Kidde PI2010 Brochure

Dual Sensor, 120V AC with
Battery Backup Smoke Alarm

Model PI2010 (Replaces Model PI2000)

Dual Sensor

Contains both a photoelectric and ionization sensor
providing dual sensor protection in your home.

Hush® Feature

Temporarily silences nuisance alarms.

Battery Backup

Provides protection even during a power outage.

Red LED

Flashes every 30-40 seconds to indicate that
the smoke alarm is operating properly.

Test/Reset Button

Tests unit’s electronic circuitry and horn.

Description

The Kidde PI2010 is a 120VAC, wire-in smoke alarm with
9V battery backup. This smoke alarm functions as a stand
alone unit or in an interconnected system. The Kidde
PI2010 features Hush®, allowing you to quickly silence
nuisance alarms and also includes a tamper resist features
that deters tampering and theft. The PI2010 includes a
quick connect power harness that allows for quick and
easy installation.

This smoke alarm combines both photoelectric and
ionization sensors. Ionization sensing alarms may detect
invisible fire particles (associated with flaming fires) soon­er than photoelectric alarms. Photoelectric sensing alarms
may detect visible particles (associated with smoldering
fires) sooner than ionization alarms.

Kidde strongly recommends that both ionization
and photoelectric smoke alarms be installed to help
insure maximum detection of the various types of
fire that can occur within the home.

The Kidde PI2010, 120VAC, wire-in smoke alarm
with 9V battery back up provides continuous protection
against smoke and fire hazards, even during power out­ages. The combination of ionization and photoelectric
sensors offer the best protection against both fast flam­ing and slow smoldering fires. The Kidde PI2010 inter­connects with up to 24 Kidde devices of which 18 can be
initiating. This unit also includes flashing LEDs to signal
the alarm is functioning properly, a low battery warning
and a loud 85dB alarm. The Kidde PI2010 is UL Listed
and includes a 10-year limited warranty.

Features and Benefits

• IonizationSensor – may detect invisible fire
particles (associated with flaming fires) sooner
than photoelectric alarms.

• PhotoelectricSensor – may detect visible particles
(associated with smoldering fires) sooner than
ionization alarms.

• Interconnect – Interconnects with up to 24
Kidde devices on one wiring network of which
18 can be initiating.

• BatteryBackup(9Vbatteryincluded) – Provides
continuous protection even during power outages.

• TamperResistant – Deters from tampering or theft.

• Hush® Feature – Temporarily silences nuisance alarms.

• RedLED – Flashes every 30-40 seconds to indicate

that the smoke alarm is operating properly.

• Test/ResetButton – Tests smoke alarm circuitry
and horn.

Dual Sensor, 120V AC with Battery Backup
Smoke Alarm

Model PI2010

(Replaces Model PI2000)

Architectural and Engineering
Specifications

The smoke alarm shall be Kidde Unit PI2010 or approved equal. It shall
be powered by a 120VAC, 60Hz, 80mA source along with a 9V battery
backup. The unit shall incorporate both an ionization smoke sensor and a
photoelectric smoke sensor with a nominal alarm sensitivity of 0.72-3.45%/
ft. The temperature operating range shall be between 40˚F and 100˚F (4˚C
and 38˚C) and the humidity operating range shall be up to 85% relative
humidity.
The smoke alarm can be installed on any standard single gang electri­cal box, up to a 4” octagon junction box. The electrical connection (to the
alarm) shall be made with a plug-in connector. A maximum of 24 Kidde
devices can be interconnected in a multiple station arrangement. The
interconnect system must not exceed the NFPA (National Fire Protection
Association) limit of 18 initiation devices, of which 12 can be smoke alarms.
With 18 initiation devices (smoke, heat, CO, etc.) interconnected, it is still
possible to interconnect 6 strobe lights and or relay modules. The unit shall
provide optional tamper resistance that deters removal of the unit from the
wall or ceiling.
The alarm shall include a test button that will electronically simulate the
presence of smoke and cause the unit to go into alarm. This sequence tests
the unit’s electronics, battery and horn to ensure proper operation.
The unit shall include a piezoelectric horn that is rated at 85 decibels at
10 feet. In a smoke incident, the horn will sound in the repetitive manner –
three (3) beeps, a pause, three (3) beeps, a pause.
The unit shall include the Hush® feature that silences the unit. By
pressing the Hush“ button, it will desensitize the unit for approximately
10 minutes if a nuisance condition occurs. The red LED will flash every 10
seconds during this time and will automatically reset after approximately 10
minutes and sound the alarm if particles of combustion are still present. The
Hush® feature shall be overridden and the unit will alarm if the smoke is too
dense.
The unit shall also include a low battery warning utilizing a brief alarm
chirp every 30-40 seconds for a minimum of seven (7) days.
The alarm will utilize a red LED that shall flash once every 30-40 seconds to
indicate the alarm is receiving power.
The unit shall at a minimum meet the requirements of UL217, NFPA72,
(chapter 11, 2002 edition) The State of California Fire Marshall, NFPA101
(One and two family dwellings) Federal Housing Authority (FHA), Housing
and Urban Development (HUD). It shall also include a 10-year manufac­turer’s limited warranty.

Installation of Smoke Alarm

The smoke alarm should be installed to comply with all local codes having juris­diction in your area, Article 760 of the National Electric Code, and NFPA 72.
Make certain all alarms are wired to a single, continuous (non-switched) power
line, which is not protected by a ground fault interrupter. A maximum of 1000
ft. of wire can be used in the interconnect system. Use standard UL listed
household wire (18 gauge or larger as required by local codes).

Technical Specifications

Model: PI2010

UPC Number: 0-47871-07915-5

Power Source: 120VAC with 9V battery backup

Sensor: Dual Ionization and Photoelectric

Audio Alarm: 85dB at 10ft

Temperature Range: 40˚F (4.4˚C) to 100˚F (37.8˚C)

Humidity Range: up to 85% relative humidity (RH)

Size: 5.75” in diameter x 1.8” depth

Weight: .4 lb

Interconnects: Up to 24 Kidde devices
(of which 18 can be initiating)

LED: Red, normal operation
Green - AC power present

Warranty: 10 year limited

Ordering Information

Individual UPC: 0-47871-07915-5 *not for sale by individual unit

Ordering   Dimensions  Cases/ Cases/ Layers/ Skid Units/
Number I2of5 PackQuantity (wxdxhinches) Weight Skid Layer Skid Weight Skid

n/a n/a individual* 5.75 x 2 x 5.75 .5lb n/a n/a n/a n/a n/a

21007915 100 47871 07915 2 Cut Case (6 gift-boxed units) 6.5 x 13.6 x 6.25 4.8lbs 126 21 6 605lbs. 756

Distributed by:

1016 Corporate Park Drive
Mebane NC 27302
1-800-880-6788
www.Kidde.com

P/N: KL-Pi2010 sheet rev. 09-2010