SERVICE PARTS
INSTALLATION INSTRUCTIONS
AVIDAVID
97345T-4 Single Handle Lavatory Faucet
97347T-4 Tall Single Handle Lavatory Faucet
97348T-4 Super Tall Single Handle Lavatory Faucet
1244428**
1344636**
46023
1331655
1343774
1343773
1310075
1080817
1249005
3022101**
1149430-A**
833730
3006148
97345T-4 Single Handle Lavatory Faucet
97347T-4 Tall Single Handle Lavatory Faucet
97348T-4 Super Tall Single Handle Lavatory Faucet
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. If possible, install this faucet before installing the lavatory.
3. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
4. Observe local plumbing codes.
5. Shut off the water supplies to the fitting.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, turn counter-clockwise for cold water.
STANDARD APPLICABLE
1146748
1231664
1231664
1231664
1167767**
1080817
1149432**
880406
1167771
834704
1228834
1176997
1167770
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
Special model meets or exceeds the following at date of manufacture: TIS
ROUGH-IN DIMENSIONS
173
148
45 Max.
567
3.5°
Ø51
Ø32~Ø38
G1/2˝
110
97.5
Ø58
138
89
Ø36.5
Ø31.75
135
176.5
Ø68
27
130
97345T-4
Ø43
Ø38
Ø51
45 Max.
66
452
148
Ø32~Ø38
G1/2˝
173
3.5°
110
97.5
Ø58
204
Ø36.5
Ø31.75
253
176.5
135
Ø68
27
130
66
Ø43
Ø38
97347T-4
1248990-2A-B 4
1248990-2A-B 1
393
45 Max.
Ø51
173
148
3.5°
Ø32~Ø38
263
312
110
97.5
Ø58
Ø36.5
176.5
Ø31.75
135
130
Ø68
27
Ø43
Ø38
66
19
16
17
18
14
15
Remove the latch(19) and retaining nut(16). Fit the
plastic washer(17) and retaining nut onto the ball
lever(18). Insert the ball lever assembly into the drain
lever hole and through the stopper hole. Tighten the
retaining nut.
Be sure that the ball lever(18) points to the back of the
lavatory, tighten the locknut(15) on the drain body by
wrench.
NOTE: Do not reposition the drain if plumbers putty
applied after the locknut is tightened, or you may break
the putty seal. Wipe away excess plumbers putty.
5
19
18
20
21
④③
How to Install the Lift Rod Kit
Select the connection of the drain and the lift rod
according the dimension of lavatory.
Way 1: Select the latch(19)
Insert the ball lever rod(18) into the bigger
hole(21) of the latch(19). Insert the lift rod into the
other hole of latch. Push the ball lever rod down
to the open position. Tighten the screw(20) on
the latch.
G1/2˝
INSTALLATION
5
2
8
How to Install the Spout
If needed to take off the hoses to repair, reinstall and
tighten them by hand. Install the mounting studs(2)
onto the faucet body base(3). Insert lift rod(5) to the
hole at the rear of the body. Slide the washer(4) over
the flexible hoses(1) and mounting studs, and into
the groove at the bottom of the faucet body.
Insert the faucet assembly into the lavatory hole.
Position the faucet. From underside of the lavatory,
place the brackets(6, Rubber washer is on the top)
onto the mounting studs. Tighten the nuts(7) by
wrench(8) to secure the faucet.
Attach the hoses to water supplies. The hose with
"COLD" label connects to cold water.
3
4
1
6
7
① ②
97348T-4
Apply Plumbers Putty
11
12
14
13
25
10
9
15
10
How to Install the Drain
Remove stopper(11), flange(10), washer(9) and
tailpiece(25) from drain body(13). Supply enough
tape or sealant to tailpiece thread. Reinstall the
tailpiece. Insert drain body kit into the lavatory from
underside, and make sure the drain lever hole(14)
facing to the back of the lavatory. Screw the flange
with washer into the drain body. Tighten the
locknut(15) by hand from the underside of the fixture.
NOTE: If needed, apply a ring of plumbers putty
around the underside of the drain flange(10), instead
of using washer(9).
Place stopper(11) into drain body aligning the flat
side of stopper hole(12) with the drain lever hole.
15
25
26
⑥
23
5
24
22
18
18
⑤
How to Install the Drain Shroud
Way 2: Select the link kit(24, 22 & 23).
According to the lift rod length, bend the link(22).
Connect the link onto ball lever rod with "V" clip(23).
Slide lift rod(5) into the hole on link. Push the ball lever
rod(18) down to the open position. Tighten thumb
screw(24).
Slide drain shroud(26) with slot facing toward the
back, up over tailpiece(25) and around ball lever
rod(18), until contact with locknut(15) on the drain.
NOTE: At this point, tighten the drain shroud.
Connect the tailpiece to the trap. The tailpiece
should extend 25mm to 40mm into the trap.
INSTALLATION CHECKOUT
Ensure that all connections are tight. Ensure that the handle is in the off position.
Open the drain. Turn on main water supply and check for leaks. Repair as
required.
28
27
Remove aerator(28) by key(27). Turn the faucet handle on and run hot and cold
water through spout about one minute to remove any debris. Remove any debris
from aerator. Shut faucet off and reinstall aerator.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
1248990-2A-B 2
1248990-2A-B 3
Loading...