Kidde Firex Duct Detector Accessories English Owner's Manual

PRODUCT DESCRIPTION

The remote accessory is available with only the single gang remote indicator/control (591 Series), or with the addition of a single gang strobe assembly (592 Series), or as an optional field upgrade kit for existing installed 591 Series (593 Series). All versions are compatible with standard Decora style cover plates (base color choice plate included).

The indicator/control assembly provides

• Visual indication of detector Pilot, Trouble and Alarm Functions

• Selectable audible indication of Alarm, Trouble or both

• Buzzer Silence function, with “ringback” following condition correction

• Lamp/Buzzer test function

• Key-Operated detector Test and Reset functions

• Lever-operated “No-Tools” terminal block

• Port for plugging in Strobe Assembly

The strobe assembly provides visual indication of alarm conditions, and is connected to the indicator/control assembly via the provided connector (observing connector polarity).

NOTE: The strobe and audible buzzer features are not ADA

compliant, and not intended for life safety notification or evacuation purposes (public mode). These functions are for duct smoke detector status indication only (private mode).

STROBE CONNECTION

To install the Strobe module, simply plug the provided connector onto the pins as indicated on the rear of the indicator/control module. Snap the strobe lens into the cover plate, and install cover plate following completion of remote module wiring.

AUDIBLE BUZZER CONFIGURATION

There are two jumpers located on the rear of the indicator/control assembly. To enable audible buzzer operation for Alarm or Trouble conditions, simply leave the jumpers in place. To disable either or both functions, remove the appropriate jumper(s).

SILENCE AND RINGBACK FUNCTIONS

On the occasion where an audible alarm or trouble condition needs to be silenced while the detector condition is inspected and remedied, the indicator/control module provides a silence function. The slide switch located on the front of the module is pushed DOWN to activate the silence function.

Upon correction of the notified condition, the silenced buzzer will resume sounding. This the ringback feature which serves as a reminder to reset the silence switch to the “normal”, UP position.

Note that the strobe module, when used, will not stop operating when the silence function is engaged.

DUCT SMOKE DETECTOR REMOTE ACCESSORY

INSTALLATION GUIDE

191 E. North Avenue • Carol Stream, IL 60188 USA

Tech. Service Phone: +1 800 445 8299 • E-mail: technicalservice@invensys.com • www.invensys.com

INST APD0340 A060829

A COPY OF THESE INSTRUCTIONS SHOULD BE LEFT WITH THE EQUIPMENT UNTIL INSTALLATION BY ALL TRADES IS FULLY COMPLETE.

FOLLOWING FINAL INSPECTION, A COPY SHOULD BE LEFT WITH THE OWNER/USER.

NOTICE: The information contained in this document is the most current available at the time of shipment of accompanying product, and is subject to change without notice. Future references should always be made to the most current revision of this document. The information contained in all this document should be considered before installing or using the product. Any example applications shown are subject to the most current enforced local/national codes, standards, approvals, certifications, and/or the authority having jurisdiction. All of these resources, as well as the specific manufacturer of any shown or mentioned related equipment, should be consulted prior to any implementation. For further information or assistance concerning this product, contact Invensys. Invensys reserves the right to change any and all documentation without notice.

AVAILABLE ACCESSORIES FOR USE WITH

FIREX

DUCT SMOKE DETECTORS

REMOTE ACCESSORIES

591 Series Remote Accessory Controllers

591W Remote Indicator/Control Assembly w/ White Single Gang Cover Plate

591R Remote Indicator/Control Assembly w/ Red Single Gang Cover Plate

591S Remote Indicator/Control Assembly w/ Stainless Steel Single Gang Cover Plate

592 Series Remote Accessory Controllers with Strobe

592WC Remote Indicator/Control Assembly w/ Strobe Assembly (Clear Lens); White Double Gang Cover Plate

592WO Remote Indicator/Control Assembly w/ Strobe Assembly (Opaque Lens); White Double Gang Cover Plate

592RC Remote Indicator/Control Assembly w/ Strobe Assembly (Clear Lens); Red Double Gang Cover Plate

592RO Remote Indicator/Control Assembly w/ Strobe Assembly (Opaque Lens); Red Double Gang Cover Plate

592SC Remote Indicator/Control Assembly w/ Strobe Assembly (Clear Lens); Stainless Steel Double Gang Cover Plate

592SO Remote Indicator/Control Assembly w/ Strobe Assembly (Opaque Lens); Stainless Steel Double Gang Cover Plate

593 Series Remote

Accessory Strobes (as an optional field upgrade kit for existing installed 591 Controllers)

593RC Strobe Assembly (Clear Lens); Red Double Gang Cover Plate

593RO Strobe Assembly (Opaque Lens); Red Double Gang Cover Plate

593SC Strobe Assembly (Clear Lens); Stainless Steel Double Gang Cover Plate

593SO Strobe Assembly (Opaque Lens); Stainless Steel Double Gang Cover Plate

593WC Strobe Assembly (Clear Lens); White Double Gang Cover Plate

593WO Strobe Assembly (Opaque Lens); White Double Gang Cover Plate

SMOKE TEST GAS

565 Solo Aerosol Test Gas with Nozzle for 2650-760/761 Series Test Port

NOTCHED SAMPLING TUBES (2650-760/761 SERIES)

552 For duct widths of 1.0’ TO 2.5’

553 For duct widths of 2.5’ TO 5.0’

554 For duct widths of 5.0’ TO 10.0’

SAMPLING TUBES (2650-660/661, 2650-560/561 SERIES)

532 For duct widths of 1.0’ TO 2.5’

533 For duct widths of 2.5’ TO 5.0’

534 For duct widths of 5.0’ TO 10.0’

WEATHERPROOF ENCLOSURES

555 Weatherproof Enclosure for 2650-760/761 Series Detectors

590 Weatherproof Enclosure for 2650-660/661, 2650-560/561 Series Detectors

Normal

“Standby”

Mode

Silenced

Mode

ALM

TBL

Buzzer will function

on both Alarm

and Trouble conditions

ALM

TBL

Buzzer will function

on Alarm condition

only

ALM

TBL

Buzzer will function

on Trouble condition

only

ALM

TBL

Buzzer will not function

on Alarm or Trouble

conditions

REAR OF INDICATOR/CONTROL

191 E. North Avenue Carol Stream, IL 60188 USA Tech. Service Phone: +1 800 445 8299 E-mail: technicalservice@invensys.com www.invensys.com

591W

592WC

INST APD0340 A060829

2650-760/761 Series Duct Smoke Detectors

NOTE: A jumper wire must be placed between Terminals 20 and 15. The Trouble LED will illuminate when

the detector cover is removed, or if the smoke detector head is removed and the cover replaced. Trouble contacts CANNOT

be connected to a Fire Alarm Control Panel when using this option without the use of a slave

relay.

NOTE: If duct smoke detectors are interconnected for common functions, please refer to unit installation

guide for connection options for remote alarm functions.

2650-660/661 Series Duct Smoke Detectors

NOTE: A jumper wire must be placed between Terminals 14 and 18. The Trouble LED will illuminate when

the smoke detector head is removed. Trouble contacts CANNOT

be connected to a Fire Alarm Control Panel

when using this option without the use of a slave relay.

NOTE: If duct smoke detectors are interconnected for common functions, please refer to unit installation

guide for connection options for remote alarm functions.

2650-560/561 Duct Smoke Detectors

NOTE: A jumper wire must be placed between Terminals 16, 11 and 14. The Trouble LED will illuminate

when the smoke detector head is removed. Trouble contacts CANNOT

be connected to a Fire Alarm Control

Panel when using this option without the use of a slave relay.

NOTE: Use of a 590 Series Remote Accessory with these detector models requires the dedicated use of

one set of alarm contacts.

NOTE: These models of duct smoke detectors are not intended for interconnection when using the

590 Series Remote Accessories. For further information and assistance with this application, please contact our technical hotline.

C+

TB+

P+

C-

AL+

T/R

JUMPER

C+

TB+

P+

C-

AL+

T/R

JUMPER

C+

TB+

P+

C-

AL+

T/R

JUMPER

LAMP AND BUZZER TEST FUNCTION

The indicator/control module includes an integrated LED and Buzzer test function, to ensure that the visual and audible indicators are functioning and haven’t “burned out”. Simply depress the “LED TEST” button on the front of the module to activate test. If the remote accessory is functioning properly, all of the LEDs will illuminate, and the buzzer will sound (unless in “silence” mode or jumper programmed to not sound on alarm or trouble). Releasing the “LED TEST” button will return the unit to normal condition.

TECHNICAL SPECIFICATIONS

Power Requirements: Standby 13mA

Alarm LED 22mA Trouble with Buzzer 33mA Trouble Silenced 33mA Trouble without Buzzer 13mA Alarm with Buzzer 37mA Alarm Silenced with Buzzer 37mA Alarm with Buzzer and Strobe 154mA Alarm Silenced with Buzzer and Strobe 157mA Lamp Test with Buzzer 62mA Lamp Test with Buzzer Silenced 52mA

Sound Pressure: 60db @ 10 ft

Dimensions: Single Gang Plate 4½” (114.3mm)H x 2¾” (69.85mm)W

Double Gang Plate 4½” (114.3mm)H x 4½” (114.3mm)W

Wiring: 14-28AWG, Solid or Stranded

Approvals: UL Listed by Air Products and Controls Inc. for use with all Firex duct smoke detectors. Please refer to detector

and accessory cross reference table (page 3) for listed part numbers. UL URRQ.S7425 CSFM 7300-1004:107 MEA 73-92-E Vol.31

NOTE: For proper installation, testing, operation and maintenance of a duct smoke detector, please refer to the detector installation guide.

The following wiring diagrams are applicable only to compatible, current limited, UL Listed remote accessories from Firex. Use of any other devices may result in damage to the duct smoke detector or those devices, potential injury, and will void any applicable warranties.

WIRING INSTRUCTIONS

FRONT OF INDICATOR/CONTROL

PART NUMBER CROSS REFERENCE TABLE Models UL Listed as the following Air Products and Controls Inc. part numbers.

Remote Accessories Duct Smoke Detectors

PACKAGE CONTENTS AND STROBE CONSTRUCTION

Remote accessories that include the indicator/control unit are shipped with the following parts:

• Installation Instructions

• Indicator/Control Unit with back box mounting screws (back box not supplied)

• Keys for Test/Reset function

• Decora Style Cover Plate with mounting screws (single gang)

• “Duct Smoke Detector” Decal for optional use on cover plate

Remote accessories that include the indicator/control unit and strobe assembly are shipped with the following parts:

• Installation Instructions

• Indicator/Control Unit with back box mounting screws (back box not supplied)

• Keys for Test/Reset function

• Strobe Assembly with back box mounting screws (back box not supplied)

• Adhesive Strobe Shroud

(place over strobe assembly upon removal of paper bulb protector, refer to illustration at right)

• Strobe Lens

• Strobe Lens Decals for optional use: “SMOKE”, “FIRE”

(2 of each version in horizontal orientation plus 2 each vertically set)

• Decora Style Cover Plate with mounting screws (double gang)

• “Duct Smoke Detector” Decal for optional use on cover plate

Remote accessories that include the strobe assembly are shipped with the following parts:

• Installation Instructions

• Strobe Assembly with back box mounting screws (back box not supplied)

• Adhesive Strobe Shroud

(place over strobe assembly upon removal of paper bulb protector, refer to illustration at right)

• Strobe Lens

• Strobe Lens Decals for optional use: “SMOKE”, “FIRE”

(2 of each version in horizontal orientation plus 2 each vertically set)

• Decora Style Cover Plate with mounting screws (double gang)

• “Duct Smoke Detector” Decal for optional use on cover plate



FOR FURTHER PRODUCT SUPPORT

CONTACT OUR TOLL-FREE TECHNICAL ASSISTANCE HOTLINE: +1 800 445 8299

OR SEND AN E-MAIL: technicalservice@invensys.com

Cover Plate

w/decal

Strobe Lens

w/decal

Adhesive Strobe

Shroud

Strobe Assembly

STROBE CONSTRUCTION

Firex

Air Products and Controls Inc. 591W MSR-100R/W 591R MSR-100R/R 591S MSR-100R/S 592WC MSR-100RS/W/C 592WO MSR-100RS/W/O 592RC MSR-100RS/R/C 592RO MSR-100RS/R/O 592SC MSR-100RS/S/C 592SO MSR-100RS/S/O 593RC MSR-100S/R/C 593RO MSR-100S/R/O 593SC MSR-100S/S/C 593SO MSR-100S/S/O 593WC MSR-100S/W/C 593WO MSR-100S/W/O

Firex

Air Products and Controls Inc. 2650-760 SL-2000-N 2650-761 SL-2000-P 2650-660 SM-501-N 2650-661 SM-501-P 2650-560 SM-2650-560APC 2650-561 SM-2650-560APC