How it Works
Kenwood
Loading...
KTF-2010
Service manual
20 pgs1.55 Mb0
User Manual
20 pgs294.99 Kb0
User Manual
21 pgs325.58 Kb0
Table of contents
Loading...

Kenwood KTF-2010, KTF-3010 User Manual

Download
Page 1
FM/MW/L W TUNER
KTF-2010 KTF-3010
INSTRUCTION MANUAL
KENWOOD CORPORATION
B60-3703-00 00 MA ( E2, T ) 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 1
OC
Page 2

Before applying power

Units are designed for operation as follows.
Europe , U.K. and Russia ......................................................... AC 230 V only
operation.
KTF-3010/KTF-2010 (En)
For the United Kingdom
Factory fitted moulded mains plug
1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS 1362) fuse.
2.The fuse cover must be refitted when replacing the fuse in the moulded plug.
3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
IMPORTANT
Caution : Read this page carefully to ensure safe
The wires in the mains lead are coloured in accordance with the following code.
Do not connect those leads to the earth terminal of a three-pin plug.
Blue : Neutral Brown : Live

Safety precautions

WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALER T THE USER TO THE PRESENCE OF UN INSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MA Y BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPOR­TANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE, REFER SER VICING TO QUALIFIED SERVICE PERSON­NEL.

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay . Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Accessories

FM indoor antenna (1) AM loop antenna (1) Loop antenna stand (1) Audio cord (1) System control cord (1)
Page 3

Special features

ACTIVE RECEPTION (A.R.) (KTF-3010 only)
When the receiving frequency changes by a tuning operation or recalling a preset station, the tuner automatically switches the IF BAND, RF ATT and ANT A/B functions to obtain the optimum reception conditions for the signals being received.
RDS (Radio Data System) & EON(Enhanced Other Network) reservation
The RDS makes it possible to select stations according to their program types (PTY search) and to display the station names. Moreover, the RDS automatic memory function which stores up to 40 RDS stations automatically in the memory is featured. This function checks the RDS data when storing stations in the memory to avoid storing stations which are broadcasting the same program simultaneously. In addition, by using the EON function which administers the information of other stations, you can reserve the desired information such as traffic announcement, news and so on, even though these types of programs are not currently broadcast. While listening to a station which makes the EON indicator light, the tuner automatically selects the station which starts broadcasting the program of the desired information. When the program of the desired information ends, the tuner automatically returns to the previous program. If this tuner is connected to a KENWOOD amplifier with the system control cord, the amplifier automatically switches the input source to the tuner input when the program of the reserved information starts, even when you are listening to the input source other than the tuner.
KTF-3010/KTF-2010 (En)
STATION PRESET
This unit features a function which stores the broadcast station you are listening to with easy operations and allows you to store a name for the station. It is very convenient to register the desired stations. Also, you can recall the stations with easy operations.

Contents

Before applying power ................................................................................................................................................................. 2
Special features ........................................................................................................................................ 3
System connection ................................................................................................................................................................. 4
Controls and indicators ................................................................................................................................................................. 6
Useful functions for broadcast reception ................................................................................................................................................................. 7
Broadcast reception ................................................................................................................................................................. 8
Receiving a broadcast station (other than RDS stations)..........................................................................8
RDS (Radio Data System) ................................................................................................................................................................. 9
Storing broadcast stations in memory ............................................................................................................................................................... 10
Receiving a preset station ............................................................................................................................................................... 11
Entering broadcast station names ............................................................................................................................................................... 12
PTY search ............................................................................................................................................................... 13
EON reservation ............................................................................................................................................................... 15
In case of difficulty ...............................................................................................................................................................16
Specifications ............................................................................................................................................................... 17
Caution : Read the pages marked carefully to ensure safe operation.
Before applying power.......................................................................................................................2
Safety precautions .............................................................................................................................2
Page 4

System connection

KTF-3010/KTF-2010 (En)
Connection of the Audio components/Connection of the system control cord
Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Do not plug in the power lead until all connections are com­pleted.
Caution regarding placement
To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.
Left and right panels: 10 cm Rear panel: 10 cm
Malfunction of microcomputer
If operation is not possible or erroneous display ap­pears even though all connections have been made properly, rest the microcomputer referring to "In case of difficulty". ^
ANTENNA
FM 75Ω
TUNER
L
R
Audio cord
OUTPUT
AM
GND
BA
L
R
Pre-main amplifier
STEREO INTEGRATED AMPLIFIER KAF-3010R
ON/STANDBY
POWER
ON OFF
PHONES A SPEAKER B BASS TREBLE BALANCE
|{ |{
SYSTEM
CONTROL
ƒ
SL16 XS 8
LR
INPUT SELECTOR
MDTAPETUNERPHONOCD
VOLUME CONTROL
SOURCE DIRECT
MIN MAX
MUTING LOUDNESS
thermally reactive advanced instantaneous transistor TRAIT
System control cord
SYSTEM CONTROL
ƒ
SL16 XS 8
To wall AC outlet
No matter to which of the two terminals the con-
KTF-3010 only
nection is made, the use method is the same.

The system control connection

Connecting system control cords after connecting a Kenwood audio component system lets you take advantage of convenient system control operations. There are two Kenwood system control modes. Make connections according to the groups of terminal symbols shown below.
[SL16] Mode :for
terminals only
[XS8] Mode : lets you combine F, f, and ƒ terminals
This unit is compatible with both [SL16] and [XS8] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow the instructions in “Switching from [SL16] to [XS8]”.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system
Notes
Notes
operations. If your equipment consists of this kind of combination, please do not connect any system control cords. Even without system control cords, normal operations can be carried out without affecting performance.
2. If your amp or receiver does not have a system control terminal, do not connect any system control cords to the system control terminals on the other components.
3. Do not connect system control cords to any components other than those specified by Kenwood. It may cause a malfunction and damage your equipment.
4. Be sure the system control plugs are inserted all the way in to the system control termi­nals.
1.Connect all cords firmly. If connections are loose, you may lose the sound or interconnectable system control operations may not work.
Notes
Notes
2.When plugging and unplugging connection cord, be sure to first remove the power cord from the AC outlet. Plugging / unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit.
Page 5
KTF-3010/KTF-2010 (En)
The system control operations
Remote Control
Lets you operate this unit with the system remote supplied with the amp or receiver.
Automatic Operation (except [XR] equipment)
Automatically switches the input selector on the amp when you operate one of the tuning keys on this unit.
Automatic EON reception
Even if the input selector on the amp is set to a source other than tuner , the amp will automatically switch to tuner when an EON broadcast you are waiting for is received. When using equipment connected in the [SL16] mode, the amp will switch back to the original input source when EON broadcast has finished. %
Switching from [SL16] to [XS8]
Use the rear panel switch to switch to the system control [XS8] and [SL16] modes. Do this operation after completing all connections.
÷ Remove the AC power cord plug from the wall outlet before switching modes. ÷ This operation will not affect items stored in the memory.
SL16 XS 8
j

Connection of antenna

Do not plug in the power lead until all connections are completed.
Connection method to each antenna terminal
1 Push lever 2 Insert cord 3 Return lever
FM indoor antenna connection
The accessory antenna is for temporary indoor use only. For stable signal reception we recommend using an outdoor antenna. Remove the indoor antenna if you connect one outdoors.
FM 75Ω
ANTENNA
The figure shows an example for the KTF-3010
If there is only one antenna, connect it to side A of the antenna terminal.
ANTENNA
FM 75Ω
OUTPUT
AM
GND
L
BA
R
SL16 XS 8
SYSTEM
CONTROL
ƒ
FM outdoor antenna connection
Lead the 75 Ω coaxial cable connected to the FM outdoor antenna into the room and
Use a commercially available antenna adaptor.
AM
GND
BA
connect it to the FM 75 Ω terminal.
AM loop antenna connection
The supplied antenna is for indoor use. Place it as far as possible from the main system, TV set, speaker cords and power cord, and set it to a direction which provides the best reception.
In certain areas, FM broadcast can be received by connecting the antenna cable to a wall antenna terminal (CATV antenna socket, etc.).
Page 6

Controls and indicators

KTF-3010/KTF-2010 (En)
AR indicator (KTF-3010 only)
STANDBY indicator
RDS indicator
RDS EON
Signal indicator
EON indicator
The figure shows an example for the KTF-3010
12
AM
-
FM STEREO SYNTHESIZER TUNER
RECEPTION IF BAND
ON/STANDBY
TA/NEWS
3
ACTIVE
PTY/
PTY SEARCH
4
TA indicator
AR
MW
LW FM
Receiving band indicator
5
6
HIGHBLEND
KTF-3010
WIDE
NARROW
ANT A/B
RF ATT
DISPLAY
RFATT
MEMORY
PTY indicator
TP indicator
NEWS indicator
MEMORY indicator
Antenna A/B indicator (KTF-3010 only)
********.
Frequency display, Preset channel display STATION NAME display
Display
AUTO/MANUAL with the KTF-2010
7
1
2
8
9
3456789
0
TUNING
MODE
+
10
/CLEAR
Megahertz indicator
0/CHARA
STEREOSTANDBY ANT A BMEMOPTYTPNEWSTA
TUNED AUTO kHz MHz
Kilohertz indicator
!
BAND
P. CALL
DOWN UP
Tuning mode indicator
TUNED indicator
Reception mode indicator
@
TUNING/MULTI CONTROL
%$#
^
&
*
KTF-3010 only
1 ON/STANDBY key 8
Press to turn on/off(STANDBY) the power.
2 ACTIVE RECEPTION key (KTF-3010 only)
7
Press to obtain the optimum reception con­ditions for the signals being received.
3 IF BAND key (KTF-3010 only) (available for
the FM band only) 7 Press to switch the intermediate frequency pass band between WIDE (wide band) and NARROW (narrow band).
4 RF ATT key (KTF-3010 only) 7
Press to minimize the RF reciprocal modula­tion and mixed modulation distortion when there is an adjacent channel with strong ra-
5 ANT A/B key (KTF-3010 only)
7
Press to select the antenna when using 2 antennas.
6 HIGH BLEND indicator (KTF-3010 only)
7
7 WIDE indicator (KTF-3010 only)
7
8 NARROW indicator (KTF-3010 only)
7
9 RF ATT indicator (KTF-3010 only) 7 0 AUTO/MANUAL key (KTF-2010)
TUNING MODE key (KTF-3010)
Press to select the tuning mode.
! BAND key
Press to switch the broadcast band.
7
8
@ TUNING/MULTI CONTROL knob
80!@#
Used for tuning broadcast stations, select­ing program type and entering characters.
# TA/NEWS key $ PTY/PTY SERCH key # % DISPLAY key 9 ^ MEMORY key 0@
Used for storing broadcast stations and entering station names.
& Numeric keys
0!@#
Used for storing and calling up broadcast stations and entering station names.
* P.CALL key
Press to recall a preset station.
%
!@
dio waves.
STANDBY mode of POWER switch
When the power cord of this unit is plugged into an AC outlet, the STANDBY indicator lights up while the power is off. This indicates that a small amount of current is being supplied to the unit to back up the memory contents even when the power is turned off.
Page 7

Useful functions for broadcast reception

Each time the key is pressed, the operation mode changes.
ACTIVE RECEPTION (A.R) key (KTF-3010 only/ available for the FM band only)
Flashes, then lights
AR
FM
--
ACTIVE
RECEPTION
When you press the ACTIVE RECEPTION key, the AR indicator flashes, and the tuner will automatically switch the IF BAND, RF ATT and ANT A/B functions to select the best conditions for recep­tion. If, at this time, you change the receiving frequency by adjust­ing the tuning UP/DOWN or calling up preset broadcast stations, you will always achieve optimum broadcast wave reception. Normally leave the ACTIVE RECEPTION mode ON. During manual operation of IF BAND, RF ATT and ANT A/B func­tions, the ACTIV RECEPTION mode is set to OFF.
KTF-3010/KTF-2010 (En)
IF BAND key (KTF-3010 only /available for the FM band only)
One or the other lights
HIGHBLEND
WIDE
NARROW
RFATT
IF BAND
RF ATT key (KTF-3010 only /available for the FM band only)
HIGHBLEND
WIDE
NARROW
RFATT
Light up when the switch is turned on.
RF ATT
ANT A/B key (KTF-3010 only /available for the FM band only)
One or the other lights
9 8)).
STEREOANT A B
TUNED
AUTO MHz
ANT A/B
This function lets you set the intermediate frequency pass band to WIDE (wide band), or NARROW (narrow band).
WIDE: Normally set the IF BAND to WIDE. This setting allows
reception of good quality sound with minimal distortion.
NARROW: If signal reception is poor due to interference from a neigh-
bouring station when the IF BAND is set to WIDE, change the IF BAND setting to NARROW.
If the ACTIVE RECEPTION mode is set to ON, WIDE or NARROW will
be switched over automatically.
When there is an adjacent channel with strong radio waves, RF reciprocal modulation, mixed modulation distortion easily occurs. By switching the RF ATT key ON the RF reciprocal modulation and mixed modulation can be minimized.
Even when the key is set to OFF, if the ACTIVE RECEPTION mode is ON, it will work automatically.
When using 2 exterior antennas, or, an external antenna with an already established antenna (cable broadcast reception antenna etc.), aligning to the respective set up and reception statuses, A or B can be switched.
If the ACTIVE RECEPTION mode is set to ON, the key will switch A/ B automatically.
TUNING MODE key (KTF-3010) AUTO/MANUAL key (KTF-2010)
By pressing this key, the automatic stereo function and the auto­matic tuning function are both switched over at the same time when AUTO STEREO or HIGH BLEND (available with KTF-3010 only) is selected.
TUNING
KTF-3010
STEREOANT A
TUNED AUTO
8 9)).
Lights up in the AUTO mode.
Each press switches the turning methods as follows:
1 AUTO/STEREO : AUTO lit (auto tuning)
FM
MW/ LW
2 HIGH BLEND : AUTO lit, HIGH BLEND LED lit
3 MANUAL/MONO : AUTO not lit (manual tuning)
1 AUTO : AUTO lit (auto tuning) 2 MANUAL/MONO : AUTO not lit (manual tuning)
MHz
KTF-2010
(auto tuning)
MODE
AUTO/MANUAL
AUTO/STEREO (STEREO lit during stereo reception): Usually, set the switch to AUTO/STEREO. The tuner automatically switches between stereo and monaural receptions according to the program being received. The tuner automatically scans the frequency and stops when a station is tuned in.
HIGH BLEND (available for the FM band with KTF-3010 only): STEREO lit during stereo reception This function reduces audible noise in the middle band and above when receiving weak radio waves during stereo broadcasts. The tuner automatically scans the frequency and stops when a sta­tion is tuned in.
MANUAL/MONO: Set the switch to OFF when noise interferes due to weak radio waves in the stereo reception. The stereo broadcast is received in monaural and the noise will be reduced. When you want to tune in a station with weak radio waves which the auto tuning func­tion can not pick up, select the manual tuning mode.
Page 8
MHz
ANT A
FM
-- 8 9)).
LW
MW
AUTO MHz
ANT A
AR
-- 8 9)).
FM
TUNED
AUTO MHz
STEREOANT A
AR
FM
-- 9 ))).

Broadcast reception

HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON
This section shows you how to receive radio broadcasts. Y ou can store up to 40 stations in the memory and recall them with a single touch of the key.
Preparation
KTF-3010/KTF-2010 (En)
The figure shows an example for the KTF-3010
Switch the ON/STANDBY key to ON.
: Keys or controls to be used in this operation.

Receiving a broadcast station (other than RDS stations)

Switch the amplifier input to the tuner input.
1
Select the broadcast band.
2
BAND
Select the tuning method.
3
KTF-2010 KTF-3010
AUTO/MANUAL
Make the AR indicator light. (FM band only)
4
TUNING
(KTF-3010 only)
ACTIVE
RECEPTION
MODE
[ ............................................................................................................................ ]
Each press switches the band as follows:
1 FM 2 MW 3 LW (U. K. only)
“FM”, “MW” or “LW” is displayed.
[ ............................................................................................................................ ]
The tuner switches over as follows each time you press the key while receiving a FM broadcast.
1 AUTO/STEREO : AUTO lit (auto tuning) 2 HIGH BLEND : AUTO lit, HIGH BLEND LED lit (auto tuning)
(available for the FM band with KTF-3010 only)
3 MANUAL/MONO : AUTO not lit (manual tuning)
÷ Usually, set the switch to AUTO (auto tuning).
Select HIGH BLEND (available with the KTF-3010 only) or MANUAL when the radio waves are weak and there is a lot of noise interference.(The stereo broadcasting is received in monaural dur­ing manual tuning.)
[ ............................................................................................................................ ]
Each time the ACTIVE RECEPTION key is pressed, the setting changes.
1 ON (AR indicator lit ): when switching the IF BAND, RF ATT and
ANT A/B functions automatically.
2 OFF (AR indicator not lit ):
when switching these functions manually.
5
Select a station.
To decrease frequency
TUNING/MULTI CONTROL
DOWN UP
÷ Usually, set ACTIVE RECEPTION key to ON. ÷ FM broadcasts are received in the optimum reception conditions.
[ ............................................................................................................................ ]
"TUNED" lights up when a station is tuned.
To increase frequency
Auto tuning : The next station found is tuned automatically.
Frequency display
Manual tuning : Keep turning the knob, checking the display, until you
tune in on a station.
Page 9

RDS (Radio Data System)

TUNED
AUTO MHz
STEREOANT A
AR
RDS
FM
-- 9 25).
TUNED
AUTO
STEREOANT A
AR
RDS
FM
BACEDFGH
TUNED
AUTO MHz
STEREOANT A
AR
RDS
FM
-- )125).
TUNED
AUTO
STEREOANT A
AR
RDS
FM
P M1 234:
TUNED
AUTO
STEREOANT A
AR
RDS
FM
BBC1 FM
KTF-3010/KTF-2010 (En)
RDS is a system which transmits useful information (digital data) for FM broadcasts together with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions such as automatic display of the station name.
This unit is equipped with the following functions utilizing RDS data: (Be sure to set the automatic memory function - otherwise, the RDS function will not work.)
RDS Auto Memory function
RDS stations and FM station are automatically selected and stored in the memory (up to 40 stations).
PTY (Program Type Identification) Search (FM band)
The tuner automatically searches for a station which is currently broad­casting a specified program type (genre).
EON (Enhanced Other Network) reservation
When you select one or two of the types of information beforehand, the tuner automatically switches to the station which is broadcasting the program of the reserved information even though you are listen­ing to another station. When the program of the reserved information ends, the tuner returns to the previous station.
RT (Radio Text) indicator: (See below.)
Some RDS stations transmit the text data.
PS (Program Service Name) Display: (See below.)
When an RDS broadcast is received, the station name is automati­cally displayed.
CT (Clock Time) Display: (See below.)
Some RDS stations transmit clock data along with the broadcast sig­nal. RT, PS, and CT can be selected with the DISPLAY key. The display may not light, depending on the RDS broadcast station.
0
#
%
The RDS indicator lights up when an RDS broadcast (signal) is received.
* Some functions may not be provided or be given different names
depending on countries or areas.

DISPLAY key

Pressing the DISPLAY key changes the display contents.
DISPLAY
Display mode priority ranking
When an RDS broadcasts is received.
When other than RDS broadcasts is received
When the MW or LW band is received.
1 PS (Program Service name) indicator 2 RT (Radio Text) indicator 3 CT (Clock Time) indicator 4 Frequency indicator
1 STATION NAME indicator
or "NO PS" indicator
2 "NO RT" indicator 3 "NO CT" indicator 4 Frequency indicator
1 STATION NAME indicator
or "NO TITLE" indicator
2 Frequency indicator
1 PS (Program Service name) Display:
When an RDS broadcast is received, the station name is auto­matically displayed. If no PS data was sent,
2 RT (Radio Text) Display:
When text data is received after 'RT' flashes in RDS broadcast re­ception, text appears in the display scrolling from right to left (up to 64 characters).
3 CT (Clock Time) Display:
The hours and minutes are displayed after "CT" flashes in RDS broadcast reception.
4 Frequency Display:
The frequency of the current station is displayed.
"NO PS" is displayed.
Page 10

Storing broadcast stations in memory

HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON
TUNED AUTO
kHz
MHz
STEREOSTANDBY ANT A BMEMO
AR
1089))
AM
FM
KTF-3010/KTF-2010 (En)
The figure shows an example for the KTF-3010
10
The automatic memory function allows you to store up to 40 stations using only one button. The manual preset function allows you to store stations one at a time.
Use the automatic memory function first.
: Keys or controls to be used in this operation.

AUTO MEMORY (Storing stations automatically in memory )

The AUTO MEMORY function automatically calls up only those stations which have RDS broadcasts for storing (up to 40 stations can be stored).
1 Switch to FM band. 2 Press and hold the MEMORY key (for more than 2 seconds).
MEMORY
The tuner completes the scanning of frequencies in 5 minutes. While scanning, "AUTO" and "MEMORY" are displayed in turn.
÷ Unless stations are stored with the automatic memory function, EON
reservation and PTY search will not work.
÷ AR will not work when the automatic memory function is on. ÷ Broadcast stations stored manually may be overwritten. ÷ Stations already stored in the preset memory may be replaced by RDS
stations. (i.e., If the RDS AUTO MEMORY function finds 15 RDS sta­tions, the stations currently preset at numbers 01- 15 are replaced by the RDS stations.)
÷ If the antenna is replaced, you will have to reset the automatic memory
function.
÷ Stored stations may be erased from the memory.

MANUAL PRESET(Storing stations one at a time)

Tune in the station to be preset
1
Press the MEMORY key
2
If you press the MEMORY key when the preset number dis­played is "
Select one of the preset numbers from 1 to 40.
3
Press the numeric keys (0 to 9, +10) in the following order.
To select “15”...0,5 To select “20”...0,0, )
", the smallest unstored number appears.
- -
1 Turn the TUNING/MULTI CONTROL knob.
DOWN UP
2 Select the desired station.
Instead of steps 1 and 2, you can use the numeric keys (0~9,+10), to store the broadcast stations.
MEMORY
TUNING/MULTI CONTROL
MEMORY
Perform the operations in the five seconds that the display is blinking.
Lights (for 5 sec.)
(If more than 5 sec. have elapsed, press the MEMORY key again.)
Blinks Lights (for 5 sec.)
AR
FM
51 9) )).
The numbers 1 to 40 appear, in turn, as you turn the knob.
02
,
,
03 39,4038
01
÷ Repeat steps 1 to 3 for each of the stations to be stored in memory. ÷ If a station is stored in a preset number which already stores a station
memory under it, the previous memory is replaced by the new memory content.
÷ Once the memory content has been preset, it is held for about 3 days
even after the power cord is unplugged from the mains outlet.
÷ You cannot enter numbers over 40. ÷ If you make a mistake when pressing the 0 key, press the 0
key several times to return to the original display before re-entering.
÷ The stored station will be erased from the memory.
,
STEREOANT AMEMO
TUNED
AUTO MHz
Page 11

Receiving a preset station

HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON
TUNED AUTO
kHz
STEREOSTANDBY ANT A BMEMO
AR
5PCLAL0
AM
FM
TUNED AUTO
kHz
MHz
STEREOSTANDBY ANT A B
AR
629)))
.
AM
FM

Receiving a preset station

Set to the Call up (Sellect) mode.
1
P. CALL
Select one of the preset numbers.
2
TUNING/MULTI CONTROL
KTF-3010/KTF-2010 (En)
The figure shows an example for the KTF-3010
11
: Keys or controls to be used in this operation.
÷ Press P.CALL key once more to cancel the call up mode and return to
the original display.
[ ............................................................................................................................ ]
Blinks for 5 sec.
DOWN UP
When you stop turning the knob, you tune in on the preset station.
Instead of steps 1 and 2, you can use the numeric keys (0~9,+10), to store the broadcast stations.
Press the numeric keys (0 to 9, +10) in the following order.
To select “15”...0,5 To select “20”...0,0, )
÷ While the display is blinking, you can select the next station. ÷ If the tuner has stored a preset station name or program service name,
each will be displayed.
÷ You cannot enter numbers over 40. ÷ If you make a mistake when pressing the 0 key, press the 0
key several times to return to the original display before re-entering.
Memory back up
Even if the power cord is unplugged from the AC outlet, the preset memory contents will be backed up for 3 days.
Last channel memory
When the power is turned ON or the BAND key is pressed to switch the band, the last station previously received is auto­matically tuned in.
Page 12
HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON

Displaying broadcast station names

TUNED AUTO
kHz
MHz
STEREOSTANDBY ANT A B
AR
8)89))
AM
FM
TUNED AUTO
kHz
MHz
STEREOANT A BB
AR
1
-
89 00;
AM
FM
TUNED AUTO
kHz
STEREOSTANDBY ANT A BMEMO
AR
BA1+2
-
00;
AM
FM
12
Preparation
Switch the ON/STANDBY key to ON.

Entering broadcast station names

Call up (select) the preset station.
1
Follow the steps in "Receiving a preset station" to call up stored stations with no PS display, MW stations and LW sta-
tions.
!
KTF-3010/KTF-2010 (En)
The figure shows an example for the KTF-3010
: Keys or controls to be used in this operation.
Select the Entry mode.
2
Press the 0/CHARA. key
Enter the characters.
3
789
0
/CHARA.
1 Select the characters and symbols using
the TUNING/MULTI CONTROL knob.
TUNING/MULTI CONTROL
DOWN UP
2 Press the 0/CHARA. key to confirm the
characters. The cursor will move to allow the next entry.
789
0
/CHARA.
[ ............................................................................................................................ ]
÷ The entry mode will be cancelled unless the next steps are completed
within 10 seconds.
÷ The station name cannot be entered if "PS" is displayed.
[ ............................................................................................................................ ]
You can select from the following characters and symbols.
A,B,C.....X,Y,Z,0,1,2,3.....8,9,+,-, ,/
[
,
*
Space
The selected characters will blink.
Enter up to 8 characters.
3 Repeat steps 1 and 2.
4 Press the MEMORY key to confirm entry.
MEMORY
÷ To correct the characters, before pressing the MEMORY key, press
the 0/CHARA. key several times to make the character that needs correcting flash, then re-enter the character.
÷ If only spaces are entered, a station name will not be stored. ÷ To delete all entered characters, press the +10/CLEAR key in the
entry mode.
÷ If you press the DISPLAY key after entering the name of the broadcast
station, the entered station name and frequency will be displayed in turn. (if none has been entered "NO TITLE" will appear).
Page 13
HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON
0
TUNED AUTO
kHz MHz
STEREOSTANDBY BMEMO
RDS
ENW*S***;
AM
TA
NEWS TP PTY
EON
FM
AR

PTY search

By specifying the type of program (genre) you want to listen to, the tuner automatically searches for a station which is currently broad­casting a program of the specified type.
With certain receiving conditions, if may take more than 1 min­utes until the search completes.
KTF-3010/KTF-2010 (En)
The figure shows an example for the KTF-3010
13
Preparation
: Keys or controls to be used in this operation.
÷ Set the RDS to AUTO MEMORY mode. ÷ Set the broadcast band to FM.

Searching for a desired program type (PTY search)

Select the PTY search mode.
1
PTY/
PTY SEARCH
Select the desired program type.
2
Use program type table on the right for your convenience.
A When selecting with the TUNING/
MULTI CONTROL knob.
Select while "PTY" is lit.
TUNING/MULTI CONTROL
DOWN UP
B When selecting with the numeric keys
(0 - 9, +10).
1
3456789
2
With the TUNING/MULTI CONTROL knob, the desired program type among 29 program types is selected in the order.
When an RDS broadcast is received, the program type is shown on the display. If no PTY data is available, or if the station is not an RDS station,
"NONE" is displayed.
[ ............................................................................................................................ ]
Program type table
ABProgram type table Display
DOWN
▲
▼
UP
1
Pop Music
2
Rock Music
3
*M.O.R. Music
4
Light Classical
5
Serious Classical
6
Other Music
7
News
8
Current Affairs
9
Information
0
Sport
10
Education
11
Drama
12
Culture
13
Science
14
Varied Speech
15
Weather
16
Finance
17
Children's Programmes
18
Social Affairs
19
Religion
20
Phone in
21
Travel
22
Leisure
23
Jazz Music
24
Country Music
25
National Music
26
Oldies Music
27
Folk Music
28
Documentary
*M.O.R. Music (Middle of the Road Music)
POP M ROCK M M. O. R. M LIGHT M CLASSICS OTHER M NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED WEATHER FINANCE CHILDREN SOCIAL A RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT
Page 14
14
PTY
ORC KM
PTY
ORC KM
TUNED
AUTO
STEREOANT A
AR
RDS
FM
BBC1 FM
PTY
Start the search.
3
KTF-3010/KTF-2010 (En)
When searching for a Rock Music broadcast.
PTY/
PTY SEARCH
To change to a different program type:
Repeat steps 1, 2, 3.
Display with the tuner is searching
Program type name display.
When a station is received.
When a station is confirmed.
Station name display.
÷ No sound is heard while "PTY" is blinking. ÷ If a program of the desired type cannot be found,
then after several seconds the display returns to the original display.
÷ When the program type is found, the tuner starts receiving - the type
name display flashes and after a few seconds, it changes to the station name display.
÷ Press the PTY key again during PTY search to cancel the function.
Blinks
Blinks Goes off
"NO PROG" is blinked,
Page 15
HIGHBLEND
WIDE
NARROW
RFATT
TUNING
MODE
+10/CLEAR
1
ACTIVE
RECEPTION IF BAND
RF ATT
TA/NEWS
PTY/
PTY SCARCH
DISPLAY
ANT A/B
MEMORY
AM
-
FM STEREO SYNTHESIZER TUNER
KTF-3010
BAND
P. CALL
DOWN UP
TUNING/MULTI CONTROL
3456789
0/CHARA.
2
ON/STANDBY
R D S
EON
TUNED
AUTO MHz
STEREOANT A
AR
FM
BBC9 8)).
RDS
TA
TP
EON

EON reservation

By using the EON function which administers the information of other
KTF-3010/KTF-2010 (En)
stations, you can reserve the desired information such as traffic an­nouncement, news and so on, even though these types of programs
The figure shows an example for the KTF-3010 are not currently broadcast. While listening to a station which makes the EON indicator light, the tuner automatically selects the station which starts broadcasting the program of the desired information. When the program of the desired information ends, the tuner auto­matically returns to the previous program.
Preparation
÷ Set the RDS to AUTO MEMORY mode.
: Keys or controls to be used in this operation.
÷ Set the broadcast band to FM.

Reserving the desired information (EON reservation)

Proceed the steps in “Storing broadcast
1
stations in memory ”. 0
Tune in an RDS station (EON).
2
[ ............................................................................................................................ ]
If the RDS automatic memory function is already set, skip this procedure.
÷ If all the 40 stations are MANUAL PRESET according to the procedure
in "Storing broadcast stations in memory", the EON function will not work. Be sure to use the RDS automatic memory function.
Lights up
15
Proceed the steps in "Receiving a preset station" !
Select the desired information.
3
TA/NEWS
÷ During TA or NEWS reception, "NOW TA", or "NOW NEWS" will be
displayed.
÷ If TA or NEWS can not be selected, proceed the RDS automatic
memory function again. 0
Wait for the program of the desired informa-
4
tion.
As long as the power is turned on with the program which makes the EON and RDS indicators light tuned in, the tuner waits for the program of the desired information to start.
Indication when “TA” is selected.
[ ............................................................................................................................ ]
Each time the key is pressed, the setting changes.
1 OFF (EON cancelled.) 2 TA (Traffic Announcement) 3 NEWS (News : Program Type) 4 TA/NEWS (Standing by to receive either the TA or NEWS)
[ ............................................................................................................................ ]
÷ If you wish to cancel TA/NEWS while listening to a EON reservation
broadcast, press the TA/NEWS key.
÷ If you press the BAND key while receiving the broadcast of your choice,
EON reservation will be cancelled.
÷ Even if you switch over the input selector of the amplifier connected
with the system control cord while receiving the broadcast of your choice, EON reservation will not be cancelled.
÷ When a EON reservation broadcast is received, the ACTIVE RECEP-
TION will not work. RF ATT functions will be turned OFF.
TP (Traffic Program) indication
When the "TP" indicator is lit, this means that the presently received station or a station in the same network is transmitting traffic information. When "TP" is displayed for the station being received, the traffic information of this station can be received without EON reservation.
Page 16
KTF-3010/KTF-2010 (En)
16
When the amplifier and the tuner are connected with the system control cord 4
Even if the input selector of the amplifier is connected to the source other than the tuner, the input selector of the amplifier switches to the tuner when the desired program starts in the EON reservation mode. Combined with the [SL16], the input selector returns to the original source after the desired program finishes, however , with a [XS8] it will not.

In case of difficulty

What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative.
Operation to reset
The microcomputer may fall into malfunction (impossibility to operate, erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, ex­ecute the following procedure to reset the microcomputer and return it to normal condition.
Symptom Cause Remedy
No sound is heard.
Radio stations cannot be received.
No station is received when a numeric key pressed.
÷ The tuner is not connected to the amplifier.
÷ No antenna is connected. ÷ The broadcast band is not set properly. ÷ The frequency of the desired station is not
tuned.
÷ The ANT A/B key is not set properly
(KTF-3010 only).
÷ The signal detected by the antenna is weak.
÷ No station is preset in the recalled channel. ÷ The preset memory was cleared because the
power cord had been unplugged for a long period of time.
Unplug the power cord from the power socket and, while holding the ON/STANDBY key depressed, plug the power cord into the socket again.
÷ Please note that resetting the microcomputer clears the contents
stored in it and returns it to the condition when it left the factory.
÷ Use audio cords to connect the tuner to the
amplifier.
÷ Connect an antenna. 5 ÷ Set the broadcast band properly. 8 ÷ Tune the frequency of the desired station.
4
8
÷ Set the ANT A/B key properly.
(KTF-3010 only).
÷ If located far from the broadcast station, in-
stall a dedicated FM outdoor antenna (5–6 elements).
÷ Preset the desired station. ÷ Preset the station again. 0
7
0
Interference.
Sound is distorted when the IF BAND is set to NARROW (KTF-3010 only).
Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for they may
Note
Note
deform the plastic components.
÷ Noise due to ignition noise of an automobile.
÷ Noise due to an influence from an electric
appliance.
÷ Noise due to a nearby TV set. ÷ There is a PC nearby.
÷ The broadcasted sound level is too high.
÷ Install the outdoor antenna away from the
road.
÷ Turn off the power of the appliance.
÷
Install the system further apart from the TV set.
÷
Install the system further apart from the PC.
÷ Set the IF BAND to WIDE. 7
Page 17

Specifications

KTF-2010

KTF-3010/KTF-2010 (En)
17
FM tuner section
Tuning frequency range......................... 87.5 MHz ~ 108 MHz
Usable sensitivity (DIN)
MONO.......1.3µV(75 Ω)/13.5 dBf(40 kHz dev., S/N 26 dB)
STEREO .....50µV(75 Ω)/45.2 dBf(46 kHz dev., S/N 46 dB)
Limiting level (DIN) ................................ 1.0µV(75 Ω)/11.2 dBf
Total harmonic distortion (DIN at 1 kHz)
MONO..............................................0.1 % (65.2 dBf input)
STEREO ...........................................0.3 % (65.2 dBf input)
Signal to noise ratio
(DIN weighted at 1 kHz, 40 kHz dev.)
MONO............................................. 69 dB (65.2 dBf input)
STEREO .......................................... 61 dB (65.2 dBf input)
Stereo separation (DIN)
1 kHz ...........................................................................45 dB
Capture ratio ..................................................................2.0 dB
Selectivity (DIN ±300 kHz) ..............................................60 dB
Image rejection ratio (at 98MHz) ................................... 80 dB
IF rejection ratio (at 98MHz)......................................... 100 dB
Spurious rejection ratio (at 98MHz) ............................ 100 dB
AM suppression ratio ..................................................... 68 dB
Sub carrior suppression ratio (DIN)............55 dB (at 19 kHz)
65 dB (at 38 kHz)
Frequency response
(30 Hz ~ 15 kHz) ....................................... +0.5 dB, –2.0 dB
Output level / impedance (FM at 1 kHz, 75 kHz dev.)
Fixed ............................................................... 0.6 V/1.3 kΩ
MW (AM) tuner section
Tuning frequency range.......................... 531 kHz ~ 1,602 kHz
Usable sensitivity
(at 30 % mod., S/N 20 dB) ....................12 µV/(400 µV/m)
Signal to noise ratio
(at 30 % mod., 1mV input).........................................50 dB
Total harmonic distortion................................................ 0.4 %
Image rejection ratio....................................................... 30 dB
Selectivity .........................................................................30 dB
Output level / impedance
(at 30 % mod., 1mV input).......................... 0.18 V/1.3 kΩ
LW (for U.K. only) tuner section
Tuning frequency range............................. 153 kHz ~ 279 kHz
Usable sensitivity
(at 30% mod., S/N 20 dB) .......................................... 22µV
Signal to noise ratio
(at 30% mod., 1mV input)...........................................47dB
Total harmonic distortion................................................. 0.6%
Image rejection ratio........................................................27 dB
Selectivity .........................................................................33 dB
Output level/impedance
(at 30% mod., 1mV input)............................ 0.18 V/1.3 kΩ
GENERAL
Power consumption..........................................................10 W
Dimensions .........................................W : 440 mm (17-5/16")
H : 94 mm (3-11/16") D : 384 mm (15-1/8")
Weight (net)...................................................... 3.3 kg (7.26 lb)
Note
Note
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed with­out notice.
2. The full performance may not be exhibited in extremely coud location (under a water-freezing temperature).
Page 18
18

KTF-3010

KTF-3010/KTF-2010 (En)
FM tuner section
Tuning frequency range......................... 87.5 MHz ~ 108 MHz
Usable sensitivity (DIN)
MONO
..................1.3µV(75 Ω)/13.5 dBf(40 kHz dev., S/N 26 dB)
STEREO
...................50µV(75 Ω)/45.2 dBf(46 kHz dev., S/N 46 dB)
Limiting level (DIN) ................................ 1.0µV(75 Ω)/11.2 dBf
Total harmonic distortion (DIN at 1 kHz)
MONO................................ 0.08 % (85.2 dBf input, WIDE)
STEREO ............................... 0.2 % (85.2 dBf input, WIDE)
Signal to noise ratio
(DIN weighted at 1 kHz, 40 kHz dev.)
MONO............................................. 70 dB (85.2 dBf input)
STEREO .......................................... 65 dB (85.2 dBf input)
Stereo separation (DIN)
1 kHz .............................................................. 50 dB (WIDE)
Capture ratio ......................................................2.0 dB(WIDE)
Selectivity (DIN ±300 kHz) .................................45 dB (WIDE)
(DIN± 200 kHz) ......................... 55 dB (NARROW)
Image rejection ratio (at 98MHz) ................................... 85 dB
IF rejection ratio (at 98MHz)......................................... 105 dB
Spurious rejection ratio (at 98MHz) ............................ 105 dB
AM suppression ratio ..................................................... 68 dB
Sub carrior suppression ratio (DIN)............55 dB (at 19 kHz)
65 dB (at 38 kHz)
Frequency response
(30 Hz ~ 15 kHz) ....................................... +0.5 dB, –1.5 dB
Output level / impedance (FM at 1 kHz, 75 kHz dev.)
Fixed ................................................................. 0.6 V/600 Ω
MW (AM) tuner section
Tuning frequency range.......................... 531 kHz ~ 1,602 kHz
Usable sensitivity
(at 30 % mod., S/N 20 dB) ....................12 µV/(400 µV/m)
Signal to noise ratio
(at 30 % mod., 1mV input).........................................50 dB
Total harmonic distortion................................................ 0.4 %
Image rejection ratio....................................................... 30 dB
Selectivity .........................................................................30 dB
Output level / impedance
(at 30 % mod., 1mV input)........................... 0.18 V/600 Ω
LW (for U.K. only) tuner section
Tuning frequency range............................. 153 kHz ~ 279 kHz
Usable sensitivity
(at 30% mod., S/N 20 dB) .......................................... 22µV
Signal to noise ratio
(at 30% mod., 1mV input)...........................................47dB
Total harmonic distortion................................................. 0.6%
Image rejection ratio........................................................27 dB
Selectivity .........................................................................33 dB
Output level/impedance
(at 30% mod., 1mV input)............................. 0.18 V/600 Ω
GENERAL
Power consumption..........................................................10 W
Dimensions .........................................W : 440 mm (17-5/16")
H : 94 mm (3-11/16") D : 384 mm (15-1/8")
Weight (net)...................................................... 3.3 kg (7.26 lb)
Note
Note
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed with­out notice.
2. The full performance may not be exhibited in extremely coud location (under a water-freezing temperature).
Page 19
KTF-3010/KTF-2010 (En)
MEMO
19
Page 20
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.
Model Serial Number
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use