Klark Teknik DN9340 User Manual

HELIX SYSTEM

DN9340 / DN9344

OPERATORS MANUAL

DN9340 Software V2.05
DN9344 Software V2.02

Klark Teknik Group,

Klark Teknik Building,

Walter Nash Road,

Kidderminster.

Worcestershire.

DY11 7HJ.

England.

Tel:[phone]

Fax:[phone]

Email: [e-mail]

Website: www.klarkteknik.com

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

AVIS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

RISQUÉ DE CHOC ELETRIQUE. NE PAS OUVRIR

These symbols are internationally accepted symbols that warn of potential hazards with
electrical products.

The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateraltriangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturers
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that
produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all testing to qualified personnel. Servicing isrequiredwhentheapparatusisdamagedinany way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,orhasbeendropped.

Walter Nash Road, Kidderminster, Worcestershire. DY11 7HJ. England

Tel: [phone]. Fax: [phone]

Company Registration No: 2414018

abc abc

SIGNAL PROCESSING BY DEFINITION DESIGNEDFOR APUREPERFORMANCE

DECLARATION OF CONFORMITY

Klark Teknik Group (UK) PLC

We,

of, Klark Teknik Building, Walter Nash Road, Kidderminster, Worcestershire, DY11 7HJ

Declare that a sample of the following product:-

Product Type Number Product Description Nominal Voltage (s) Current Freq

DN9340 Digital Equaliser 115V AC 200mA
DN9344 230V AC

100mA

to which this declaration refers, is in conformity with the following directives and/or standards:-

Directive(s) Test Standard(s)

89/336/EEC Electromagnetic Compatibility Directive
amended by 92/31/EEC & 93/68/EEC 73/23/EEC,
Low Voltage Directive, amended by 93/68/EEC
Generic Standard Using EN50130 Limits and Methods EN50081/1
Class B Conducted Emissions
Class B Radiated Emissions

EN50130

EN50130
Fast Transient Bursts at 2kV EN61000-4-4
Static Discharge at 4kV EN61000-4-2
Electrical Stress Test EN60204
Electrical Safety UL6500-99

E60065-00

50/60Hz

Signed:............................

Date: 24th April 2003

Name: Simon Harrison

Authority: R&D Director, Klark Teknik Group (UK) PLC

Attention!
Where applicable, the attention of the specifier, purchaser, installer or user is drawn to special limitations of use
which must be observed when these products are taken into service to maintain compliance with the above
directives. Details of these special measures and limitations to use are available on request and are available
in product manuals.

A Subsidiary of Telex communications, Inc.

Contents

l abc

Thank you for using a Klark Teknik product
After you have unpacked

Quick reference

Introduction and key features

Identification of controls: DN9340

Connections: DN9340

Signal flow: DN9340

Operation: DN9340

Home page 17
Graphic equalisation 19
Parametric equalisation 22

T-DEQ

Dynamic equalisation 24
Filters 26
Storing and recalling settings 28
Setup menu 29
Metering 30
Clear down sequence 31

1
3

5

7

9

13

15

Remote Control

Identification of controls: DN9344

Signal flow: DN9344

Operation: DN9344

Remote Control Mode 42
Contact Closure (RELAY) Mode 43
Stand Alone Mode 44

Application notes:

Application note 1: dynamic EQ 45

T-DEQ

Application note 2: What do we mean by all these Q types? 48

Technical specifications: DN9340
Technical specifications: DN9344
Service Information

32

37

41

51
52
53

l abc

.

The Klark Teknik Helix System

Thank you for selecting the Klark Teknik Helix System digital equaliser. The equaliser continues the Klark
Teknik tradition of providing superb audio performance, technical accuracy and rugged reliability. At the
same time it offers unprecedented levels of flexibility by incorporating graphic, parametric and dual­threshold dynamic equalisation ( ) in a single unit. In view of this flexibility we hope that you will
spend a little time to read this manual, as this will allow you to obtain the very best results with minimum
effort. Wealso draw youattention to the“Important safety information” page at the beginningof the manual.
For those of you in a hurry, the quick reference guides are on pages 5 and 6.

T-DEQ

l abc

Precautions

Do not install this unit in a location subjected to excessiveheat, dust or mechanical vibration.

Voltage Selectionand PowerConnection

Connection is made by means of anIEC standard powersocket. The rear panel text indicatesthe voltage range
required for satisfactory operation of the unit.

Before connecting this unit to the mains supply, ensure the fuse fitted is the correct type and rating is as
indicated on the rear panel, adjacent to the fuse holder.

Safety Warning

This unit is fitted with a standard fused IEC mains inlet: For safety reasons the earth lead should never be
disconnected.

To prevent shock or fire hazard, do not expose the unit to rain or moisture. To avoid electrical shock do not
remove covers. Refer servicing to qualified personnel only.

Attention! Cables

This product should only be used with high quality, screened twisted pair audio cables, terminated with metal
bodied 3-pin XLR connectors. Any other cable type or configuration for the audio signals may result in
degraded performance due to electromagnetic interference.

Electric Fields:

Should this product be used in an electromagnetic field that is amplitude modulated by an audio frequency
signal (20Hz to 20kHz), the signal to noise ratio may be degraded. Degradation of up to 60dB at a frequency
corresponding to the modulation signal may be experienced under extreme conditions (3V/m, 90%
modulation).

1

l abc

2

After You Have Unpacked The Unit

Save all the packing materials - they will prove valuable should it become necessary to transport or ship this
product.

Please inspect this unit carefully for any signs of damage incurred during transportation. It has undergone
stringent quality control inspectionand every possible effort has been made to ensure that it left the factory in
perfect condition.

If, however, the unit shows any signs of damage, please notify the transportation company without delay.
Only you, the consignee, may institute a claim against the carrier for damage during transportation.

If necessary, contact your supplier or as a last resort, your Klark Teknik importing agent, who will fully co­operate under such circumstances.

l abc

Side Up

This

KIDDERMINSTER ENGLAND

3

l abc

4

Quick reference: DN9340

Power ON indication.

The left, centre and right encoder knobs ­used for controlling values and selecting
options.

l abc

Power switch.

Output metering incorporating multi-point
clip indication.

Alphanumeric display - this showsparameter
values for the current function being
controlled by theencoder knobs.

Soft keys for selecting options and secondary
functions.

This area of the main graphic display labels
the soft key functions. Typically these
include “select” to choose a particular filter,
and “menu” to step round a circular choice of
options for that type of EQ. On the home
page these buttons access the gain, delay,
naming functions.

T-DEQ

Input metering incorporating multi-point clip
indication.

HOME(SETUP) key. Press once to return to
the home page. Once on the home page, press
and hold for one second to access the Setup
menu. Step through the Setup menu (and exit
after the last item) by repeatedly pressing this
key.

STORE and RECALL keys. Used to store
complete unit settings to one of the 64
memory locations andthen to recallthem.

PC port connector. Use with the supplied
cable to install software updates or to control
the unit froman external computer.

dynamic EQ metering.

Main graphic display - this shows the
frequency response of the selected type of
EQ, or theoverall response onthe home page.

EQ active lights - these show if a particular
type of EQ is currently affecting the overall
frequency response.

Access keys to control each type of
equalisation - press HOME(SETUP) key to
return to thehome page.

If you have received the unit in an unknown
state, and wish to clear it down to ensure
that no EQ is active, please refer to the
information on page 29.

Two part touchstrip. Press either part briefly
to select a particular filter or fader. In
Graphic EQ mode, press and hold to increase
the level (upper strip) or reduce it (lower
strip).

Channel select key. Press to select either
channelAor B for control. If the unit is linked
for stereo operation then both indicators will
be lit.

Bypass key - on the home page this bypasses
the complete unit for the selected channel
(both channels if linked). When a particular
EQ type is selected (by the keys above the
bypass switch), the bypass operates on that
type of EQonly.

5

Quick reference: DN9344

l abc

Power on indicator.

The large red alphanumeric displays can be used to
show electronic scribble-strip information, Last
Memory Recalled, andCommunications Mode.

Display mode indicator (blue) for Section 2. When lit
this indicates that the large red displays are now
showing Last Memory Recalled and
Communications Mode. When not lit, the displays
are showing electronic scribble-strip names. In this
case the left-hand three characters show the name of
Channel A and the right-hand three the name of
Channel B.

Power switch.

Section 2 output metering incorporating multi-point
clip indication.

Section 2 dynamic EQ metering.

Section 2 input metering incorporating multi-point
clip indication.

UP and DOWN keys for Section 2. Used to select
communications channel (address) for remote control
and also contact closure mode. Active only when in
SETUPmenu.

Communications traffic indicators. These indicate
when there is activity on any of the external
interfaces. Transmit and receive data are shown for
front panel (RS-232) and rear panel (RS-485) data,
and also thecontact closure (RELAY) input.

T-DEQ

SETUP key. Press and hold to enter SETUP menu. A
momentary press toggles between the electronic
scribble-strip displays and display of Last Memory
Recalled and Communications Mode.
Communications Mode isnot editable when display is
accessed this way.

UP and DOWN keys for Section 1. Used to select
communications channel (address) for remote
control and also contact closure mode. Active only
when in SETUPmenu.

Display mode indicator (blue) forSection 1. When lit
this indicates that the large red displays are now
showing Last Memory Recalled and
Communications Mode. When not lit, the displays
are showing electronic scribble-strip names. In this
case the left-hand three characters show the name of
Channel A and the right-hand three the name of
Channel B.

PC port connector. Use with the supplied cable to
install software updates or to control the unit from an
external computer.

Section 1 output metering incorporating multi-point
clip indication.

Section 1 dynamic EQ metering.

Section 1 input metering incorporating multi-point
clip indication.

Scribble-strip areas to allow easy labelling of the unit.
Use only chinagraph pencils to avoid permanently
marking the unit. Remove chinagraph markings by
wiping with a soft cloth. Do not use solvents as these
may damage thesurface.

T-DEQ

Remote ControlActive indicator (green) for Channel
1A. This shows that that the master unit is currently
controlling this channel by remote control. Often
referred to asthe “me” light.(repeat for 1B/2A/2B).

6

Introduction and key features

l abc

The Klark Teknik DN9340 Helix equaliser is a two-channel audio equaliser packaged in a 2RU, 19” rack­mounting format. The two channels can be controlled independently as two separate mono equalisers or
linked for stereo operation. The unit has been designed to build on Klark Teknik's unrivalled reputation for
high quality equalisation whilst addressing a number of limitations in more conventional products.

The Klark Teknik DN9344 Helix Slave equaliser is a 1U slave version of the DN9340 unit. By packaging
FOUR channels of Helix processing into a 1U case it offers unrivalled space efficiency, with a cost per
channel lower than many less flexible products. The DN9344 can be controlled from a master DN9340 unit
or by an external computer,and also has provision for contact closure operation.

Simultaneous availability of graphic and parametric equalisation.

·

In addition to the obvious
advantages of a dual-purpose unit, this allows the engineer to separate out different sections of
equalisation. For example, during setup and any soundcheck, the parametric mode can be used to set
a basic EQ for the venue, with maximum flexibility. Once the show starts, however, the engineer can
flip to graphic mode, which now starts off from a`flat' baseline. Any problems that needfast attention
during the show can now be addressed using the speed of operation of graphic EQ, and without
confusion between the `showtime' EQ and the original venue setup. At any time, a quick look at the
home page will show the true overall response of the unit.

Threshold Dependent Dynamic EQ ( ).

·

T-DEQ

Over the years a number of dynamic EQ products
have been introduced. These typically resemble a combination of a dynamics processor and an
equaliser. This approach has the disadvantage that whilst it is usually fairly easy to determine the
level at which the dynamic EQ willstart to operate, it ismuch harder to visualisethe likely effect as the
system is pushed harder or to set a maximum amount of EQ. The unique system developed by

T-DEQ

Klark Teknik with its dual thresholds provides unrivalled clarity of operation making this a very
practical tool.

Speed of operation.

·

Since the advent of digital signal processors, it has been possible to pack ever
more functions into smaller boxes. However, if a function is buried in a hard-to-find sub-menuwhich
is only accessible after navigating a complex series of button presses, it may as well not be included.
In live production theoperation ofthe unit is as crucial as the sound quality, and this is a key part of the
Helix design. The 2RU format permits a large graphic LCD display, and a second alphanumeric
display provides clear value readouts above the control knobs without using up space on the main
LCD. Dedicated selection buttons for the main functions, clear LED indicators, and no less that 8
separate bargraph meters ensure that the unit is fast and accurate inoperation. The unique two-section
touchstrip provides instant access to filters andfaders, so that Helix providesthe same feeling ofbeing
“in control” familiar to users of Klark Teknik analogue graphic equalisers.

·

Space efficiency.

The Helix system allows exceptionally compact EQ systems to be assembled. For
example, one DN9340 and six DN9344 units would provide 26 channels of EQ, each with graphic,
parametric, and dynamic EQ, plus flexible filters, all in 8U of rackspace.

·

Interface to Midas consoles.

To further enhance the speed of operation of the Helix system, an
interface is provided which connects to Midas Heritage and Legend series consoles. This allows
the EQ system to be controlled automatically from the solo system of the console, ensuring that
the correct EQ device is always ready for instant access.

7

l abc

8

Identification of controls:DN9340

labels the soft key functions. Typically

This area of the main graphic display

these include “select” to choose a

a circular choice of options for that type of

particular filter, and “menu” to step round

new filters (parametric and filter modes

EQ. Additional functions include adding

only) and selecting an individual fader or

filter to be in or out. On the home page

naming and markerfunctions.

these buttons access the gain, delay,

l abc

frequency response of the selected type of

Main graphic display - this shows the

EQ active lights - these show if a

particular type of EQ is currently

page. Along the top edge is the name of

EQ, or the overall response on the home

affecting the overall response. Note that

this is not just an indication of the bypass

status (bypass) of each type of EQ and the

the current working memory, the in/out

state. For example, if all the faders on the

graphic EQ are flat, then the light will not

unit name.

be lit. If the graphic is not bypassed, and

then a fader is moved away from zero, the

light will now light to indicate that the

response is now being affected by the

graphic. This is particularly useful on the

home page where it can be quickly seen

what is contributing to the overall

dynamic and filters. Pressing one of

equalisation; graphic, parametric,

Access keys to control each type of

9

these keys selects the type of EQ to be

controlled. These keys do not affect the

actual sound at all - they just activate the

controls. The large display will change to

and the “type” bypass LED will indicate

show the display for the selected EQ type,

whether this section is bypassed or not.

The keys illuminate to show which type

the HOME(SETUP) key to return to the

of EQ is currently being controlled. Press

system response.

home page, which will show the overall

Identification of controls:DN9340

l abc

Alphanumeric display - this shows

parameter values for the current function

Soft keys for selecting options and

secondary functions. These keys

being controlled by the encoder knobs. In

illuminate to indicate whether they are

labelling is directly above the relevant

general, when setting parameters the

active in aparticular mode ornot.

knob, with the title on the top row and the

value on thebottom row.

When selecting options or entering text,

the top row shows the title and the knob

functions separated by commas, with the

status on thebottom row.

Channel select key. Press to select either

Bypass key - on the home page this

10

channel A or B for control. If the unit is

linked for stereo operation then both

selected channel (both channels if linked).

bypasses the complete unit for the

indicators will be lit and the key will be

inoperative.

bypass operates onthat type ofEQ only.

the keys above the bypass switch), the

When a particular EQ type is selected (by

Identification of controls:DN9340

used for controlling values and selecting

The left, centre and right encoder knobs -

options. Each knob is surrounded by an

that the knobis active inthe current mode.

illuminated blue ring which lights to show

l abc

HOME(SETUP) key. Press once to return

to the home page from any of the

complete unit settings to one of the 64 user

STORE and RECALLkeys. Used to store

individual EQ pages. Once on the home

page, press and hold for one second to

In addition to user memories settings may

memory locations and then to recall them.

access the setup menu. Step through the

be recalled from “preset” memories that

setup menu (and exit after the last item) by

can only be manipulated by means of an

repeatedly pressing this key. The

external computer.

HOME(SETUP) key is also used to abort

from STORE andRECALLoperations.

11

Two part touchstrip. The touchstrip is

and can also be used to adjust gain

used to select individual faders or filters

a particular filter or fader. Press and hold

settings. Press either part briefly to select

or tap repeatedly to increase the level

Note that the lower strip is wider than the

(upper strip) or reduce it (lower strip).

upper and lower strips simultaneously

more urgent to reduce gain... Pressing

upper one to reflect that it is generally

allows the creation of fader groups.

Identification of controls:DN9340

Power switch.

Power ON indication.

Output metering incorporating multi-

point clip indication. These meters

indicate the actual level leaving the unit,

while the red clip light indicates internal

clipping (monitored throughout the

internal processing stages) irrespective of

.

actual output level

dynamic EQ metering. Four

T-DEQ

meters are provided to monitor all four

l abc

dynamic EQ filters.

gain trim.

input level immediately after the input

clip indication. This meter indicates the

Input metering incorporating multi-point

PC port connector, using a three-wire RS-

232 interface on a Mini-DIN connector.

Use with the supplied cable to install

software updates or to control the unit

from an external computer. Note that this

is entirely separate from the rear-panel

RS-232 and RS-485 connectors, and can

be used at the same time as the rear panel

connectors.

12

Connections:DN9340

Audio connectors for

Audio connectors for

channelA.

channel B.

Pin 3 Cold

Pin 2 Hot

with:

Electronically balanced

Pin 3 Cold

Pin 2 Hot

with:

Electronically balanced

l abc

Pin 1 Ground

Pin 1 Ground

consoles.

abc

l

solo operation in association with

RS-232 serial interface for auto

Pin 2 Hot

balanced with:

for input or output. Connectors are

through” fashion, so either may be used

These connectors are connected in“loop

RS-485 serial communications.

Pin 1 Ground

Pin 3 Cold

13

Mains inlet unit is auto

sensing over the range 100-

240VAC.

l abc

14

Signal flow

l abc

METER

OUTPUT

CLIP DETECT

OUT A

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

STEREO LINK

OUTPUT

CLIP DETECT

METER

OUT B

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

METERS

DYNAMIC EQ

INPUT

METER

CLIP DETECT

FILTERS

DELAY

INPUT

LEVEL

IN A

METERS

DYNAMIC EQ

INPUT

METER

CLIP DETECT

FILTERS

DELAY

INPUT

LEVEL

IN B

15

l abc

16

Operation DN9340: Home page

The home page is accessed from any of the EQ pages by pressing the HOME(SETUP) key once. In the setup
menu the HOME(SETUP) key is pressed repeatedly to move through the menus, and after the last menu entry
returns to the home page.

On the home page, the large display shows the overall system response. Along the top edge is the name of the
current working memory, the in/out status (bypass) of each type of EQ and the unit name. The alphanumeric
display shows the unit name and the name of the current working memory. On the home page, the bypass key
will bypass all processing for the selected channel (A, B or both if linked for stereo in the setup menu).

l abc

Home page sub-menus

This menu provides controls for the overall delay of the system and the input gain trim.

The delay is set in increments of 20.83uS (1 sample at 48kHz sample rate) and is displayed in
time units by default.Alternatively the display can be selected to show distance in either Metric
or Imperial units. Details ofchanging the units are found in the Setup menu section on page 27.

The input gain control has a range of -40dB to +12dB in 0.1dB steps, and also provides an “off”

position which mutes the input signal.

Press HOME(SETUP) to return to home page.

17

A/B Link

This menu allows the unit to be linked for stereo operation. Turnthe right-hand encoder to select
linked or non-linked (mono) mode. Note that when linking, the channel
will be copied to the other channel, so that both channels are thenidentical. In other words, if the
“A” lamp is lit over the A/B select switch, then the settings for Channel A will be copied to
Channel B. If the “B” lamp is lit, the settings for Channel B will be copied to ChannelA.

Touchstrip Operation on the Home Page

In the home page, the touchstrip is inoperative. In the Marker sub-menu, the touchstrip can
be used to select which marker is currently active, and to drag the active marker to a new
frequency.

l abc

currently displayed

18

Operation DN9340: Graphic equalisation

Select graphic equalisation by pressing the GRAPHIC key.

The default display for the graphic EQ is 31 faders indicating the gain of the 31 bands of the 1/3 octave
equaliser. The left encoder can be used to select a fader and then the right-hand encoder can be used to set the
gain for that fader. Alternatively the fader can be selected using the upper or lower section of the touch strip.
If the touch strip is pressed for longer than half a second then the selected fader will move up (upper strip) or
down (lower strip) until the touchstrip is released.

Soft Key Functions

selects each fader in turn

steps through the following pages on the alphanumeric display. After the

last page, the next press returns to the first page, and so on.

l abc

o

Default page shows frequency andlevel for the currently-selected fader

EQ mode page

o

·

EQ type - allows the selection of different EQ characteristics. Proportional,
Constant and Symmetrical-Q types are available, together with emulations of the
classic Klark Teknik DN360 and DN27. See the application notes later in this
manual for more detail on selecting EQ types and Q. If in doubt, select either
DN27 or DN360 emulation for sensible curves with minimum fuss…

·

Q - only available with Proportional, Constant and Symmetrical-Q types. This
should be adjusted with care, as it is possible to produce both large amounts of
overlap between bands and also narrow filters with large inter-band ripple. The
default position for normal 1/3 octave operation is clearly indicated on the display.

·

Graph Mode - this toggles the large graphic display between the fader displayand
a frequency response curve.

Automatic features page

o

19

l abc

·

Auto Gain - this feature, originally introduced on the Klark Teknik DN3600

equaliser, automatically adjusts the system gain so that the overall program level
remains constant despite changes in equalisation. The left encoder enables or
disables this feature. If set to “No” then the graphic EQ gain trim (operated by the
centre encoder) is entirely manual in operation. If set to “Yes”, then as the graphic
EQ faders are moved, the gain trim will automatically be adjusted to compensate
for the overall (average) level change. At any time, the display over the centre
encoder will show the actual gain trim being applied, and this can always be
adjusted manually (even whenAuto EQ is active).

Auto-EQ - this section enables automatic room equalisation when the Helix unit

·

is used with a Klark Teknik DN6000 Real Time Analyser. This function is only
available when the optional DN6000 interface is fitted.

After the Auto-EQ function is selected by setting the menu option in the
Automatic Features menu page, the user will be prompted to confirm that the
graphic EQ response will be set to a 1/3 octave symmetrical response (Q = 7.8) if
this has not already been set, as this is the only response that will match that of the
filtering in the DN6000. If 'No' is selected then the user is returned to the
Automatic Features menu page without the Auto-EQ function being enabled. If
'Yes' is selected then the Auto-EQ function is enabled, and the graphic EQ
response is changed to the 1/3 octave response, the user is then returned to the
Automatic Features page. Additionally, the third soft key from the top will now
be labelled 'AutoEq' to allow a snapshot of the DN6000's audio spectrum
frequency domain measurement to be captured by the Helix unit when this key is
pressed. The Helix unit will then generate a reciprocal response curve to
compensate for any peaks or troughs in the DN6000's measurement in order to
create a flat response across the audio spectrum.

In remote control applications, any slave unit can have the audio spectrum
snapshots captured from a DN6000 connected to the master unit applied to it. A
slave DN9340 cannot however capture snapshots from a DN6000 connected
directly to it.

EQ - Flat page

o

This page allow the graphic EQ faders to be quickly reset to their unity gain position.
To flatten the response, turn the centre encoder clockwise, then turn the right encoder
clockwise to confirm. Pressing anyother key will abort the sequence.

pressing this allows an individual fader insert or a selected block of

faders to be switched in and out of circuit.

20

Touchstrip operationwith Graphic equalisation

On the Graphic EQ page, the touchstrip can be used as an alternative to the encoder knobs for
selecting and operating the faders on the display. Touch either the upper or lower part of the
touchstrip below the fader that you want to select. The fader will highlight to indicate the
selection. Tapping repeatedly at the same position will result in the fader moving up (upper
strip) or down (lower strip) in 0.5dB increments. Pressing the strip continuously in the same
place will result in the fader ramping upor down over itsfull range. As an aidto resetting faders
to exactly 0dB, this ramping motion will stop as the fader passes overthe 0dB position. Release
the strip and then press again to continue moving past this point.

Grouping

l abc

Simultaneous touch in both parts of the strip

Groups of faders can be created and moved together. This is achieved by pressing below one
fader on the upper strip, and below a different fader on the lower strip. A group will be created
including all faders between those two that have been selected. This can now be moved up and
down using the encoder knob or by using the touchstrip in the area below the group. Pressing
the touchstrip outside the range of the group or moving the “frequency” encoder knob will
disband the group.

21

Operation DN9340: Parametric equalisation

Select parametric equalisation by pressing the PARAMETRIC key.

The display for the parametric equaliser is similar to the home page, showing the frequency response - in this
case just for the parametric sections. At the top right is a legend “PEQ 1 of 1” which indicates which PEQ
section is currently active for control, and also how many sections are in use. So, for example, if we have 4
sections in use, and are adjusting the second one the legend would read “PEQ 2 of 4”. If no PEQ sections are
active, then the display is blank except for the “ADD” key.Press this key to add a section of EQ.

Soft Key Functions

selects which PEQ section is to be controlled

o

Default page displays frequency, Q andlevel for this section

l abc

EQ settings page

o

EQ type - this allows control over the characteristics of the equaliser.

·

Proportional, Constant, and Symmetrical curves are available.

Graph display - three modes are available, to ensure that clear information is

·

available for any application. “Curve” mode shows the overall response of the
whole parametric equaliser. “Active” mode shows just the response of the single
section currently being selected for adjustment. “Individual” mode shows all the
sections, but as individual curves rather than as a single composite response.

EQ remove page

o

This page allows the currently-selected PEQ section to be deleted entirely (as opposed
to bypassed see IN/OUTbelow). The centre encoder is turned clockwise to remove the
section, and then the right encoder is also turned clockwise to confirm.

adds a new PEQ section. There are 12 PEQ sections available to each

channel, each of which can be used across the whole frequency range from 20Hz-20kHz.

pressing this allows an individual section to be switched in and out of

circuit without clearing its settings.

22

Touchstrip operationwith Parametric equalisation

On the Parametric EQ page, the touchstrip can be used to select the currently-active section of
EQ. This is achieved by pressing either the upper or lower part of the strip below the centre
frequency of the chosen section. The centre frequency will highlight to indicate the selection.
Once selected, the frequency of the EQ section can be “dragged” up and down the display by
pressing the strip and sliding the point of contact to left and right. There is no difference
between the upper and lower strips when in Parametric mode.

l abc

23

Operation DN9340: Dynamic equalisation

T-DEQ

l abc

Select dynamic equalisation by pressing the DYNAMIC key.

The display for the parametric equaliser is similar to the home page, showing the frequency response of the
two dynamic EQ sections. Note, however, that for each of the two sections there are two different

T-DEQ

curves drawn. These correspond to the response curve at high signal level and low signal level respectively.
For more details on dynamic equalisation see the application notes later .

on page 31

Soft Key Functions

this switches the controls between the two dynamic EQ sections

Default page shows frequency andQ/slope for this section.

o

Each of the sections can be used over the whole frequency range from 20Hz to 20kHz,
and has fully parametric control over Q. In addition, each section can be selected to be
a high or low shelf, with 6dB/octave or 12dB/octave slopes. This is selected by turning
the Q knob beyond its maximum value of 20.

Lo Threshold /Level page

o

This page contains the settings for the low threshold (the signal level that we want to
call “quiet”) and the amount of cut or boost that we want at that “quiet” signal level.

Hi Threshold /Level page

o

This page contains the settings for the high threshold (the signal level that we want to

call “loud”) and the amount of cut or boost that we want at that “loud” signal level.

24

l abc

o

Time constants page

This page allows the attack and release time constants to be set - in other words how
quickly the unit will respondto a sudden increase inlevel (attack) ora suddendecrease
in level (release).

EQ settings page

o

·

EQ type - this allows control over the characteristics of the equaliser.

Proportional, Constant, and Symmetrical curves are available.

·

Graph display - two modes are available, to ensure that clear information is

available for any application. “Both” mode shows the overall response of the
whole dynamic equaliser. “Active” mode shows just the response of the single
section currently being selected for adjustment

pressing this allows an individual section to be switched in and out of

circuit.

Touchstrip operationwith Dynamic equalisation

On the Dynamic EQ page, the touchstrip can be used to select the currently-active section of
EQ. This is achieved by pressing either the upper or lower part of the strip below the centre
frequency of the chosen section. The centre frequency will highlight to indicate the selection.
Once selected, the frequency of the EQ section can be “dragged” up and down the display by
pressing the strip and sliding the point of contact to left and right. There is no difference
between the upper and lower strips when in Dynamic mode.

25

Operation DN9340: Filters

Select filters by pressing the FILTERS key.

The display for the filtersis similar to the homepage, showing the frequency response- in this case justfor the
filters.At the top right is alegend “Filter 1 of 1”which indicates which filter iscurrently active for control, and
also how many filters are in use. So, for example, if we have 3 filters in use, and are adjusting the second one
the legend would read “Filter 2 of 3”. If no filters are active, then the display is blank except for the “ADD”
key. Press this keyto add a filter.

“Create Filter” function

l abc

Turn the left encoder to select the type of filter required. The available options are Notch,

Low-pass (normal and peaking), High-pass (normal and peaking), Hi shelf and Lo shelf.
Turn the right encoder to confirm the selection and create the filter.

Soft Key Functions

selects which filter is to be controlled

Default page displays the main parameter controls for each filter.

o

The controls available vary depending on the type of filter selected:

Filter Type Left Centre Right

Notch Frequency Q ­Low Pass (LPF) Frequency Normal/Peaking Slope/Gain
High Pass (HPF) Frequency Normal/Peaking Slope/Gain
Hi Shelf Frequency Slope Level
Lo Shelf Frequency Slope Level

26

Filter settings page

o

·

Filter type - available types are Notch, Low Pass (normal and peaking), High Pass
(normal and peaking), Hi Shelf and Lo shelf.

·

Graph display - three modes are available, to ensure that clear information is
available for any application. “Curve” mode shows the overall response of the
whole filter module. “Active” mode shows just the response of the single filter
currently being selected for adjustment. “Individual” mode shows all the filters,
but as individual curves rather than as a single composite response.

Filter remove page

o

l abc

This page allows the currently-selected filter to be deleted entirely (as opposed to
bypassed - see IN/OUT below). The centre encoder is turned clockwise to remove the
filter,and then the right encoder is also turned clockwise to confirm.

adds a new filter.

Turn the left encoder to select the type of filter required. The available options are

Notch, Low-pass (normal and peaking), High-pass (normal and peaking), Hi shelf
and Lo shelf. Turn the right encoder to confirm theselection and createthe filter. There
are 4 filters available to each channel, each of which can be used across the whole
frequency range from 20Hz-20kHz.

pressing this allows an individual filter to be switched in and out of

circuit.

Touchstrip operationwith Filters

On the Filters page, the touchstrip can be used to select the currently-active filter. This is
achieved by pressing either the upper or lowerpart of the strip belowthe centre frequency of the
chosen filter. The centre frequency will highlight to indicate the selection. Once selected, the
frequency of the filter can be “dragged” up and down the display by pressing the strip and
sliding the point of contactto left andright. There is no difference between the upper andlower
strips when in Filter mode.

27

Operation DN9340: Storing and recalling settings

The Helix unit includes two types of memory location, to provide maximum flexibility in a range of
applications. There are 64 user memories in battery-backed-up SRAM, and also 32 preset memories in non­volatile FLASH memory. Recalling settings from either memory type uses the same procedure, and the user
memories can be stored directly from the front panel of the unit.The FLASH memories, however, can only be
programmed directly from an external computer. This provides an absolute safeguard for valuable system
settings, particularly in fixed installations.

o

Storingsettings:

·

Turn left encoder knob to select the destination (U1 to U64)

·

Press STORE again toconfirm (or HOME(SETUP) to abort)

Press STORE

l abc

·

Use the centre encoder knob to select characters, and the left one to move left
and right, to enter a suitable name for the memory. Alternatively, if the name
already there indicates that you do not want to overwrite it, then
HOME(SETUP) will abort the store operation as before.

·

Press STORE again toconfirm. This will return you to the home page.

o

Recalling settings:

·

Turn the left encoder to select the user (SRAM) memory required, or the right

encoder to select a preset (FLASH) memory.

·

Press RECALL again to confirm. This will return you to the home page.

Press RECALL

28

Operation DN9340: Setup menu

The Setup menu provides access to the options and configuration settings for the unit. It is accessed by first
selecting the HOME(SETUP) key to go to the home page, then pressing andholding theHOME(SETUP) key
for one second. Each press of the HOME(SETUP) key will then move on to the next item in the Setup menu.
After the final item, the unit returns to the home page.

Setup Menu items

Communications channel

·

This selects the communications address for the unit when using remote control. See
the remote control section for more information on using remote control. Select
“OFF” for local control.

l abc

·

Panel lock .
character password. The left encoder is used to move between the eight characters of
the password, and the centre encoder is then used to select which letter appears in each
character position. When the correct password has been selected, turn the right
encoder to select “Locked”, “Locked with Recall”, or “Unlocked”. Locked will
disable all front panel controls except the HOME(SETUP) key. Locked with Recall
allows the RECALL key to be used to recall stored memories, but the user is prevented
from editing any settings. In order to unlock a locked unit, press HOME(SETUP)
once, then press and hold HOME(SETUP) for one second to enter the Setup menu.
Press HOME(SETUP) once more tomove past theCommunications page. Use the left
encoder to move between the eight characters of the password, and the centre encoder
to select which letter appears in each character position. Finally turn the right encoder
to confirm the password entry. Press HOME(SETUP) to return to the home page.

·

LCD contrast adjustment. To ensure optimum screen visibility in a range of lighting
conditions, it is possible to individually adjust the contrast of the two LCD displays.
“Alpha” adjusts the contrast of the alphanumeric display, “Graphic” adjusts the
contrast of the large graphic display, and “INV” allows the mode of the graphic LCD to
be switched between white-on-blue to blue-on-white.

·

Name unit. This allows the unit to be given a name - useful in systems that contain
several Helix units.The left encoder knob is used to move between characters, and the
right one to select the character required in a given position.

This allows the front panel controls to be locked by means of an eight-

·

Name Memory. This allows the working memory to be named. Note that a recall
operation will overwrite this with the name of the recalled memory.

·

Delay units. The equaliser can be set to display delay settings either directly in time, or
expressed as distance in metric or imperial units. The left encoder knob selects the
units, and the centre one allows the user to enter an ambient temperature value, which
is used in the distance calculations to improve accuracy.

·

Power-on Logo. The equaliser normally shows a logo page at power-on, including
information such as softwareversion number. This canbe disabledby selecting“Logo
OFF”.

29

Operation DN9340: Metering

Comprehensive audio metering is provided by eight LED bargraph meters.

There are a pair of input meters (labelled A and B for audio channels A and B respectively),
which show the input level immediately following the input gain control. These can therefore
be used as a guide for setting the input gain to match the signal level being sent to the unit.
With the input gain control set to 0dB (unity gain) then full-scale on the meter will occur at a
signal level of +21dBu (which is the maximum permissible signal level). The input meters
incorporate a red ‘clip’ LED that indicates signal clipping both on the actual input to the unit
and also after the gain control - this ensures that all possible clip conditions are monitored
irrespective of the setting of the gain control.

l abc

There are a pair of output meters (labelled A and B for audio channels A and B respectively),
which show the output level from the unit. Full-scale on the meter indicates maximum output
from the unit, which corresponds to +21dBu. The output meters also incorporate a red ‘clip’
LED. This indicates signal clipping within the unit, and is monitored at all internal points
where gain can be applied. Thus, if a large amount of gain is added with one section of a
parametric EQ resulting in a clipped signal, but the level is then reduced by a subsequent EQ
section, the clip LED will still light to indicate the internal clip condition despite the
apparently safe output level. In this situation the input gain should be reduced to provide
sufficient headroom for the desired EQ characteristic. Note that because these meters are on
the output of the unit, they will show the effect of any delay that has been selected.

There are four meters which show the action of the dual - threshold dynamic EQ

T-DEQ

system - one meter for each EQ section on each of the two audio channels A and B. The
dynamic EQ meters are calibrated in percentage terms, from 0 to 100. If no dynamic EQ is
selected, or if the signal is below the ‘low’ threshold, then the meters will show 0% (i.e. no
LEDs lit). Under this condition the dynamic EQ will be using the ‘low’ frequency response
settings. If the signal level is above the ‘high’ threshold, the relevant meter will indicate 100%
(fully lit) showing that the ‘high’EQ settings are now being applied. If the signal is between
the two thresholds, then the EQ will be morphing between the two EQ settings, and the meter
indicates the signal level relative to the two thresholds. Note that the effect of the attack and
release controls is also indicated on these meters - the height of the bar indicates the actual EQ
being applied, so if a slow release is set, for example, you will see the meter drop back slowly
following a peak.

30

Operation DN9340: Clear down sequence

Because of the comprehensive facilities available on the DN9340, it maybe important to ensure that the unitis
“cleared down” before use. Remember to clear down both channelsA and B if the unit is not linked for stereo
operation. There are a number of possible strategies for this:

A. Recall a memory that contains a suitable set of default values.

B. Select each type of EQ, and bypassthem in turn by pressing “GRAPHIC”,then “BYPASS” (the

TYPE bypass lamp lights), “PARAMETRIC”, then BYPASS, and so on for DYNAMIC and
FILTERS. Finally select HOME, press thesoft key labelled “Delay/Gain” and set thedelay and
gain to zero values. Press HOME again, and the unit is ready to use and set to provide a flat
response. This method is fast, but has the disadvantage that when the BYPASS function is
deselected for a given type of EQ, the previous settings will be restored, which may not be what
is required.

C. To ensure that each type of EQ is zeroed-out and can be introduced seamlessly into circuit,

follow this sequence:

l abc

·

Press HOME, then select the soft key labelled “Delay/Gain”. Set delayand gain to zero.

·

Press GRAPHIC. Press the soft key labelled “Menu” three timesto display the “EQ FLAT”
menu page. Turn the centre encoder clockwise, then the right encoder clockwise to
confirm.

·

Press PARAMETRIC. If parametric EQ sections exist, then press the soft key labelled
“Menu” twice to display the “Remove” menu page. Turn the centre encoder clockwise,
then the right encoder clockwise to confirm deletion of the selected parametric section.
Repeat these encoder moves until no sections of EQ remain.

·

Press DYNAMIC. Press the soft key labelled “Menu” to display the Lo settings page. Set
the Lo Level to 0dB. Press the soft key labelled “Select” to jump to the other section of
dynamic EQ. Set the Lo Level to 0dB. Now press “Menu” once to display the Hi settings
page. Set the Hi Level to 0dB. Press “Select” to jump back to the first EQ section. Set the
final Hi Level to 0dB.

·

Press FILTERS. If filter sections exist, then press the soft key labelled “Menu” twice to

display the “Remove” menu page. Turn the centre encoder clockwise, then the right
encoder clockwise to confirm deletion of the selected filter section. Repeat these encoder
moves until no filters remain.

·

Press HOME to return to the home page.

31

Remote Control: The Basics

Connections

A DN9340 master unit can control both DN9340 and DN9344 units as slaves. In order to set up a remote
controlled Helix system, first connect the units together using the RS-485 connectors on the rear panel. The
units are connected in sequence from output to input, in any order. The first unit in the chain will have no
connection to its input, and the last unit will have no connection to its output.

Addresses

The RS-485 network uses a system of addresses to identify which unit is being controlled. The Helix system
supports addresses from 1 to 32. A DN9340 unit has one address and a DN9344 has two addresses,
corresponding to the left-hand pair of channels (Section 1) and the right-hand pair of channels (Section 2)
respectively. The reason for having two addresses to communicate with each DN9344 is to allow systems to
be built up from eitherDN9340 (2 audio channels) orDN9344 (4 audiochannels) in any combination. At any
time, two DN9340s can be replaced by a single DN9344 (or vice versa) without any need to change the
addressing of the system.

Data model

l abc

Each Helix unit has a “ ”which is the current state of theunit as seen on the frontpanel - this
also corresponds to the sound that is currently being heard. In addition, there are 32 user and 32 preset
memories in each DN9340 and in each pair of channels in a DN9344.

Issuing a “ ” command to a unit will copy the working memory into the selected user memory on
that unit.

Issuing a “ ” command will copy the selected user or preset memory into the working memory
on that unit.

When using remote control, the Master unit holds a local copy of the working memory for slave that is
connected. This allows fast switching between units being controlled. When the system is set on-line, the
user can choose whether to “Get all” data from the slaves or to “Set all” data from the master. This allows the
settings for up to 64 channels of audio to be stored in a single DN9340, or conversely an “empty” master
DN9340 can be connected to a system that is already running and upload the system data.

Getting started

Connect the units using the RS-485 ports as described above. Set the comms address for each slave unit ­ignore the master unit for now. It doesn't matter what addresses you use, but each unit MUST have a unique
address (two unique addresses for a DN9344).

working memory

store

recall

each

On a DN9340:

show that it is active. Turn to select the channel number. Turn the centre encoder to select SLAVE
mode. Press HOME(SETUP) toconfirm.

On a DN9344:

channel number for Section 1. Repeat for Section 2. Press SETUP to confirm (unit will display
password menu). Press SETUP to exit.

Press HOME(SETUP). Press and hold HOME(SETUP). The left encoder lights, to

Press SETUP. Press and hold SETUP. Use the UP and DOWN buttons to select the

32

Remote Control

Once all the slaves have been set up, the master unit can be set on-line. Again, it must have a communication
channel allocated, which must not be the same as any of the slaves.

Press HOME(SETUP). Press and hold HOME(SETUP). The left encoder lights, to show that it is
active. Turn to select the channel number for the master unit. Turn the centre encoder to select
MASTER mode. Turn the right encoder to select the maximum number of audio channels in the
system. Press HOME(SETUP) toconfirm.

The reason for setting the maximumnumber of audiochannels is toprevent the masterunit from wastingtime
looking for units that are not present and trying to set them on-line, whilst allowing the user to choose any
channel addresses that are convenient. For example, a system including two DN9340s and two DN9344s
will have 12 audio channels, so set the “Max” value to 12. When the master unit goes on-line, it will search
for units starting from address 1. Once itfinds the correct number of audio channels, it will stop searching.

The unit will now ask the user to choose either to “Set All” slaves to the data contained in the master
unit (from the master unit's local copy of the slave data for each address) or to “Get All” data from the
slaves themselves. Press HOME(SETUP) to confirm. The unit will show a “DETECTING UNITS”
page as it searches and initialises the slaves. The system is now on-line.

l abc

Operation

To select slaves, go to the home page by pressing HOME(SETUP). Press the lowest of the four soft keys
labelled “Comms”. This shows a set of “buttons” on the large graphic screen which correspond to each audio
channel in the system. Use the touchstrip to select the channel that is to be controlled. Units above the line
are selected using the upper touchstrip and units below the lineusing the lower touchstrip.

The A/B SELECT key can also be used to move between slave channels in the same way as for normal
DN9340 operation.

Pressing and holding the A/B SELECT key provides a fast shortcut to the Comms page from any of the EQ
pages (graphic, parametric etc). If this method is used to access the Comms page, then the master unit will
remember which EQ page was in use when that slave is next selected for use.

System naming

To ensure clarity of operation, each slave can be assigned a meaningful name, in addition to its channel name
(1A, 3B etc.). Toset up the names, first select the Comms page on the master unit. Now press the second soft
key (labelled “System”). This opens the system configuration page.

Ahighlighted area shows the field that is currently being edited.
The left-hand encoder scrolls up and down the list of units.
The touchstrip is used to select the column to be edited.

33

Remote Control

The following name fields can be edited:

l abc

Long name:

which of the slaves is being controlled. It is also displayed on any DN9340 units which are
being used as slaves. The first nine characters are not editable, and show the channel number.
The last eleven characters are editable by the user.

Name:

the system.

Once all the assignments have been made, press “Confirm” to return to the Comms page.

Auto-solo operation

Instead of selecting slaves manually from the master unit, the Helix system can be controlled from the solo
system of Midas Heritage and Legend consoles. The console RS-232 port is connected to the RS-232
connector (D9) on the rear of the master DN9340 unit using a straight-wired cable (no crossovers). Once the
channel assignments have been configured (see below) then pressing a solo button on the console will
automatically select the channel of EQ that corresponds to that console function onto the master unit, ready to
be controlled. To set up the assignment,first select the Comms page on the master unit. Now press the second
soft key (labelled “System”). This opens the system configuration page.

Ahighlighted area shows the field that is currently being edited.
The left-hand encoder scrolls up and down the list of units.
The touchstrip is used to select the column to be edited.

This 20-character name will be used on the master unit to indicate to the user

This 3-character name will be used on the front-panel displaysof any DN9344 units in

The following fields can be edited:

Autosolo:

Midas Heritage or Legend console. The available functions are: None, Input, Group, Aux,
Matrix, Solo Clear.

Chan:

So, for example, if slave EQ channel 1A is configured withAutosolo set to Group and Chan to 5, then
pressing group solo 5 on the console will select slave EQ channel 1A onto the master Helix unit for
control.

Once all the assignments have been made, press “Confirm” to return to the Comms page.

Copy channel function

It is possible to copy a whole audio channel's settings to another channel or to multiple channels. Note that
mono channels can only be copied to other mono channels, and stereo linked channels can only be copied to
other stereo linked channels.

On the Master unit's Comms page, press the softkey labelled “Copy Mon” (tocopy mono channels) or
the soft key labelled “Copy St” (to copy stereo channels).

This allows each audio channel to be associated with a type of solo function on the

This selects the particular channel solo that will be used for that channel of EQ.

Use the touchstrip to select the channel that you wish to copy from. Note that only channels of the
selected type (mono or stereo) are shown.

Press the soft key labelled “Confirm” to select the source channel.

34

Remote Control

Now, the possible destination channels are shown. Use the touchstrip to select one or more channels
to copy to. Once all the destination channels are selected, press the soft key labelled “Confirm”. The
unit will display an “are you sure” message, and a final press of the “Confirm” soft key will start the
copying process.

At any time, the copy can be aborted by pressing the Home key.

l abc

35

l abc

36

Identification of controls:DN9344

Power switch

Power on indicator

Section 2 output metering

incorporating multi-point clip

indication. This meter indicates the

actual output level from the unit, while

the red clip light indicates internal

T-DEQ

clipping, which is monitored at every

internal processing stage.

l abc

Section 2 input metering

incorporating multi-point clip

indication. This meter indicates the

level immediately after the input gain

for remote control, and to enable contact

select communications channel (address)

SETUP menu. The setup menu is used to

SETUP key. Press and hold to enter

trim.

TWO DN9340 master units. The

Section 2) as it contains the equivalent of

channels (one for Section 1 and one for

has TWO independent communications

closure operation. Note that each DN9344

Section 2 dynamic EQ

Communications Mode display will flash,

metering. Four separate meters are

monitoring of all dynamic EQ

provided, to allow continuous

of the SETUP key will toggle between the

UP and DOWN keys. A momentary press

indicating that it can be changed using the

sections.

Communications Mode (which will not

display of Last Memory Recalled and the

display of the electronic scribble-strips and

flash indicating thatit cannot bechanged).

The large red alphanumeric displays can be

used to show electronic scribble-strip

information, Last Memory Recalled, and

Communications Mode. In remote control

mode, the displays show a 3-character

name for each audio channel. This name is

set from the master unit. In relay (contact

closure) mode or stand-alone mode the

37

displays show Last Recalled Memory and

Communications Mode.

Identification of controls:DN9344

UP and DOWN keys for Section 2.

Used to select communications

channel (address) for remote control

and also contact closure mode.

Active only when in SETUP menu

(press and hold SETUP to enter this

l abc

menu).

Display mode indicator (blue) for

Section 2. When lit this indicates that

the large red displays are nowshowing

Last Memory Recalled and

Communications Mode. When not lit,

Section 1 output metering

the displays are showing electronic

scribble-strip names. In this case the

left-hand three characters show the

incorporating multi-point clip

indication. This meter indicates the

actual output level from the unit, while

name of ChannelA and the right-hand

three the name of Channel B, for each

of the twosections.

the red clip light indicates internal

clipping, which is monitored at every

internal processing stage.

T-DEQ

Remote ControlActive indicator (green) for Channel 1A, 1B,2Aand 2B. This shows that the master unit is currently

controlling this channelby remote control. These green lamps areoften referred toas the “me” lights.

Section 1 input metering

incorporating multi-point clip

indication. This meter indicates the

level immediately after the input gain

trim.

38

Section 1 dynamic EQ

metering. Four separate meters are

sections.

monitoring of all dynamic EQ

provided, to allow continuous

Identification of controls:DN9344

l abc

Communications traffic indicators.

These indicate when there is activity

on any of the external interfaces.

updates or to control the unit from an

supplied cable to install software

PC port connector. Use with the

Transmit and receive data are shown

for front panel (RS-232) and rear panel

entirely separate from the rear panel

external computer. This connector is

(RS-485) data, and also the contact

closure (RELAY)input.

the same timeas the rearpanel ports.

RS-485 connectors, and can be used at

UP and DOWN keys for Section 1.

Used to select communications

channel (address) for remote control

and also contact closure mode.

Active only when in SETUP menu

(press and hold SETUP to enter this

menu).

Scribble-strip areas to allow easy

labelling of the unit. Use only

permanently marking the unit.

chinagraph pencils to avoid

Remove chinagraph markings by

wiping with a soft cloth. Do not use

39

surface.

solvents as these may damage the

Connections:DN9344

Pin 3 Cold

Pin 2 Hot

balanced with:

Electronically

channel 1A.

Audio connectors for

Pin 3 Cold

Pin 2 Hot

balanced with:

Electronically

channel 1 B.

Audio connectors for

l abc

Pin 1 Ground

Pin 1 Ground

Pin 3 Cold

Pin 2 Hot

balanced with:

Electronically

channel 2A.

Audio connectors for

Pin 3 Cold

Pin 2 Hot

balanced with:

Electronically

channel 2 B.

Audio connectors for

either may be used for

through” fashion, so

connected in “loop

These connectors are

communications.

RS-485 serial

Pin 1 Ground

Pin 1 Ground

balanced with:

Connectors are

input or output.

Pin 2 Hot

Pin 1 Ground

Pin 3 Cold

contact closure to recall memories on the unit. Pin

Contact Closure (RELAY) interface. This allows a simple

connections are asfollows:

Pin 1 -recall Preset /User 1 on Section1 (the left-handunit)

Preset / User

Pin 2 -recall 2 on Section1 (the left-handunit)

Preset / User

Pin 3 -recall 3 on Section1 (the left-handunit)

Preset / User

Pin 4 -recall 4 on Section1 (the left-handunit)

Preset / User

Pin 5 -recall 1 on Section2 (the right-handunit)

Preset / User

Pin 6 -recall 2 on Section2 (the right-handunit)

Preset / User

Pin 7 -recall 3 on Section2 (the right-handunit)

Preset / User

Pin 9 -common

Pin 8 -recall 4 on Section2 (the right-handunit)

to perform arecall.

Momentarily connect pin 9 to the appropriate other pin (1-8)

Mains inlet unit is auto

sensing over the range 100-

240VAC.

40

Signal flow

l abc

OUTPUT

CLIP DETECT

DYNAMIC EQ

METER

METERS

OUT 1A

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

FILTERS

STEREO LINK

OUTPUT

ETECT

CLIP D

DYNAMIC EQ

METER

METERS

OUT 1B

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

FILTERS

OUTPUT

CLIP DETECT

DYNAMIC EQ

METER

METERS

OUT 2A

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

FILTERS

STEREO LINK

OUTPUT

ETECT

CLIP D

DYNAMIC EQ

METER

METERS

OUT 2B

EQ

GRAPHIC

EQ

PARAMETRIC

EQ

DYNAMIC

FILTERS

INPUT

CLIP DETECT

METER

DELAY

INPUT

LEVEL

IN 1A

INPUT

CLIP DETECT

METER

DELAY

INPUT

LEVEL

IN 1B

INPUT

CLIP DETECT

METER

DELAY

INPUT

LEVEL

IN 2A

INPUT

CLIP DETECT

METER

DELAY

INPUT

LEVEL

IN 2B

41

Operation DN9344: Remote control mode

This section describes setting up the DN9344 for remote control operation. Please refer to the DN9340
remote control section (on page 32) for information on controlling the system once it is set up.

Press and hold the SETUP button to enter the SETUP menu. Note that the red alphanumeric
displays are now showing Last Recalled Memory and Communication (COMMS) mode. The
blue display mode indicator lights to emphasise this fact. The UP and DOWN buttons light to
show that they are now active.

Press UP and DOWN on the left-hand half of the unit (Section 1) to select the desired
communications channel. There are 32 possible channels available. Each unit (including the
master) MUST have aunique channel number or the system will not work correctly.

Now press the UP and DOWN buttons on the right-hand half of the unit to select its own,
independent communications channel. The reason for having two separate channel numbers
within one unit is that the DN9344 is seen by the system management software as representing
two individual DN9340 units, each with two channels. This allows DN9340 andDN9344 units
to be freely swapped in and out of the system without changing the mapping between audio
channels and communications channels. In other words, every stereo pair of audio channels
has a communications address, irrespective of whether it is a DN9340 or half a DN9344.

l abc

Press SETUP to confirm (unit will display password menu). Press SETUP to exit.

The red alphanumeric displays are now showing the three-character name for each audio
channel. These are set from the master unit. If no names have been entered, the display will
show “---”

42

Operation DN9344: Contact Closure (RELAY) mode

This section describes setting up the DN9344 for relay operation. This allows memories to be recalled using a
simple contact closure mechanism.

Press and hold the SETUP button to enter the SETUP menu. Note that the red alphanumeric
displays are now showing Last Recalled Memory and Communication (COMMS) mode. The
blue display mode indicator lights to emphasise this fact. The UP and DOWN buttons light to
show that they are now active.

Use the UP and DOWN keys to select either “RLP” or “RLU” for preset or usermemory recall
modes.

Note that the left-hand (Section 1) and right-hand (Section2) parts of the unitare entirely
independent. It is possible to use either RELAY mode on Section 1 while Section 2 is
operating in remote control mode, or vice versa. Equally, both sections can operate in
either RELAY mode if desired.

l abc

Press SETUP to confirm (unit will display password menu). Press SETUP to exit.

Memory recalls are now performedby an externalswitch or relay which momentarilyconnects
pin 9 of the RELAYconnector to one of the other pins.

Function assignments are as follows:
Pin 1 - recall 1 on Section 1 (the left-hand unit)
Pin 2 - recall 2 on Section 1 (the left-hand unit)
Pin 3 - recall 3 on Section 1 (the left-hand unit)
Pin 4 - recall 4 on Section 1 (the left-hand unit)
Pin 5 - recall 1 on Section 2 (the right-hand unit)
Pin 6 - recall 2 on Section 2 (the right-hand unit)
Pin 7 - recall 3 on Section 2 (the right-hand unit)
Pin 8 - recall 4 on Section 2 (the right-hand unit)
Pin 9 - common

Preset / User
Preset / User
Preset / User
Preset / User
Preset / User
Preset / User
Preset / User
Preset / User

Momentarily connect pin 9 to the appropriate other pin (1-8) to perform a recall.

43

Operation DN9344: Stand alone mode

To prevent any changes to the settings in the unit, set the Communications Mode to OFF.

Press and hold the SETUP key to enter the SETUP menu.
Use the UP and DOWN keys to select OFF for each section ofthe unit.
Press SETUP to confirm (unit will display password menu). Press SETUP to exit.

l abc

44

Application notes

l abc

Application note 1: Dynamic EQ

T-DEQ

Over the years a number of professional audio products have provided dynamic equalisation functions of
various types. What all these systems have in common is that the frequency response of the device varies
depending on the signal level. Many units are based on compressor / expander technology with frequency
selection, and the controls often resemble those of a dynamics processor.

The system developed by the Klark Teknik research and development team for the Helix series is rather
different. It draws on KT's unrivalled experience in equalisation, and uses the signal level to directly control
parametric equalisers. This purely EQ-based solution allows simple controls that directly relate to the signal
levels. As a result, it is very easy to set the point at which the dynamic EQ starts to operate, and also to set
precisely its maximum effect. We refer to this technique as “Threshold Dependent Equalisation”.

In order to understand the operation, let us first consider a conventional parametric EQ section (Figure 1).
The three controls available to us are frequency, Q (or bandwidth), and the amount of cut or boost.

Figure 1  standard parametric EQ 04/12/02 11:05:08

+20

+10

+0

d

-10

B
u

-20

-30

-40

10 20k20 50 100 200 500 1k 2k 5k 10k

Hz

This shows a series of responses for the parametric EQ with different input levels. As expected, there is no
change in the shape of the curve with different input levels. If the input is 10dB louder, the output is 10dB
louder at every frequency.

45

l abc

If we now replace the parametric with a Helix equaliser and select the dynamic EQ, we have some additional
controls. Frequency and Q controls are as before, but now we have two pairs of controls replacing the single
cut and boost control; these are [low threshold] / [low level], and [high threshold] / [high level]. If we set the
frequency and Q controlsto thearea that we wish to control, then the processor will monitor the signal level in
that frequency range. If the signal level in this part of the spectrum is below the [low threshold] setting, then
the unit considers this a ‘quiet’ signal. The EQ applied to the signal will be controlled by the [low level]
control. If the signal level is above the [high threshold] level, then the unit considers this a ‘loud’ signal, and
will apply the amount of EQ set by the [high level] control. If the signal level is between the two thresholds,
then the equaliser will seamlesslymorph between the two equalisersettings in real time. Manual control over
attack and release times is available to set the speed of response to suit the application.

As an example, consider Figure 2, which shows the Helix applying a boost at low signal levels which is
automatically ‘wound out’at high level.

Figure 2  Helix with boost at low signal level 04/12/02 10:08:20

+15

+10

+5

+0

-5

d

-10

B

-15

u

-20

-25

-30

-35

-40
10 20k20 50 100 200 500 1k 2k 5k 10k

Hz

In this example, [low threshold] is -20dBu, [low level] is +12dB, [high threshold] is set to -5dBu, and [high
level] is 0dB. Thus the lowest trace shows an input at -25dBu with a standard parametric boost of +12dB at
1kHz. The -20dBu trace shows an identical response, as expected. However, once above this level, the filter
gradually fades out with increasing signal, until at all levels above 0dBu, the response is flat.

The shape of the curves for -5dBu and -10dBu require some explanation. These appear as they do because of
the nature of the frequency sweep measurement. The Helix equaliser uses a copy of the actual filter in use for
its level calculation, so that depending on the Q of the filter, our input signals are ‘ignored’ as we move away
from the centre frequency by the correct amount. Thus as the sweep measurement moves across the centre
frequency (1kHz in this case), the dynamic EQ is ramping smoothly in and out again, leading to the curves in
Figure 2. Note that if the level isoutside the range specifiedby the two thresholds,the unit behaves like afixed
parametric EQ. This means that we do not have to guess how much EQ will eventually be applied - it is
explicitly set in advance.

46

l abc

Without changing modes or making any other selections, we can make the unit operate ‘the other way up’just
by selecting suitable values for the two thresholds and levels see Figure3.

Figure 3  Helix with boost at high signal level 04/12/02 10:56:55

+20

+10

+0

d

-10

B
u

-20

-30

-40

10 20k20 50 100 200 500 1k 2k 5k 10k

Hz

In this case, [low threshold] is -20dBu, [low level] is 0dB, [high threshold] is -5dBu, and [high level] is
+12dB, so that instead of cutting this frequency range as the level increases, we are now boosting it. Again,
we have precise control over the maximum amount of boost that will be applied, and the level at which this
will occur. Note the shape of the curve for -5dBu, which has ‘expected values’ outside the filter range and at
the centre frequency, but intermediate values that show the EQ ramping in and out either side of the centre
frequency.

Needless to say, there is no requirement for one of the levels to be 0dB. Figure 4 shows the transition from a
+12dB boost at low level to a -12dB cut at high levels. Again, the intermediate curves show the effect of the
sweep signal moving in and out of the ‘area of interest’of the level detector as the curve is formed.

Helix with boost at low level and cut at high level 04/12/02 11:01:17

+15

+10

+5

+0

-5

d

-10

B

-15

u

-20

-25

-30

-35

-40
10 20k20 50 100 200 500 1k 2k 5k 10k

Hz

47

l abc

Application note 2 :What do we mean by all these Q types?

The “Q” of an audio equaliser describes the steepness of the filter - the degree to which it will affect signals
either side of its nominal or “centre” frequency. In general, the Q of a peaking filter is defined mathematically

as , where the bandwidth (in Hz) is the range of frequencies affected by the filter.

frequencycentre _

bandwidth

Because the frequency response of such a filter is a smooth curve (not a sharp “brick wall” filter like the ones
in an analogue-to-digital converter) we have to decide how we choose to define the bandwidth, and the
established convention is that we use the bandwidth to the “-3dB” points on either side of the centre
frequency, where the gain is 3dB less than the maximum gain.

Klark Teknik 06/19/02 17:16:50f=1.00kHz Q=2.2 Level= +12dB

+12
+10

+8

+6

+4

+2

d

+0

B

u

-2

-4

-6

-8

-10

-12
20 20k50 100 200 500 1k 2k 5k 10k

Bandwidth

Hz

3dB

.

In the example above, the filter is centred on 1 kHz, the lower 3dB point is at approximately 800 Hz, and the
upper one is at approximately 1.25 kHz.

This filter therefore has a Q of

1000

-

2.2

=

)8001250(

In a typical parametric equaliser (andin the case ofthe Helix systemthe graphic and dynamicsections too) we
have a manual control for the Q of the filter, and this allows us to set any Q that we require. In general high-Q,
narrow filters are used for notching out problem frequencies without affecting the programme material too
much, while gentler low-Q filters are useful for adjusting the tonal balance. In the case of graphic equalisers
there is another issue - that of interaction between adjacent bands. In general, lower-Q filters will blend
together more smoothly, but higher-Q filters provide more selective control of problems - at the expense of
more frequency response ripple.

So far so simple - but why the different types? This is due to the way in which the Q of the filter varies (or not)
when the gain control is adjusted. There are three modes available in the Helix system, which we term
Proportional, Constant, and Symmetrical Q.

48

l abc

Proportional Q

Klark Teknik 06/17/02 12:38:05Proportional Q

+12

+10

+8

+6

+4

+2

d

+0

B
u

-2

-4

-6

-8

-10

-12

20 20k50 100 200 500 1k 2k 5k 10k

Hz

Proportional Q is the mode of operation familiarto users of theKlark Teknik analogue graphic equaliserssuch
as the DN360. As the amount of cut or boost is increased, the Q also increases. This has the effect of making
the equaliser “focus” more tightly as the amount of EQ is increased. This allows a fairly low-Q filter at small
cut and boost settings, providing gentle control of tonal balance and low ripple. At high gain settings, a
proportional-Q equaliser “automatically” increases Q for moredramatic problem solvingsuch as suppression
of feedback or unwanted resonances. In the interests of clarity, the Q setting shown on the display is the Q at
full cut or boost - the Q at lower gain settings will be lower than that shown on the panel.

Constant Q

Klark Teknik 06/19/02 10:41:39Constant Q

+12

+10

+8

+6

+4

+2

d

+0

B
u

-2

-4

-6

-8

-10

-12

20 20k50 100 200 500 1k 2k 5k 10k

Hz

Aconstant Q equaliser has thesame Q at all cutand boost settings. In other words,the bandwidth between the
3dB points does not change at all as the gain is adjusted.The really important thing to notice about this is that
the resulting frequency response is NOT symmetrical in cut and boost. This is because of the definition of Q
which is based on the 3dB points The maximum gain of the filter when in cut is, of
course, 0dB, and the bandwidth is determined by the -3dB points and NOT relative to the

relative to maximum gain.

relative to 0dB

minimum gain (at the centre frequency). This makes a lot of sense musically too - if you listen to a music
signal and apply a notch filter, and then change the shape of the curve around theminimum gain (centre) point,
it will make little difference to the sound (since that area is already attenuated a lot). However, if you change
the curve around the 3dB points, this will affect the sound much more, as more or less of the signal “falls into”
the notch. It is bandwidth thatthe constant-Q filteris keeping constant.Note that many equalisersthat are

this

described as “Constant Q” by their manufacturers do NOT fall into this category, and are what we would term
symmetrical-Q designs.

49

l abc

Symmetrical Q

Klark Teknik 06/19/02 10:53:43Symmetrical Q

+12

+10

+8

+6

+4

+2

d

+0

B
u

-2

-4

-6

-8

-10

-12

20 20k50 100 200 500 1k 2k 5k 10k

Hz

This class of equaliser has the same curves in boost as the constant-Q type, but then has cut responses that are
symmetrical with the boost ones. In other words, the bandwidth in cut is defined not according to our usual
definition of Q (see constant-Q above) but as “the point were the signal is cut by 3dB less than the maximum
cut”. Most equalisers described by their manufacturers as “Constant Q” in fact produce symmetrical
responses.

50

Technical Specifications: DN9340

GRAPHIC

PARAMETRIC

DYNAMIC

FILTERS

CHAN

TYPE

BYPASS

B

A

SELECT

RECALL

STORE

HOME
(SETUP)

l abc

AL EQUALISER
IT

DIG

0

100
3
6

1

9

12
15
18
21
24

2

27
40

-

-

IN

B

A

0

75

3
6

50

1

9

25
0

12
15

100

18

75

21

50

24

2

25

27
40

0

-

-

-

OUT

-

DYN

A

B

B

A

DN9340

PUSH

SUPPLY
VOLTAGE

100-240V

CUS

AC~50-60Hz 60W

FUSE: 5x20mm
T0.5L250V

CAUTION: TO REDUCE RISK OF FIRE, REPLACE WITH SAME TYPE OF FUSE.

Inputs Two

Type Electronically balanced (pin 2 hot)
Impedance (Ohm) 20k
Common Mode >80dB @ 1 kHz
Rejection

Outputs Two

Type Electronically balanced (pin 2 hot)
Maximum Level +21dBu into >2k

Performance

Frequency response 0.3dB with all filters and EQ flat
(20Hz to 20kHz)
Distortion (THD+N) @ +4dBu <0.01%
(20Hz to 20 kHz)
Dynamic range 115dB
(20Hz-20kHz unweighted)

Processing (Per Channel)
Input Gain
Delay
Filters

+12dB to 40dB in 0.1dB steps plus Off
0-1 second (342.25 m or 333'10” at 20C in 20.8us steps)
4 Filters (max)

Types Low Pass, High Pass, Low Shelf, High Shelf, Notch

Dynamic EQ

2 Bands (max)
Range 12dB
Responses Proportional, Constant, Reciprocal

Parametric EQ

12 Bands (max)
Range 12dB
Responses Proportional, Constant, Reciprocal

Graphic EQ

31 Bands On ISO standard frequencies
Range 12dB
Responses Proportional, Constant, Reciprocal, DN27, DN360

PUSH

PUSH

Power Requirements

Voltage 90V to 250V a.c. 50/60 Hz
Consumption

60W

Terminations

Audio inputs/outputs 3-pin XLR
RS-485 inputs/outputs 3-pin XLR
RS-232 8-pin Mini-DIN socket (front)

9-pin D-type (rear)
Power 3-pin IEC

51

Dimensions

Width 483 mm (19inch)
Height 88 mm (3.5 inch) 2RU High
Depth 303 mm (12 inch)

Weight

Nett 5.5kg
Shipping 7.0kg

Technical Specifications: DN9344

l abc

0

100

0

75

3
6

50

1

1

9

25

0

12
15

100

18

75

21

50

24

2

25

27
40

0

PUSH

CUS

SUPPLY
VOLTAGE

100-240V
AC~50-60Hz 60W

FUSE: 5x20mm
T0.5L250V

COMMS

3
6

9
12
15
18
21
24

2

27
40

INOUT

PUSH

Inputs Four

Type Electronically balanced (pin 2 hot)
Impedance (Ohm) 20k
Common Mode >80dB @ 1 kHz
Rejection

Outputs Four

Type Electronically balanced (pin 2 hot)
Maximum Level +21dBu into >2k

Performance

Frequency response 0.3 dB with all filters and EQ flat
(20Hz to 20kHz)
Distortion (THD+N) @ +4dBu <0.01%
(20Hz to 20 kHz)
Dynamic range 115dB
(20Hz-20kHz unweighted)

0

100
3
6

1

9
12
15
18
21
24

2

27
40

PUSH

PUSH

0

75

3
6

50

1

9

25

0

12
15

100

18

75

21

50

24

2

25

27
40

0

DN9344DUAL SLAVE DIGITAL EQUALISER

PUSH

Processing (Per Channel)
Input Gain
Delay
Filters

+12dB to 40dB in 0.1dB steps plus Off
0-1 second (342.25 m or 333'10” at 20C in 20.8us steps)
4 Filters (max)

Types Low Pass, High Pass, Low Shelf, High Shelf, Notch

Dynamic EQ

2 Bands (max)
Range 12dB
Responses Proportional, Constant, Reciprocal

Parametric EQ

12 Bands (max)
Range 12dB
Responses Proportional, Constant, Reciprocal

Graphic EQ

31 Bands On ISO standard frequencies
Range 12dB
Responses Proportional, Constant, Reciprocal, DN27, DN360

Power Requirements

Voltage 90V to 250V a.c. 50/60 Hz
Consumption 60W

Terminations

Audio inputs/outputs 3-pin XLR
RS-485 inputs/outputs 3-pin XLR
RS-232 8-pin Mini-DIN socket (front)
Relay Socket 9-pin D-type (rear)
Power 3-pin IEC

Dimensions

Width 483 mm (19 inch)
Height 44 mm (1.75 inch) 1RU High
Depth 287 mm (12 inch)

Weight

Nett 5.5kg
Shipping 7.0kg

52

Service information

BATTERYREPLACEMENT

Caution!:

Danger of explosion if battery is incorrectly placed. Replace only with the same or equivalent type
recommended by the manufacture. Discard used batteries according to the manufacturer’s instruction.

Advarsel!:

Lithiumbatteri. Ekxplosionsfare ved feijlagtig handtering af samme fabrikat og type. Lever det brugte batteri
tilbage till leverandoren.

l abc

53

Klark Teknik Group DOC02-Helix System 04/06/03