KitchenAid KICV167RMT, KICV167RSS Dimension Guide
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
VENTING REQUIREMENTS
KICV167R
Electrical: 120-volt, 60-Hz, AC-only, 15-amp.
electrical supply. Use copper wire only. A timedelay fuse or circuit breaker and separate circuit is
recommended.
36" Pro Line™ Series Island Range Hood
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 9763382
09-27-06
®
Horizontal wall venting
Vertical roof venting
elbow
wall
cap
Maximum length = 35 ft. (10.7 m)
1 — 90° elbow = 5 ft. (1.5 m)
8 ft. (2.4 m) straight = 8 ft. (2.4 m)
1 — wall cap = 0 ft. (0 m)
system length =13 ft. (3.9 m)
6 ft. (1.8 m)
2 ft.
(0.6 m)
6"
(15.2 cm) v
ent system
To calculate the length of the system
you need, add the equivalent feet for
each vent piece used in the system.
Note: Flexible vent is Not recommended.
18" (45.7 cm) min.
clearance upper
cabinet to countertop
X
36" (91.4 cm)
countertop height
30" (76.2 cm) or 36" (91.4 cm)
cabinet opening width
(if installed between cabinets)
See
Note
Vent piece 6" (15.2 cm) round
45° elbow 2.5 feet
(0.8 m)
90° elbow 5.0 feet
(1.5 m)
roof cap
wall
cap
Non-vented (recirculating)
Kit Nos. 4396911 and 4396912
chimney dimensions
Note:
The hood chimneys are adjustable
and designed to meet varying ceiling or
soffit heights depending on the distance “X”
between the bottom of the hood and the
cooking surface. For higher ceilings, a 40”
(10.2 cm) chimney extension Kit No. 4396913
or Kit No. 4396914 is available. The chimney
extension replaces the upper chimney
shipped with the hood. The chimney
extension can be cut as needed. For shorter
ceilings or soffits, the upper chimney can be
cut.
Important:
Minimum distance “X”: 24” (61.0 cm)
Suggested maximum distance “X”:
30” (76.2 cm)
As shown in charts below:
For vented installations, the chimneys can
be adjusted for ceilings between 7’ 7-1/8”
(2.31 m) and 9’ 1-3/4” (2.79 m).
For non-vented (recirculating) installations,
the chimneys can be adjusted for ceilings
between 8’ 3-3/8” (2.52 m) and 9’ 5-1/4”
(2.88 m).
Important:
As hood height (distance X)
increases, hood's venting effectiveness
decreases.
23
⁵⁄₈
"
(60.0 cm)
13
³⁄₄
"
(34.9 cm)
12
¹⁄₁₆
"
(30.6 cm)
4
³⁄₄
"
(12.1 cm)
35
³⁄₈
" (89.9 cm)
27
¹⁄₂
"
(69.9 cm)
26
³⁄₈
" (65.1 cm)
min.
39" (99.1cm)
max.
23
⁵⁄₈
"
(60.0 cm)
12
¹⁄₂
"
(31.8 cm)
3
¹⁄₂
"
(8.9 cm)
5"
(12.7 cm)
13
³⁄₄
"
(34.9 cm)
12
¹⁄₁₆
"
(30.6 cm)
32" (81.3 cm)
min.
39" (99.1 cm)
max.
overall
chimney
height
lower
chimney
height
upper
chimney
lower
chimney
height
overall
chimney
height
Loading...