Kodak 7020, 9020, 9010, 7010 User Manual

KODAK EKTAPRO
7010/7020/9010/9020
Slide Projector

SUPPLEMENT TO THE MANUAL

©Eastman Kodak Company, 2000

Function Codes

This label is designed to be fixed on the rear of your IR
Remote System (transmitter).

Function Code

• Dissolve times
(0.1 - 9.9 s)
CUT

Random Access 0-160

Fade:
MASTER
SLAVE

Alternate 777
Freeze 789

• Independent
Projector Control
Mode

• Parallel
projection
Focus Slave

• Reactivating
dissolve mode

• Remote Security
Mode

Reset 999
Autotimer

(1-60 s)

----- off

*

801 - 899
800

770
707

980

970
666*

990

989

601 - 660
600

* Function is inactivated for models

7010 and 9010!

5

Presentations with KODAK EKTAPRO 7010, 7020, 9010 and 9020 Slide Projectors

Oneoftheimportant newfeatures ofthe KODAKEKTAPRO
7010,7020, 9010and 9020Slide Projectorsis theintegrated
dissolver for a 2-projector dissolve.
You just have to link two projectors using the KODAK
Dissolve Cable (accessory) and you can immediately run
more interesting and lively live presentations using the
infrared remotecontrol. It is also possible to play automatic
slide shows with a fixed dissolve time. However, it is not

possible to record the IR-commands.

Projection with a single projector
(Soft Slide Change)

If you are just presenting with a single EKTAPRO 7010,
7020, 9010or 9020, youcan fade yourslides out andback in
again (e.g. bysetting a dissolve timeto smoothly change the
slides). This means the hard light change is avoided during
slide transport.
The commands and notes which relate to the control of an
individual projector are marked with an *.

Projection with two projectors

Choosing projectors (MASTER/SLAVE)

All commandsfor dissolving etc.are only transmittedto one
projector. This projector is called the MASTER. It passes
the commands onto the second projector which isknown as
the SLAVE.

• You can use either the KODAK EKTAPRO 7010, 7020,

9010 or 9020 projector as a MASTER

• However, you can use all EKTAPRO models with a

P-Bus-in interface as a SLAVE!

Note: The use of all functions is only possible via
EKTAPRO IR-Remote Control! With the KODAK
EKTAPRO Cable Remote only dissolves in the default
setting (0.5 sec) can be carried out.

Setting up

Putting your 2 projector dissolve systemtogether is fast and
easy.Connect the twoprojectors viathe P-bus-ininterface to
the KODAK Dissolve Cable (accessory) as shown in the
illustration! Connect your remote control to the MASTER
projector! Switch the projectors on. Your 2 projector
dissolve system is now ready to use.

Comments

• Evenwhen the two projectors are linkedwith the dissolve
cable, theybehave like individual projectorsand can also
be operated individually as usual via the keypad.

• If your SLAVE projector has a built-in timer, it must be
switched off!

• If you want to use only one projector in single mode,
simply switch off the SLAVE and use the MASTER!

Aligning the projectors

It is important to align the two slide projectors before
beginning a presentation such that both projected images
cover the same area. This is easiest using so-called aligning
slides which your AV dealer will certainly carry in stock (it
is useful to load the aligning slide in the tray
compartment 80):

• Place the slide trays onto the projectors.

• Pressthe slide reverse transport buttonon both projectors.

• Focus both slides using the focus buttons on your
projectors.

• Nowalign theprojectors toproject bothslides on the same
area.

• Now return both slide trays to their initial position (zero
position).

You can now begin your presentation using the remote
control.

Comment (EKTAPRO 7010, 7020, 9010 or 9020)

If it is necessary to carry out any additional adjustment
during the presentation push both transport buttons on the
“dark” projector for longer than one second. The “dark”
projector is now faded in too. Switch-off the lamp again by
pressing standby.

Sorting slides into the slide trays

Once you have decided on the order of your slides, number
them through. Then sort all the slides with uneven numbers
in sequence into the slide tray for the MASTER projector.
The slides with even numbers are sorted in order into the
slide tray for the SLAVE projector (see the table page 34).

6