KEPCO KIT 219-0508 User Manual
INSTRUCTION MANUAL
KEPCO
An ISO 9001 Company.
KIT
219-0508
CHASSIS SLIDES KIT NO. 219-0508
1. DESCRIPTION
This Kepco KIT contains the components required to install bottom-mount chassis slides on Kepco RA 19-4C Rack
Adapters..
2. INSTALLATION OF CHASSIS SLIDES
2.1 MATERIAL SUPPLIED (SEE TABLE 1.)
TABLE 1. MATERIAL SUPPLIED
MATERIAL QUANTITY
Slide, Kepco P/N 108-0458 (Accuride 3012590, modified) 2
Screw, 6-32 x 1/4 in. long, Kepco P/N 101-0458 4
Instruction Manual, Kit 219-0508 1
2.2 PROCEDURE (SEE FIGURES 1, 2, 3.)
1. Remove four feet from bottom of RA 19-4C chassis.
2. Attach slides (108-0458) to each side of rack adapter using four screws (101-0458) (see Figure 1). Locate the
locking detent towards the rear of the chassis to ensure forward travel.
3. Attach slides to cabinet using mounting holes “A.”
F
O
R
W
A
R
D
T
R
A
V
E
L
A
A
A
A
LOCATE LOCKING DETENT
TOWARD REAR OF CHASSIS
AS SHOWN FOR FORWARD
TRAVEL.
A
A
A
SCREW, P/N 101-0458
3043096
6-32 X 0.250 IN. LONG
(QTY 2 PER SLIDE, 4 TOTAL)
A
SLIDE, P/N 108-0458
LEFT AND RIGHT, 20 IN. LONG,
(ACCURIDE 3012590, MODIFIED)
FIGURE 1. INSTALLING CHASSIS SLIDES ON RACK ADAPTER (3/4 VIEW OF BOTTOM)
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL (718) 461-7000 " FAX (718) 767-1102
http://www.kepcopower.com " email: hq@kepcopower.com
©2006, KEPCO, INC 1
Data subject to change without notice 228-1571
19.000 [482.6]
[
5.218
[132.54]
6.758
[171.65]
CUSTOMER SUPPLIED SCREW
MOUNT SLIDE TO CABINET
(SEE "A" HOLE DIMENSION
FOR SIZING)
1.540 [39.12]
0.186 [4.73]18.625 [473.07]
NOTES: 1. DIMENSIONS IN INCHES, DIMENSIONS IN BRACKETS ARE IN MILLIMETERS.
3043098
2. TOLERANCES ARE ±0.015
±0.38] UNLESS OTHERWISE SPECIFIED.
FIGURE 2. INSTALLING CHASSIS SLIDES ON RACK ADAPTER (FRONT VIEW)
.
0.439 [11.15]
1.351 [34.32]
11.000
[279.4]
7.000
[177.8]
18.125 [460.37]
A
0.250 [6.35]
0.250
[6.35]
7.375 [187.32]
2.000
[50.8]
14.625 [371.47]
A
1.500 [38.1]
A
20.351
[516.92]
20.000
[508.0]
A
18.44
[468.38]
18.000
[457.2]
3043097
A
"A" HOLES
A
NOTES: 1. DIMENSIONS IN INCHES, DIMENSIONS IN BRACKETS ARE IN MILLIMETERS.
2. TOLERANCES ARE ±0.015 [±0.38] UNLESS OTHERWISE SPECIFIED.
0.172"X0.234" OBROUND
MOUNT SLIDE TO CABINET
A
A
FIGURE 3. INSTALLING CHASSIS SLIDES ON RACK ADAPTER (BOTTOM VIEW)
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL (718) 461-7000 " FAX (718) 767-1102
http://www.kepcopower.com " email: hq@kepcopower.com
2 228-1571 050406
Loading...