Kettler 08947-467, 08947-460, 08947-465 User Manual
Montageanleitung und Handhabungshinweise
Fahrrad-Kindersitz „TEDDY”
Art.-Nr. 08947-460, -465, -467
Der Umwelt zuliebe: wir drucken auf 100% Altpapier!
Abb. ähnlich
F
GB
D
USA
NL
Assembly Instructions
USA
GB
KETTLER´s child’s seat was designed incompliance with applicable safety regulations and manufactured under permanent quality control. The knowledge gained in this process is used to constantly improve and develope our products. In order to offer our customers the very best in quality, we reserve the right to make technical changes at
Please read these instructions carefully before the assembly and first use. You will get important information on
your safety as well as the use and maintenance of the child’s seat. Retain these instructions for information and
for maintenance works as well as orders for spare parts.
4
5
Assembly Instructions
USA
GB
any time. Should you have the need of assistance, please conntact your dealer.
For Your Safety
■ Only use this bicycle child's seat for its intended purpose, i.e. only mount it above the bike's rear axle by me-
ans of the included mounting parts and only use it for the transport of children.
■ The seat is suitable for children who can already sit alone (about 9 months), and may be loaded with a maxi-
mum weight of 22 kg including luggage. (Check regularly with the age of the child).
■ This child's bicycle seat is not suitable for fully sprung bicycles.
■ The child’s seat can be used for bicycles with a minimum wheel diameter of 26 inches; the diameter of the fra-
me tube must be 28, 30, 32, 35 or 40 mm.
■ Any other use is inadmissible and may even be dangerous. The manufacturer cannot be held liable for dama-
ge caused by unauthorized use.
■ The bicycle used must be safe and correspond to the Road Traffic Licensing Regulations valid in your country.
Please make enquiries if there are regulations concerning the transport of children.
■ If you have a special bicycle structure please ask your dealer if your bike is suitable for the use of a child's seat.
■ The bicycle must be suited for accepting such additional loads. Furthermore, the admissible total weight of the
bicycle including child and child's seat must not be exceeded. If necessary, ask your bicycle manufacturer or
supplier regarding the bicycle's carrying capacity.
■ If you transport your bicycle on a luggage rail on your car, you should dismount the child's seat from your bicy-
cle to avoid exceeding the carrying capacity of the luggage rail.
■ When attaching the seat to a bicycle that has a saddle stem with suspension please take into account the di-
stance between the seat and the suspension spring. You should ensure that the child’s fingers cannot reach the
spring thus avoiding the danger of injury.
■ Please note that the riding behaviour of the bicycle changes when the child’s seat is used (irrespective of child
being transported or not). Owing to the higher centre of gravity the bicycle's behaviour may change unfavourably and the bicycle's dirigibility may be impaired. For this reason, ride carefully – in particular with regard to
braking and evading manoeuvres. Also avoid riding with one hand only.
■ Pay attention that the child does not handle any objects (e.g. toys) which might get caught in the wheels. Clo-
thes or extremities of the child should never be able to get caught in turning parts or in the brake and transmission system.
This should be checked regularly as the child grows older.
■ Protect your child from sharp edges of your bicycle, from worn cables and other parts that might lead to inju-
ries.
■ Before going on a ride, and during breaks, you should check that the seat is firmly attached, and also check all
components for potential damage and loose connections (screws, connections, safety belts etc.).
■ Attention: Only transport the child with the safety belt correctly and firmly fastened and the foot straps closed.
Have a check during breaks that those safety devices are still in place.
■ Even if no child is carried, close the seat belt to avoid it getting caught in turning parts or catching on items that
are passed during the ride.
■ Pay attention to suitable and sufficiently warm clothing of your child. Children who are sitting still normally cool
down faster than the rider.
■ We recommend that adult and child wear suitable helmets.
■ Adjust the headrest so that its upper edge matches the child's ear level.
■ If in doubt or if you have any further questions do not hesitate to contact your specialized dealer.
■ Attention: Do not attach additional luggage to the child's seat. If necessary, use a carrier for the front axle in or-
der to obtain a balanced load. Please note that the carrying capacity of bicycle and child's seat are not exceeded.
■ Attention: The seat must not be modified. The child’s bicycle seat meets all required safety regulations. Repair
works done by non-experts and alterations to the construction (dismounting original parts, attachment of parts
without approval etc.) may cause harm to the user.
■ Attention: Please note that the riding behaviour of the bicycle may change with a child in the seat, especially
regarding balance, steering and braking. Ask the child to sit quietly. Sudden weight transfers by the child may
6
Assembly Instructions
USA
GB
considerably affect your safety during the ride.
■ Attention: Never park the bicycle with the child still in its seat.
■ Attention: Do not use the seat if one of its components is defective. Damaged components may jeopardize your
or the child’s safety. Before going on a ride you should check all components for potential damage and loose
connections (screws, connections, safety belts etc.). Damaged or worn components must be replaced immediately. Only use original KETTLER spare parts.
■ Attention: In case of extreme weather conditions please check if the seat can be used by the child, as for ex-
ample the seat may become very hot when there is strong solar radiation, or if the temperature is far below freezing point the skin may stick to the seat or its components.
Assembly
■ The child’s seat must be positioned such that it is not in contact with the luggage carrier. The distance between
luggage carrier and tube shackle must be min. 25 mm.
■ Fix the tube shackle parallel to the ground. This results in a seat which is slightly inclined towards the rear such
that the child may not slide out of the seat. The seat back is slighty inclined to the rear.
■ The load centre (marked by a red point) may only be within 10 cm behind the wheel hub (explained in detail
below).
■ In case of saddles with uncovered springs the latter have to be covered as a protection against bruises (e. g.
art. nr. 08947-690).
■ Further to that the rear wheel is provided with an additional cover on the spokes or a protective device to pre-
vent dresses from getting mingled with the spokes.
■ Tighten all screws with a torque of approx. 6 Nm. Check the tight fit of all screwed connections after assembly.
■ Please check whether all parts of the bike operate correctly with the set fitted in place (e.g. steering and bra-
kes).
Service and maintenance
■ Always use environmentally friendly substances, never aggressive or caustic ones, for cleaning and servicing
the child’s bicycle seat.
■ If necessary you may also clean the safety belts. In this case it is especially important not to use aggressive sub-
stances! Usually weak washing-up water or a mild detergent will be sufficient.
■ If seat or clothes are damp the colour of the seat may possibly mark pale coloured clothes due to friction.
Accessories
■ If you want to attach the seat to another bicycle, you can order a second carrier for the child’s seat. (item no.
8947-633).
■ To secure the child’s seat from theft, a cylinder lock can be inserted into the seat support bracket. The lock (type
K.01.32.G1) is not supplied with the seat. The lock is obtainable from: Firma P.C. Fischer, Kaiserstraße 126, D58300 Wetter/Ruhr, tel. (0) 23 35/42 64, fax (0) 23 35/58 46
Note on Assembly
Assembly must be carried out carefully by an adult.
Carefully read these mounting instructions before beginning with the work itself. The individual steps are additio-
nally explained in the sequence of figures by means of symbols, in some cases a text mark indicates that a written explanation is available. Strictly follow the individual mounting steps to ensure a safe use and operation of the
unit.
For technical reasons, we reserve the right to carry out preliminary assembly work (e.g. addition of tubing plugs).
3 Years Guarantee
■ KETTLER guarantees that this product has been manufactured with the greatest care using materials of the highest
quality. However, should you have reason for complaint, please contact your dealer. Do not forget to submit your
Assembly Instructions
GB
receipt of payment. The guarantee commences on the date of purchase. Entitlement to service under the guarantee
does not recommence if repairs are carried out.
■ Damage caused by incorrect treatment or the use of force is not covered by this guarantee.
■ Similarly, the manufacturer is not liable for damage to the product caused by environmental factors (e.g. air or
(rain)water pollution). Any costs arising from the repair of damage of this kind will not be assumed by the manufacturer.
List of spare parts page 22-23
When ordering spare parts, always state the full article number, spare-partnumber, the quantity required and the
S/N of the product (see handling).
Example order: Art. no. 08947-460 / spare-part no. 10104000 / 2 pieces / S/N .................... Please keep
original packaging of this article, so that it may be used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in (internal) packaging, which is safe for transportation,
in the original box if possible.
It is important to provide a detailed defect description / damage report!
Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.) is re-
quired, this should be clearly stated on the order by adding the words „with fastening material“.
Waste Disposal
KETTLER products are recyclable. At the end of its useful life please dispose of this article correctly and safely (local refuse sites).
KETTLER (GB) Ltd.
Merse Road · North Moons Moat · Redditch, Worcestershire B98 9HL · Great Britain
http://www.kettler.co.uk
KETTLER International Inc.
1355 London Bridge Road · VA 23450 Virginia Beach USA
http://www.kettlerusa.com
GB
USA
USA
13
Messhilfe für Verschraubungsmaterial
0 102030405060708090100110
M5x40
M8x40
M8
ø22
ø16
ø12
M6
M5
3,9x13
Measuring help for screw connections Gabarit pour système de serrae
Meethulp voor schroefmateriaal
F
GB
NL
14
4
2 3
ø18
A
B
C
D
ø12M6x100
1
40 mm 35 mm 32 mm 30 mm 28 mm
ø30
ø30
Loading...