Kodak C750 User Manual
Consumer Imaging
EASTMAN KODAK COMP ANY
Rochester, NY 14650
Kodak
C750 Zoom
Camera
CAMERA IDENTIFICA TION
3
2
1
10
1 Shutter button
2 Zoom dial
3 Format-selector switch
4 Lens cover/flash
4
5 Light sensor
6 Viewfinder
7 Auto-focus sensors
8 Lens
9 Red-eye-reduction/
self-timer lamp
10 Film-door lever
5
6
7
8
Unfold the front and back flaps of this manual to view the camera’s parts.
© Eastman Kodak Company, 2000
Pt. No. 919 5504
Printed in U.S.A.
ENGLISH/ESP AÑOL/FRANÇAIS
9
Unfold the front and back flaps of this manual to view the camera’s parts.
Camera Identification LCD Panel
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Y our model camera has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
provide reasonable protection against interference in residential use. The camera
generates, uses and can radiate radio frequency energy and, if not used in
accordance with the instructions, may cause interference to radio
communications. There is no guarantee that interference will not occur. If this
camera does cause interference to radio or television reception, which can be
determined by turning the camera off and on, you may reduce the interference by
the following:
— Reorient or relocate the receiving antenna.
— Increase the separation between the camera and the receiver.
— Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
40
39
38
37
23
22
21
20
19
18
11
12
13
17
14
11 Battery door
12 Viewfinder eyepiece
13 Flash/camera-
ready lamp
14 LCD panel
15 Flash-mode button
16 Mode button
17 Strap post
18 Film door
19 Tripod socket
15
20 Mid-roll-change
(MRC) button
21 Enter/self-timer
16
button
22 Select button
23 Menu button
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations
25
24
AUTO FILL
PRINT
TITLEROLL
36
26 27
PM
ISO
QTY
333435
28
29
30
31
32
24 Auto-flash indicator
25 Red-eye-reduction
indicator
26 Fill-flash indicator
27 Flash-off indicator
28 Mode-selector arrow
29 PM indicator
30 ISO film-
speed display
31 Title/print-quantity
display
32 Self-timer indicator
33 Spot-focus icon
34 Nightview icon
35 Portrait icon
36 Infinity-focus icon
37 Frame counter
38 Film-presence
indicator
39 Date/time display
40 Battery symbol
KODAK ADVANTIX
C750 Zoom Camera
Welcome to the world of the Advanced Photo System!
And thank you for buying this KODAK ADVANTIX Camera.
NEED HELP WITH YOUR CAMERA?
Go to our Web site at http://www.kodak.com (for US) or
http://www.kodak.ca (for Canada) or call:
Kodak (USA only) from 9:00 a.m. to 7:00 p.m. (Eastern time) Monday through
Friday at 1 (800) 242-2424.
Kodak (Canada only) from 8:00 a.m. to 5:00 p.m. (Eastern time) Monday
through Friday at 1 (800) 465-6325, ext. 36100; for the Toronto area,
call (416) 766-8233, ext. 36100.
When you call, please have your camera available.
For warranty purposes, please keep your sales receipt as proof
of the date of purchase.
© Eastman Kodak Company, 2000
ENGLISH
1
CONTENTS
ADVANCED PHOTO SYSTEM
FEATURES AVAILABLE WITH
THIS CAMERA ......................................3
GETTING STARTED ................................. 5
Loading the battery .............................. 5
Setting the language ............................ 6
List of languages .................................. 7
Date and time imprinting ....................... 8
Setting the date and time ..................... 8
ATTACHING THE STRAP .........................9
CONTROL-BUTTON ACTUATOR .......... 10
LOW-BATTERY INDICATOR .................. 1 0
BATTERY TIPS ...................................... 1 0
POWER SHUT-OFF................................ 11
LOADING THE FILM .............................. 11
TAKING PICTURES ............................... 1 3
Typical print sizes (formats)................ 14
Using the focus lock ........................... 1 5
Tips for better pictures ....................... 1 5
USING THE ZOOM LENS ...................... 1 6
TAKING FLASH PICTURES .................. 1 7
Flash-to-subject distance ................... 18
Flash/warning-lamp signals ............... 1 8
2
FLASH MODES ..................................... 1 9
Auto flash with
red-eye reduction ........................... 19
Fill flash............................................... 19
Flash off ............................................. 1 9
Auto flash without
red-eye reduction ........................... 20
Selecting the flash modes ................. 2 0
SPECIAL-OPTION MODES ................... 20
Infinity-focus mode ............................. 2 1
Portrait mode ...................................... 21
Nightview mode .................................. 2 1
Center-spot focus mode .................... 21
Selecting the special-option modes .. 2 1
USING THE SELF-TIMER ...................... 2 3
TITLE IMPRINTING ................................ 2 4
TITLE-SELECT LIST .............................. 2 4
PRINT-QUANTITY SELECTION (PQS).. 2 6
ISO FILM-SPEED DISPLAY .................. 26
UNLOADING THE FILM ......................... 27
Automatic rewind ................................ 27
Mid-roll change (MRC)........................ 2 7
CARING FOR YOUR CAMERA .............. 28
TROUBLESHOOTING............................ 29
SPECIFICATIONS .................................. 31
ADV ANCED PHOTO SYSTEM FEA TURES
AV AILABLE WITH THIS CAMERA
Triple format selection
• You can take three different size
pictures: Classic (C), Group/HDTV (H),
and Panoramic (P) pictures from the
same film cassette.
the viewfinder changes to match each
format selection.
The masking inside
Date and time/title imprinting
• The date, time, and cassette ID
number are printed on the back of your
prints, which makes it easy to organize
pictures and order reprints. You can
choose from one of 41 preprogrammed titles (12 languages
available) to print on the back of the
prints.
See your photofinisher for a full
description of available services.
Double exposure protection (DEP)
• Don’t worry about accidentally reexposing your film. Your camera reads
the Film Status Indicator (FSI) on the
film cassette to prevent double
exposures.
Flip flash plus
• This system automatically adjusts
to provide just the right light in
any situation. The flash system:
–
provides extra
with the extension of the flip flash and
the red-eye-reduction mode,
–
automatically turns on for
lit scenes
–
delivers brighter light for clearer,
more colorful pictures for
distance shots
–
provides softer light for more natural
images for
–
automatically
more sparkle and clarity in harshly
lit
–
recharges quickly so it is
ready to capture those
peak moments
portraits
red-eye reduction
,
,
close-ups
, and
,
provides fill-in light for
spontaneous
.
dimly
3
Picture quality information
exchange (PQix)
• This camera records vital scene data
on the film’s magnetic information
strip and communicates that
information to the photo lab to
optimize lighting and color for betterlooking prints.
Mid-roll change (MRC)
• You can remove your film in mid-roll
and later reload it and continue taking
pictures. MRC lets you:
–
switch film speeds in mid-roll to
match scene requirements,
–
organize by dedicating individual
film rolls to specific subjects, and
–
share a family camera in which the
members use their own roll of film.
4
Easy, drop-in loading
• Easy, drop-in loading is fast and
virtually error-free, eliminating blank
rolls and double exposures. The
camera uses KODAK ADVANTIX Film.
The film cassette, unlike the traditional
35 mm cartridge, communicates the
status of film and becomes the carrier
and storage container for the
processed film.
Film status indicator (FSI)
• A highlighted indicator advances from
one symbol to another to identify the
status of the film inside the cassette.
Unexposed
1
2
Partially
4
3
Processed Negatives
Exposed
Fully
Exposed
GETTING ST ARTED
Before you take pictures, you need to
load the battery, set the language, and
set the date and time.
Loading the battery
This camera uses one 3-volt lithium
KODAK KCR2 (or equivalent) Battery
that supplies power for all camera
operations.
1. Slide the battery-door latch and lift to
open the battery door (11).
2. Insert the battery into the
battery chamber.
3. Snap the battery door closed.
• After you load a new battery into the
camera, reset the date and time.
5
Setting the language
US English is initially set into the memory
of this camera, but you can select
another language (12 options available).
See the table on page 7 for the List of
languages and the LCD (Liquid Crystal
Display) abbreviated codes.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8) and to
turn on the camera.
6
2. Press and hold the menu button (23)
for approximately 4 seconds until
US appears on the LCD panel (14).
MENU
SELECT
ENTER
• When you release the button, the
language code “blinks.”
3. Press the right or left side of the zoom
dial (2) or the select button (22)
to cycle to your selection.
C
H
P
4. Press the enter/self-timer button (21)
to complete your selection.
MENU
SELECT
ENTER
List of languages
Languages LCD display
American English US
UK English En
German dEU
French FrA
Spanish ESP
Japanese JP
Danish dEn
Finnish FI
Italian I
Norwegian n o r
Portuguese P
Swedish S
g
7
Date and time imprinting
Traditional cameras print date and/or
time information directly onto the film.
Your camera uses the film’s magnetic
data-recording capability to record date
and time information, which your
photofinisher can imprint only on the
back of your photographs. This camera
has a quartz clock and automatic
calendar through the year 2099.
Setting the date and time
Choose from three formats:
(month/day/year, day/month/year, or
year/month/day) and time format
(hour/minute) with PM display.
1. Repeatedly press the menu
button (23) to scroll and select the
desired function.
2. Press the select button (22).
MENU
• The first number(s) in the date- or
time-option mode will “blink.”
3. Press the zoom dial (2) or select
button (22) to change the number(s).
• Press the right side of the zoom dial
to increase the number and the left
side to decrease the number.
SELECT
ENTER
MENU
8
SELECT
ENTER
4. Press the enter/self-timer button (21)
to store the selected number(s) and to
activate the next “blinking” number(s).
MENU
5. Follow steps 3 and 4 to continue your
selection or press the enter/self-timer
button again to stop the number(s)
from blinking and to end your
selection.
SELECT
ENTER
ATT ACHING THE STRAP
1. Insert the shorter looped end of the
strap behind the strap post (17).
2. Thread the longer end of the strap
through the shorter loop.
3. Pull the strap tight.
9
CONTROL-BUTTON ACTUATOR
You can use the knob on the clasp of the
camera strap to actuate the small control
buttons on the camera.
LOW-BA TTERY INDICA TOR
It’s time to replace the battery when—
• the battery symbol (40) “blinks” on the
LCD panel (14),
• none of the indicators, except for a
steady battery symbol, appear on the
LCD panel and the shutter button (1)
cannot be operated,
• the LCD panel is blank when the lens
cover/flash (4) is up.
10
or
BA TTERY TIPS
• Dispose of batteries according to
local and national regulations.
• Keep a spare battery with you at
all times.
• Read and follow all warnings and
instructions supplied by the battery
manufacturer.
• Keep batteries away from children.
• Do not try to take apart, recharge or
short circuit the battery, or subject it to
high temperature or fire.
• Store batteries in their original
packaging prior to use.
• Do not use rechargable batteries.
• Remove the battery from the camera
when the camera is not going to be
used for an extended length of time.
• In the unlikely event that battery fluid
leaks onto your skin, contact Kodak
Health, Safety and Environment
Information at 1-716-722-5151 in
the U.S.
• In the unlikely event that battery fluid
leaks inside the camera, U.S.
customers can contact the Kodak
Information Center (KIC) at 1-800-242-
2424. Customers outside the U.S. can
contact their local Kodak Customer
Service representative.
POWER SHUT-OFF
To save battery power, the camera automatically goes into a sleep mode if it is
not operated for more than 2 1/2 minutes.
You can press almost any of the control
buttons, except for the format-selector
switch (3), to awaken the camera. When
the camera is not used for an extended
time, close the lens cover/flash to
completely turn off the camera.
LOADING THE FILM
You can load film into the camera with the
lens cover/flash opened or closed.
1. Rotate the film-door lever (10) to open
the film door (18).
O
N
P
E
• The film door opens only when the
film chamber is empty or the film in
the camera is completely rewound
into the film cassette and the motor
stops running.
11
2. Insert the film cassette completely
into the film chamber. Make sure the
Film Status Indicator (FSI) on the film
cassette is at ● (#1 position) for a
new cassette or at ◗ (#2 position) for
a partially exposed cassette.
3
4
2
1
Look for this logo to be certain that the film you buy is
made for this camera.
Look for this logo to select a certified photofinisher for
developing your film and to assure that you get all the
features of the Advanced Photo System.
12
• Do not force the film cassette
into the film chamber.
3. Close the film door to start the auto-
film advance. The frame counter (37)
on the LCD panel (14) shows the
number of pictures remaining on the
film cassette.
TAKING PICTURES
Y ou can take Classic (C),
and Panoramic (P) pictures on the same
film cassette. See the table on page 14
for Typical print sizes (formats). Your
photo-processing cost may be based on
the format size(s) that you use to
expose the film.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
Group/HDTV (H)*
2. Slide the format-selector switch (3) to
select C, H, or P format. The
,
viewfinder changes to show the
selected field of view.
C
CH
H
P
P
* High Definition Television (HDTV) prints are the
same aspect ratio as the TV for CD interface
capabilities.
C
H
P
3. Look through the viewfinder
eyepiece (12) placing the Auto Focus
(AF) brackets on the subject. For a
sharp picture, stand at least 2 ft
(0.6 m) from your subject.
13
4. Partially press down the shutter
button (1) until the flash/camera-ready
lamp (13) turns green. Fully press
down the shutter button to take
the picture.
C
H
P
T ypical print sizes (formats)
CHP
Classic Group (HDTV) Panoramic
3.5 x 5 in. or 4 x 6 in. 3.5 x 6 or 4 x 7 in. 3.5 x 8.5 in. to 4 x 11.5 in.
(88.9 x 127 mm or (88.9 x 152 mm or (88.9 x 216 mm to
102 x 152 mm) 102 x 178 mm) 102 x 292.7 mm)
NOTE: Your photofinisher generally provides 4 x 6, 4 x 7, and 4 x 11.5 in. (102 x 152, 102 x 178, and
102 x 292.7 mm) sizes. Some local printers may offer 3.5 x 5, 3.5 x 6, and 3.5 x 8.5 in.
(88.9 x 127, 88.9 x 152, and 88.9 x 216 mm) sizes.
14
Using the focus lock
This camera automatically focuses on
whatever is within the Auto Focus (AF)
brackets of the viewfinder eyepiece. To
get a sharp picture, make sure the AF
brackets are on your main subject. If you
want to take a picture with the subject
positioned outside the AF brackets, use
the focus lock as follows:
1. Place the AF circle on the subject that
you want focused in the picture.
AF Circle
Viewfinder
2. Partially depress and hold the shutter
button (1) to lock the focus position
and wait for the flash/camera-ready
lamp (13) to turn green.
3. While still partially depressing the
shutter button, move the camera until
your subject is where you want
it within the viewfinder eyepiece (12).
Viewfinder
4. Fully press down the shutter button to
take the picture.
Tips for better pictures
• Move close enough to your subject so
it fills the viewfinder but not closer
than 2 ft (0.6 m).
• Take pictures at the subject’s level.
Kneel down to take pictures of
children and pets.
• Hold your camera vertically to capture
tall, narrow subjects, such as
a waterfall, skyscraper, or a single
person.
15
• Add interest to your picture by framing
it with a tree branch, a window, or
even the rails of a fence.
• Keep the sun behind you. This provides
the best subject illumination.
• Stand at an angle to shiny surfaces
like windows or mirrors to avoid flash
reflection and bright spots in your
pictures.
• Turn on all room lights and have your
subject look at the red-eye-reduction
lamp to reduce red eyes in flash
pictures.
USING THE ZOOM LENS
This camera has a motorized-zoom lens
that lets you select the ideal lens-focal
length for taking pictures. When you turn
on the camera, it is initially set to the
wide-angle position.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
16
2. Look through the viewfinder
eyepiece (12).
3. Press the right side of the zoom
dial (2) to zoom
closer
to the subject
in the telephoto mode or the left side
to zoom
away
from the subject in the
wide-angle mode.
C
H
P
4. Press the shutter button (1) to take
the picture.
• The lens barrel automatically
returns to the wide-angle position
after 2 1/2 minutes.
TAKING FLASH PICTURES
In dim light, such as indoors or outdoors
in heavy shade, or on dark overcast
days, you need flash. Your camera
features an automatic flash that fires
when you need it. The special flip-flash
plus system of this camera shortens the
flash duration in close-up pictures. This
enhances your flash pictures and helps
to conserve the battery life.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
2. Keep the subject within the
recommended distance range for the
speed of film in your camera.
Do not take pictures beyond the
maximum distance or your pictures
will be dark.
3. Partially press down the shutter
button (1).
4. When the flash/camera-ready
lamp (13) glows green, fully press
down the shutter button to take the
picture (see Flash/warning-
lamp signals on page 18).
17
Flash-to-subject distance
ISO Film Wide Tele
Speed (24 mm) (60 mm)
50 2 to 10 ft 2 to 7 ft
(0.6 to 3.0 m) (0.6 to 2.1 m)
100 2 to 14 ft 2 to 10 ft
(0.6 to 4.3 m) (0.6 to 3.0 m)
200 2 to 20 ft 2 to 14 ft
(0.6 to 6.1 m) (0.6 to 4.3 m)
400 2 to 29 ft 2 to 20 ft
(0.6 to 8.8 m) (0.6 to 6.1 m)
800 2 to 41 ft 2 to 28 ft
(0.6 to 12.5 m) (0.6 to 8.5 m)
1600 2 t o 57 ft 2 t o 39 ft
(0.6 to 17.4 m) (0.6 to 11.9 m)
18
Flash/warning-lamp signals
Lamp Indicator Situation
Glows green • Camera ready for
picture-taking
Glows red • Subject between
8 in. (20 cm) and
2 ft (0.6 m) from
camera. Shutter
button locks.
“Blinks” red • Flash not
fully charged
• Camera movement
• Beyond the
flash range
FLASH MODES
Besides the auto-flash mode with redeye reduction (initial default setting of
the camera), you can select fill flash,
flash off, or auto-flash without red-eye
reduction. Choose the flash mode that
best suits your subject and
surroundings.
Repeatedly press the flash-mode
button (15) to view the choices on
the LCD panel (14) and to make
your selection.
EXP
LEFT
AUTO
MENU
FILL
SELECT
MODE
ENTER
Auto flash with
red-eye reduction
AUTO
Some people’s eyes (and some pets’)
can reflect flash with a red glow. The
extended flash and the red-eyereduction lamp on the camera help to
minimize red eyes in flash pictures.
Fill flash
FILL
When bright light indoors or outdoors
comes from behind the subject
(backlighting), dark shadows
(especially on faces) may occur. Use
fill flash to lighten these shadows.
Flash off
When you do not want to use the flash,
especially indoors where flash is
prohibited, or to capture the ambiance
of existing light, use the flash-off
feature. Use a tripod or place the
camera on another firm support, and
use high-speed film because the
shutter speed in these situations will
most likely be slow.
19
Auto flash without
red-eye reduction
Use this feature to take pictures of
subjects other than people.
AUTO
Selecting the flash modes
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
2. Repeatedly press the flash-mode
button (15) until the mode-selector
arrow (28) points to the fill-flash
indicator (26), flash-off indicator (27),
auto-flash indicator (24) without redeye reduction, or auto-flash
indicator (24) and red-eye-reduction
indicator (25).
3. Frame your subject within the
viewfinder eyepiece (12).
20
4. Partially press down the shutter
button (1). When the flash/camera-
ready lamp (13) glows green, fully
press down the shutter button to take
the picture.
The fill-flash and flash-off modes
cancel when you turn off the camera,
select a different flash mode, or when
the camera powers down. The autoflash modes remain selected in these
instances.
SPECIAL-OPTION MODES
The special-option modes let you
tailor the camera’s fully automatic
operation to provide optimal camera
settings for infinity-focus, portrait,
nightview, or center-spot focus.
Repeatedly press the mode
button (16) to scroll through
the selections.
AUTO
EXP
LEFT
MENU
Infinity-focus mode
Use this mode, to capture sharp,
distant scenery when you take
pictures outdoors during the day or
through windows.
FILL
SELECT
MODE
ENTER
Portrait mode
Use this mode, to automatically zoom to
provide suitable framing for portraits.
Nightview mode
Use this mode, to balance the flash and
existing light exposure so that you can
take beautiful pictures of people at
sunset or at night. Use a tripod (tripod
socket [19]) or place the camera on
another firm support, and use highspeed KODAK ADVANTIX Film because
the shutter speed at night will most likely
be slow.
Center-spot focus mode
Use this mode, for extremely precise
focus control of what you consider the
most important parts of your subject.
21
Selecting the special-option modes
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
2. Repeatedly press the mode button (16)
until the infinity-focus icon (36), portrait
icon (35), night-view icon (34), or
spot-focus icon (33) appears on the
LCD panel (14).
• In the infinity-focus mode, the
camera is automatically set for
flash off.
• In the night-view mode, all flash
options, except for flash off,
are available.
• In the portrait and spot-focus
modes, all flash options
are available.
3. Frame your picture in the viewfinder
eyepiece (12).
22
4.
Infinity-focus mode
mode
:
– Simply press the shutter button (1)
to take the picture.
Portrait mode
– Press the shutter button halfway
down until the zoom lens adjusts for
suitable framing.
– Press the shutter button completely
down to take the picture.
Center-spot focus mode
– Place the AF circle within the
viewfinder eyepiece (12) on
your subject.
– Press the shutter button completely
down to take the picture.
The special-option-mode selections
cancel when you turn off the camera,
select a different option mode, or when
the camera powers down. The portrait
mode automatically cancels after you
take the picture.
or
night-view
:
:
USING THE
SELF-TIMER
Use the self-timer feature when you want
to include yourself in pictures.
1. Attach a tripod to the camera tripod
socket (19) or place it on another
firm support.
2. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
3. Press the enter/self-timer button (21).
MENU
• The self-timer indicator (32) appears
on the LCD panel (14).
SELECT
ENTER
4. Look through the viewfinder
eyepiece (12) to compose the picture
and to allow room for yourself in it.
5. Press the shutter button (1).
6. Quickly position yourself in the
composed picture making sure that
you see the self-timer lamp (9).
• The self-timer lamp on the front of
the camera blinks for approximately
10 seconds before the picture
is taken.
• To cancel the self-timer selection
before the shutter releases, press
the enter/self-timer button again or
close the lens cover/flash.
• The self-timer automatically turns off
after the shutter releases.
23
TITLE IMPRINTING
Choose a print title from the TITLESELECT LIST and/or a roll title for the
entire roll of film. The titles are recorded
on the film’s magnetic data strip. At
certified Advanced Photo System labs,
the selected titles are
printed on the back of
your photograph.
1. Press the menu
button (23) until
“TITLE PRINT”
“
ROLL TITLE”
appears on the LCD panel (14).
EXP
LEFT
• The LCD panel displays
PRINT”
“
_ _
” (for title-selection code) with
the language designator.
24
or
FILL
AUTO
TITLE
PRINT
SELECT
MENU
or “
ENTER
ROLL TITLE” and
MODE
“TITLE
2. Press the select button (22).
• The title-selection codes
“00” blink on the LCD panel.
3. Press the right or left side of the zoom
dial (2) or the select button (22) to
select a title number. See the TITLE-
SELECT LIST on page 25 for the titlenumber selections.
4. Press the enter/self-timer
button (21) to store the information.
• The print-title or roll-title selection
continues through out the roll.
• To cancel the print title for
subsequent pictures or roll title for
the entire roll, follow steps 1
through 4, but for step 3, select Title
“
_ _
” (None) or a different title.
TITLE-SELECT LIST
The following table indicates the
title numbers for in-the-camerastored titles.
Title Title
Number
00 Christmas
01 Birthday
02 Vacation
03 Honeymoon
04 Wedding
05 Hanukkah
06 Graduation
07 Family
08 Party
09 Holiday
10 Anniversary
11 Friends
12 School Event
13 Trip
14 I Love You
15 Thank You
16 Season’s Greetings
17 Happy Birthday
18 Congratulations
19 Merry Christmas
20 Festival
Title Title
Number
21 First day of School
22 Tour
23 New Year’s
24 Easter
25 Happy New Year
26 Reunion
27 Father’s Day
28 Mother ’s Day
29 Memories
30 Baptism
31 Halloween
32 Happy Holiday
33 Independence Day
34 Thanksgiving
35 Rosh Hashanah
36 Yom Kippur
37 Memorial Day
38 Labor Day
39 Valentine’s Day
40 Canada Day
- - None
25
PRINT-QUANTITY SELECTION
Before you take a picture, choose the
number of prints, from 0 to 9, that you
want. This service is dependent
on the photofinisher’s capability.
1. Repeatedly press the menu
button (23) until
“P 1
” appears on the LCD panel (14).
EXP
LEFT
AUTO
MENU
“PRINT QTY”
FILL
PRINT
QTY
SELECT
ENTER
and
MODE
3. Press the enter/self-timer
button (21) to store the information.
• After you take the picture, the print
quantity defaults to 1.
Remember you must select a print
quantity before you take a picture.
ISO FILM-SPEED DISPLAY
View the ISO film speed of the film on the
LCD panel (14) when you first turn on
the camera. The LCD panel displays the
ISO speed for approximately 3 seconds
and then returns to the date display.
2. Press the right or left side of the zoom
dial (2) or the select button (22) to
select the number of prints
you want.
26
EXP
LEFT
AUTO
FILL
ISO
MODE
UNLOADING THE FILM
Automatic rewind
The camera automatically rewinds
the film into the cassette after the
last exposure.
1. Wait for the film to completely
rewind into the film cassette and
for the motor to stop running.
• When the motor stops running, the
frame counter (37) indicates “0” on
the LCD panel (14).
2. Rotate the film-door lever (10) to open
the film door (18).
3. Remove the
film cassette
from the
camera and
reload with
new KODAK
ADVANTIX
Film.
3
4
2
1
• The FSI on the fully-exposed film
cassette is at ✖ (#3 position) and the
frame counter indicates “E” on the
LCD panel.
Mid-roll change (MRC)
You can remove your film in mid-roll and
later reload it and continue picture-taking.
The Film Status Indicator (FSI) on a
partially exposed film cassette is set
to ◗ (#2 position). When you reload the
film cassette into the camera, the
camera automatically advances the film
to the first unexposed frame. Film can be
rewound and reloaded until the last
picture is taken. The camera automatically rewinds the film and sets the FSI
to ✖ (#3 position) when the last picture
is taken.
27
1. Gently press the mid-roll-change
button (20) with the control-button
activator on the camera strap to start
the auto-film rewind.
2. See Automatic rewind, steps 1-3.
• Either reinsert the partially exposed
film cassette into the camera to take
more pictures or take it to your
photo lab for processing.
28
CARING FOR YOUR CAMERA
• Protect the camera from dust,
moisture, sudden impact, and
excessive heat.
CAUTION: Do not use solvents or
harsh or abrasive cleaners on the
camera body.
• If the lens appears dirty, breathe on it
to form a mist and wipe the surface
gently with a soft, lintless cloth or
lens-cleaning tissue. Never wipe
a dry lens.
CAUTION: Use solvents or solutions
designed for cleaning camera lenses.
Do not use chemically treated tissues
intended for cleaning eye glasses.
• Remove the battery when you store
the camera for an extended time.
CAUTION: To prevent possible
damage and electrical shock, do not
attempt to disassemble or repair the
camera or flash unit by yourself.
Loading...