SERVICE PARTS
INSTALLATION INSTRUCTIONS
BEITOUBEITOU
1234003
99876IN-4ND
Wall Mount
1228832
1231859
3015832
Lavatory Faucet
1241100**
3016092
99876IN-4ND
Wall Mount
Lavatory Faucet
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes.
4. Check for leaks before cover the pipes, repairs as needed.
5. Please ensure only apply water pressure test on the product, and empty the air in pipe and faucet thoroughly
before the test. Please ensure test pressure below 0.8MPa (8 bar) and test duration within 30 minutes.
HANDLE OPERATION
Lift handle gently. Turn clockwise for cold water, turn counter-colckwise for hot water.
STANDARD APPLICABLE
1234012
1234011
1234010
870992
1180881
20960
1234006**
1228823
1244920
3010643
870654
1111496
1234008
3010849
1080817
1223368
1223584
1223593
1231860
1223587**
1223586
1228835**
Special model meets or exceeds the following at date of manufacture: TIS
ROUGH-IN DIMENSIONS
59
27
233
94
46
G1/2˝
47~57 70
135
167105
**Color code must be specified when ordering
1261813-IN2-A 4
1261813-IN2-A
1
INSTALLATION
INSTALLATION CHECKOUT
How To Install The York
Do not take off guards(1) at this moment.
Determine where the york(2) will be located on the wall according to the
lavatory.
Connect the G1/2˝ supplies to the york. Please note that the side of the york
with red dot connects to the hot supply and towards right. The distance between
finished wall and supplies should be 47~57mm. Ensure that the gaps between
guards and finished wall are less than 5mm.
Increase hot and cold water supply pressures to 1MPa. Inspect for leaks.
NOTE: Make sure two guards are the same distance to the wall. Ensure the
centerlines of them are horizontal.
2
COLD
2
47~57mm
HOT
1
5mm Max.
Ensure that all connections are tight. Ensure that the handle is in the off
position.
1
Turn on the main water supply, and check for leaks. Repair as
needed.
CARE AND MAINTENANCE
Clean Rectifier and Aerator
If there is a lot of debris in the supply pipes or the quality of water is bad, it will
cause the flow in bad condition. Please clean the filter and aerator as following
steps:
Turn off the faucet. Take out the plugs(15). Remove the screws(17) with hex
wrench(16). Uninstall the spout(18) from body(4). Remove the insert(19) and
rectifier(20). Remove the aerator(22) by tool(21).
19
20
22
18
21
How To Install The Faucet
When the finished wall is completed, cut off the exposed guards from the
finished wall.
Shut off water supply. Remove plug(a) from base. Install two inlets(3) into two
holes of the body(4). Tighten two screws(5) to secure the body.
4
Flush the filter of rectifier and aerator. Check the filter and aerator whether is
intact, if damaged replace it.
Reassemble the spout and body: put the insert, rectifier and aerator into the
original position. Install the spout onto body and tighten the screws. Insert the
17
15
plugs.
16
3
4
a
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
5
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
1261813-IN2-A
2
1261813-IN2-A
3
Loading...