KitchenAid KIDS36EPSS, KIDS42EPSS Dimension Guide

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Briva™Dishwasher

PRODUCT MODEL NUMBERS OVERALL DIMENSIONS

CABINET OPENING DIMENSIONS

DISHWASHER DRAIN

KIDS36EP KIDS42EP

Electrical: 120-volt, 60-Hz, AC-only, 15- or 20-amp. electrical supply. Use copper wire only. A time-delay fuse or circuit breaker and separate circuit is recommended.

If using a Hot Water Accessory Tank and/or a garbage disposer, a separate 120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical supply is required for each devise.

Water: For dishwasher, a hot water line with 20-120 psi (138-827kPa) water pressure. Water temperature must be minimum 120°F (48.9°C) at dishwasher. Use 3/8" O.D. copper tubing with compression fitting is recommended. Use a 90° elbow with 3/8" N.P.T. external pipe threads on one end to connect to water inlet valve. Do not solder within 6" (15.2 cm) from water inlet valve. For sink faucet, hot and cold water line. Copper tubing with compression fitting for specific faucet to be installed.

Drain: Separate drain P-traps for sink and dishwasher.

Ref. 8564766

12-06-04

If the dishwasher drain exits through the back wall, the centerline of the drain must be a minimum of 1/2" (1.3 cm) below the dishwasher drain. This is required to completely drain the dishwasher tub so that no standing water remains in tub.

22-1/32"

(56.0 cm)

to bottom of

dishwasher

drain

1/2" (1.3 cm)

minimum

back

wall

Back right corner: If countertop is

more than 3/4" (1.9 cm) thick, measure down 3/4" (1.9 cm) and cut 45° bevel all the way around radius.

IMPORTANT: Corner radius dimensions specified must be used. If they are not, the dishwasher will not fit the opening.

radius: 2-1/4" (5.7 cm)

3/4"

(1.9 cm)

45°

for base cabinet

installations, min. 36"

(91.4 cm) width required

21-1/8"

(53.7 cm)

(see *NOTE)

It is recommended that sink water and drain line connections be located on this side of cabinet.

It is recommended that dishwasher water and drain line connections be located on this side of cabinet.

21-1/8"

(53.7 cm)

(see *NOTE)

backsplash

CRITICAL

RADIUS

radius: 1" (2.5 cm) – the right back corner must be cut to this radius

25" (63.5 cm) deep countertop

Countertop must be level.

7/16" (1.1 cm) min.

flat surface required

*NOTE: The cutout must be

accurately cut to the dimensions shown within 1/16" (1.6 mm). Dishwasher top flange overlaps the countertop cutout by 7/16" (1.1 cm) on front and back edges and 1/4" (6.4 mm) on sides.

• Cabinetry and countertop must be sturdy enough to support loaded dishwasher and sink (400 lbs. [181.4 kg]).

19-3/8"

(49.2 cm)

maximum

opened lid

height

20-21/32" (52.5 cm)

9-7/16"

(24.0 cm)

1-3/4" (4.4 cm) to center of single hole faucet

factory installed air gaps

dishwasher drain

water inlet valve

(between clamp rails)

22" (55.9 cm)

(between clamp rails)

5-25/32" (14.7 cm)

14" (35.6 cm)

18-5/16" (46.5 cm)

22-1/32" (56.0 cm)

21"

(53.3 cm)

1-1/4" (3.2 cm)

(20.3 cm)

center of

sink drain

5-1/2 ft. (1.7 m) 3-prong ground-type power supply cord

to center of single

hole faucet

GFCI reset buttons

SIDE FRONT

ABCD

42" model 40-1/2" 16-7/8" 9-9/16" 39-11/16"

(102.9 cm) (42.9 cm) (24.3 cm) (100.8 cm)

36" model 34-1/2" 10-7/8" 6-9/16" 33-11/16"

(87.6 cm) (27.5 cm) (16.6 cm) (85.6 cm)

42" model – 40" (101.6 cm)

36" model – 34" (86.4 cm)

(see *NOTE)