Before using the KODAK mc3 Portable Multimedia Device, you need to:
m Attach the wrist strap.
m Load the batteries.
m Insert a KODAK Picture Card.
Attaching the Wrist Strap
Attach the wrist strap to carry the mc3 device.
1 Thread the short loop of the wrist strap
through the recessed post.
2 Thread the long end of the wrist strap
through the short loop. Pull until secure.
1
1
Loading the Batteries
Three AAA-size batteries are included with the mc3 device, so you can get
started immediately.
1 Slide the battery door, located on the
bottom of the device, so it flips open.
2 Insert the batteries as indicated inside the
battery compartment.
The single battery is inserted (+) end first;
the two other batteries are inserted (-) end
first.
3 Press down on the battery door. Slide it
until it locks in place.
NOTE: Because digital devices are demanding on batteries, keep an
extra set of batteries handy.
Consider purchasing a KODAK Ni-MH/Ni-Cd Battery Charger with
KODAK Ni-MH Rechargeable Batteries, available as an accessory
through a dealer of KODAK products or from our Web site at
http://www.kodak.com/go/accessories.
For guidelines on safe battery usage, see “Using Batteries Safely” on page 76.
2
Inserting a Picture Card
The mc3 device comes with a KODAK Picture Card, which stores your pictures,
videos, and music. The Picture Card (also known as a CompactFlash or
memory card) is removable, reusable, and x-ray safe.
Important: Use only certified Picture Cards that carry the
CompactFlash logo. KODAK Picture Cards are available as an
accessory through a dealer of KODAK products, or from our Web
site at http://www.kodak.com/go/accessories.
1 After ensuring that the mc3 device power is off,
open the Picture Card door.
Lip
2 Hold the Picture Card by the end that has a
raised lip that you can feel with your fingers.
This lip should face the back of the device.
The opposite end of the Picture Card (with tiny
holes) should face into the card slot.
CAUTION: The Picture Card can only be
inserted one way; forcing it may damage the
card or mc3 device.
3 Slide the Picture Card into the card slot.
When it is flush with the side of the device,
push it firmly.
The eject button (above the Picture Card)
pops out.
4 Flip the eject button down. Close the
Picture Card door.
1
3
Removing a Picture Card
1 Open the Picture Card door.
2 Flip the eject button up, then firmly press it
with your fingertip.
The Picture Card partially slides out.
3 With your fingernail under the lip, pull the
Picture Card from the card slot. Then close
the door.
Important: Do not eject a Picture Card while the video recording time
remaining is blinking on the LCD; you could lose your
video.
4
Turning the mc3 Device On and Off
After you have inserted the batteries and a Picture Card, turn the device on.
1 Press the Power button.
The Power Indicator LED lights up.
The LCD displays an image or other
information.
2 To turn the mc3 device off, press the Power
button again.
The device completes any tasks it is
performing before it shuts off.
Po w e r
Button
Po w e r
Indicator
1
5
Low Battery Icon
When battery power is low, a battery icon is displayed on the LCD. If no battery
icon is displayed, your batteries have enough power to run the mc3 device.
IndicatorMeaning
No icon is displayed on the
LCD
OK - Batteries are charged and ready for use.
Low - Batteries may need to be replaced or
recharged soon, but there is sufficient power
to use the device.
Power LED is flashingExhausted - Batteries are too weak to power
the device. The device will not operate until
you replace or recharge the batteries.
Sleep Mode
If the mc3 device senses no activity for an extended time, it enters “Sleep”
mode to conserve battery power. To awaken the device from Sleep mode, press
the Shutter button halfway down.
If the device is allowed to remain in Sleep mode, it will eventually turn off.
Press the Power button to turn the device back on.
6
Customizing the mc3 Device
Using the Settings submenu, you can:
m Choose sound preferences
m Set date and time
m Set video out
Find information on mode-specific settings in these chapters:
To Adjust Settings
Specific To
m Choose a language
m Format a Picture Card
m View information about the mc3 device
Such AsSee Chapter
m Equalizer
m Repeat
m Shuffle
m Video quality (Good and
Best settings)
“Playing Internet
Music” on page 15
“Taking Videos” on
page 21
1
m Self-Timer“Taking Pictures” on
page 27
NOTE: If you remove the batteries from the device for an extended
period of time, or if the batteries become exhausted, you may need to
reapply a setting.
7
Setting the Sound Preferences
You can set the mc3 device to these sound preferences:
Selected OnConfirmation sounds are played when:
m A picture is taken
m A video is started and stopped
All Onm All the above, and
m When any valid button is pressed (except the Power button)
All OffNo sounds
To change the sound setting:
1 The Mode selector may be in any position. Press the
Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the Sound icon,
then press the Select button.
The Sound settings are displayed.
4 Press the buttons to highlight the desired
setting. Press the Select button to save the setting.
8
Setting the Date and Time
The mc3 device displays the date and time in a 24-hour format. To set or adjust
the date and time:
1 The Mode selector may be in any position. Press the
Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the Date and Time
icon, then press the Select button.
The date and time settings are displayed.
4 Press the buttons to adjust the year, then press
the
button.
5 Repeat Step 4 for the month, day, and time.
6 When finished, press the Select button to save the
setting.
1
9
Setting Video Out
If you want to display pictures and videos on a television or video monitor
(using an optional KODAK AV Cable), the Video Out feature needs to be
correctly set.
The mc3 device is compatible with NTSC or PAL video signals. The NTSC format
is used in most countries, including the United States. PAL is generally used in
European countries.
1 The Mode selector may be in any position. Press the
Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the
Video Out icon, then press the Select button.
The Video out settings are displayed.
4 Press the buttons to highlight the desired
setting. Press the Select button to save the setting.
Accessories are available through a dealer of KODAK products or from our
Web site at http://www.kodak.com/go/accessories.
10
Setting the Language
To change the language setting:
1 The Mode selector may be in any position. Press the
Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the Language
icon, then press the Select button.
The Language settings are displayed.
4 Press the buttons to highlight the desired
setting. Press the Select button to save the setting.
The Settings submenu is displayed.
1
11
Formatting a Picture Card
If you have a Picture Card that has been used in another digital device, the card
may not be properly formatted for the mc3 device.
Important: The Format Picture Card function erases the contents
of the Picture Card and prepares the card for use in
the device.
1 Ensure that a Picture Card is in the device. The Mode
selector may be in any position. Press the Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the Format
Picture Card icon, then press the Select button.
The Format Picture Card menu is displayed.
4 Highlight Continue Format, then press the Select button.
The Formatting Card screen is displayed until the
Picture Card is formatted.
12
About the mc3 Device
You can view information about your mc3 device, including:
m Current firmware version
m Total number of pictures taken
m Total number of video clips taken
1 The Mode selector may be in any position. Press the
Menu button.
The settings for that mode are displayed.
2 Press the buttons to highlight the Settings
submenu. Then press the Select button.
3 Press the buttons to highlight the About icon,
then press the Select button.
The About screen is displayed.
4 When finished, press the Menu button.
A screen similar to this is displayed.
1
13
2Playing Internet Music
Your KODAK mc3 Portable Multimedia Device is a full-featured MP3 player!
With the mc3 device and its powerful software you can:
m Extract MP3 files from a music CD that you already own, or download
music from the Internet.
m Create, edit, and delete playlists.
m Play music through headphones or through a computer.
m Play music through a home, portable, or car stereo using an optional
stereo cable or cassette adapter.
Accessories are available through a dealer of KODAK products or from our
Web site at http://www.kodak.com/go/accessories.
For important MP3 information, See “Disclaimer” on page 73.
2
15
Obtaining MP3 Music Files
After you have loaded the software that is included with the mc3 device (see
“Installing the Software” on page 39), you can transfer MP3 music to the
device using any of these methods:
PlatformMethodDetails
WINDOWSWINDOWS
Explorer
RealJukebox
Software
A device such as
a card reader
MACINTOSH “Copy To”
method
A device such as
a card reader
Use standard WINDOWS functionality. See
“Using the WINDOWS Open Browser” on
page 51.
See “Installing Software for the KODAK
mc3” on page 42
See “Using a Picture Card Reader” on
page 50
Choose MC3 > Copy To MC3
See “Using a Picture Card Reader” on
page 54
16
Playing Music
To play an MP3 music file from a Picture Card, slide the Mode selector to the
Music position.
ToAct ion
Scroll through
songs
Scan information
on songs
Play or pause Press the button
U
N
E
M
T
C
E
L
E
S
StopPress the button.
Restar t the curre nt
song or to skip to
the next
Fast forward or
rewind a song
Vol u me
Controls
Headphone
Jack
Adjust the volume Press the (+) or (-)
Listen privatelyPlug in headphones.
NOTE: Use your computer software to edit the order of a playlist.
To connect the mc3 device to a computer, television, or stereo, see
“Connecting to a Computer, Television, or Stereo” on page 48.
Press one of the
buttons.
/
Press and hold one of
the buttons.
/
Press and release one of
the buttons.
/
Press and hold one of
the buttons.
/
buttons.
2
17
Adjusting Playback Options
You can adjust music settings to your preferences.
IconDescription
Equalizer
Adjusts low-, mid-, and high-range frequencies to give
best playback for these types of music:
m Pop
m Rock
m Jazz
m Classical
m Voice
Repeat
Repeats entire playlist until the Stop button is pressed, or
until the Mode selector is changed to another mode.
Shuffle
Plays MP3 files within a playlist in random order.
18
To change the music settings:
/
1 Slide the Mode selector to the Music icon.
2 Press the Menu button.
3 Press the buttons to highlight the Equalizer,
Repeat, or Shuffle setting, then press the Select button.
4 Press the buttons to adjust the setting, then
press Select to apply the new setting.
2
19
3Taking Videos
Use your KODAK mc3 Portable Multimedia Device to take and share videos
with sound. Just switch the device to the Video setting and get ready to take
great videos!
You can:
m Use the color LCD as a live viewfinder.
m Use the QuickView feature to review a video you just took, then choose
to keep or delete it.
m Adjust the video quality setting for desired results.
m Attach a tripod.
You can take approximately:
Seconds of VideoPerUsing This Setting
41 MB of Picture
20Good
Card storage
Best
(ideal for e-mail)
3
21
Loading...
+ 61 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.