Kenwood KMM-X50BT User Manual

KMM-X50BT

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

RADIO 5

USB / iPod 6

AUX 8

Pandora® 9

BLUETOOTH® 9

DISPLAY SETTINGS 14

AUDIO SETTINGS 15

MORE INFORMATION 16

TROUBLESHOOTING 16

INSTALLATION / CONNECTION 18

SPECIFICATIONS 20

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the USB device or iPod/iPhone if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Connector (on the reverse side of the faceplate)

How to read this manual

• Operations are explained mainly using buttons on the faceplate.

•

[XX]

indicates the selected items.

•

( XX)

indicates references are available on the stated page.

BASICS

Faceplate

Volume knob

(turn/press)

Detach button

Display window

Attach

Detach

How to reset

Your preset adjustments will also be erased.

To Do this (on the faceplate) Do this (on the remote control)

Turn on the power

Adjust the volume Turn the volume knob. Press VOL

Select a source

Change the display information

Press B SRC.

• Press and hold to turn off the power.

Press BSRC repeatedly.

Press DISPSCRL repeatedly.

• Press and hold to scroll the current display information.

Remote control (RC-406)

Pull out the insulation sheet when using for the first time.

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or VOL .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( not available )

Remote sensor (Do not expose to bright sunlight.)

ENGLISH |

GETTING STARTED

Cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “CANCELDEMO”

1 Press the volume knob.

[YES]

is selected for the initial setup.

2 Press the volume knob again.

“DEMOOFF” appears.

Set the clock

Press the volume knob to enter

1 2

Turn the volume knob to select

Turn the volume knob to make the settings, then press the knob.

Day Hour Minute

Turn the volume knob to select knob.

Turn the volume knob to select

Press and hold to exit.

To return to the previous setting item or hierarchy, press .

While in clock display screen...

Press and hold DISP SCRL to enter clock adjustment mode

directly.

Then, perform step

4 above to set the clock.

“PRESS” “VOLUMEKNOB”

[FUNCTION]

[CLOCK]

[CLOCK ADJUST]

[CLOCK FORMAT]

[12H]

, then press the knob.

, then press the

[24H]

, then press the knob.

Set the initial settings

Press BSRC to enter STANDBY.

1 2 Press the volume knob to enter 3

Turn the volume knob to make a selection (see the following table), then press the knob.

[FUNCTION]

4 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

AUDIO CONTROL SWITCH PREOUT

SP SELECT OFF/ 5/4/ 6 × 9/6/ OEM

TUNER SETTING PRESET TYPE

SYSTEM KEY BEEP TDF ALARM ON

SOURCE SELECT

PANDORA SRC BUILT-IN AUX

F/W UPDATE

UPDATE SYSTEM/ UPDATE BT

F/W UP xx.xx

REAR/ SUB-W

the line out terminals on the rear (through an external amplifier).

4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.

NORMAL

FM2/ FM3/ MW/ SW1/ SW2). ; button, regardless of the selected band.

OFF.;

ON ON

YES

For details on how to update the firmware, see: www.kenwood.com/cs/ce/

: Selects whether rear speakers or a subwoofer are connected to

: Selects according to the speaker size (5inches or

: Memorizes one station for each preset button in each band (FM1/

:Activates the keypress tone.;

:Activates the alarm if you forget to detach the faceplate when ACC is set to

OFF

:Deactivates.

:Enables PANDORA in source selection.;

:Enables AUX in source selection.;

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated).

MIX

: Memorizes one station for each preset

OFF

:Deactivates.

OFF

:Disables.

( 9)

OFF

:Disables.

( 8)

RADIO

Search for a station

Press BSRC to select TUNER.

1 2 Press BAND repeatedly (or press

select FM1/ FM2/ FM3/ MW/ SW1/ SW2.

3 Press S / T (or press S / T(+) on RC-406) to search for a

station.

• To change the searching method for S / T : Press

repeatedly. AUTO1: Automatically search for a station. AUTO2: Search for a preset station. MANUAL: Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on RC-406).

Change the frequency steps

You can change the frequency step of: FM: 50 kHz to 200 kHz MW: 9 kHz to 10 kHz

1 Press and hold B SRC to turn off the power. 2 While pressing number buttons 1 and 5, press B SRC.

Release your fingers from the buttons after the display appears.

• To restore the initial setting, repeat the same procedure.

• When the frequency step is changed, the previously stored stations in

the memory are deleted.

AM–/#FM+ on RC-406) to

SEEK

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a frequency. 3 Press ENT IW to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

2, Direct Access Tuning

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to make a selection (see the following table),

then press the knob.

3 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

TUNER SETTING LOCAL SEEK

AUTO MEMORY YES

MONO SET

NEWS SET ON

REGIONAL ON

AF SET ON

:Searches only MW/ SW1/ SW2 stations with good reception.;

OFF

:Cancels.

:Automatically starts memorizing 6 stations with good reception.;

:Cancels. (Selectable only if

( 4) ON

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

:The unit will temporarily switch to News Programme if available.;

OFF

:Cancels.

:Switches to another station only in the specific region using the “AF”

control.;

OFF

:Cancels.

:Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

[NORMAL]

OFF

is selected for

:Cancels.

[PRESETTYPE]

ENGLISH |

RADIO

USB / iPod

TI ON

PTY SEARCH

CLOCK TIME SYNC

•

[MONO SET]/ [NEWS SET]

only when the band is FM1/ FM2/ FM3.

• Available Program Type:

SPEECH

: NEWS

MUSIC: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),

The unit will search for the Program Type categorized under

[MUSIC]

• If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin function is turned on.

:Allows the unit to temporarily switch to Traffic Information.;

OFF

:Cancels.

Press the volume knob to enter PTY language selection. Turn the volume knob to select the PTY language ( press the knob. Selects the available Program Type (see the following), then, press

S / T

ON OFF

, AFFAIRS

SCIENCE IN

, TRAVEL

CLASSICS FOLK M (music)

if selected.

to start.

:Synchronizes the unit’s time to the Radio Data System station time.;

:Cancels.

/ [

REGIONAL]/ [AF SET]/ [TI]/ [PTY SEARCH]

, INFO (information), SPORT

, VARIED

, WEATHER

, LEISURE

, DOCUMENT

, OTHER M (music), JAZZ

ENGLISH/ FRENCH/ GERMAN

, FINANCE

, CHILDREN

, COUNTRY

, EDUCATE

, SOCIAL

, NATION M (music), OLDIES

is selectable

, DRAMA

, RELIGION

[SPEECH]

), then

, CULTURE

, PHONE

Start playback

The source changes automatically and playback starts.

USB

USB input terminal

CA-U1EX (max.: 500mA) (optional accessory)

and/ or

USB cable from the rear of the unit

iPod/iPhone

Press 5 iPod to select the control mode while in iPod source.

MODE ON: MODE OFF:

If you connect the iPod/iPhone to the USB input terminal of the unit (while listening to TuneIn Radio, TuneIn Radio Pro or Aupeo), the unit will output the sound from these apps.

USB input terminal

USB cable from the rear of the unit

From the iPod

From the unit.

and/ or

KCA-iP102 (optional accessory) or accessory cable of the iPod/iPhone

To Do this

Pause or resume

Press 6 IW (or press ENT IW on RC-406).

playback

Select a file

Select a folder

Reverse/

Press S / T (or press S / T(+) on RC-406).

Press / (or press

AM– / #FM+ on RC-406).

Press and hold S / T (or press and hold S / T(+) on RC-406).

Fast-forward

Repeat play

Press 4 repeatedly.

• MP3/WMA/WAV/FLAC file or iPod: FILEREPEAT, FOLDERREPEAT, REPEATOFF

• KENWOOD Music Editor Light (KME Light)/ KENWOOD Music Control (KMC) file

( 16)

: FILEREPEAT, REPEATOFF

Random play

Press 3 repeatedly.

• MP3/WMA/WAV/FLAC file or iPod or KME Light/ KMC file: FOLDERRANDOM, RANDOMOFF

Press and hold 3 to select “ALLRANDOM”.

Do not leave the cable inside the car when not using.

You can still play/pause, file skip, fast-forward or reverse files from the unit.

Only for MP3/WMA/WAV/FLAC files. This does not work for iPod.

For iPod: Applicable only when

[MODE OFF]

is selected.

USB / iPod

Select a file from a list

For iPod: Applicable only when selected.

( 6)

1 Press . 2 Turn the volume knob to make a selection,

then press the knob.

• MP3/WMA/WAV/FLAC file: Select the

desired folder, then a file.

• iPod or KME Light/ KMC file: Select the

desired file from the list (PLAYLISTS, ARTISTS, ALBUMS, SONGS, PODCASTS*, GENRES, COMPOSERS*).

Only for iPod.

• To return to the root folder (or first file), press number button 5 iPod.

• To return to the previous setting item or hierarchy, press

• To cancel, press and hold

If you have many files....

You can search through them quickly (on step

2 above) at a preset skip search ratio by

pressing S / T.

• See also “Set the skip search ratio.”

• Pressing and holding S / T skip songs at the maximum ratio (10 setting made.

• For USB: Only for files registered in the database created with KME Light/ KMC.

[MODE OFF]

( 8)

) regardless of the

ENGLISH |

USB / iPod

Direct Music Search (using RC-406)

Press DIRECT.

1 2 Press the number buttons to enter a file

number.

3 Press ENT IW to search for music.

• To cancel, press .

• Not available if Random Play is selected.

• Not applicable for iPod, KME Light/ KMC file.

Select a song by name

While listening to iPod...

1 Press . 2 Turn the volume knob to select a category,

then press the knob.

3 Turn the volume knob quickly to enter

character search.

4 Turn the volume knob to select the

character to be searched for.

5 Press S / T to move to the entry

position.

You can enter up to 3characters.

6 Press the volume knob to start searching. 7 Turn the volume knob to make a selection,

then press the knob.

Repeat step

selected.

• To search for a character other than A to Z and 0 to 9, enter only “

• To return to the previous hierarchy, press

• To return to the top menu, press number button 5 iPod.

• To cancel, press and hold

7 until the desired item is

”.

Set the skip search ratio

While listening to iPod or KME Light/ KMC file...

1 Press the volume knob to enter 2 Turn the volume knob to select

press the knob.

[FUNCTION]

[USB]

, then

3 Turn the volume knob to select

[SKIP SEARCH]

, then press the knob.

4 Turn the volume knob to make a selection,

then press the knob.

0.5%

(default)/ 1%/ 5%/

ratio over the total files.

10%

: Skip search

5 Press and hold to exit.

Change the USB drive

When a smartphone (Mass Storage Class) is connected to the USB input terminal, you can select its internal memory or external memory (such as an SD card) to playback the stored songs. You can also select the desired drive to playback when a multiple drives device is connected.

Press 5 iPod repeatedly to select the desired drive.

(or)

1 Press the volume knob to enter 2 Turn the volume knob to select

press the knob.

[FUNCTION]

[USB]

, then

3 Turn the volume knob to select

[MUSIC DRIVE]

, then press the knob.

4 Press the volume knob to select

[DRIVE CHANGE]

The next drive is selected automatically. Repeat steps 1 to 4 to select the following drives.

Selectable items:

[DRIVE1]

[DRIVE5]

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]. ( 4)

Start listening

Connect a portable audio player

(commercially available).

Auxiliary input jack

Portable audio

3.5mm stereo mini plug with “L” shaped connector (commercially available)

2 Press BSRC to select AUX. 3 Turn on the portable audio player and

start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select

then press the knob.

3 Turn the volume knob to select

SET]

, then press the knob.

4 Turn the volume knob to make a selection,

then press the knob.

AUX

(default)/

DVD/ PORTABLE/ GAME/ VIDEO/ TV

5 Press and hold to exit.

player

[FUNCTION] [SYSTEM]

[AUX NAME

Pandora®

Preparation:

Install the latest version of the Pandora application onto your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]. ( 4)

Start listening

Open the Pandora application on

your device.

2 Connect your device to the USB

input terminal.

USB input terminal

USB cable from the rear of the unit

The source changes to PANDORA

FRONT/ PANDORA REAR and broadcast starts.

* Do not leave the cable inside the car

when not using.

KCA-iP102 (optional accessory) or accessory cable of the iPod/iPhone

To Do this

Pause or resume playback

Thumbs up or thumbs down

Skip a track

Create a new station

Press 6 IW (or press ENT IW

on RC-406).

Press

• If thumbs down is selected, the

/ .

current track is skipped.

Press T (or press T(+) on

RC-406).

1 Press and hold the volume

knob.

2 Turn the volume knob to

select

[FROM TRACK]

ARTIST]

A new station is created based

Save a station Press and hold one of the

• To select a stored station, press

Search for a registered station

1 Press . 2 Turn the volume knob to

, then press the knob.

on the current song or artist.

number buttons (1to5) to store.

one of the number buttons (1to5).

make a selection, then press the knob (or press J / K on RC-406).

[BY DATE]:

According to the

registered date.

[A-Z]:

Alphabetical order.

3 Turn the volume knob to the

desired station, then press the knob.

[FROM

BLUETOOTH®

You can operate Bluetooth devices using this unit.

Connect the microphone

Rear panel

Microphone input jack

Adjust the microphone angle

If you turn off the unit or detach the control panel during a phone call conversation, the Bluetooth connection is disconnected. Continue the conversation using your mobile phone.

Secure using cord clamps (not supplied) if necessary.

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) – Object Push Profile (OPP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP)

Microphone (supplied)

ENGLISH |

BLUETOOTH®

Pair a Bluetooth device

When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device. Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit.

• Up to five devices can be registered (paired) in total.

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

• This unit supports Secure Simple Pairing (SSP).

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.

1 Press B SRC to turn on the unit. 2 Search and select this unit model name (KMM-X5*BT) on the

Bluetooth device.

“PAIRING”

KNOB” scrolls on the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed and “BT” will light

up when the Bluetooth connection is established.

• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.

• Pairing request (via Bluetooth) is automatically activated if an iPhone/ iPod touch is connected through the USB input terminal. (Applicable only if

[AUTO PAIRING]

Press the volume knob to pair once you have confirm the device name.

is set to

[ON]

( 13)

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device connected.

1 Press and hold .

“PLEASE PAIR YOUR PHONE” appears.

2 Search and select this unit model name (KMM-X5*BT) on the

Bluetooth device.

3 Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CNT: Hands-Free Profile (HFP) compatibility AUD CNT: Advanced Audio Distribution Profile (A2DP) compatibility PB DL: Phonebook Access profile (PBAP) compatibility

• To cancel check mode, press and hold B SRC to turn off the unit.

Bluetooth mobile phone

To Do this

Receive a call

Reject an incoming call

End a call

Press or the volume knob or one of the

number buttons (1 to 6) (or press RC-406).

• All the button illumination flash when there is an incoming call.

• When

[AUTO ANSWER]

time, the unit answers incoming call automatically.

is set to the selected

(12)

Press B SRC (or press on RC-406).

Press or B SRC (or press on RC-406).

BLUETOOTH®

To Do this

Switch between hands-free and private talk modes

Adjust the phone volume

Switch between two connected phones

Press 6IW during a call.

• Operations may vary according to the connected Bluetooth device.

Turn the volume knob during a call.

Phone volume:

• This adjustment will not affect the volume of the other sources.

[00]

[35]

(Default:

[15]

)

Press repeatedly.

• Not applicable during a call.

Improve the sound quality during a call

While talking on the phone...

1 Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to make a selection (see the following table),

then press the knob.

3 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

MIC GAIN –20

NR LEVEL –5

ECHO CANCEL 1

—+8(0):The sensitivity of the microphone increases as the

number increased.

—

–20(–10

being heard during a phone conversation.

—10(4):Adjust the echo cancellation delay time until the least echo

is being heard during a phone conversation.

):Adjust the noise reduction level until the least noise is

Text message notification

When the phone receives a text message, the unit rings and “SMS RECEIVED” appears.

• You cannot read, edit, or send a message through the unit.

• To clear the message, press any button.

Use Voice Recognition

Press and hold to activate Voice Recognition.

The connected phone (which has been paired the earliest) is

activated. However, if priority device is connected, pressing and holding

activate the priority device. (

13, DVC PRIORITY)

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Bluetooth mode operations

Press to enter Bluetooth mode.

2 Turn the volume knob to make a selection (see the following table),

then press the knob.

3 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

CALL HISTORY

Press the volume knob to select a name or a phone number.

• “I” indicates call received, “O” indicates call made, “M” indicates call missed.

• Press

DISP SCRL

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

to change the display category (NUMBER or NAME).

ENGLISH |

BLUETOOTH®

PHONE BOOK1 Turn the volume knob to select a name, then press the

NUMBER DIAL

VOICE

BATT* LOW SIGNAL* NO SIGNAL/ LOW/ MID/ MAX

knob.

Turn the volume knob to select a phone number, then

press the knob to call.

• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit when pairing. If the phone does not support PBAP, “TRANSFER PB” appears. Transfer the phonebook manually.

(13, TRANSFER PB)

• Contacts are categorized as: MO(mobile), HM(home), OF(office), OT(others), GE(general)

• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)

• If the phonebook contains many contacts,

contact by name).

Turn the volume knob to select a number (0 to 9) or

character (

Press

Repeat steps

Press the volume knob to call.

Press the number buttons (0 to 9) to enter the phone

Press to call.

Speak the name of the contact you want to call or use the voice command to control the phone functions.

Voice Recognition)

current received signal.

, #, +).

S / T

number.

(or using RC-406)

number.

MID/ FULL

to move the entry position.

and 2 until you finish entering the phone

:Shows the strength of the battery.

:Shows the strength of the

(Select a

(11, Use

SETTINGS

AUTO ANSWER

RING MODE SYSTEM:

SMS NOTIFY* ON:

* Functionality depends on the type of the phone used.

1 —30

:The unit answer incoming call automatically in the selected time.;

OFF

:Cancels.

The unit rings to notify you when a call/text message comes in.

(Default ring tone is different according to the paired device.)

•

CALL:

Selects your preferred ring tone (

•

MESSAGE:

Selects your preferred ring tone (

messages.

PHONE:

The unit uses the connected phones’ ring tone to notify you when a call/text

message comes in. (The connected phone will ring if it does not support this feature.)

The unit rings and “SMS RECEIVED” appears to notify you of an incoming text

message.;

OFF

:Cancels.

TONE 1 — 5

) for incoming calls.

TONE 1 — 5

) for incoming text

Default:

Select a contact by name

• You can search through the contacts quickly according to the first letter (A to Z), number (0 to 9), or symbol.

• The second alphabet of the contact will be searched if the first alphabet does not exist.

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[PHONE BOOK]

, then press the knob.

3 Turn the volume knob quickly to enter alphabet search mode.

The first menu (ABCDEFGHIJK) appears. To go to the other menu

(LMNOPQRSTUV or WXYZ1

), press / .

4 Turn the volume knob or press S / T to select the desired first letter, then

press the knob.

• To search with numbers, select “1”.

• To search with symbols, select “ ”.

5 Turn the volume knob to select a name, then press the knob. 6 Turn the volume knob to select a phone number, then press the knob to call.

To return to the previous hierarchy, press .

BLUETOOTH®

Store a contact in memory

You can store up to 6 contacts.

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[NUMBER DIAL]

, then press the knob.

[CALL HISTORY], [PHONE BOOK]

, or

3 Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select

step

and store a blank number.

[NUMBER DIAL]

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Delete a contact

Not applicable for mobile phone that supports PBAP.

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

press the knob.

[CALL HISTORY]

[PHONE BOOK]

, then

3 Turn the volume knob to select a contact.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold the volume knob to enter delete mode. 5 Turn the volume knob to select

press the knob.

DELETE ONE DELETE ALL

step 2 is deleted.

: Selected name or phone number in step 3 is deleted.

: All names or phone numbers from the selected menu in

6 Turn the volume knob to select

[DELETE ONE]

[YES]

[NO]

[DELETE ALL]

, then press the knob.

, then

Bluetooth mode settings

Press the volume knob to enter

1 2 Turn the volume knob to select

[FUNCTION]

[BT MODE]

, then press the knob.

3 Turn the volume knob to make a selection (see the following table),

then press the knob.

4 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

PHONE SELECT AUDIO SELECT DEVICE DELETE

DVC PRIORITY

TRANSFER PB

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

BT HF/AUDIO FRONT

INITIALIZE YES

Selects the phone or audio device to connect or disconnect.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

Selects a device to be connected as priority device. “

” appears in front of the device name set as priority.

“DL PB ” appears and transfer the phonebook of the connected

phone to this unit manually. * Selectable only when the connected phone supports OPP.

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press

S / T

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the Bluetooth device is within

range.;

OFF

:The unit automatically pair supported Bluetooth device (iPhone/iPod touch) when it is connected through USB input terminal.Depending on the iOS version of the connected iPhone/iPod touch, this function may not work. ;

OFF

:Ouputs audio from the front left and right speakers.;

ALL

:Outputs audio from all the speakers. :Initializes all the Bluetooth settings (including stored pairing,

phonebook, and etc.).;

to move the entry position.

and 2 until you finish entering the PIN code.

:Cancels.

[YES]

[NO]

, then press the knob.

ENGLISH |

+ 29 hidden pages