KEPCO KIT 219-0528 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

219-0528

CABLE KIT NO. 219-0528

BOP 26600 MODELS (2) IN PARALLEL

I. DESCRIPTION

This kit contains the cables and terminations required to operate two identical 750 Watt Model 26600
BOP power supplies in parallel, effectively multiplying the output current capacity by two.

Refer to the associated technical manual supplied with the 750 Watt Model 26600 BOP power supply
for all instructions regarding installation and operation of multiple units in parallel.

!

CAUTION: Failure to install the ground cable supplied can result in damage to the power supply.

II. SPECIFICATIONS

Table 2 lists the general specifications for the parallel combination of two identical 750 Watt Model
26600 BOP Power Supplies. For specifications not listed in Table 2, refer to the General Specifications
provided in the associated technical manual supplied with the Model 26600 BOP power supply

TABLE 1. EQUIPMENT SUPPLIED

Item Quantity Purpose

Output and Common

Power cable

(1.5 ft.)

Parallel Control Cable

(1.5 ft.)

Protection Cable

(1 ft.)

Master - IN Parallel
Control Termination

Protection - OUT

Termination (Slave)

Protection - IN

Termination (Master)

Instruction

Manual

Nut 2

Output Sense Cable 1 Connects Output sense terminal to Common sense terminal of next unit. 118-1271

Chassis Ground Cable 1 Connects chassis ground terminals of all units. 118-1272

Ground Cable mounting

hardware

2

1

1

1

1

1

1

2 sets Each set consists of eight parts, mounted in the following order: No. 10 star lock-

Connects the OUTPUT and COMMON terminal of the Master to the OUTPUT
and COMMON terminals of the Slave. 118-1112

Provides control signals required for parallel operation.

Provides interlock protection signals required for multiple unit operation.

Provides proper termination for Parallel Control Cable.

Provides proper termination for the slave connection to the Protection Cable.

Provides proper termination for the master connection to the Protection Cable.

Lists material supplied.

Overcomes tight space for output cable connections. After securing bottom cable
to output terminal stud using one nut, additional cables can be oriented for best
layout and secured with separate nut.

washer P/N 103-0106 (at chassis), No. 10 flat washer P/N 103-0031, No. 10 split
lockwasher P/N 103-0033, 10-32X3/8 nut P/N 102-0008, No. 10 flat washer P/N
103-0031, [lug(s) from ground cable], No. 10 flat washer P/N 103-0031, No. 10
split lockwasher P/N 103-0033, and 10-32X3/8 nut P/N 102-0008.

Kepco Part

Number

118-1202

118-1126

195-0109

195-0108

195-0107

228-1634

102-0046

(See

Purpose

at left for part

numbers)

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

http://www.kepcopower.com  email: [e-mail]

228-1634 REV 2 051412

TABLE 2. GENERAL SPECIFICATIONS FOR TWO (2) IDENTICAL BOP 1000 WATT UNITS (PARALLEL)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 15.0A a-c maximum

264 Va-c 10A a-c maximum

Leakage current 7mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

d-c Output Range E

O Max

I

O Max

Closed Loop Gain Voltage Channel 0.6

Current Channel 25.0

Source/sink
adjustment range

Programming
resolution / accuracy

Voltage –6V to +6V

Current –250A to +250A

Voltage ±6mV

Current ±375mA

Voltage Limit ±6mV linearity ±120mV Full Scale tolerance

Current Limit ±375mA linearity ±2.75A Full Scale tolerance

Readback
resolution / accuracy

Voltage Same as individual unit Independent readings for each unit

Current Same as individual unit Independent readings for each unit

Current stabilization in current mode

Source effect ±125mA Min - max input voltage

Load effect ±500mA 0 to 100% load current

Time effect (drift) ±125mA 0.5 through 24 hours

Temperature effect ±125mA / °C 0° to 50°C

Ripple and noise ±5Ap-p Includes switching noise.

Voltage stabilization in voltage mode Same as individual unit

Rise/Fall Time

Voltage 250

Current 1.5mS/1.5mS

Frequency bandwidth

Voltage 2KHz

Current 400Hz Short circuit, I

±6V d-c

±250A d-c

µS/250µS

Nominal resistive load, measured from
10 to 90%, 0 to ±100% of rating

Short circuit, measured from 10% to
90%, 0 to ±100% of rating

Nominal resistive load, E
I

OPK

= I

ONOM

@ 60Hz

= I

OPK

ONOM

OPK

@ 60Hz

= E

ONOM

,

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1634 REV 2 051412