Page 1
{ServiceManual}{Produ ction}{KodakServiceSupp ort}{ExternalAndInterna l}
Kodak EasyShare C300 DIGITAL CAMERA
Kodak EasyShare C310 DIGITAL CAMERA
Kodak EasyShare CD40 DIGITAL CAMERA
SERVICE MANUAL
for the
Service Code: 8784
Service Code: 8594
Publication No. SM8784-1
31JAN06
Supersedes SM8784-1
27APR05
Service Code: 1387
Important
Qualified service personnel must repair this equipment.
Confidential
Restricted Information
© Eastman Kodak Company, 2006
Page 2
PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the
subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice, and
makes no warranty, express or implied, with respect to this information. Kodak sh all not be liable
for any loss or damage, including consequential or special damages, resulting from any use of
this information, even if loss or damage is caused by Kodak’s negligence or other fault.
This equipment includes parts and assemblies sensitive to damage from electrostatic
discharge. Use caution to prevent damage during all service procedures.
Table of Contents
Description Page
Illustrated Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Necessary Materials
Configurations for the CAMERA DOCK
Reference Table for New CAMERAS
Reference Table for Adjustment Procedures
Visual Index
Equipment Parts
COVERS
MONITOR LCD
MCU BOARD AND LENS AY
POWER BOARD AND FRAME AY and TAKE BOARD
Alphabetical Index
Diagnostics
Error Codes
E00
E20
Diagnostic Tests
Checking for Low Voltage
Checking for Uniform Flash
Checking the Power-On Self-Test
Checkout Procedures
Checking the General Functions of the CAMERA
Checking the ACTUATION, FLASH, and POWER-ON COUNTERS
Checking the External Components of the CAMERA
Adjustments
SHUTTER - Delay
CCD - White Balance
Replacements
Additional Service Procedures
Installing the
Making the MEMORY CARDS for Service
Downloading the Files from the Partner Site
Making the “C300_Self_Test” MEMORY CARD
Making the “C300_Shutter_Delay” MEMORY CARD
Making the “C300_AWB_ISO” MEMORY CARD
Upgrading the Firmware Using the MEMORY CARD
Upgrading the Firmware Using the Internal Memory
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Altek VISTA SERVICE SOFTWARE on the Computer. . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 31
2 31JAN06 – SM8784-1
Page 3
Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Block
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
System Overview
Schematic
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MCU BOARD
POWER BOARD
TAKE BOARD
Component Locator
MCU BOARD
POWER BOARD
TAKE BOARD
Publication History
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SM8784-1 – 31JAN06 3
Page 4
SERVICE MANUAL
Section 1: Illustrated Parts List
Necessary Materials
Primary Tools:
Description Tool or Part No.
ESD MAT Region Provided
SCREWDRIVER - Phillips, No. 004 x 0 m TL-5429
SCREWDRIVER - Phillips, No. 000 x 40 mm (1.57 in.) TL-5430
SCREWDRIVER - Phillips, No. 2 x 40 mm (1.57 in.) TL-5431
SCREWDRIVER - Phillips, No. 0 x 50 mm (1.96 in.) TL-5432
TWEEZERS - 2 TL-1207
SOLDERING IRON - 35 W, 188 - 204
STATION - weller soldering, 50 W, optional TL-5412
TIP - soldering iron, standard ST1, optional TL-5413
TIP - soldering iron, single flat ST5, optional TL-5414
TIP - soldering iron, conical ST7, optional TL-5415
SOLDER REMOVAL TOOL TL-3314
FLASH CAPACITOR DISCHARGE TOOL - resistor minimum, 6.8 kΩ TL-5337
DIGITAL VOLTMETER TL-4114
DC POWER SUPPLY - 0 - 12 V, 2.5 A with clip leads, ez or alligator Region Provided
IQ TEST CHART TL-5179
Loctite 495 SEALANT or similar material Region Provided
AIR HOSE - optional Region Provided
SCREWDRIVER - Milwaukee, cordless, with battery and charger, optional TL-5424
HEX ADAPTER - 0.40 mm (0.02 in.) bit, optional TL-5421
BATTERY for a POWER SCREWDRIVER - 2.4 V, optional TL-5422
BIT - power, 80 mm (3.14 in.), 4 mm (0.15 in.) drive, optional TL-5423
Kodak LENS CLEANING PAPER Region Provided
Kodak LENS CLEANER 1C8000
COVER CLEANER - Johnson SHINE-UP FURNITURE WAX TL-5182
COMPUTER
• IBM or IBM compatible with a Pentium PROCESSOR
• 233 MHz minimum
• Microsoft Windows 98, 98 SE, 2000, MILLENNIUM EDITION or XP PROFESSIONAL
OPERATING SYSTEM
• 64 MB RAM, 128 MB RAM is recommended
• 100 MB of space available on the HARD DISK
• CD-ROM DRIVE
• USB PORT
• Color MONITOR with a minimum resolution of 8 00 x 600 pixels, 16-bit high color,
24-bit true color is recommended
• Access to the INTERNET
°C (370 - 400°F) TL-2818
Region Provided
4 31JAN06 – SM8784-1
Page 5
Illustrated Parts List
Special Tools:
Tool, Part, or
Description
Catalog No.
BATTERY VOLTAGE ADJUSTMENT TOOL - battery simulator TL-5637
DIGITAL MULTIMETER TL-4114
USB INTERFACE CABLE for selected Kodak EasyShare PRODUCTS and DC SERIES
853 9249*
DIGITAL CAMERAS
CAMERA NEST TL-5846
Kodak EasyShare CAMERA DOCK 6000 821 0049
Kodak DOCK ADAPTER KIT D-22 *** 175 6824
Kodak CUSTOM DOCK INSERT 3F6285
Kodak EasyShare CAMERA DOCK SERIES 3 188 6597
Kodak OXY-ALKALINE DIGITAL CAMERA BATTERIES - 2 3E7101
Kodak Ni-MH BATTERY PACK 114 8683
Kodak EasyShare RAPID CHARGER for Ni-MH RECHARGEABLE BATTERY PACK 891 4012
Kodak SD/MMC MEMORY CARD *
Kodak MULTI-CARD READER 134 2682
Kodak EasyShare SOFTWARE - Version 4.0 or higher *
SERVICE SOFTWARE - “Vista for Service V4.1.0.3.zip” **
Firmware files - “script4service(C300).zip” **
* This item is provided by the region.
** This file is on the Kodak Partner Site.
*** See Configurations for the CAMERA DOCK
.
SM8784-1 – 31JAN06 5
Page 6
SERVICE MANUAL
Configurations for the CAMERA DOCK
CUSTOM
DOCK
INSERT
DOCK ADAPTER
KIT D-22
CAMERA
DOCK
6000
Figure 2
CUSTOM
DOCK
INSERT
CAMERA
DOCK
SERIES 3
P252_0075BAFigure 1
Note
• You must use the Kodak DOCK ADAPTER KIT D-22 when connecting the following to the Kodak EasyShare
CAMERA DOCK 6000.
– Kodak EasyShare C300 DIGITAL CAMERA
– Kodak EasyShare C310 DIGITAL CAMERA
– Kodak EasyShare CD40 DIGITAL CAMERA
• The above CAMERAS are also compatible with:
– Kodak EasyShare CAMERA DOCK SERIES 3
– other 26-PIN DOCKS
6 31JAN06 – SM8784-1
Page 7
Illustrated Parts List
Reference Table for New CAMERAS
Use the following catalog numbers to order a replace m en t CAM E RA if the CAME R A is under wa rr an ty an d cann o t
be repaired, or to order a MASTER CAMERA.
Catalog No.
Region Language
Americas - with CHECKPOINT TAG • English
• French
• Spanish
Americas - without CHECKPOINT TAG • English
• French
• Spanish
Brazil • Italian
• Portuguese
• Spanish
European, African and Middle Eastern
Region
Greater China/Taiwan • English
Peoples Republic of China • English
Asia Pacific/Korea • English
Japan Japanese 806 8843 178 3778 857 8205
Kodak Service & Support - class A, bulk English SP 147 2760 SP 137 8108 SP 885 1255
Kodak Service & Support - class A, retail English SP 127 1980 SP 890 9434 SP 860 6436
Kodak Service & Support - class B, bulk English SP 818 4020 SP 165 0548 SP 899 1648
Kodak Service & Support - class B, retail English SP 128 3605 SP 121 9120 SP 159 2609
• English
• French
• German
• Chinese
– simplified
– traditional
• Korean
• Chinese
– simplified
– traditional
• Korean
• Chinese
– simplified
– traditional
• Korean
for C300
127 1980 890 9434 860 6436
152 7621 193 7515 893 5199
145 4420 850 9382 860 9687
197 0912 124 2965 897 4529
155 0086 831 5178 141 2782
846 5601 885 6338 856 7158
837 6618 140 2502 888 9370
Catalog No.
for C310
Catalog No.
for CD40
Reference Table for Adjustment Procedures
After the installation of the following component, do these procedures:
Component Procedure
MCU BOARD AND LENS AY • “
SM8784-1 – 31JAN06 7
SHUTTER - Delay” on Page 24
• CCD - White Balance on Page 25
Page 8
SERVICE MANUAL
Visual Index
1
3
2
P238_6501ECA
P238_6501EC
1
4
Item Description
1 “
COVERS” on Page 9
2 “POWER BOARD AND FRAME AY and TAKE BOARD” on Page 13
3 “MCU BOARD AND LENS AY” on Page 12
4 “MONITOR LCD” on Page 11
8 31JAN06 – SM8784-1
Page 9
Equipment Parts
CautionCaution
• Dangerous Voltage
• You must discharge the STROBE CAPACITOR after removing the COVERS.
Figure 1 COVERS
4
4
7
7
2
2
Illustrated Parts List
6
6
5
5
P238_6500DCA
P238_6500DC
9
9
8
8
3
3
1
1
1
1
SM8784-1 – 31JAN06 9
Page 10
SERVICE MANUAL
Figure 1 COVERS
Item Part No. Description Quantity Notes
1 3F2144 SCREW - tapping, 1.7 x 4.0, nickel
2 3F6198 COVER - front, C300
3F9026 COVER - front, C310
3F9040 COVER - front, CD40
3 3F6200 BATTERY COVER AY - C300
3F9029 BATTERY COVER AY - C310
3F9042 BATTERY COVER AY - CD40
4 3F6197 DOOR - memory card, C300
3F9021 DOOR - memory card, C310
3F9039 DOOR - memory card, CD40
5 3F6199 COVER - back, C300
3F9027 COVER - back, C310
3F9041 COVER - back, CD40
6 3F2243 SCREW - tapping, 1.7 x 8.0, nickel
7 3F9022 SPRING - memory card door
8 3F9028 SPRING - battery cover, C310, CD40
9 3F6377 HINGE - battery cover, C310, CD40
------ 3F6285 DOCK INSERT - custom, C300
------ 3F9034 DOCK INSERT - custom, C310, CD40
------ 3F6279 WRIST STRAP - C300
------ 3F6387 WRIST STRAP - C310, CD40
1 5
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 2
1 1
1 1
1 1
1 1 Not visible in the graphic.
1 1 Not visible in the graphic.
1 1 Not visible in the graphic.
1 1 Not visible in the graphic.
10 31JAN06 – SM8784-1
Page 11
Figure 2 MONITOR LCD
1
1
Illustrated Parts List
red WIRE
black WIRE
2
2
3
3
P238_6503DCA
P238_6503DC
Figure 2 MONITOR LCD
Item Part No. Description Quantity Notes
1 5E8393 SCREW - tapping, 1.7 x 3.0, black
2 3F2207 LCD - monitor, C300
3F9020 LCD - monitor, C310, CD40
3 3F9030 LCD HOLDER, C310, CD40
2 1
2 1
2 1
2 1
SM8784-1 – 31JAN06 11
Page 12
SERVICE MANUAL
Figure 3 MCU BOARD AND LENS AY
1
1
2
2
3
3
P238_6504HCA
P238_6504HC
Figure 3 MCU BOARD AND LENS AY
Item Part No. Description Quantity Notes
1 3F2148 SWITCH - detector, 3 position
2 5E8393 SCREW - tapping, 1.7 x 3.0, black
3 3F6201 MCU BOARD AND LENS AY - C300
3F9031 MCU BOARD AND LENS AY - C310, CD40
3 1
3 3
3 1
3 1
12 31JAN06 – SM8784-1
Page 13
Figure 4 POWER BOARD AND FRAME AY and TAKE BOARD
2
2
3
3
4
4
1
1
Illustrated Parts List
Figure 4 POWER BOARD AND FRAME AY and TAKE BOARD
Item Part No. Description Quantity Notes
1 3F2244 WINDOW - flash
2 5E8393 SCREW - tapping, 1.7 x 3.0, black
3 3F6202 BOARD - take, C300
3F9032 BOARD - take, C310, CD40
4 3F6203 POWER BOARD AND FRAME AY -
C300
4 1
4 3
4 1
4 1
1
4
3F9033 POWER BOARD AND FRAME AY -
C310, CD40
4
------ 3F2252 SWITCH - detector, 2 position 4 1 • Not visible in the graphic.
• Located on the TAKE BOARD - see
“
TAKE BOARD” on Page 45.
----- 3F6204 FUSE - 1.25 A, F4
4 1 • Not visible in the graphic.
• Located on the POWER BOARD - see
“
POWER BOARD” on Page 44.
----- 3F6205 FUSE - 2.50 A, F1, F2, F3
4 3 • Not visible in the graphic.
• Located on the POWER BOARD - see
“
POWER BOARD” on Page 44.
P238_6502DCA
P229_6502DC
SM8784-1 – 31JAN06 13
Page 14
SERVICE MANUAL
Section 2: Alphabetical Index
Alphabetical Index
Part No. Description Figure No.
3F6202 BOARD - take, C300 4
3F9032 BOARD - take, C310, CD40 4
3F6199 COVER - back, C300 1
3F9027 COVER - back, C310 1
3F9041 COVER - back, CD40 1
3F6200 COVER - battery, C300 1
3F9029 COVER - battery, C310 1
3F9042 COVER - battery, CD40 1
3F6198 COVER - front, C300 1
3F9026 COVER - front, C310 1
3F9040 COVER - front, CD40 1
3F6285 DOCK INSERT - custom, C300 1
3F9034 DOCK INSERT - custom, C310, CD40 1
3F6197 DOOR - memory card, C300 1
3F9021 DOOR - memory card, C310 1
3F9039 DOOR - memory card, CD40 1
3F6204 FUSE - 1.25 A, F4 4
3F6205 FUSE - 2.50 A, F1, F2, F3 4
3F6377 HINGE - battery cover 1
3F2207 LCD - monitor, C300 2
3F9020 LCD - monitor, C310, CD40 2
3F9030 LCD HOLDER 2
3F6201 MCU BOARD AND LENS AY - C300 3
3F9031 MCU BOARD AND LENS AY - C310, CD40 3
3F6203 POWER BOARD AND FRAME AY - C300 4
3F9033 POWER BOARD AND FRAME AY - C310, CD40 4
5E8393 SCREW - tapping, 1.7 x 3.0, black 2, 3, 4
3F2144 SCREW - tapping, 1.7 x 4.0, nickel 1
3F2243 SCREW - tapping, 1.7 x 8.0, nickel 1
3F9028 SPRING - battery cover 1
3F9022 SPRING - memory card door 1
3F2252 SWITCH - detector, 2 position 4
3F2148 SWITCH - detector, 3 position 3
3F2244 WINDOW - flash 4
3F6279 WRIST STRAP - C300 1
3F6387 WRIST STRAP - C310, CD40 1
14 31JAN06 – SM8784-1
Page 15
Section 3: Diagnostics
Error Codes
E00
Description Recommended Action
A communication error occurred between the MAIN
CPU and the 8-BIT MCU.
E20
Description Recommended Action
A failure occurred when writing to the NAND FLASH. • Do “
• Do “
CARD” on Page 30.
• Install a new MCU BOARD AND LENS AY.
CARD” on Page 30.
• Install a new MCU BOARD AND LENS AY.
Diagnostics
Upgrading the Firmware Using the MEMORY
Upgrading the Firmware Using the MEMORY
SM8784-1 – 31JAN06 15
Page 16
SERVICE MANUAL
Diagnostic Tests
Checking for Low Voltage
Important
The BATTERY VOLTAGE ADJUSTMENT TOOL does not have a 2.50 V input. You must use the 2.6 V input.
[1] Connect the DIGITAL MULTIMETER to the BATTERY VOLTAGE ADJUSTMENT TOOL:
Color of
Wire
red “+”“2.5 V”
black “Ground”“Ground”
[2] Energize the DIGITAL MULTIMETER.
[3] Set the voltage on the DIGITAL MULTIMETER to 2.5 V.
[4] Install the CAMERA on the BATTERY VOLTAGE ADJUSTMENT TOOL.
[5] Set the SWITCHES on the BATTERY VOLTAGE ADJUSTMENT TOOL to:
•“2.5 V”
•“ON”
[6] Energize the CAMERA.
[7] Press the FLASH/STATUS BUTTON continually until the MONITOR LCD displays “FILL FLASH”.
[8] Press the SHUTTER BUTTON.
[9] Check:
• FLASH energizes
• image displays correctly
• MONITOR LCD displays the low BATTERY icon
DIGITAL
MULTIMETER
BATTERY VOLTAGE
ADJUSTMENT TOOL
Note
The results are not within specification if any of the following occurs:
• READY LIGHT next to the VIEWFINDER blinks red
• BATTERY icon blinks
• MONITOR LCD displays an error code
[10] Delete the image.
[11] De-energize the CAMERA.
16 31JAN06 – SM8784-1
Page 17
Checking for Uniform Flash
Diagnostics
Important
• A dark room or the GEN 2 CUSTOM TEST FIXTURE can be used.
• The distance is measured from the surface of the TARGET to the front of the LENS.
[1] If using:
Dark Room GEN 2 CUSTOM TEST FIXTURE with Controlled Light
Place the TARGET 1 m (39.4 in.) from the
front surface of the CAMERA.
[2] Install the CAMERA and the CAMERA DOCK on the CAMERA NEST.
[3] Connect to the CAMERA DOCK:
• AC ADAPTER
• USB CABLE
[4] Double-click the “Vista for Service” icon on the computer.
[5] If the MONITOR LCD displays “Date and time have been reset”, select “CANCEL”.
[6] Press the [Transfer] BUTTON on the CAMERA DOCK.
Place the TARGET in SLOT 5.
[7] Click the “Take” icon in the service software.
SM8784-1 – 31JAN06 17
Page 18
SERVICE MANUAL
[8] Click [Yes].
[9] Select “Flash Uniformity”.
[10] Click [OK].
[11] Check the mark on the computer screen.
Green “
The test was successful. A failure occurred.
✓” Red “X”
[12] Close the “Flash Uniformity” window.
18 31JAN06 – SM8784-1
Page 19
Checking the Power-On Self-Test
[1] Do Making the “C300_Self_Test” MEMORY CARD on Page 28.
[2] Do either of the following:
• Install the CAMERA on the CAMERA DOCK.
• Insert the BATTERIES in the CAMERA.
[3] Insert the “C300_Self_Test” MEMORY CARD into the CAMERA.
[4] Energize the CAMERA to execute the test.
[5] If the MONITOR LCD displays “Date and time have been reset”, click [CANCEL].
[6] For each test displaying on the MONITOR LCD, check for the following:
Test Check:
“F/W: n.nnnn” version of firmware
“RGB Level Checking...” quality of the 6 colors
“Gray Level Checking...” quality of the 6 gray areas
“LEDs On/Off testing”•green LED on the front of the CAMERA illuminates
• red and green LEDs on the back of the CAMERA illuminate
“LCD On/Off testing” MONITOR LCD blinks
“Strobe testing” STROBE energizes once
“SDRAM testing”•“SDRAM OK”
“IDRAM testing”
“SD card testing”
“NAND flash testing”
“Temperature checking...” message “OK”
“LCD Bad pixel testing” MONITOR LCD for:
•“IDRAM OK”
•“SD Card OK”
•“NAND Flash OK”
• dark pixels in the white screen
• white pixels in the dark screen
Diagnostics
[7] When the test is completed, de-energize the CAMERA.
[8] Remove the “C300_Self_Test” MEMORY CARD.
SM8784-1 – 31JAN06 19
Page 20
SERVICE MANUAL
Checkout Procedures
Checking the General Functions of the CAMERA
Important
Do these procedures before you return the CAMERA to the customer.
[1] Remove the BATTERY from the CAMERA.
[2] Install the CAMERA on the CAMERA DOCK.
[3] Check that the READY LIGHT LED on the CAMERA DOCK illuminates green.
[4] Remove the CAMERA from the CAMERA DOCK.
[5] Install:
• CRV3 BATTERY into the CAMERA
• CAMERA on the CAMERA DOCK
[6] Check:
• READY LIGHT LED on the CAMERA DOCK illuminates green
• STATUS LEDs on the CAMERA DOCK do not illuminate
[7] Remove:
• CAMERA from the CAMERA DOCK
• BATTERY from the CAMERA
[8] Insert a MEMORY CARD into the CAMERA.
[9] Install the CAMERA on the CAMERA DOCK.
[10] Rotate the MODE DIAL on the CAMERA to the “AUTO” position.
[11] Check the energizing sequence.
(a) The green LED on the CAMERA DOCK illuminates.
(b) The READY LIGHT LED on the CAMERA:
• blinks green during the energizing sequence
• remains illuminated green after the energizing sequence
(c) No error code displays on the MONITOR LCD.
[12] De-energize the CAMERA.
[13] Remove the CAMERA from the CAMERA DOCK.
[14] Install a new BATTERY or BATTERY PACK that has a full charge.
[15] Rotate the MODE DIAL on the CAMERA to the “AUTO” position.
[16] Check the energizing sequence.
(a) The READY LIGHT LED on the CAMERA:
• blinks green during the energizing sequence
• remains illuminated green after the energizing sequence
(b) No error code displays on the MONITOR LCD.
20 31JAN06 – SM8784-1
Page 21
[17] Check:
BUTTON Do:
•“menu”
• UP CONTROLLER
• DOWN CONTROLLER
•“OK”
• SHUTTER
1. Press the “menu” BUTTON.
2. Check that the MONITOR LCD illuminates.
3. Press the following to move through the menu:
• UP CONTROLLER BUTTON
• DOWN CONTROLLER BUTTON
4. Press:
•“OK” BUTTON to view the options
•“OK” BUTTON again to return to the preceding screen
•“menu” BUTTON
•“OK” BUTTON again
5. Check that the MONITOR LCD displays the “liveview” mode.
6. Press the SHUTTER BUTTON.
7. Check that the MONITOR LCD displays the captured image.
•“review”
• LEFT CONTROLLER
• RIGHT CONTROLLER
•“share”
1. Press the “review” BUTTON.
2. Check that the MONITOR LCD displays an image.
3. Press:
• LEFT CONTROLLER BUTTON
• RIGHT CONTROLLER BUTTON
4. Check that the images displayed on the MONITOR LCD change.
5. Press the “share” BUTTON.
6. Check that the options display.
7. Press:
•“share” BUTTON again
•“review” BUTTON
8. Check that the MONITOR LCD de-energizes.
9. Press:
•“review” BUTTON again
• SHUTTER BUTTON
10. Check that the MONITOR LCD displays the captured image.
FLASH 1. Press the FLASH BUTTON.
2. Check that the MONITOR LCD:
• illuminates
• de-energizes after 5 seconds
3. Press the FLASH BUTTON continually.
4. Check that the MONITOR LCD displays:
•“AUTO FLASH”
•“FLASH OFF”
•“FILL FLASH”
•“RED EYE”
5. Press the SHUTTER BUTTON.
6. Check that the MONITOR LCD displays the captured image.
Diagnostics
SM8784-1 – 31JAN06 21
Page 22
SERVICE MANUAL
BUTTON Do:
SHUTTER 1. Press the SHUTTER BUTTON.
2. Check:
• green LED blinks once before the CAMERA captures the image
• green LED blinks during the time the CAMERA stores the image
“delete” 1. Press:
•“review” BUTTON
•“delete” BUTTON
2. Check that options display.
3. Press:
•“OK” BUTTON to select the option “EXIT”
•“review” BUTTON
•“review” BUTTON again
•“delete” BUTTON
• SHUTTER BUTTON
4. Check that the image is not deleted.
5. Press:
•“review” BUTTON
•“delete” BUTTON
6. Select “PICTURE”.
7. Press the “OK” BUTTON.
8. Check that the image is deleted.
9. Press:
•“OK” BUTTON
•“review” BUTTON
[18] Press the “OK” BUTTON to start the “Liveview” mode.
[19] Press and hold the RIGHT CONTROLLER BUTTON to start the “Zoom” mode.
[20] Check that the magnification of the image on the MONITOR LCD increases.
[21] Press and hold the LEFT CONTROLLER BUTTON.
[22] Check that the magnification of the image on the MONITOR LCD decreases.
[23] Press:
•“OK” BUTTON to exit the “Liveview” mode
• SHUTTER BUTTON to capture an image
[24] Check that the following display on the MONITOR LCD:
• image
• mode of the FLASH icon
• image quality icon
• internal memory or MEMORY CARD icon
• number of remaining images that can be captured
22 31JAN06 – SM8784-1
Page 23
Checking the ACTUATION, FLASH, and POWER-ON COUNTERS
[1] Energize the CAMERA.
[2] Press the “menu” BUTTON.
[3] Select “SETUP MENU”.
[4] Press the “OK” BUTTON.
[5] Select “ABOUT...”.
[6] Press the “OK” BUTTON.
[7] At the same time, press:
• left CONTROLLER BUTTON
•“delete” BUTTON
[8] Press the top CONTROLLER BUTTON.
[9] Record the information for the COUNTERS in the FEEDBACK SOFTWARE.
COUNTERS on the CAMERA Description on the FEEDBACK SOFTWARE
ID “ID of production Serial Number”
BV “Boot code Version”
MV “Micro processor code Version”
CS “Actuation”
CF “Flash”
CP “Power On”
Diagnostics
[10] Press the “OK” BUTTON.
Checking the External Components of the CAMERA
[1] Check the COVERS for scratches.
[2] If necessary, install new COVERS.
[3] Clean:
• COVERS
• SCREEN on the MONITOR LCD
• VIEWFINDER
• FLASH WINDOW
• LENS
[4] Check the LENS for damage.
SM8784-1 – 31JAN06 23
Page 24
SERVICE MANUAL
Section 4: Adjustments
SHUTTER - Delay
Adjustment Specification
Purpose: To adjust the delay of the SHUTTER.
Do When: After installing a new MCU BOARD AND LENS AY.
Specification: MONITOR LCD displays the message “Shutter Calibrate OK!”.
Special Tools: •“C300_Shutter_Delay” MEMORY CARD
• LIGHT BOX - Arrowin LBF, 2001
• BATTERIES - 2 OXY-ALKALINE or 1 Ni-MH BATTERY PACK, for the CAMERA
Prerequisites:
None
To Check:
You cannot check this adjustment.
To Adjust:
Important
Do not use the CAMERA DOCK for this procedure.
[1] Do “
[2] Insert in the CAMERA:
The LENS must be 3 mm (0.1 in.) from the LIGHT BOX.
[3] Place the CAMERA to the front of the LIGHT BOX.
[4] Set the LIGHT BOX to LV15.
[5] Energize the CAMERA to execute the test.
[6] If the MONITOR LCD displays “Date and time have been reset”, select “CANCEL”.
[7] Check that the MONITOR LCD displays “Shutter Calibrate OK!”.
[8] When the test is complete, de-energize the CAMERA.
[9] Remove the “C300_Shutter_Delay” MEMORY CARD.
Making the MEMORY CARDS for Service” on Page 28.
• 2 OXY-ALKALINE BATTERIES or 1 Ni-MH BATTERY PACK
•“C300_Shutter_Delay” MEMORY CARD
Important
Postrequisites:
None
24 31JAN06 – SM8784-1
Page 25
CCD - White Balance
Adjustment Specification
Purpose: To measure and store values for color correction.
Do When: • The color of the images is not correct.
• After installing a new MCU BOARD AND LENS AY.
Specification: MONITOR LCD displays the message “Store bad pixel rec...Calibration OK”.
Special Tools: •“C300_AWB_ISO” MEMORY CARD
• LIGHT BOX - Arrowin LBF, 2001
• BATTERIES - 2 OXY-ALKALINE or 1 Ni-MH BATTERY PACK, for the CAMERA
Prerequisites:
None
To Check:
You cannot check this adjustment.
Adjustments
To Adjust:
Important
Do not use the CAMERA DOCK for this procedure.
[1] Do “
[2] Insert the “C300_AWB_ISO” MEMORY CARD into the CAMERA.
[3] Set the LIGHT BOX to LV10.
Making the MEMORY CARDS for Service” on Page 28.
Important
The CAMERA must be 3 mm (0.1 in.) from the LIGHT BOX.
[4] Place the CAMERA to the front of the LIGHT BOX.
[5] Energize the CAMERA to execute the test.
[6] If the MONITOR LCD displays “Date and time have been reset”, select [CANCEL].
[7] Check that the message “Store bad pixel rec...Calibration OK” displays on the MONITOR LCD.
[8] De-energize the CAMERA.
[9] Remove the “C300_AWB_ISO” MEMORY CARD.
Postrequisites:
None
SM8784-1 – 31JAN06 25
Page 26
SERVICE MANUAL
Section 5: Replacements
Important
See “Equipment Parts” on Page 9.
26 31JAN06 – SM8784-1
Page 27
Additional Service Procedures
Section 6: Additional Service Procedures
Installing the Altek VISTA SERVICE SOFTWARE on the Computer
[1] From the Kodak Partner Site, download the software and firmware files for the Kodak EasyShare
C300 DIGITAL CAMERA.
[2] Right-click the “Vista For Service V4.1.0.3.zip” file.
[3] Select Winzip >Extract to here.
[4] Open the folders:
•“Vista for Service V4.1.0.3”
•“Setup”
[5] Double-click the file “Setup.exe”.
[6] Do the instructions that appear on the screen.
Note
The “Vista for Service” icon is now available on the computer.
SM8784-1 – 31JAN06 27
Page 28
SERVICE MANUAL
Making the MEMORY CARDS for Service
Downloading the Files from the Partner Site
[1] If necessary, from the Kodak Partner Site
download the software and firmware files for the
Kodak EasyShare C300 DIGITAL CAMERA.
[2] Select the “script4service(C300).zip” file.
[3] Click [Extract].
[4] Select a folder.
[5] Click [Extract] again.
[6] Check that 3 new folders were written:
•“master camera”
•“self test”
•“shutter delay”
These folders have files that you will use to make the
following 3 MEMORY CARDS for service:
•“C300_Self_Test”
•“C300_Shutter_Delay”
•“C300_AWB_ISO”
Making the “C300_Self_Test” MEMORY CARD
[1] Double-click the “self test” fold er.
[2] Make a copy of the “autoexe.dsc” file to a blank MEMORY CARD.
[3] Label the MEMORY CARD “C300_Self_Test”.
Note
Making the “C300_Shutter_Delay” MEMORY CARD
[1] Double-click the “shutter delay” folder.
[2] Make a copy of the “autoexe.dsc” file to a blank MEMORY CARD.
[3] Label the MEMORY CARD “C300_Shutter_Delay”.
28 31JAN06 – SM8784-1
Page 29
Making the “C300_AWB_ISO” MEMORY CARD
[1] Double-click the “master camera” folder.
[2] Make a copy of the following files to a blank MEMORY CARD:
•“AUTOEXE.DSC”
•“wipocali.dsc”
[3] Label the MEMORY CARD “C300_AWB_ISO”.
[4] Obtain a MASTER CAMERA.
[5] Insert new BATTERIES or a BATTERY PACK with a full charge into the CAMERA.
[6] Insert the “C300_AWB_ISO” MEMORY CARD into the CAMERA.
Additional Service Procedures
[7] Set the CAMERA in front of the LIGHT BOX:
• 3 mm (0.1 in.) from the LIGHT BOX
• center of the LENS at the center of the light
[8] Set the LIGHT BOX to LV10.
[9] Energize the CAMERA to execute the test.
[10] If the MONITOR LCD displays “Date and time have been reset”, select “CANCEL”.
[11] When the test is completed, check that the MONITOR LCD displays “OK Light Box Cali”.
[12] De-energize the CAMERA.
[13] Remove the MEMORY CARD.
[14] Check that the following files were written on the MEMORY CARD:
•“AUTOEXE.DSC”
•“lamplv.inf”
•“lampwp.inf”
•“lampcali.dsc”
SM8784-1 – 31JAN06 29
Page 30
SERVICE MANUAL
Upgrading the Firmware Using the MEMORY CARD
[1] Insert a blank MEMORY CARD into the MULTI-CARD READER.
[2] Use the computer to format the MEMORY CARD.
[3] Make:
• folder on the MEMORY CARD with the name “System”
• copy of the new “KC300.fw” file
[4] Place the new “KC300.fw” file in the “System” folder on the MEMORY CARD.
[5] Remove the MEMORY CARD from the MULTI-CARD READER.
[6] Insert the MEMORY CARD into the CAMERA.
[7] Are you using the CAMERA DOCK to energiz e the CAMERA?
Yes No
a. Connect the AC ADAPTER.
b. Check that the CAMERA DOCK is not connected
to the computer.
c. Insert the CAMERA into the CAMERA DOCK.
d. Energize the CAMERA.
[8] Select:
•“UPGRADE”
•“CONTINUE”
[9] When the upgrade is complete, select “Exit”.
[10] Remove the MEMORY CARD.
[11] De-energize the CAMERA.
[12] Energize the CAMERA.
[13] Press the “menu” BUTTON.
[14] Select “SETUP MENU”.
[15] Press the “OK” BUTTON.
[16] Select “ABOUT...”.
[17] Press the “OK” BUTTON.
[18] Check:
• correct firmware version displays on the MONITOR LCD
• CAMERA operates correctly
a. Insert new BATTERIES or a BATTERY PACK
with a full charge into the CAMERA.
b. Check that the CAMERA is not connected to the
computer.
c. Energize the CAMERA.
30 31JAN06 – SM8784-1
Page 31
Additional Service Procedures
Upgrading the Firmware Using the Internal Memory
[1] Remove the MEMORY CARD from the CAMERA.
[2] Are you using the CAMERA DOCK or BATTERIES to energize the CAMERA?
CAMERA DOCK BATTERIES
a. Connect:
• CAMERA DOCK to the computer using the
USB CABLE
• AC ADAPTER
b. Insert the CAMERA into the CAMERA DOCK.
c. Energize the CAMERA.
d. Press the TRANSFER BUTTON on the CAMERA
DOCK.
[3] Double-click:
•“My Computer”
• corresponding drive for the C300 DIGITAL CAMERA
•“Internal Memory” folder
[4] Make a copy of the “KC300.fw” file.
[5] Place the copy of the “KC300.fw” file in the “Internal Memory” folder.
[6] De-energize the CAMERA.
[7] Remove either the CAMERA from the CAMERA DOCK or the USB CABLE from the CAMERA.
[8] Energize the CAMERA.
[9] Select:
•“UPGRADE”
•“CONTINUE”
[10] When the upgrade is complete, de-energize the CAMERA.
[11] Energize the CAMERA.
[12] Press the “menu” BUTTON.
[13] Select “SETUP MENU”.
[14] Press the “OK” BUTTON.
[15] Select “ABOUT...”.
[16] Press the “OK” BUTTON.
[17] Check:
• correct firmware version displays on the MONITOR LCD
• CAMERA operates correctly
a. Insert new BATTERIES or a BATTERY PACK
with a full charge into the CAMERA.
b. Connect the CAMERA to the computer using the
USB CABLE.
c. Energize the CAMERA.
SM8784-1 – 31JAN06 31
Page 32
32 31JAN06 – SM8784-1
Block
System Overview
SERVICE MANUAL
Section 7: Diagrams
Take button
Take board
Bat. Type Det.
Flash light
P238_0022FA_
5 way button
W ok T
Strobe
Cap.
Mode Dial
Video/Auto/Night SW
MCU3.3V
Flash TRG
Flash
Trigger
circuit
Bat. Temp.
sensor
Dock PWR 3.3V
Flash
Charge
Circuit
Lens
3.3V
I/F
Flash RDY
LED R,G.
Flash CHR
3.3V
5.5V
3M
CCD
V Dri.
15V & -8.5V shutter
I2C
Reset_in
uP
SD1 ON6
MCU 3.3V
15.5V
-8.0V
3.3V
1.8V
M3.3V
5.5V
4.9152
32.768
Flash TRG
I/F
.
MHz
KHz
SD2~4
DC/DC
convert
Sig.
in
12
MHz
Card
CDS/AD
H1/H2/RG
SD
DC cont.
10 bit
ASIC
Video out
FB4
USB
conn.
DOCK_PWR
Power sel.
F2
Self timer LED
SDRAM
(4Mx16)
Share,Dock det.,battery charge
Dock
DC_ PWR
F1
NandFlash
(16Mx8)
BootRom
(64Kx8)
Dock Batt+
Battery
3.3V
5.5V
1.5 inch
Color LCD
LED backlight
7V
System Overview
15V
feedback
Page 33
Schematic
MCU BOARD - 1 of 6
Diagrams
MCU BOARD
1 of 6
P238_0030EC_
SM8784-1 – 31JAN06 33
Page 34
SERVICE MANUAL
MCU BOARD - 2 of 6
MCU BOARD
2 of 6
P238_0031EC_
34 31JAN06 – SM8784-1
Page 35
MCU BOARD - 3 of 6
Diagrams
MCU BOARD
3 of 6
P238_0032EC_
SM8784-1 – 31JAN06 35
Page 36
SERVICE MANUAL
MCU BOARD - 4 of 6
MCU BOARD
4 of 6
P238_0033EC_
36 31JAN06 – SM8784-1
Page 37
MCU BOARD - 5 of 6
Diagrams
MCU BOARD
5 of 6
P238_0034EC_
SM8784-1 – 31JAN06 37
Page 38
SERVICE MANUAL
MCU BOARD - 6 of 6
MCU BOARD
6 of 6
P238_0035EC_
38 31JAN06 – SM8784-1
Page 39
POWER BOARD - 1 of 3
Diagrams
POWER BOARD
1 of 3
P238_0027EC_
SM8784-1 – 31JAN06 39
Page 40
SERVICE MANUAL
POWER BOARD - 2 of 3
POWER BOARD
2 of 3
P238_0028EC_
40 31JAN06 – SM8784-1
Page 41
POWER BOARD - 3 of 3
Diagrams
POWER BOARD
3 of 3
P238_0029EC_
SM8784-1 – 31JAN06 41
Page 42
SERVICE MANUAL
TAKE BOARD
TAKE BOARD
P238_0026DC_
42 31JAN06 – SM8784-1
Page 43
Component Locator
MCU BOARD
Diagrams
Top
Bottom
P238_0023EC_
SM8784-1 – 31JAN06 43
MCU BOARD
Page 44
SERVICE MANUAL
POWER BOARD
F1
F4
Top
F2
F3
Bottom
P238_0024EC_
44 31JAN06 – SM8784-1
POWER BOARD
Page 45
TAKE BOARD
Diagrams
2 position
DETECTOR SWITCH
Top
Bottom
TAKE BOARD
P238_0025EC_
SM8784-1 – 31JAN06 45
Page 46
Section 8: Publication History
Publication History
Publication
Date
05APR05 SM8784-1 --- sm8784_1.fm New Publication
27APR05 SM8784-1 8 sm8784_1.fm Added 2 parts.
31JAN06 SM8784-1 7
Publication
No.
Changed
Pages
9 - 14
File
Name Notes
sm8784_1.fm Added the following information for the
Kodak EasyShare C310 DIGITAL CAMERA and
the Kodak EasyShare CD40 DIGITAL CAMERA:
• Catalog Numbers in the “
New CAMERAS” on Page 7
• Part numbers in the Illustrated Parts Lists in
Equipment Parts
Reference Table for
Kodak and EasyShare are trademarks of Eastman Kodak Company.
Printed in U.S.A. • sm8784_1.fm
EASTMAN KODAK COMPANY
Rochester, NY 14650
Loading...