Kohler K8304KSLNA Specifications

Features

•

Includes valve body, pressure balance cartridge, rough-in guide and mud guard

•

1/2" Universal NPT & direct sweat inlets & outlets, with stops

•

Service stops supplied loose (not factory installed in valve body)

- ready for making sweat connections to valve inlets

•

Service stops include integral check valves

•

5.0 gpm (18.9 l/min) maximum flow rate at 45 psi

•

Single lever design cycles from off through cold to hot

•

Provides temperature regulation and automatic anti-scald protection

•

One piece cartridge design simplifies installation and maintenance

•

Adjustable high temperature limit stop to control maximum water temperature

•

Requires valve trim to complete installation (sold separately).

Rite-Temp® Rite-Temp

Valve Body & Cartridge Kit Complete

K-8304-KSL

Codes/Standards

ASME A112.18.1/CSA B125.1 ASSE 1016/ASME A112.1016/CSA B125.16

Material

•

Forged De-zincification Resistant Brass body provides long term reliability and resistance to aggressive water conditions

Technology

•

Pressure-balancing diaphragm technology maintains outlet temperature within +/- 3 degrees Fahrenheit during water pressure fluctuations

Installation

•

Designed for use in standard, back to back and thin wall installations

•

Valve body features integral mounting locations and symmetrical valve inlets to simplify installation

•

Cartridge is reversible for installations where hot and cold supplies are reversed.

•

Rough-in guide designed for both standard and thin wall installations

•

Installed valve rough-in can be flushed and pressure tested to 150psi max (air or water) without cartridge, using K-10351 Test Cap

Optional Accessories

K-10350 Deep Rough-In Kit For K-8305 Cartridges K-10351 Test Cap For K-8300 Series Valve Bodies

KOHLER® Faucet Lifetime Limited Warranty

See website for detailed warranty information.

USA/Canada: 1-800-4KOHLER (1-800-456-4537) Kohler Co. reserves the right to make revisions without notice to product specifications. For the most current Specification Sheet, go to www.kohler.com. 2-3-2018 02:56

Ø 4-1/2" (114 mm)

2-15/16"

(75 mm)

2-3/16"

(56 mm)

9/16"

(14 mm)

Outlet Port

3-1/2"

(89 mm)

2-3/4"

(70 mm)

1-15/16"

(49 mm)

1-15/16"

(49 mm)

Max Finished Wall

Min Finished Wall

Inlet Port 1/2"-14 NPT

and 5/8" ID for 1/2"

Nominal Copper Tubing

Outlet Port

1/2"-14 NPT and 5/8" ID

for 1/2" Nominal

Copper Tubing

Ø 1"

(25 mm)

Cut Line

Ø 4" (102 mm)

5-7/8" (149 mm)

7/8" (22 mm)

Ø 5" (127 mm)

Cutout for finished walls

greater than 3/4" (19 mm)

Cutout for finished walls

less than 3/4" (19 mm)

Rite-Temp® Rite-Temp

Valve Body & Cartridge Kit Complete

K-8304-KSL

Technical Information

All product dimensions are nominal.

Shower Valve:

Notes

Install this product according to the installation instructions.

20 psi (1.4 bar)Min. pressure IN:

Avoid cross-flow conditions. Do not install shut-off device on either valve outlet.

Cap the shower outlet if deck-mount spout, diverter, or handshower is connected to the spout outlet.

Install straight pipe or tube drop of 7" (178 mm) to 18" (457 mm) with single elbow between the valve and wall-mount spout.

For finished walls greater than 3/4" (19 mm) and less than 1-1/2" (38 mm), install support(s) 2" (51 mm) from the stud face.

For finished walls greater than 1-1/2" (38 mm), install support(s) 3" (76 mm) from the face of the finished wall.