . Be very careful while working with vitreous china products.

Vitreous china can break or chip if the bolts or nuts are overtightened, or if carelessly handled. Carefully inspect the new fixture for any sign of damage.

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112. 19.2M).

See Fig.#1

1037406-T01-A

ASME(A112. 19.2M)

-1-

60mm(2-3/8")

528137

155mm(6-1/8")

245mm(9-5/8")

, 2004

TOOLS AND MATERIALS REQUIRED (Not supplied)

254mm adjustable wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Straight pipe coupling

Connection packing

Toilet supply shut-off valve, 10mm (3/8") recommended

()

254mm

10mm(3/8")

WARNING: Risk of external leakage.

The fill valve nut has been factory-tightened, wrench tighten 1/4 turn past finger tight.

NOTICE:

If no shut-off valve exists, install a shut-off valve

below the tank before installing the new toilet.

Flexible hose are recommended to connect the supply line to the fill valve. If you use a rigid connection, take care not to apply side forces to the bottom of the fill valve.

ROUGHING-IN

204

255

777 10

178

102

159

204

396

785 10

388

484

100

1/4

204

776 10

394

305

474

Unit:mm

392

102

698

429

337

390

158

P-trap

8711T

166

267

362

390

INSTALLATION

1. REMOVE EXISTING TOILET Turn off water supply. flush the toilet and use a sponge to remove the remaining water from the tank and bowl. Disconnect the supply shut-off valve (if present) and remove the old tank and bowl.

1037406-T01-A

S-trap

156

-2-

699

428

337

158

8753T

265

362

390

S-trap

()

155

736

433 344

162

8766T

259

363

Fig.#1

2. ASSEMBLE TANK BOLTS&WASHERS Slip bolt heads into mounting plate on bottom of tank. Place large foam washer on base of flush valve.

See Fig. #2a.

Place tank on bowl and attach with nuts and washers from under bowl.

See Fig.#2b.

NOTE:

Do not use white cement or high lime content cements to install this toilet. The expansion of cement due to a rise in temperature may make the toilet crack or cause damage. Kohler is not responsible for any damage caused by installation with the use of cement.

Fig.#2a

3. SELECT P-TRAP OR S-TRAP

to installation your toilet according to the drain and shut-off valve's Roughing-in dimensions.

Fig.#2b

S-trap installation

Fig.#3a

120

255/305

P-trap installation

255/305

180

120

0 8 1

Fig.#3b

1037406-T01-A

-3-

+ 7 hidden pages