KitchenAid KOWT100EBS, KOWT107EBS PRODUCT SPECIFICATIONS
24" (61 CM), 27" (68.6 CM), AND 30" (76.2 CM)
Front view
INDOOR/OUTDOOR ELECTRIC WARMING DRAWER
PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS
KOWT100E KOWT104E KOWT107E
ELECTRICAL CONNECTION
A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required.
A time-delay fuse or circuit breaker is also recommended. It is
recommended that a separate circuit serving only this warming drawer
be provided.
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
• Cutout dimensions that are shown must be used. Given dimensions
provide minimum clearance with warming drawer.
• Recessed installation area must provide complete enclosure around
the recessed portion of the warming drawer.
• Grounded electrical supply is required. See “Electrical Requirements”
section.
• Electrical supply outlet should be located in the rear wall on the upper
right-hand side of the cutout or in an adjacent cabinet. The outlet
must be recessed. If the electrical outlet is located in an adjacent
cabinet, a 1³⁄8" (3.5 cm) minimum diameter hole should have been
drilled in the back of the cutout or support surface to pass the power
supply cord through to the outlet.
• Warming drawer support surface must be solid, level and ush with
bottom of cabinet cutout.
• Warming drawers with oiled bronze, black glass, and white glass
panels are approved for indoor use only.
For best performance results make sure the warming drawer is leveled
before completing installation. There is no way to level the warming
drawer after it has been installed. If the installation is not level, the door
may slide open or not seal tightly, allowing heat to escape.
E
WARMING
DRAWER
SIZE
24"
(61 cm)
27"
(68.6 cm)
30"
(76.2 cm)
A
OVEN
DEPTH
(A)
8"
23¹⁄
(58.7 cm)
8"
23¹⁄
(58.7 cm)
8"
23¹⁄
(58.7 cm)
RECESSED
WIDTH
(B)
22¹⁄4"
(56.5 cm)
25¹⁄4"
(64.1 cm)
28¹⁄4"
(71.8 cm)
D
RECESSED
HEIGHT
(C)
9" (22.9 cm) 23³⁄4"
9" (22.9 cm) 26³⁄4"
9" (22.9 cm) 29³⁄4"
B
OVERALL
WIDTH
(D)
(60.3 cm)
(67.9 cm)
(75.6 cm)
C
DRAWER
FRONT
HEIGHT (E)
10¹⁄4"
(26.1 cm)
10¹⁄4"
(26.1 cm)
10¹⁄4"
(26.1 cm)
CABINET OPENING DIMENSIONS
Cabinet Front View
120 volt
grounded
outlet
(or located
in adjacent
cabinet)
A
Warming
drawer
cutouts
Toe
kick
B
A
B
C
D
E
Because Whirlpool Corporation includes a continues commitment to improve
our products, we reserve the right to change materials and specifications
without notice.
WARMING
DRAWER
SIZE
24"
(61 cm)
27"
(68.6 cm)
30"
(76.2 cm)
BETWEEN
CUTOUTS
(A)
2"
2¹⁄
(6.4 cm)
2"
2¹⁄
(6.4 cm)
2"
2¹⁄
(6.4 cm)
CUTOUT
HEIGHT
(B)
9¹⁄8"
(23.2 cm)
9¹⁄8"
(23.2 cm)
9¹⁄8"
(23.2 cm)
MINIMUM/
RECOMMENDED
(C)
1" (2.5 cm)/
4¹⁄4" (10.8 cm)
1" (2.5 cm)/
4¹⁄4" (10.8 cm)
1" (2.5 cm)/
4¹⁄4" (10.8 cm)
CUTOUT
WIDTH
(D)
22¹⁄2"
(57.1 cm)
25¹⁄2"
(64.8 cm)
28¹⁄2"
(72.4 cm)
Warming drawer can be installed as an indoor single or double
installation or installed under a single oven. Two warming drawers
under a single oven are shown.
NOTE: The warming drawer cannot be leveled after being installed.
For outdoor installation follow the cutout dimensions above. Install the
outdoor warming drawer in a permanent xture.
Custom Wood Drawer Front
If you plan to install a custom wood panel to match your cabinets, we
recommend consulting a qualied cabinetmaker or carpenter. The back
of the wood panel must be sealed to avoid moisture damage.
Dimensions are for planning purposes only. For complete details,
see Installation Instructions packed with product. Specifications
subject to change without notice.
MINIMUM
MINIMUM
CABINET
WIDTH
(E)
24"
(61 cm)
27"
(68.6 cm)
30"
(76.2 cm)
Page 1 of 2
Ref. W10713339A
03/15
Clearance Dimensions – Flush Installation
Front View
Side View
Top View
Flush Installation Requirements
A 25³⁄
8" (64.5 cm) minimum cutout depth is required.
These dimensions will result in a ¹⁄4" (6 mm) reveal on all sides of the warming drawer.
The front face of the cleats and platforms will be visible and should be treated as a nished surface.
Cabinet
Back
F
A
1" (25 mm)
Side Cleats*
⁷⁄₈” (22 mm)
Platform*
B
e
C
D
Side Cleat*
1⁵⁄₈" (4.1 cm)
27" Models 30" Models
A Width of flush inset cutout (minimum) 27¹⁄
B Height between cutouts (minimum) 2¹⁄
4" (69.2 cm) 30¹⁄4" (76.8 cm)
2" (6.4 cm) 2¹⁄2" (6.4 cm)
C Height of flush inset cutout (minimum) 10³⁄4" (27.3 cm) 10³⁄4" (27.3 cm)
Bottom of cutout to floor (recommended) 8¹⁄
D
Bottom of cutout to floor (minimum) 5" (12.7 cm) 5" (12.7 cm)
E Width of opening (minimum) 25¹⁄
F Depth of cutout (minimum) 25³⁄
4" (21.0 cm) 8¹⁄4" (21.0 cm)
4" (64.1 cm) 28¹⁄4" (71.8 cm)
8" (64.5 cm) 25³⁄8" (64.5 cm)
e Recommended outlet location
E
F
Because Whirlpool Corporation includes a continues commitment to improve
our products, we reserve the right to change materials and specifications
without notice.
Dimensions are for planning purposes only. For complete details,
see Installation Instructions packed with product. Specifications
subject to change without notice.
Page 2 of 2
Ref. W10713339A
03/15
Loading...