Page 1
Let’s Begin!
Cappuccino
& Latte System
Use and Care Guide
Page 2
IMPORTANT SAFEGUARDS
Safe Operation & Use
When using electrical appliances, basic safety precautions should be
followed, including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
3. This appliance must be properly installed
and located in accordance with these
instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock and
injury do not immerse cords, plugs or the
appliance in water or any other liquid.
8. Do not overfill the Water Reservoir
with water.
9. Use only water in this appliance! Do not
put any other liquids or foods in the Water
Reservoir except as instructed in the
Cleaning Instructions in this guide.
10. Unplug System before cleaning or
maintenance. Allow to cool before putting
on or taking off parts and before cleaning
the appliance. System automatically
enters standby mode after 2 minutes of
non use.
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
12. Do not operate any appliance with a
damaged cord or plug or after the
appliance malfunctions or is damaged
in any manner. Contact Keurig Customer
Service to report any malfunction of or
damage to the System.
13. Do not let the cord hang over the
edge of the table or counter, or touch
hot surfaces.
14. Close supervision is necessary when any
appliance is used by or near children.
15. Do not lift the Brew Handle to open the
System while brewing is in progress.
16. Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
17. This appliance is equipped with a
Power Cord having a grounding wire
with a grounding plug. The appliance
must be grounded using a 3-hole
properly grounded outlet. In the event
of an electrical short circuit, grounding
reduces the risk of electrical shock.
18. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
19. Do not, under any circumstances, cut or
remove the third (ground) prong from the
Power Cord or use an adapter.
20. Consult a qualified electrician
if the grounding instructions are not
completely understood, or if doubt exists
as to whether the appliance is properly
grounded.
21. Do not use the appliance for other than
its intended use.
SAVE THESE INSTRUCTIONS.
DO NOT permit children to use System unless there is adult supervision. System
dispenses very hot water.
™
CAUTION: There are sharp needles that puncture the Rivo
Pack Holder and in the bottom of the Rivo™ Pack Holder. To avoid risk of injury, do not put
your fingers in the Rivo
CAUTION: There is extremely hot water in the Rivo
To avoid risk of injury, do not lift the Brew Handle or open the Rivo
during the brewing process.
CAUTION: The Frothing Whisk is detachable and may pose a choking hazard.
WARNING: Very hot steam and liquid. Use only with Pitcher included. Operation with any
other pitcher or operation with no pitcher may result in injury.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the risk
of becoming entangled in or tripping over a longer cord. If an extension cord is used, (1)
the marked electrical rating of the cord set or extension cord should be at least as great
as the electrical rating of the appliance; (2) the cord should be arranged so that it will not
drape over the countertop or tabletop where it can be pulled on by children or tripped over
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
™
Pack Assembly Housing.
™
pack located above the Rivo
Pack Holder during the brew process.
™
Pack Assembly Housing
™
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN
TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
WARNING TO USERS AND PARENTS: DO NOT permit children to use System unless there
is adult supervision. System dispenses very hot water.
!
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE
DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
Page 3
WELCOME
Thank you for purchasing the Keurig® Rivo™ Cappuccino and Latte System. Before operating
™
the Rivo
clean and care for the System. We hope you enjoy crafting the perfect espresso, cappuccino,
latte and more!
System, we recommend carefully reading these instructions to learn how to use,
TABLE OF CONTENTS
WELCOME 5
SYSTEM OVERVIEW 6
PREPARING YOUR SYSTEM 8
CRAFTING YOUR FIRST BEVERAGE 10
THE RIVO
USING YOUR SYSTEM 12
HELPFUL HINTS 15
CLEANING AND MAINTENANCE 16
TROUBLESHOOTING 17
WARRANTY 18
Record Your Rivo™ System Serial Number Above
The serial number can be found on the bottom of the Rivo™ System gift box
and on the side of housing behind the Water Reservoir. Removing the serial
number label from the Rivo™ System will void warranty.
™
CONTROL PANEL 11
5
Page 4
SYSTEM OVERVIEW
CONTROL PANEL
RIVO™ SYSTEM
A Water Reservoir Lid
B Water Reservoir
C Power Cord
D Rivo
D1 Beverage Platform
FROTHING PITCHER
J Frothing Lid
K Frothing Whisk
(Detachable)
L Steaming Wand
(Detachable from Lid)
M Frothing Pitcher
™
Pack Bin
E Drip Tray Lid
F Drip Tray Overflow Indicator
G Drip Tray
H Power Button
I Brew Handle
CONTROL PANEL
N Short Espresso Button
O Espresso Lungo Button
P Cappuccino Froth Button
Q Latte Froth Button
R Cold Froth Button
A
B
C
D
P
N O
I
Q
H
R
Indicates components which are top-rack dishwasher safe.
Do not place any other component in the dishwasher.
The Keurig® Rivo™ System is not for use with K-Cup® packs or Vue™ packs.
6 7
D1
J
FROTHING
E
F
G
PITCHER
K
L
M
Page 5
PREPARING YOUR SYSTEM
1 Min
Prepare the Water Reservoir
STEP 1: Remove all packing materials from the Keurig
™
System and Frothing Pitcher. Place the System on
Rivo
a flat, stable surface away from water and heat sources.
Remove all adhesive tape and labels.
STEP 2: Lift and remove the Water Reservoir Lid, then
remove the Water Reservoir by lifting up and away from
™
the Rivo
STEP 3: Rinse the Water Reservoir and fill with water.
We recommend bottled or filtered water.
Hot water or any other liquid may damage the Water
Reservoir. Always ensure the Water Reservoir is filled to
the REFILL line before turning on the Rivo
System.
™
System.
®
Prepare the Brewing System*
STEP 1: Place a 12 oz. mug on the Drip Tray. Plug the Power
Cord into a grounded outlet and press the Power Button on
the right side of the System.
STEP 2: After about 1 minute, the Control Panel will flash
™
and you will hear a beep. This indicates the Rivo
is ready. Press the Espresso Lungo Button to run the first
cleansing brew. When brew is complete, discard the hot
water from the mug.
System
Prepare the Frothing System*
STEP 1: Remove packing material and static cling from
Frothing Pitcher and fill to MIN FILL with water. Secure
the Lid and place the Frothing Pitcher into the System.
STEP 2: Press the Latte Froth Button to run the first
cleansing froth. You will hear a beep when the cycle
is complete.
STEP 3: Remove the Frothing Pitcher from the System
and carefully remove the Lid. Discard the water and dry
all components.
*The first cleansing brew and cleansing froth cycles prepare the
System for your first beverage. It is normal for the System to be
slightly louder during these initial cycles.
™
*After brewing, the Rivo
for your next brew. As a safety feature, your System will
automatically shut off at any stage when it is idle for longer
than 2 minutes. Press the Power Button to restart.
You are now ready to craft your
System will automatically prepare
first beverage!
1 Min
8 9
Page 6
CRAFTING YOUR FIRST BEVERAGE
THE RIVO™ CONTROL PANEL
STEP 1
STEP 2
Brew Espresso
A Place a mug on the
Beverage Platform.
Froth Milk
B Lift the Brew Handle
and place a Rivo
pack into the System.
™
C Lower Brew Handle and
select your ESPRESSO
SIZE on the bottom row
of the Control Panel. After
about 1 minute, you will
hear a beep. This indicates
your espresso is complete.
FROTHING MODES
CAPPUCCINO FROTH
Creates more foam
and less steamed milk.
Perfect for a cappuccino
or macchiato.
SHORT ESPRESSO (1.4 OZ.)
Perfect for espresso beverages such
as a cappuccino, latte or macchiato.
Creates less foam and
more steamed milk.
LATTE FROTH
Perfect for a latte.
ESPRESSO LUNGO (2.8 OZ.)
Perfect for an americano
or iced latte.
*
COLD FROTH
Keeps your milk cold,
creates less foam and
more milk. Perfect
for an iced latte.
STEP 3
A Remove the Frothing
Pitcher from the System
and rinse thoroughly.
B Fill Frothing Pitcher with
fresh, cold milk.
Important: Add enough milk
to fill to MIN FILL, but do
not fill beyond MAX FILL. Do
not add ice, syrup or any other
ingredients to the milk prior
to frothing. Doing so may
damage the System.
C Return the sealed Pitcher
to the System by aligning
arrow on Frothing Lid.
Then select a FROTHING
MODE on the top row of
the Control Panel. After
about 90 seconds, you will
hear a beep. This indicates
your froth is complete.
Combine espresso with frothed milk and enjoy!
10 11
ESPRESSO SIZES
In order to ensure ideal pressure for espresso and frothed milk, the Rivo™
System is designed to perform one function at a time. Wait for brewing to
complete before selecting a frothing mode.
*Important: Add enough milk to fill to MIN FILL, but do not fill beyond
MAX FILL. Do not add ice, syrup or any other ingredients to the milk prior
to frothing. Doing so may damage the System.
Page 7
USING YOUR SYSTEM
MIN FILL
Crafting a Cappuccino
STEP 1: Place a 12 oz. mug on the Drip Tray and
prepare a Short Espresso (1.4 oz.) by selecting
the Short Espresso Button on the Control Panel.
STEP 2: Pour cold milk to MIN FILL of the
Frothing Pitcher (4.5 oz.) and place the Frothing
Lid on the Frothing Pitcher.
Important: Add enough milk to fill to MIN FILL, but do not fill
beyond MAX FILL. Do not add ice, syrup or any other ingredients
to the milk prior to frothing. Doing so may damage the System.
STEP 3: Return the sealed Pitcher to the System
and press the Cappuccino Froth Button.
If the Frothing Pitcher has not been positioned securely, you will hear
3 beeps when selecting a frothing mode. Remove the Frothing Pitcher
and re-insert, ensuring the Pitcher is securely in place.
Crafting a Latte
STEP 1: Place a 12 oz. mug on the Drip Tray and
prepare a Short Espresso (1.4 oz.) by selecting
the Short Espresso Button on the Control Panel.
STEP 2: Pour cold milk to MAX FILL of the
Frothing Pitcher (6 oz.) and place the Frothing
Lid on the Frothing Pitcher.
Important: Add enough milk to fill to MIN FILL, but do not fill
beyond MAX FILL. Do not add ice, syrup or any other ingredients
to the milk prior to frothing. Doing so may damage the System.
MAX FILL
STEP 3: Return the sealed Pitcher to the System
and press the Latte Froth Button.
If the Frothing Pitcher has not been positioned securely, you will hear
3 beeps when selecting a frothing mode. Remove the Frothing Pitcher
and re-insert, ensuring the Pitcher is securely in place.
STEP 4: When the milk is frothed, pull the
Frothing Pitcher from the System and carefully
remove the Lid. Pour the milk over the espresso
and enjoy!
12 13
STEP 4: When the milk is frothed, pull the
Frothing Pitcher from the System and carefully
remove the Lid. Pour the milk over the espresso
and enjoy!
Page 8
CARING FOR YOUSING YOUR SYSTEM
HELPFUL HINTS
MAX FILL
Crafting an Iced Latte
STEP 1: Fill a cup with ice and set aside. Place a
separate 3 oz. mug on the Beverage Platform
and prepare an Espresso Lungo (2.8 oz.) by
selecting the Espresso Lungo Button on the
Control Panel. Pour the espresso over the ice.
Important: Do not brew espresso directly into a glass cup filled
with ice. Doing so may cause the glass to crack or break.
STEP 2: Pour cold milk to MAX FILL of the
Frothing Pitcher (6 oz.) and place the Frothing
Lid on the Frothing Pitcher.
Important: Add enough milk to fill to MIN FILL, but do not fill
beyond MAX FILL. Do not add ice, syrup or any other ingredients
to the milk prior to frothing. Doing so may damage the System.
STEP 3: Return the sealed Pitcher to the System
and press the Cold Froth Button.
If the Frothing Pitcher has not been positioned securely, you will hear
3 beeps when selecting a frothing mode. Remove the Frothing Pitcher
and re-insert, ensuring the Pitcher is securely in place.
1 AUTOMATIC SHUT-OFF – As a safety feature, your System will automatically shut off
after it is idle for longer than 2 minutes. Just press the Power Button to restart.
2 EMPTy wATER RESERvOIR NOTIFICATION – If the Water Reservoir becomes
empty during brewing or frothing, the System will stop. The Control Panel will light up in
a circular pattern, flashing on the last mode used, and you will hear a series of beeps. If the
Water Reservoir is filled within 2 minutes, simply press the last used mode and continue
crafting your beverage. If more than 2 minutes have passed, the System will automatically
™
shut off. Press the Power Button and begin a new brew. You will need a new Rivo
3 FROTHING PITCHER NOTIFICATION – If the Frothing Pitcher has not been positioned
securely, you will hear 3 beeps when selecting a frothing mode. Remove the Frothing
Pitcher and re-insert, ensuring the Pitcher is securely in place.
4 THE RIGHT wATER – For the best tasting espresso, cappuccino or latte we recommend
using bottled or filtered water. We do not recommend using distilled or reverse osmosis water.
5 ICED BEvERAGES – Creating an iced latte or cappuccino is easy. Fill a cup with ice and
set aside. Brew espresso into a separate mug and pour the espresso over the ice. Use the
Cold Froth Button to froth milk and add the milk to the iced espresso. Important: Do not
brew espresso directly into a glass cup filled with ice. Doing so may cause the glass to crack
or break. Do not add ice, syrup or any other ingredients to the milk prior to frothing. Doing
so may damage the System.
6 THE DRIP TRAy AND RIvO™ PACK BIN – The Drip Tray is designed to capture excess
liquid from the brewing process and will fill with liquid after 10 to 12 brews. The Drip Tray
™
Indicator will become visible when the Drip Tray is almost full. The Rivo
™
up to 12 used Rivo
System. Empty contents of the Drip Tray into the sink and dispose of the used Rivo
Clean and dry both components before returning them to the System.
packs. Empty both components by carefully removing them from the
Pack Bin holds
pack.
™
packs.
STEP 4: When the milk is frothed, pull the
Frothing Pitcher from the System and carefully
remove the Lid. Pour the milk over the espresso
and enjoy!
14 15
7 CLEAN yOUR SySTEM REGULARLy – To keep your System looking and performing
at its best, be sure to clean the external and internal components as indicated on page 16.
8 STORING – When storing your System, empty and dry all components. Store your System
upright in a safe, dry, frost-free environment.
Page 9
TROUBLESHOOTINGWARRANTYCLEANING AND MAINTENANCE
Before cleaning the Keurig® Rivo™ System, unplug the Power Cord and wait for the System
to cool down. Unless otherwise noted, clean components with warm soapy water. Do not
use solvents, alcohol or other harsh substances. Do not place any components in an oven.
wATER RESERvOIR – The Water Reservoir should be cleaned regularly. The Water
Reservoir is not dishwasher safe. Wash by hand with warm water and mild soap.
FROTHING PITCHER – After each use, thoroughly clean all components of the Frothing
Pitcher. Place them on the top rack of the dishwasher or wash by hand with warm water
and mild soap.
Clean the interior components after every 10 to 12 beverages:
BREwING COMPONENTS – To clean the interior brewing components, place a mug on
a the Drip Tray. Lift and lower the Brew Handle without inserting a Rivo™ pack and press the
Espresso Lungo Button. When the process is complete, discard the water from the mug.
FROTHING COMPONENTS – Fill Frothing Pitcher to MIN FILL with water. Secure the Lid
and place the Frothing Pitcher into the System. Press the Latte Froth Button and wait for the
cycle to complete. Remove the Frothing Pitcher from the System and carefully remove the
Lid. Discard the water and dry all components.
DRIP TRAy AND RIvO™ PACK BIN – The Drip Tray is designed to capture excess liquid
from the brewing process and will fill with liquid after 10 to 12 beverages. The Drip Tray
™
Indicator will become visible when the Drip Tray is almost full. The Rivo
12 used Rivo™ packs. Empty both components by carefully removing them from the System.
Empty contents of the Drip Tray into the sink and dispose of the used Rivo™ packs. Clean and
dry both components before returning them to the System.
DE-SCALING – Mineral content in water varies from place to place. Depending on the
mineral content of the water in your area, calcium deposits or scale may build up in your
System. Scale is non-toxic, but left unattended, it can hinder System performance.
Visit www.keurig.com to view our recommended de-scaling procedure.
Pack Bin holds up to
SITUATION
System does not have power
System will not brew
System shuts off automatically
There is water in the Drip Tray
Red Indicator appears in Drip Tray
The Control Panel Buttons are
If other issues arise with your System, call Keurig Customer Service at 1.866.901.BREW (2739).
Damage to the System resulting from the failure to follow these instructions will void the warranty.
System will not brew
when used for the first time
The Power Button does
not turn System off
The System pump is
making a loud sound
The Brew Handle
won’t close
The espresso tastes weak
The milk does not froth
flashing in a circular pattern
SOLUTION
• Plug System into an independent outlet.
• Make sure the Power Button is pressed.
• During normal operation, the System will shut off when it is
idle for longer than 2 minutes. Just press the Power Button
to restart.
• Check to be sure that the System is plugged in securely.
• Plug into a different outlet.
• Reset your home circuit breaker, if necessary.
• Make sure the System has power (see above).
• Check that the Water Reservoir is filled.
• System may be cold or frozen. Let System rest at room
temperature for at least 2 hours before powering on.
• Make sure the System has power (see above).
• Under normal operation, the System will shut off when it is idle
for longer than 2 minutes. Just press the Power Button to restart.
• If the System shuts off in the middle of a brew (not from power
outage), make sure the Water Reservoir is filled.
• Remember that any liquid overflow (from your mug or the
Water Reservoir) will be caught in the Drip Tray.
• When the Drip Tray is almost full, the red Drip Tray Overflow
Indicator will appear. Carefully remove the Drip Tray (there
may be hot liquid in it). Empty contents into the sink.
• The Power Button will only restart or turn on the System. It will
not turn the System off. The System will automatically shut off
after 2 minutes (see “System shuts off automatically,” above).
• This means that the Drip Tray is almost full. Carefully remove
the Drip Tray (there may be hot liquid in it). Empty contents
into the sink.
• The Water Reservoir needs to be refilled.
• Empty the Rivo
™
• A Rivo
the Brew Handle to adjust the Rivo
• Ensure you are using a new Rivo
be reused.
• Make sure you are using cold milk. Milk at room temperature
will not froth well.
• The Water Reservoir needs to be refilled.
™
Pack Bin.
pack may have been inserted incorrectly. Lift and lower
™
pack.
™
pack. Rivo™ packs cannot
16 17
Page 10
WARRANTY
Limited One Year Warranty
Keurig warrants that your Brewer will be free of defects in materials or workmanship under normal
home use for one year from the date of purchase. It is recommended that you fill out and return the
warranty card enclosed with your Brewer so that your purchase information will be stored in our system.
Keurig will, at its option, repair or replace a defective Brewer without charge upon its receipt of proof
of the date of purchase. If a replacement Brewer is necessary to service this warranty, the replacement
Brewer may be new or reconditioned. If a replacement Brewer is sent, a new limited one year warranty
will be applied to the replacement Brewer.
This warranty only applies to Brewers operated in the United States and Canada. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state and, in the case of
Canada, from province to province.
Only the use of Keurig Brewed® Rivo™ brand packs and accessories will guarantee the proper functioning
and lifetime of your Keurig Brewer. Any damage to or malfunction of your Brewer resulting from the use
of non Keurig Brewed® Rivo™ brand packs and accessories may not be covered by this warranty or may
result in a service fee if the defect is determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING
FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not
allow the exclusion or limitations of incidental or consequential damages, so the above limitation or
exclusion may not apply to you depending on the state or province of purchase. Nor does this warranty
cover damages caused by use of non Keurig® Rivo™ brand packs or accessories, services performed by
anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig
parts, or external causes such as abuse, misuse, inappropriate power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY, WHETHER
WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER
WARRANTIES WITH RESPECT TO YOUR R500 SYSTEM, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not
allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the
above limitation may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?
Keurig Systems are high-quality appliances and, with proper care, are intended to provide years of
satisfying performance. However, should the need arise for warranty servicing, simply call Keurig
Customer Service at our toll free phone number 1.866.901.BREW (2739). Please do not return your
System for servicing without first speaking to Keurig Customer Service to obtain a Returns Material
Authorization (RMA) number. Keurig Systems returned without an RMA number will be returned to the
sender without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
18
Page 11
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a
wholly-owned subsidiary
of Green Mountain
Coffee Roasters, Inc.
For Household Use Only
Made in China.
Printed in China.
© 2012 Keurig, Incorporated
All rights reserved
www.keurig.com | 1.866.901.BREW
P/N 60-202 246- 000 Re v A 06/ 12
Loading...