King Industrial KC-1300BM Instruction Manual
10/2016
13-SPINDLE LINE BORING MACHINE
INSTRUCTION MANUAL
COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: KC-1300BM
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS LINE BORING MACHINE
OFFERS A 2-YEAR LIMITED WARRANTY
KING CANADA TOOLS
FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this product are available at our authorized King Canada service centers across Canada.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable
for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized
King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized
service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a 3prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire.
NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery due to wax and sawdust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the swich is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper
accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store materials such that it is necessary to stand on the tool to reach them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will operate properly and perform their intended function. Check for alignment of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other parts that
are da -maged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a
complete stop.
SPECIFIC SAFETY INSTRUCTIONS FOR LINEBORINGMACHINES
1. DO NOT attempt to use this machine until you are totally familiar with
how to operate it safely. Read instruction manual for details.
2. MAKE CERTAIN the machine is fastened to a supporting surface to
prevent it from tipping over during operation.
3. NEVER TURN LINE BORING MACHINE ON before clearing the
table of all objects (tools, scrap pieces, etc.).
4. ALWAYS KEEP hands, fingers and hair away from the rotating bits.
DO NOT ATTEMPT on material that does not have a flat surface, unless a suitable support is used.
5. ALWAYS CLAMP workpiece to table with hold-downs to prevent lift-
ing.
6. ALWAYS SUPPORT workpiece securely against fence to prevent ro-
tation.
7. BE SURE boring bits are sharp, undamaged and properly secured.
8. NEVER START line boring machine with bits pressed against the
workpiece.
9. NEVER PERFORM LAYOUT or assembly on the machine with cut-
ting tool rotating.
10. ADJUST DEPTH STOP to avoid drilling into the table.
11. ALWAYS STOP the machine before removing scrap pieces from the
table.
12. SHUT OFF POWER, remove boring bits, and clean the table before
leaving.
13. DO NOT WEAR gloves, neckties or loose fitting clothing.
14. NEVER PLACE YOUR FINGERS in a position where boring bits
could contact them if workpiece should shift unexpectedly.
15. NEVER USE DAMAGED BITS in the machine.
Loading...