• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has
been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission.
• Operations are explained mainly
using buttons on the faceplate of
• [
XX
• (
XX) indicates references are
available on the stated page.
.
] indicates the selected items.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
•
Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
• For
Remote control (RC-406):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
/ : USB rating is indicated on the main unit. To view, detach the faceplate.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
( 3)
Connector (on the reverse
side of the faceplate)
2
Page 3
BASICS
Faceplate
Volume knob
(turn/press)
Detach button
Loading slot
Display window
Attach
Detach
How to reset
Remote control (RC-406)
(supplied for / / /
also be remotely controlled with an optionally
purchased remote control.
*
Not used
/ / )
/ / can
Remote sensor (Do not
expose to bright sunlight.)
Pull out the
insulation
sheet when
using for the
first time.
Your preset
adjustments will
also be erased.
ToOn the faceplateOn the remote control
Turn on the power
Adjust the volumeTurn the volume knob.Press
Select a source
Change the display
information
Press
• Press and hold to turn off the power.
Press
Press
• Press and hold to scroll the current display information.
.
repeatedly.
repeatedly.
How to replace the battery
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
or .
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Press SRC repeatedly.
( not available )
ENGLISH
3
Page 4
GETTING STARTED
1
Select the display language and cancel the
demonstration
When you turn on the power (or after you reset the unit), the display
shows:
• For
“SELLANGUAGE”
• For
“CANCEL DEMO”
1 Turn the volume knob to select [
then press the knob.
[
ENG
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME
KNOB”.
2 Press the volume knob.
[
YES
3 Press the volume knob again.
“DEMOOFF” appears.
2
Press the volume knob to enter [
1
2 Turn the volume knob to select [
3 Turn the volume knob to select [
knob.
4 Turn the volume knob to make the settings, then press the knob.
Day
5 Turn the volume knob to select [
knob.
4
/ / / :
“PRESS” “VOLUMEKNOB”
/ / / / :
“PRESS” “VOLUME KNOB” : Proceed to step 2.
ENG
] (English) or [
] is selected for the initial setup.
] is selected for the initial setup.
Set the clock
FUNCTION
].
CLOCK
], then press the knob.
CLOCK ADJUST
Hour Minute
CLOCK FORMAT
], then press the
], then press the
RUS
] (Russian),
6 Turn the volume knob to select [
12H
] or [
24H
], then press the knob.
7 Press and hold to exit.
To return to the previous setting item, press .
(Except for )
While in clock display screen...
Press and hold to enter clock adjustment mode directly.
Then, perform step
3
Set the initial settings
Press repeatedly to enter STANDBY.
1
2 Press the volume knob to enter [
For
CONTROL
4 to set the clock.
/ /
/ / :
] directly.
FUNCTION
].
/ / /
Pressing AUD enters [
AUDIO
3 Turn the volume knob to make a selection (see the following table),
then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
Default:
AUDIO CONTROL
SWITCH
PREOUT
SP SELECTOFF/ 5/4/ 6 × 9/6/ OEM
DISPLAY
EASY MENU
REAR/ SUB-W
subwoofer are connected to the line out terminals on the rear (through an
external amplifier).
4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.
(For )
ON
entering [
[
COLORSELECT
or
REAR/ SUBWOOFER: Selects whether rear speakers or a
: Selects according to the speaker size (5inches or
:Both display and button illumination change to white color when
FUNCTION
].;
OFF
:Both display and button illumination remain as
] color. ( 11)
XX
Page 5
GETTING STARTEDRADIO
TUNER SETTING
PRESET TYPE
SYSTEM
KEY BEEP
TDF ALARM
SOURCE SELECT
PANDORA SRC
BUILT-IN AUX ON
P-OFF WAIT
CD READ1
F/W UPDATE
UPDATE SYSTEM
F/W UP xx.xx
CLOCK
CLOCK DISPLAY
ENGLISH
РУССКИЙ
NORMAL
:Memorizes one station for each preset button in each band (
MIX
:Memorizes one station for each preset button, regardless of the selected band.
ON
:Activates the keypress tone.;
(For / / / / )
ON
:Activates the alarm if you forget to detach the faceplate when ACC is set to OFF.;
OFF
:Deactivates.
(For )
ON
:Enables PANDORA in source selection.;
:Enables AUX in source selection.;
(For / / / )
Applicable only when the demonstration mode is turned off.
Sets the duration when the unit will automatically turns off (while in standby mode) to save
the battery.
20M
:20 minutes;
:Automatically distinguishes between audio file disc and music CD.; 2:Forces to play as a
music CD. No sound can be heard if an audio file disc is played.
YES
:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
ON
:The clock time is shown on the display even when the unit is turned off.;
(For
Selected language is use as the display langauge for [
(folder name, file name, song title, artist name, album name) if applicable.
40M
/ / / )
:40 minutes;
OFF
:Deactivates.
OFF
60M
OFF
:Disables. ( 9)
:Disables. ( 10)
:60 minutes;
FUNCTION
OFF–––
RADIO
).;
:Cancels
OFF
:Cancels.
] menu and Tag information
Supported band:
For / / /
For / / / /
Search for a station
Press repeatedly to select TUNER.
1
2 Press repeatedly (or press /
on RC-406) to select the band.
3 Press S/T (or press S/ on RC-406)
to search for a station.
• To change the searching method for S/T: Press
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number
buttons (1to6).
• To select a stored station: Press one of the number
buttons (1to6) (or press one of the number buttons
(1to6) on RC-406).
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step
Tuning is automatically canceled.
2, Direct Access
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to make a selection (see the following
table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
LOCAL SEEK
AUTO
MEMORY
MONO SET ON
ON
:Searches only stations with good reception.;
For / / /
For / / /
•
Settings made are applicable only to the selected source/station.
Once you change the source/station, you need to make the
settings again.
YES
:Automatically starts memorizing 6 stations with good
reception.;
•
Selectable only if [
:Improves the FM reception, but the stereo effect may be lost.;
OFF
:Cancels.
:
FM stations only
/ :
NO
:Cancels.
NORMAL
AM/ SW1/ SW2 stations only
] is selected for [
OFF
:Cancels.
PRESET TYPE
]. ( 5)
NEWS SETON
REGIONAL*1ON
AF SET*
2
TI*
PTY SEARCH
CLOCK
TIME SYNC
1
*
Default:
For / / / : ON
For
2
*
Only for FM source.
• [
MONO SET
when the band is FM1/ FM2/ FM3.
• Available Program Type:
SPEECH
MUSIC: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS
The unit will search for the Program Type categorized under [
[
MUSIC
• If the volume is adjusted during reception of traffic information, alarm or news
bulletin, the adjusted volume is memorized automatically. It will be applied
the next time traffic information, alarm or news bulletin is turned on.
:The unit will temporarily switch to News Programme if available.;
: Switches to another station only in the specific region using the “AF” control.;
OFF
:Cancels.
1
ON
: Automatically searches for another station broadcasting the same program
in the same Radio Data System network with better reception when the current
reception is poor.;
ON
: Allows the unit to temporarily switch to Traffic Information if available (“TI”
lights up).;
Press the volume knob to enter PTY language selection. Turn the volume knob to
select the PTY language (
Selects the available Program Type (see below), then, press
ON
:Synchronizes the unit’s time to the Radio Data System station time.;
OFF
:Cancels.
/ / / / : OFF
]/ [
NEWS SET
: NEWS
, AFFAIRS
SCIENCE
, VARIED
TRAVEL
, LEISURE
OTHER M (music), JAZZ
] if selected.
OFF
:Cancels.
OFF
:Cancels.
ENGLISH/ FRENCH/ GERMAN
]/ [
REGIONAL
]/ [
AF SET
]/ [TI]/ [
, INFO (information), SPORT
, WEATHER
, FINANCE
, DOCUMENT
, COUNTRY
, CHILDREN
, NATION M (music), OLDIES
PTY SEARCH
, EDUCATE
, SOCIAL
), then press the knob.
, DRAMA
, RELIGION
OFF
:Cancels.
S
/T to start.
] is selectable only
, CULTURE
,
, PHONE IN
, FOLK M (music)
SPEECH
] or
,
,
6
Page 7
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and
playback starts.
M
Eject disc
USB input terminal
USB
CA-U1EX (max.: 500mA)
(optional accessory)
iPod/iPhone
KCA-iP102 / KCA-iP103 (optional
accessory)
of the iPod/iPhone
ANDROID
Micro USB 2.0 cable
(commercially available)
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
Label side
(for
/ )
1
*
or accessory cable
2
*
3
*
2
*
ToOn the faceplateOn the remote control
Playback / pausePress .
4
Reverse / Fast-forward
Select a track/file
Select a folder
6
Repeat play
*
*
Press and hold S/T.Press and hold S/.
Press S/T.Press S/
5
*
Press J/K.
Press repeatedly.
TRACK REPEAT/ REPEAT OFF
FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF
: Audio CD
Press
Press
.
/ .
: MP3/WMA/WAV file, iPod or
ANDROID
Random play
FILE REPEAT/ REPEAT OFF
6
*
Press or repeatedly.
DISC RANDOM/ RANDOM OFF
FOLDER RANDOM/ RANDOM OFF
: KME Light/ KMC file
: Audio CD
: MP3/WMA/WAV file, KME Light/ KMC
file, iPod or ANDROID
8
Press and hold
Select control modeWhile in iPod source, press repeatedly.
MODE ON
: Control from the iPod
MODE OFF
: Control from the unit
While in ANDROID source,
Select music drive
(
8, [
MUSIC DRIVE]
)
Press
The stored songs in the following start playback.
or to select
or 5 repeatedly.
9
*
( 8, [
ANDROID SETUP])
ALL RANDOM
*
.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drives device.
.
7
*
ENGLISH
7
Page 8
CD / USB / iPod / ANDROID
3
*
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is
shown. Follow the instructions to install the application. You can also install the latest version
of KENWOOD MUSIC PLAY application on your Android device before connecting. (
4
*
For ANDROID: Applicable only when [
5
*
For CD: Only for MP3/WMA files. This does not work for iPod/ ANDROID.
6
*
For iPod/ ANDROID: Applicable only when [
7
*
KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 12)
8
*
For CD: Only for MP3/WMA files.
9
*
You can still play/pause, file skip, fast-forward or reverse files from the unit.
BROWSE MODE
MODE OFF
] is selected. ( [
]/ [
BROWSE MODE
ANDROID SETUP
Select a file from a folder/list
Press .
1
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For USB (for KME Light/ KMC files):
Press S/T to search at a preset skip search ratio. (
Press and hold S/T to search at a 10
%
ratio.
• Not applicable for CD and MP3/WMA/WAV files.
For iPod:
You can search for a file according to the first character.
Turn the volume knob quickly to enter character search.Turn the volume knob to select the character.
To search for a character other than A to Z and 0to9, enter only “ * ”.
Press S/T to move to the entry position.
• You can enter up to 3characters.
Press the volume knob to start searching.
• To return to the root folder/ first file/ top menu, press 5.
• To return to the previous setting item, press
• To cancel, press and hold
• For iPod, applicable only when [
• For ANDROID, applicable only when [
(
[
ANDROID SETUP
])
.
MODE OFF
BROWSE MODE
] is selected. ( 7)
.
] is selected.
8
] is selected.
[
SKIP SEARCH
12)
Direct Music Search (using RC-406)
Press DIRECT.
1
2 Press the number buttons to enter a track/file number.
])
3 Press to search for music.
• To cancel, press or DIRECT.
• Not available if Random Play is selected.
• Not applicable for iPod, ANDROID, KME Light/ KMC file.
Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect
the iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to make a selection (see the following
])
table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
ANDROID SETUP
BROWSE MODE
HAND MODE
: Control from the unit (using KENWOOD MUSIC PLAY application).;
:Control other media player applications from the Android device
(without using KENWOOD MUSIC PLAY application). However, you can still play/pause
and file skip from the unit.
USB
MUSIC DRIVE DRIVE CHANGE
:The next drive ([
DRIVE 1
automatically and playback starts.
Repeat steps
SKIP SEARCH 0.5%/ 1%/ 5%/ 10%
1
to 3 to select the following drives.
: While listening to iPod, ANDROID or KME
Light/ KMC file, selects the skip search ratio over the total files.
] to [
DRIVE 5
Default:
]) is selected
XX
Page 9
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON
] for [
(for )
PANDORA SRC
]. ( 5)
Start listening
Open the Pandora application on your device.
1
2 Connect your device to the USB input terminal.
Create and save a new station
Press and hold the volume knob.
1
2 Turn the volume knob to select [
press the knob.
A new station is created based on the current song or artist.
FROM TRACK
] or [
FROM ARTIST
], then
3 Press and hold one of the number buttons (1to5) to store.
To select a stored station, press one of the number buttons (1to5).
USB input terminal
KCA-iP102 / KCA-iP103 (optional
1
*
The source changes to PANDORA and broadcast starts.
ToOn the faceplateOn the remote control
Playback / pause
Skip a track
Thumbs up or thumbs
3
*
down
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
If thumbs down is selected, the current track is skipped.
accessory)
the iPod/iPhone
or accessory cable of
2
*
Press
Press T.
Press / .
.Press
Press
Press
.
/ .
Search for a registered station
Press .
1
2 Turn the volume knob to make a selection, then press the knob.
[
BY DATE
[
]:According to the registered date
A-Z
]:Alphabetical order
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold .
(or using RC-406)
Press J / K to search for a station, then press .
.
Bookmark a song or artist information
Press and hold J.
1
2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK
[
THIS ARTIST
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this
unit.
]:Current song information
]:Current artist information
ENGLISH
9
Page 10
AUX
Preparation:
Select [
ON
] for [
BUILT-IN AUX
Start listening
Connect a portable audio player (commercially
1
available).
Auxiliary input jack
3.5mm stereo mini plug with “L” shaped
connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start
playback.
Set the AUX name
While listening to a portable audio player connected to
the unit...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
press the knob.
3 Turn the volume knob to select [
then press the knob.
4 Turn the volume knob to make a selection, then
press the knob.
AUX
(default)/
5 Press and hold to exit.
To return to the previous setting item, press .
]. ( 5)
Portable audio
player
FUNCTION
SYSTEM
], then
AUX NAME SET
DVD/ PORTABLE/ GAME/ VIDEO/ TV
].
],
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
For
/ /
/
3 Turn the volume knob to make a selection (see the following table), then press the
knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [
AUDIO CONTROL
2 Press J / K to make a selection, then press .
To return to the previous setting item, press
SUB-W LEVEL –15
BASS LEVEL–8
MID LEVEL–8
TRE LEVEL–8
EQ PRO
BASS ADJUST
MID ADJUST
to
+15 (0
)Adjusts the subwoofer output level.
to +8 (+6)
to +8 (+5)
to +8 (0)
BASS CTR FRQ
BASS LEVEL–8
BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00
BASS EXTENDON
MID CTR FRQ
MID LEVEL–8
MID Q FACTOR0.75/ 1.00/ 1.25
FUNCTION
].
AUDIO CONTROL
:
Pressing AUD enters [
].
Adjusts the level to memorize for each source. (Before making an adjustment,
select the source you want to adjust.)
:Selects whether to scroll the display information
FUNCTION
DISPLAY
], then press the
preset colors*2: Selects your
CUSTOM R/G/B
].
1
).
OFF
:Cancels.
].
XX
Default:
] or preset
ENGLISH
11
Page 12
MORE INFORMATION
General
•
This unit can only play the following CDs:
•
Detailed information and notes about the playable audio files are stated in an online manual
on the following web site: www.kenwood.com/cs/ce/audiofile/
Playable files
•
Playable audio file: MP3 (.mp3), WMA (.wma)
•
Playable disc media: CD-R/CD-RW/CD-ROM
•
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
•
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
Unplayable discs
•
Discs that are not round.
•
Discs with coloring on the recording surface or discs that are dirty.
•
Recordable/ReWritable discs that have not been finalized.
•
8cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•
This unit can play MP3/WMA/WAV files stored on a USB mass storage class device.
•
You cannot connect a USB device via a USB hub.
•
Connecting a cable whose total length is longer than 5m may result in abnormal playback.
•
This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About KENWOOD Music Editor Light and KENWOOD Music Control
•
This unit supports the PC application KENWOOD Music Editor Light and Android™ application
KENWOOD Music Control.
•
When you play audio files with song data added using the KENWOOD Music Editor Light or
KENWOOD Music Control, you can search for audio files by Genres, Artists, Albums, Playlists,
and Songs.
•
KENWOOD Music Editor Light and KENWOOD Music Control are available on the following
web site: www.kenwood.com/cs/ce/
About iPod/iPhone
Made for
-
iPod touch (2nd, 3rd, 4th, and 5th generation)
-
iPod classic
-
iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
-
iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
•
For the latest compatible list and software versions of iPhone/iPod, see:
www.kenwood.com/cs/ce/ipod
•
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.
About Android device
•
This unit supports Android OS 4.1 and above.
•
Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
(AOA) 2.0.
•
If the Android device supports both mass storage class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
•
For more information and the latest compatible list, see: www.kenwood.com/cs/ce/
About Pandora
•
Pandora is available only in the U.S., Australia and New Zealand.
•
Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired, or some or all of the services may
become unavailable.
•
Some functions of Pandora cannot be operated from this unit.
•
For issues using the application, please contact Pandora at pandora-support@pandora.com.
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial
telephone accessory. (
When a call comes in, “CALL” appears. (The audio system pauses.)
• To continue listening to the audio system during a call, press
“CALL” disappears and the audio system resumes.
When the call ends, “CALL” disappears. (The audio system resumes.)
16, 17
)
.
12
Page 13
TROUBLESHOOTING
SymptomRemedy
Sound cannot be heard.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
“PROTECTING SEND SERVICE”
appears.
General
•
Sound cannot be heard.
•
The unit does not turn on.
•
Information shown on the
display is incorrect.
The unit does not work at all.Reset the unit. (
•
Radio reception is poor.
•
Static noise while listening to
adio
R
the radio.
Disc cannot be ejected.
Noise is generated.Skip to another track or change the disc.
Tracks do not play back as you
intended them to play.
“READING” keeps flashing.Do not use too many hierarchical levels or folders.
Elapsed playing time is not
CD / USB / iPod
correct.
Correct characters are not
displayed (e.g. album name).
•
Adjust the volume to the optimum level.
•
Check the cords and connections.
Turn the power off, then check to be sure the terminals of
the speaker wires are insulated properly. Turn the power
on again.
Send the unit to the nearest service center.
Clean the connectors. (
•
Connect the antenna firmly.
•
Pull the antenna out all the way.
Press and hold M to forcibly eject the disc. Be careful not
to drop the disc when it is ejected. If this does not solve
the problem, reset the unit. (
Playback order is determined when files are recorded.
This is caused by how the tracks are recorded.
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
For
displayed if [
2)
3)
3)
/ / /
: Uppercase Cyrillic letters can also be
РУССКИЙ
] is selected. ( 5)
SymptomRemedy
“NA FILE”Make sure the disc contains supported audio files.
“NO DISC”Insert a playable disc into the loading slot.
“TOC ERROR”Make sure the disc is clean and inserted properly.
“PLEASE EJECT”Reset the unit. If this does not solve the problem,
“READ ERROR”Copy the files and folders onto the USB device again.
“NO DEVICE”Connect a USB device, and change the source to
CD / USB / iPod
“COPY PRO”A copy-protected file is played.
“NA DEVICE”Connect a supported USB device, and check the
“NO MUSIC”Connect a USB device that contains playable audio
“iPod ERROR”
•
Sound cannot be heard
during playback.
•
Sound output only from
the Android device.
ANDROID
(
12)
consult your nearest service center.
If this does not solve the problem, reset the USB
device or use another USB device.
USB again.
connections.
files.
•
Reconnect the iPod.
•
Reset the iPod.
•
Reconnect the Android device.
•
If in [
HAND MODE
application on the Android device and start
playback.
•
If in [
HAND MODE
player application or use another media player
application.
•
Restart the Android device.
•
If this does not solve the problem, the connected
Android device is unable to route the audio signal
to unit. (
], launch any media player
], relaunch the current media
12)
ENGLISH
13
Page 14
TROUBLESHOOTINGINSTALLATION / CONNECTION
SymptomRemedy
Cannot playback at
[
BROWSE MODE
“NO DEVICE” or “READING”
keeps flashing.
ANDROID
Playback is intermittent or
sound skips.
“ANDROID ERROR” /
“NADEVICE”
“ADDERROR” /
“SEARCHERROR”
“CHECKDEVICE”Check the Pandora application on your device.
“NOSKIPS”The skip limit has been reached.
“NOSTATIONS”No stations are found.
“STATIONLIMIT”The number of registered stations has reached its
Pandora
“CONNECT ERROR”Communication is unstable.
“RATING ERROR”Registration of thumbs up/thumbs down has failed.
“LICENSE ERROR”You try to access from a country which Pandora is not
].
•
Make sure KENWOOD MUSIC PLAY APP is installed on
the Android device. (
•
Reconnect the Android device and make the
appropriate setting in [
•
If this does not solve the problem, the connected
Android device does not support [
(
12)
•
Switch off the developer options on the Android
device.
•
Reconnect the Android device.
•
If this does not solve the problem, the connected
Android device does not support [
(
12)
Turn off the power saving mode on the Android device.
•
Reconnect the Android device.
•
Restart the Android device.
New station creation is unsuccessful.
limit. Retry after deleting unnecessary stations from
your device.
deliverable.
8)
ANDROID SETUP
]. ( 8)
BROWSE MODE
BROWSE MODE
Warning
•
The unit can only be used with a 12V DC power supply, negative ground.
•
Disconnect the battery’s negative terminal before wiring and mounting.
•
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
•
Insulate unconnected wires with vinyl tape to prevent a short circuit.
•
Be sure to ground this unit to the car’s chassis again after installation.
].
Caution
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•
Do not connect the [ wires of speakers to the car chassis or Ground wire (black), or connect
].
them in parallel.
•
Mount the unit at an angle of less than 30º.
•
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
•
Keep all cables away from heat dissipate metal parts.
•
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the [
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. (
16, 17
)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the [ terminal of the car battery.
5 Reset the unit. (
3
)
14
Page 15
INSTALLATION / CONNECTION
Installing the unit (in-dash mounting)When installing without the mounting sleeve
(for / / / /
)
1 Remove the mounting sleeve and trim plate from the
unit.
2 Align the holes in the unit (on both sides) with the
vehicle mounting bracket and secure the unit with
screws (commercially available).
The following screws are supplied for :
Round head screws (M5 × 8mm) × 4
Flat head screws (M5 × 8mm)× 4
Sems screws (M4 × 8mm)× 1
Use only the specified screws. Using wrong screws might damage the unit.
To secure the
mounting bracket
To secure the ground
wire (black)
How to remove the unit
1
Detach the faceplate.
Hook on the top side
Orientate the trim plate as
illustrated before fitting.
Part list for installation
Do the required wiring.
(
16, 17
)
Dashboard of
your car
Bend the appropriate tabs to hold the
mounting sleeve firmly in place.
2 Fit the catch pin on the extraction keys into the holes
on both sides of the
trim plate, then pull it
(A)
Faceplate
(E)
Wiring harness
(B)
Trim plate
/
/
/
(C)
Mounting sleeve
(D)
Extraction key
/
/
/
/
out.
3 Insert the extraction
keys deeply into
the slots on each
side, then follow the
arrows as shown on
the right.
ENGLISH
15
Page 16
INSTALLATION / CONNECTION
Wiring connection
(for / / / )
Front output
Rear/ subwoofer output
Rear/ subwoofer output
Antenna terminal
Connecting the ISO connectors on some VW/Audi or
Opel (Vauxhall) automobiles
You may need to modify the wiring of the supplied
wiring harness as illustrated below.
A7 (Red)
A4 (Yellow)
Ignition wire
(Red)
Battery wire
(Yellow)
Default wiring
Pin
Color and function
A4 Yellow: Battery
A5 Blue/White: Power control
A7 Red: Ignition (ACC)
A8 Black: Earth (ground) connection
B1
Purple
B2
B3
B4
B5
B6
B7
B8
]
Purple/black
Gray
]
Gray/black
]
White
White/black
]
Green
Green/black
[
[
[
[
: Rear speaker (right)
: Front speaker (right)
: Front speaker (left)
: Rear speaker (left)
16
Fuse (10A)
Yellow (Battery wire)
UnitVehicle
Red (Ignition wire)
If no connections are made, do not let the wire come out from the tab.
Brown
(Mute control wire)
To the terminal that is grounded
when the telephone rings or during
MUTE
conversation
( 12)
(To connect the Kenwood navigation
system, refer your navigation
manual.)
Red (A7)
Yellow (A4)
Blue/White
(Power control wire/
Antenna control wire)
Light blue/yellow
(Steering remote control
wire)
ANT CONT
P. CONT
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
To the power control terminal when
using the optional power amplifier
or to the antenna control terminal in
the vehicle
To the steering wheel remote control
adapter
ISO connectors
Page 17
INSTALLATION / CONNECTION
Wiring connection
(for / / / / )
Battery
Antenna terminal
To front speaker (left)
To front speaker (right)
To rear speaker (left)
To rear speaker (right)
Ignition switch
Car fuse box
Car fuse box
Front output
Rear/ subwoofer output
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Red (Ignition wire)
Yellow (Battery wire)
Black (Ground wire)
To the metallic body or chassis of the car
Rear/ subwoofer output
Fuse (10A)
If no connections are made, do not let the wire come out from the tab.
Brown
(Mute control wire)
Blue/White
(Power control wire/
Antenna control wire)
Light blue/yellow
(Steering remote control wire)
To the terminal that is grounded when the telephone
rings or during conversation
(To connect the Kenwood navigation system, refer your
navigation manual.)
To the power control terminal when using the optional
power amplifier or to the antenna control terminal in
the vehicle
To the steering wheel remote control adapter
( 12)
ENGLISH
17
Page 18
SPECIFICATIONS
/ / / :
FM Frequency Range87.5MHz — 108.0MHz (50kHz space)
Usable Sensitivity (S/N=26dB)0.71μV/75Ω
Quieting Sensitivity
(DINS/N=46dB)
Frequency Response (±3dB)30Hz — 15kHz
Signal-to-Noise Ratio (MONO)64dB
Tuner
Stereo Separation (1kHz)40dB
MW Frequency Range531kHz — 1611kHz (9kHz space)
Usable Sensitivity (S/N=20dB)28.2μV
LW Frequency Range153kHz — 279kHz (9kHz space)
Usable Sensitivity (S/N=20dB)50μV
/ / / / :
FM Frequency Range87.5 MHz — 108.0 MHz (50 kHz space)
Дата изготовления (месяц/год) находится на этикетке устройства.
/ / / :
Declaration of Conformity with regard to the EMC Directive
2004/108/EC
Declaration of Conformity with regard to the RoHS Directive
2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022,
Japan
EU Representative:
JVCKENWOOD NEDERLAND B.V.
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
The marking of products using lasers
The label is attached to the chassis/case and says that the
component uses laser beams that have been classified
as Class1. It means that the unit is utilizing laser beams
that are of a weaker class. There is no danger of hazardous
radiation outside the unit.
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik Elektrikli ve Elektronik Eşyalarin Kontrolü
Yönetmeliğe uygun olarak üretilmiştir.
Eski Elektrik ve Elektronik Ekipmanların İmha Edilmesi Hakkında Bilgi (atık yan ürün
toplama sistemlerini kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti olan çöp kutusu) ürünler ev atıkları olarak
atılamaz.
Eski elektrik ve elektronik ekipmanlar, bu ürünleri ve ürün atıklarını geri
dönüştürebilecek bir tesiste değerlendirilmelidir. Yaşadığınız bölgeye en yakın
geri dönüşüm tesisinin yerini öğrenmek için yerel makamlara müracaat edin.
Uygun geri dönüşüm ve atık imha yöntemi sağlığımız ve çevremiz üzerindeki
zararlı etkileri önlerken kaynakların korunmasına da yardımcı olacaktır.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has
been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission.
• Android is trademark of Google Inc.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.