Kohler K-1496-H2 User Manual

RAPPORT

Features

Acrylic

•

1.5 hp variable-speed pump with 1.5 kW heater and

•

back-lit user keypad 6 Flexjets

•

Less all trim

• 72-3/8″ (183.8 cm) x 35-3/4″ (90.8 cm) x 24-1/2″

•

(62.2 cm)

Codes/Standards Applicable

Speciﬁed model meets or exceeds the following:

ASME A112.19.7M

•

ANSI Z124.1.2

•

IAPMO/UPC

•

Underwriters Laboratories (UL)

•

Speciﬁed Model

6’ BATH WHIRLPOOL

K-1496-H2

Colors/Finishes

0: White

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

Accessories

0: White

•

CP: Polished Chrome

•

PB: Vibrant®Polished Brass

•

NA: None applicable

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

Model Description Colors/Finishes

K-1496-H2 Bath whirlpool ❑ 0 ❑ Other_____

Required Accessories

K-9696 Jet trim kit ❑ CP ❑ PB ❑ Other_____

Recommended Accessories

K-7161-AF Pop-up drain ❑ CP ❑ PB ❑ Other_____

Optional Accessories

K-1179 Vinyl tiling-in bead (use when wall material contacts any top surface of bath) ❑ NA K-1491 Pillow ❑ 0 ❑ Other_____ K-1601 Footstop ❑ 0 ❑ Other_____

Additional Optional Accessories table is on page 2.

Product Speciﬁcation

The acrylic bath whirlpool shall be 72-3/8″ (183.8 cm) in length, 35-3/4″ (90.8 cm) in width, and 24-1/2″ (62.2 cm) in height. The bath whirlpool shall have six Flexjets, a 1.5 hp variable-speed pump, a 1.5 kW heater, and back-lit user keypad. The bath whirlpool shall be less all trim. The bath whirlpool shall be Kohler Model K-1496-H2-_______.

Page 1 of 2 1022397-4-

USA: 1-800-4-KOHLER

Canada: 1-800-964-5590

kohler.com

RAPPORT

Optional Accessories

K-1703 Remote control ❑ NA

Technical Information

Fixture*: Bathing well: Basin area 45″ (114.3 cm) x 26″ (66 cm) Top area 67″ (170.2 cm) x 31″ (78.7 cm) To overﬂow: Water depth 18″ (45.7 cm) Capacity 110 gal (416.4 L) Weight 123 lbs (55.8 kg) Drop-in cutout 70-3/4″ (179.7 cm) x 34-5/8″ (87.9 cm) * Approximate measurements for comparison only.

Pump: Hp kW V Hz A Variable-

speed

1.5 1.5 240 50/60 11

Required Electrical Service

Dedicated circuit required, protected with a Class A Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB):

Pump/control 220/240 V, 20 A, 50/60 Hz Locate the outlets behind the whirlpool and within

24” (61 cm) of the pump.

Installation Notes

Install this product according to the installation guide.

Floor support under whirlpool must provide for a minimum of 59 lbs (290 kg) loading.

Hot water supply should be 70% of capacity or greater. Installations will vary.

No change in measurements if connected with drain illustrated. (K-7161-AF or K-7161M-AF)

2" (5.1 cm)

36" (91.4 cm)

72-3/8" (183.8 cm)

3/4" (1.9 cm)

24-1/2" (62.2 cm)

1/4" (6 mm)

RAPPORT®6’ BATH WHIRLPOOL Page2of2

1022397-4-

8-1/2" (21.6 cm)

Product Diagram

Pump/Control Access 34" (86.4 cm) W x 15" (38.1 cm) H

35-3/4" (90.8 cm)

3-1/2" (8.9 cm)

1-1/2" OD

2-7/8" (7.3 cm)

3" (7.6 cm)