Kohler K-1375-RV, K-1375-L User Manual

REVIVAL

Features

Acrylic

•

Variable speed pump with 1.5 kW heater, back-lit

•

user keypad and remote control 6 Flexjets

•

Ten color-matched sequencing Bodyssage

•

8 effervescent ports

•

4 chromatherapy lights

•

240 V, 20 A electrical service

•

Drilled for required grab bars

•

Coordinating Revival

• 72″ (1829 mm) x 42″ (1067 mm) x 22″ (559 mm)

•

TM backjets

Suite

Codes/Standards Applicable

Speciﬁed model meets or exceeds the following:

ASME A112.19.7

•

ASTM E662

•

ASTM E162

•

UL 1795

•

CSA B45.5/IAPMO Z124

•

Speciﬁed Model

6’ EXPERIENCE BATH WHIRLPOOL

WITH SPA/MASSAGE PACKAGE

K-1375-LV

ALSO K-1375-RV

Colors/Finishes

0: White

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

Accessories

CP: Polished Chrome

•

PB: Vibrant®Polished Brass

•

Model Description Colors/Finishes

K-1375-LV Bath whirlpool with Spa/Massage Package – pump on left ❑ 0 ❑ Other_____ K-1375-RV Bath whirlpool with Spa/Massage Package – pump on right ❑ 0 ❑ Other_____

Required Accessories

K-9653 Grab bars (pair) ❑ CP ❑ PB ❑ Other_____

Recommended Accessories

K-7161-AF Adjustable pop-up drain ❑ CP ❑ PB ❑ Other_____

Product Speciﬁcation

The acrylic bath whirlpool shall be 72″ (1829 mm) in length, 42″ (1067 mm) in width, and 22″ (559 mm) in height. Product shall have 6 Flexjets, 8 effervescence ports, and 4 chromatherapy lights. Product shall have a variable speed pump, 1.5 kW heater, back-lit user keypad and remote control. Product shall have 10 color-matched sequencing Bodyssage backjets and 2 pulsating neckjets with pillow. Product shall be drilled for K-9653 grab bars (required) and UL listed. Product shall coordinate with Revival Suite. Bath whirlpool shall be Kohler Model K-1375-_______-_______.

Page 1 of 2 1023248-4-

USA/Canada: 1-800-4KOHLER

(1-800-456-4537)

www.kohler.com

REVIVAL

Technical Information

Required Electrical Service

Fixture*: Basin area: Bathing area, bottom 40″ (1270 mm) x 27″ (686 mm) Bathing area, top 61″ (1549 mm) x 32″ (813 mm) Weight 165 lbs (75 kg) To overﬂow: Water depth 16″ (406 mm) Capacity 90 gal (341 L) * Approximate measurements for comparison only.

Pump: kW V Hz A

1.5 240 50/60 15

Cut-out template 113311-7

No change in measurements with drain shown. (K-7167-AF)

Recommended faucet area.

4" (102 mm) Max

Dedicated circuit required, protected with Class A Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD):

Pump/control 220-240 V, 20 A, 50/60 Hz

Installation Notes

Install this product according to the installation guide.

Pump/piping protrudes beyond rim (see below).

Maximum deck thickness should not exceed 2″ (50 mm).

Floor support under whirlpool must provide for a minimum of 44 lbs/square foot (214 kg/square meter) loading.

Hot water supply should be 70% of capacity or greater. Installations will vary.

If installing a rim-mount faucet, make sure there is no interference with drain overﬂow and circulating system before drilling any holes. Consult local and national codes for minimum air gap requirements if installing a spout on the faucet deck.

Note: Pump/piping protrudes beyond rim.

1" (25 mm) Max

3" (76 mm) x 24" (610 mm) Flat Faucet Deck

36" (914 mm)

72" (1829 mm)

42" (1067 mm)

Pump/Control Access 34" (864 mm) W x 15" (381 mm) H Min

2-1/4" (57 mm)

1-1/2" OD

3" (76 mm)

Product Diagram

REVIVAL®6’ EXPERIENCE BATH WHIRLPOOL WITH SPA/MASSAGE PACKAGE Page2of2

1023248-4-

13-1/2" (343 mm)

6-1/2" (165 mm)

3-1/2" (89 mm)

22" (559 mm)

2-7/8" (73 mm)