KEPCO KIT 219-0480 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

219-0480

CABLE KIT NO. 219-0480

BOP 1000W MODELS 2 X 2 COMBINATION

I. DESCRIPTION.

This kit contains the cables and terminations required to operate a multiple unit combination consisting of two
parallel branches each comprised of two identical 1000 Watt BOP High Power models in series, effectively dou­bling the output voltage and doubling the output current capacity. Only identical models may be configured to
operate in parallel and series.

This kit can be used with all 1000W BOP models that have revision levels as shown in Table 1. Earlier models

!

that have been upgraded to permit multiple unit configurations must include the letter “A” following the revision
number. CAUTION: Failure to install the ground cables supplied can result in damage to the power supply.

Refer to the associated technical manual supplied with the 1000W BOP power supply for all instructions regard­ing installation and operation of multiple units in parallel.

TABLE 1. REVISION LEVELS APPLICABLE TO THIS KIT

MG Model Revision

BOP 6-125MG All All

BOP 10-75MG 5 or higher 3A or 4A

BOP 20-50MG 8 or higher 5A, 6A or 7A BOP 20-50GL All

BOP 25-40MG All All

BOP 36-28MG 11 or higher 8A, 9A or 10A

BOP 50-20MG 7 or higher 5A or 6A BOP 50-20GL All

BOP 72-14MG 7 or higher 6A

BOP 100-10MG 6 or higher 2A or 4A

Revisions for previously Upgraded

Units (Must include “A”)

GL Model Revision

II. SPECIFICATIONS

Table 3 lists the model parameters unique to a 2 X 2 multiple unit combination of identical 1000W BOP Power
Supplies (two series-connected units X two parallel branches). Table 4 lists the general specifications applicable
to all 2 X 2 multiple unit combinations listed in Table 3. For specifications not listed in Table 3, refer to the General
Specifications provided in the associated technical manual supplied with each 1000W BOP power supply.

Item Quantity Purpose Kepco Part Number

Common power
cable, ** (4.5 ft.)

Output/Series Power

cable, (1.5 ft.)

Configuration Control

cable, (2.5 ft)

Series Control cable,

(1.5 ft.)

Digital Control (Bitbus)

Cable, (4.5 ft.)

** For GL units: Unclamp and remove ferrite from cable before installation.

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

TABLE 2. EQUIPMENT SUPPLIED

Connects the COMMON terminal of Master to the COMMON terminal of

1

Slave #3.

Connects the OUTPUT terminal of Master to the COMMON terminal of

3

Slave #1, OUTPUT terminal of Slave #1 to the OUTPUT terminal of Slave
#2, and COMMON terminal of Slave #2 to the OUTPUT terminal of Slave #3

Connects the PAR/SER CONTROL - IN ports of the Master and Slave #3

1

together to provide control signals needed to establish a series-parallel con­figuration

Provides control signals required for series operation.

2

Provides communication between master and three slaves comprised of two

1

series-connected units arranged in 2 parallel branches.

http://www.kepcopower.com  email: [e-mail]

228-1524 REV 3 033012

118-1155

118-1112

118-1158

118-1120

118-1149

TABLE 2. EQUIPMENT SUPPLIED (CONTINUED)

Item Quantity Purpose Kepco Part Number

Protection Cable (1 ft.) 3 Provides interlock protection signals required for multiple unit operation. 118-1126

Protection - OUT

Termination (Slave)

Protection - IN

Termination (Master)

Chassis Ground Cable 2 Connects chassis ground terminals of all units. 118-1272

Ground Cable mounting

hardware

Output Sense Cable 2 Connects Output sense terminal to Common sense terminal of next unit. 118-1271

Nut 2

Instruction Manual 1 Lists material supplied and specifications for multiple unit combination. 228-1524

4 sets Each set consists of eight parts, mounted in the following order: No. 10 star

Provides proper termination for the slave connection to the Protection

1

Cable.

Provides proper termination for the master connection to the Protection

1

Cable.

lockwasher P/N 103-0106 (at chassis), No. 10 flat washer P/N 103-0031,
No. 10 split lockwasher P/N 103-0033, 10-32X3/8 nut P/N 102-0008, No. 10
flat washer P/N 103-0031, [lug(s) from ground cable], No. 10 flat washer P/N
103-0031, No. 10 split lockwasher P/N 103-0033, and 10-32X3/8 nut P/N
102-0008.

Overcomes tight space for output cable connections. After securing bottom
cable to output terminal stud using one nut, additional cables can be ori­ented for best layout and secured with separate nut.

195-0108

195-0107

(See

Purpose

at left for part

numbers)

102-0046

TABLE 3. MODEL PARAMETERS FOR 2 X 2 CONFIGURATION OF FOUR (4) IDENTICAL BOP 1000W UNITS

(2 SERIES-CONNECTED UNITS X 2 PARALLEL BRANCHES)

(4) Identical Models

(2 Series x 2 Parallel)

BOP 6-125MG ±12V d-c ±250A d-c 1.2 25.0

BOP 10-75MG ±20V d-c ±150A d-c 2.0 15.0

BOP 20-50MG ±40V d-c ±100A d-c 4.0 10.0

BOP 25-40MG ±50V d-c ±80A d-c 5.0 8.0

BOP 36-28MG ±72V d-c ±56A d-c 7.2 5.6

BOP 50-20MG ±100V d-c ±40A d-c 10.0 4.0

BOP 72-14MG ±144V d-c ±28A d-c 14.4 2.8

BOP 100-10MG ±200V d-c ±20A d-c 20.0 2.0

d-c Output Range Closed Loop Gain

E

O Max

I

O Max

Voltage Channel

(V/V)

Current Channel

TABLE 4. GENERAL SPECIFICATIONS FOR BOP 1000W 2 X 2 CONFIGURATION

(2 IN SERIES, 2 PARALLEL BRANCHES)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 38A a-c maximum

264 Va-c 25.6A a-c maximum

Leakage current 14.0mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

Programming
resolution/accuracy

Readback
resolution/accuracy

Voltage 14 bits / 0.2% 2% accuracy for Ext Ref Level. Unit gain

Current

Voltage Limit 12 bits / 0.5%

Current Limit 12 bits / 0.5%

Voltage 16 bits / 0.2% main or limit channel

Current 16 bits / 0.5% main or limit channel

14 bits / 0.5%

adjustable between 0 and E
or I

ONOM

/10 (current).

(A/V)

ONOM

/10 (voltage)

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1524 REV 3 033012