SERVICE BULLETIN
Kodak
Eastman Kodak Company, Health Imaging, Rochester, New York 14650
SERVICE BULLETIN NO. 277
3066
MULTILOADER
Kodak
3053
3443
MULTILOADER 700/700 PLUS SIDE-BY-SIDE KIT
Kodak
Kodak
MULTILOADER 700 PLUS
MULTILOADER 700
Type 1 Required Modifications Available
Mods No. 1 and 2 for the
Mod No. 31 for the
Mod No. 2 for the
Kodak MULTILOADER 700 PLUS, Modification No. 1
Purpose:
Serial Number:
Installation Time:
Instructions:
Part Number:
To install a new DOOR INTERLOCK ACTUATOR ASSEMBLY for safety
purposes.
50 Hz 3000 - 3100
60 Hz 7000 - 7075
0.5 hours
MA3443-1
9280406
Kodak
Kodak
Kodak
MULTILOADER 700 PLUS
MULTILOADER 700
MULTILOADER 700/700 PLUS SIDE-BY-SIDE KIT
March 1998
Kodak MULTILOADER 700 PLUS, Modification No. 2
Kodak MULTILOADER 700, Modification No. 31
Purpose:
Serial Number:
Installation Time:
Instructions:
Part Number:
© Eastman Kodak Company 7C8750
To install a HOSE LOOP at the COMPRESSOR to prevent the flow of condensation
back into the COMPRESSOR. This Mod applies to both the MULTILOADER 700
and 700 PLUS.
All MULTILOADER 700s
MULTILOADER 700 PLUS 50 Hz 3000 - 3348
MULTILOADER 700 PLUS 60 Hz 7000 - 7225
0.5 hours
MA3053-31
9286496
Repair Kits Available
The REPAIR KIT 9280706 for the MAGAZINE DOOR SPRING is now available. If the MAGAZINE DOOR for
the Kodak MULTILOADER 700 PLUS does not open, the MAGAZINE DOOR SPRING might be the problem. An
adjustment to the SPRING will not permanently correct the problem. To correct the condition, install the new
SPRING that is now being installed in the MULTILOADER 700 PLUS, starting with serial number 3353, 50 Hz,
and serial number 7239, 60 Hz.
The FILM OUT OF CASSETTE B6 SENSOR, 9181106 for the Kodak MULTILOADER 700 is no longer available.
Use REPAIR KIT 9194416. This kit
includes a TRANSMITTER and RECEIVER. The RECEIVER has below it a BOARD with 2 test points. These test
points are used for the adjustment of the new SENSOR. No adjustments are made on the A9 BOARD, making this
setup simpler. Installation and adjustment instructions are packed with the REPAIR KIT for the SENSOR.
cannot be used in a MULTILOADER 700 PLUS. The new SENSOR kit
Kodak
MULTILOADER 700 and 700 Plus
F9 FUSE Blowing Problem
The field has experienced problems with the COMPRESSOR F9 FUSE blowing for no apparent reason. This
problem is most likely caused by the MANOMETRIC PRESSURE SWITCH, S28. When the correct pressure is
reached, the COMPRESSOR is switched off by S28 and the PRESSURE HOSE is vented through the BLEEDER
VALVE, SV7. If the MANOMETRIC SWITCH is bouncing, the PRESSURE HOSE will not vent fast enough and
the COMPRESSOR is switched on again. The COMPRESSOR cannot run because there is still air pressure in the
system. This causes the COMPRESSOR to draw too much current and the FUSE will blow. If this happens, replace
the MANOMETRIC SWITCH, S28, Part No. 9186676, not the COMPRESSOR.
New MAGAZINE OPENER SOLENOID for the
The MAGAZINE OPENER SOLENOID 9180906 is no longer available. Use SOLENOID 9180907. The new
SOLENOID has improved wire, but the COIL is larger in diameter than the old COIL. When installing a new
SOLENOID, use only the SCREWS provided. If you use the old SCREWS, which are longer on a new SOLENOID,
the SCREWS might cause a short
New
Kodak
EC-L FILMS
•circuit against the COIL.
Kodak
MULTILOADER 700
Kodak MULTILOADER 700..................EC-L FILMS cannot be used in the MULTILOADER 700
Kodak MULTILOADER 700 PLUS.......EC-L FILMS
might not be detected in the MAGAZINE. The display
might indicate the MAGAZINE is empty but the last
film is inside. Additionally, check that the
FILM PRESENCE DETECTORS are adjusted to the
procedure in the Service Manual.
Kodak X-Omat MULTILOADER 300.....EC-L FILMS
700 PLUS, the last film might not be detected in the
MAGAZINE and it will stay there.
can be used. It is possible that the last film
can be used. As with the MULTILOADER
-2-
New VACUUM PUMPS for the
Kodak
MULTILOADER 700 and
MULTILOADER 700 PLUS
Starting with serial number 3292, 50 Hz and serial number 7211, 60 Hz new VACUUM PUMPS are being installed.
The new VACUUM PUMPS have improved DIAPHRAGMS. The new VACUUM PUMPS and REPAIR KIT
should be used in both the MULTILOADER 700 and the MULTILOADER 700 PLUS.
Description Part No.
VACUUM PUMP, 50 Hz 9285501
VACUUM PUMP, 60 Hz 9285601
REPAIR KIT for the VACUUM PUMP 9285706
Improved POWER SUPPLY for the
Kodak
MULTILOADER 700 and
MULTILOADER 700 PLUS
An improved POWER SUPPLY is used in the MULTILOADER 700 PLUS. This SUPPLY is also used as a
replacement part for the MULTILOADER 700. When you install a new style POWER SUPPLY:
• Only use the SCREWS provided to mount the new POWER SUPPLY. The SCREWS are a different size.
• Do not connect the POWER FAIL DETECT (PDF) wire to the new SUPPLY.
• Some of the DC TERMINAL labels are different. The new SUPPLY has one TERMINAL for V1+ and one for
V1-. Connect the V1 wires to the appropriate LUG. All of the other connections are the same.
Kodak
If you experience plus density artifacts on MIN-R 2000 films that are at the trailing edge of the film and are about
20 cm (8 in.) apart, check the O-RINGS on the FILM POCKET GUIDES. If they are black rubber O-RINGS, replace
them with foam ROLLERS. The foam ROLLERS are already on the bottom GUIDE. Replace all of the top ORINGS with the foam ROLLERS, Part No. 9184396.
MIN-R 2000 Film, Plus Density Artifacts
-3-
New A0 BOARD for the
Kodak
MULTILOADER 700 and
MULTILOADER 700 PLUS
Important
When you install a new PRINTED CIRCUIT BOARD A0, Part No. 9189070, see the figure below to set the
JUMPER A0X11.
JUMPER SETTING
A0x11
ML 700 PlusML 700
Op. Software
U33
Op. Software
U34
A0x11
Language
Eprom U35
U36
U37
H070_0191HC
PCB A0 PN 9189070
The MULTILOADER 700, A15 BOARD which was part of Mod 24, Publication No. MA3053-24, 7/96, is no longer
necessary. Insert the LANGUAGE EPROM U35 directly into the SOCKET U35.
The MULTILOADER 700 PLUS, A15 BOARD which was used up to serial number 3372, 50 Hz and serial number
7273, 60 Hz is no longer necessary. Insert the LANGUAGE EPROM U35 directly into the SOCKET U35.
-4-
Dave Guild, Service Engineer, Rochester
For More Information Contact:
U.S. Distributors Contact: GCSS Personnel Contact:
Health Imaging Film Handling TAC
Film Handling TAC
1-800-822-1414
U.S.: 1-800-822-1414
Canada: 1-800-433-1414
-5-
Kodak,X-Omat
, and
7C8750
Min-R
are trademarks.
sb3053_03feb98_277.doc
Printed in USA
EASTMAN KODAK COMPANY
HEALTH IMAGING
● ROCHESTER, N.Y. 14650
Loading...