Kenwood KDC-415UR, KDC-4651URY, KDC-4051UR, KDC-4051URY, KDC-4551UB User Manual [ru]

...

“Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect

specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and

other countries.

KDC-4051UG KDC-4051UR KDC-4051URY KDC-415UA KDC-415UR KDC-4251URY KDC-4451UQ KDC-4551UB KDC-455UW KDC-4651URY

CD-RECEIVER

INSTRUCTION MANUAL

CD-RECEIVER

BEDIENUNGSANLEITUNG

РAДИОПРИЕMНИК С KOMПAKT–ДИСKAMИ

ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ

АВТОМАГНІТОЛА

ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ

The “AAC” logo is a trademark of Dolby Laboratories.

This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment.

Изделие изготовлено в Mалайзии

CONTENTS

Safety 2 Preparation 4

How to attach/detach the faceplate How to reset your unit Initial settings before operations

Basic operations 5 Getting started 7

Canceling the display demonstration Setting the demonstration mode Adjusting the clock

Listening to the radio 8

Adjust [SETTINGS] mode settings

Listening to the other external components Listening to a disc/ USB device/ iPod 10

Start playing a disc

Functions of KDC-4651URY with remote controller

(RC-405)

Direct Music Search Connecting a USB device Connecting an iPod

KDC-4651URY only)

Selecting Repeat Play Selecting Random Play Selecting Scan Play Selecting a folder/track/file

Functions of KDC-4551UB/ KDC-455UW/

KDC-4651URY with iPod

Alphabet Search and My Playlist for iPod iPod control by Hand Mode Adjust [SETTINGS] mode settings

(KDC-4551UB/ KDC-455UW/

Function settings 13 Using the remote controller (RC-405) 15

Equipped for

KDC-4651URY

Troubleshooting 16 Installation/connection 17

Basic procedure Warning Caution Wiring connection Installing the unit Removing the unit

Specifications 21

Safety

WARNING

Stop the car before operating the unit.

Important to know...

To prevent a short circuit, never put or

leave any metallic objects (such as coins or metal tools) inside the unit.

Caution: Adjust the volume so that you

can hear sounds outside the car. Driving with the volume too high may cause an accident.

Condensation: When the car is air-

conditioned, moisture may collect on the laser lens. This may cause disc read errors. In this case, remove the disc and wait for the moisture to evaporate.

This unit can only play the CDs with:

The illustrations in this manual are

examples used to explain more clearly how the controls are used. Therefore, what appears on the illustrations may differ from what appears on the actual equipment.

A USB connection cable, CA-U1EX (optional

accessory) is required for connecting a USB device.

You can connect an Apple iPod/iPhone

with

KDC-4551UB/ KDC-455UW/ KDC-4651URY

The word “iPod” appearing in this manual

indicates the iPod or iPhone connected to this unit with a connection cable, KCA-iP101 (optional accessory).

If you experience problems during

installation, consult your Kenwood dealer.

When you purchase external components,

check with your Kenwood dealer to make sure that they work with your model and in your area.

Detailed information and notes about the

playable audio files are stated in an online manual on the following site: www.kenwood.com/cs/ce/audiofile/

Declaration of Conformity with regard to the EMC Directive 2004/108/EC

Manufacturer:

Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

EU Representative’s:

Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands

This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.

Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. Notice: The sign “Pb” below the

symbol for batteries indicates that this battery contains lead.

The marking of products using lasers

ENGLISH

The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

For Turkey

Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.

This product complies with Directive, Number 26891 regarding “REGULATION ON THE RESTRICTION OF THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT”.

Muting upon the reception of a phone call

To use this feature, connect the MUTE lead to your telephone using a commercial telephone accessory. (page 18, 19)

When a call comes in, “CALL” appears.

The audio system pauses. To continue listen to the audio system

during a call, press SRC. “CALL” disappear and the audio system resumes.

When a call ends, “CALL” disappear.

The audio system resumes.

Preparation

How to attach/detach the faceplate

Do not expose the faceplate to direct

sunlight, excessive heat, or humidity. Also avoid places with too much dust or the possibility of water splashing.

Keep the faceplate in its casing while

detached.

The faceplate is a precision piece of

equipment and can be damaged by shocks or jolts.

To prevent deterioration, do not touch the

terminals of the unit and faceplate with your fingers.

Item Selectable setting (Preset: *)

PRESET TYPE NORMAL/ NORM *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ MW/

KEY BEEP ON */ OFF: Activates/deactivates the keypress tone. RUSSIAN SET ON: Folder name, file name, song title, artist name, album name are displayed in Russian (if applicable). ;

P-OFF WAIT Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.

BUILT-IN AUX/ BUILTIN AUX

CD READ 1 *: Automatically distinguishes between audio file disc and music CD. ; 2:

SWITCH PREOUT/ SWITCH PRE

SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance. F/W UP xx.xx YES: Starts upgrading the firmware. ; NO *:

[SWITCH PREOUT/ SWITCH PRE] is selectable only with KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4551UB/ KDC-455UW/ KDC-4651URY.

LW). ; MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ MW/ LW).

OFF *: Cancels.

–––– : Cancels ; 20M *: 20 minutes ; 40M: 40 minutes ; 60M: 60 minutes ON1 *: Outputs sound of the connected external component through the car speakers when “AUX” is

selected as the source. ; ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When you turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn the volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.

sound can be heard if an audio file disc is played. REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on

the rear of the unit (through an external amplifier).

For details on how to update the firmware, see: www.kenwood.com/cs/ce/

How to reset your unit

If this unit fails to operate properly, press the reset button.

Reset button

The unit returns to factory settings when the reset button is pressed.

Initial settings before operations

Press SRC to enter [STANDBY] mode.

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [INITIAL SET], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection.

Hold to finish the procedure.

Forces to play as a music CD. No

Cancels (upgrading is not activated).

Basic operations

Display window

KDC-4551UB/ KDC-455UW/ KDC-4651URY:

KDC-4051UG/ KDC-4051UR/ KDC-4051URY/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4451UQ:

ENGLISH

Volume knob

Detaches the faceplate

The illustration and button names used for explanation in this manual are of

KDC-455UW/ KDC-4651URY

otherwise).

Refer to the table below for the difference:

KDC-4551UB/ KDC-455UW/ KDC-4651URY

iPod

3 (ALL RDM) 3

(MEMO MY LIST)

(unless mentioned

KDC-4051UG/ KDC-4051UR/ KDC-4051URY/ KDC-415UA/ KDC-415UR/ KDC-4251URY/

Loading slot

KDC-4551UB/

KDC-4451UQ

Ejects the disc

USB terminal

Auxiliary input jack

The following indicator lights up when...

ST : A stereo broadcast is received. IN : A disc is in the unit. TI : Traffic Information function is

turned on.

RDS : Radio Data System service is

available.

KDC-4551UB/ KDC-455UW/ KDC-4651URY only:

ATT

(blink)

: The sound attenuates.

(Applicable only for using the remote controller (RC-405), page 15.)

EQ : [SYSTEM Q] is set to an EQ

mode other than [NATURAL]. (page 13)

B.BOOST : [BASS BOOST] is set to [1] or

[2]. (page 13)

: In Search Mode or when a

Playlist is displayed.

KDC-4651URY

When you press or hold the following button(s)...

Button General operation

Turns on. Turns off if pressed and held.

SRC

Volume knob

(turn)

Volume knob

(press)

BAND

6 (

SCRL DISP

iPod

Selects the available sources (TUNER, USB or iPod, CD, AUX, STANDBY), if the

power is turned on.

• If the source is ready, playback also starts. “iPod” and “CD” are selectable only

when an iPod is connected or a disc is loaded.

Adjusts the volume level. Selects items.

Confirms selection. Enters [FUNCTION] settings.

Selects the FM bands (FM1/ FM2/ FM3) or MW/ LW. Selects the next folder.

) Pauses/resumes playback of a disc/ USB device/ iPod.

Searches for radio station. Selects track/file. Fast-forwards/reverses tracks if pressed and held.

Changes the display information. Scrolls the display information if pressed and held. Enters clock adjustment mode directly (page 7) if pressed and held while in

clock display screen.

KDC-4551UB/ KDC-455UW/ KDC-4651URY

Selects “iPod” source. Switches the controlling terminal (HANDS ON/ HANDS OFF) for iPod

playback if pressed and held. (page 12)

KDC-4051UG/ KDC-4051UR/ KDC-4051URY/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4451UQ

only: Selects Random Play. (page 11)

Returns to the previous item. Exit from setting mode if pressed and held.

only:

About “KENWOOD Music Editor”

This unit supports the PC application “KENWOOD Music Editor Light ver1.0” or later. When you use the audio file with database information added by the “KENWOOD Music

Editor Light ver1.0,” you can search a file by title, album or artist name using Music Search.

In the Instruction manual, the term “USB device” is used to mean the device that contains

audio files with database information added with KENWOOD Music Editor.

“KENWOOD Music Editor Light ver1.0” is available from the following web site:

www.kenwood.com/cs/ce/

For further information on “KENWOOD Music Editor Light ver1.0,” refer to the site above or

the application help.

Getting started

Canceling the display demonstration

The display demonstration is always turned on unless you cancel it.

When you turn on the power (or after you reset the unit), the display shows: [CANCEL

[VOLUME KNOB]

[YES] is selected as the initial setup.

[DEMO OFF] appears.

If no operation is done for about

15 seconds or if you turn the volume knob to select [NO] in step 2, [DEMO MODE] appears and the display demonstration starts.

Setting the demonstration mode

If [ON] is selected, display demonstration

Adjusting the clock

Clock hour flashes on the display.

DEMO] \ [PRESS] \

Press the volume knob.

Press the volume knob again to confirm.

Press the volume knob to enter [FUNCTION]. Turn the volume knob to select [DEMO MODE], then press to enter. Turn the volume knob to select [ON] or [OFF].

starts if no operation is done for about 20 seconds.

Hold to finish the procedure.

Press the volume knob to enter [FUNCTION] mode. Turn the volume knob to select [SETTINGS], then press to enter. Turn the volume knob to select [CLOCK], then press to enter. Turn the volume knob to select [CLOCK ADJUST/ CLOCK ADJ], then press to enter.

Turn the volume knob to adjust the hour, then press to enter minute adjustment.

Clock minutes flashes on the display.

Turn the volume knob to adjust the minute, then press to confirm.

Press 4

hour and minute adjustment.

Hold to finish the procedure.

¢ to move between the

Maintenance

Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or soft cloth. Failure to observe this precaution may result in damage to the monitor or unit.

Cleaning the connector: Wipe off dirt on the connector of the unit and faceplate. Use a cotton swab or cloth.

Handling discs

Do not touch the recording surface of

the disc.

Do not stick tape etc. on the disc, or use a

disc with tape stuck on it. Do not use any accessories for the disc. Clean from the center of the disc and

move outward. Clean the disc with a dry silicon or soft

cloth. Do not use any solvents. When removing discs from this unit, pull

them out horizontally. Remove the rims from the center hole

and disc edge before inserting a disc.

ENGLISH

Listening to the radio

Hold to turn on or off the Traffic Information function (not applicable if “MW/ LW” is selected).

Hold for about 2 seconds to memorize the current station or the selected Program Type. (Refer to [PTY SEARCH] on the table below to select the Program Type.)

Press briefly to recall memorized station (or Program Type after entering the PTY

search mode).

Press SRC to select “TUNER.”

Press BAND repeatedly to select a band (FM1/ FM2/ FM3/ MW/ LW).

Press 4

Adjust [SETTINGS] mode settings

While listening to the radio...

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection.

Hold to finish the procedure.

LOCAL SEEK ON: Searches only FM stations with good reception. ; OFF *: Cancels. SEEK MODE Selects the tuning mode for

AUTO MEMORY

MONO SET ON: Improves the FM reception (but the stereo effect may be lost). ; OFF *: Cancels (stereo effect resumes). PTY SEARCH Selects the available Program Type (page 9). Then, press

NEWS SET 00M – 90M: Sets the time for receiving the next news bulletin. ; OFF *: Cancels. AF SET ON *: Automatically searches for another station broadcasting the same program in the same Radio Data

¢ to search for a station.

Item Selectable setting (Preset: *)

/ ¢ buttons. AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. ; MANUAL: Manually search for a station.

YES: Automatically starts memorizing 6 stations with good reception. ; NO *: is not activated). (Selectable only if [NORMAL/ NORM] is selected for [PRESET TYPE].) (page 4)

/ ¢ to start searching. Press the volume knob to enter PTY language selection. Turn the volume knob to select the PTY language (ENGLISH */ FRENCH/ GERMAN), then press to confirm.

System network with better reception when the current reception is poor. ; OFF:

Cancels (automatic memorizing

Cancels.

Item Selectable setting (Preset: *)

RDS REGIONAL/ RDS REG

AUTO TP SEEK/ ATP SEEK

[PTY SEARCH] is selectable only when the source is “FM.” [NEWS SET/ AF SET/ RDS REGIONAL/ RDS REG/ AUTO TP SEEK/ ATP SEEK] is selectable only when the source is “FM.” If other playback source is selected, these settings are selectable under [RDS SET] item. (page 14)

Available Program Type:

SPEECH MUSIC NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M (music) ROCK M (music) EASY M (music)

LIGHT M (music) CLASSICS

RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY

OLDIES FOLK M (music) DOCUMENT

The unit will search for the Program type categorized under

[SPEECH]

The Radio Data System feature won't work where the service is not supported by any

broadcasting station.

If the volume is adjusted during reception of traffic information, the adjusted volume is

memorized automatically. It will be applied the next time Traffic Information function is turned on.

ON *: Switches to another station only in the specific region using the “AF” control. ; OFF: Cancels.

ON *: Automatically searches for a station with better reception when the traffic information‘s reception is

poor. ; OFF: Cancels.

OTHER M (music)

: White character item. ;

WEATHER FINANCE CHILDREN SOCIAL

[SPEECH]

[MUSIC]

: Black character item.

[MUSIC]

NATION M (music)

if selected.

Listening to the other external components

Preparation : Make sure [ON1] or [ON2] is selected for [BUILT-IN AUX/ BUILTIN AUX]. (page 4)

ENGLISH

Press SRC to select “AUX.”

Turn on the external component and start playing.

Turn the volume knob to adjust the volume.

Portable audio device

(optional accessory)

Auxiliary input jack

3.5 mm stereo mini plug (optional accessory)

Listening to a disc/ USB device/ iPod

Ejects the disc. (“NO DISC” appears and “IN” indicator goes off.)

Press to select track/file. Hold to fast-forwards/reverses.

USB terminal

Press to select next folder.

Start playing a disc

Press SRC to turn on the power.

Insert a disc into the loading slot.

Playback starts automatically.

Press number button 6 ( ) to resume/pause playback (if necessary).

Functions of KDC-4651URY with remote controller (RC-405)

Direct Music Search

• Not available if Random Play, Scan Play,

iPod playback is selected.

Press DIRECT to enter Direct Music Search Mode.

“– – –” appears.

Press the number buttons to enter the track number.

Press 4 / ¢ to search for the music.

To cancel the Direct Music Search Mode,

press or EXIT.

Slide open the cover.

Connecting a USB device

CA-U1EX (optional accessory)

USB device (optional accessory)

Connecting an iPod

(KDC-4551UB/ KDC-455UW/ KDC-4651URY only)

Apple iPod

(optional accessory)

KCA-iP101

(optional accessory)

The source automatically switches, and playback starts.

Selecting Repeat Play

Press number button 4 (REP) repeatedly to make a selection.

Audio CD : TRACK/ TRAC (track) REPEAT,

REPEAT OFF AAC/MP3/WMA : FILE REPEAT, FOLD (folder) REPEAT,

REPEAT OFF iPod : FILE REPEAT, REPEAT OFF

Selecting Random Play

Press number button 3 (ALL RDM) or repeatedly to make a selection.

Audio CD : DISC RANDOM, RANDOM OFF AAC/MP3/WMA/iPod : FOLDER/ FOLD (folder) RANDOM,

RANDOM OFF

Press and hold number button

3 (ALL RDM) or to select “ALL RANDOM.”

– Applicable only if “RANDOM OFF” is

selected initially.

–

KDC-4551UB/ KDC-455UW/ KDC-4651URY

Changes the iPod browsing item to “songs.”

only:

Selecting Scan Play

Press number button 2 (SCAN) repeatedly to make a selection.

Audio CD : TRACK/ TRAC (track) SCAN,

SCAN OFF

AAC/MP3/WMA : FILE SCAN, SCAN OFF

If scan play is selected, the unit starts

playing the first 10-second intro of the music in the disc/current folder.

If “SCAN OFF” is selected, the unit resumes

normal play of the current song.

Selecting a folder/track/file

Press to enter Music Search mode.

“SEARCH” appears, then the current file

name appears on the display.

Turn the volume knob to select a folder/ track/file, then press to confirm.

To return to the root folder (or first track for

audio CD), press BAND.

To return to the previous folder, press . To cancel the Music Search mode, press

and hold .

< or > on the display indicates that

preceded/next item is available.

For USB device * and iPod: To skip search,

press 4 / ¢.

* This operation is effective only for the files

registered in the database created with Kenwood Music Editor. (page 6)

KDC-4551UB/ KDC-455UW/ KDC-4651URY

return to the top menu while in the search mode of an iPod, press BAND.

Discs that cannot be used

Discs that are not round. Discs with coloring on the recording

surface or discs that are dirty.

You cannot play a Recordable/ReWritable

disc that has not been finalized. (For the finalization process refer to your disc writing software, and your disc recorder instruction manual.)

3-inch CD cannot be used. Attempt

to insert using an adapter can cause malfunction.

About USB device

This unit can play AAC/MP3/WMA files

stored on a USB mass storage class device.

Install the USB device in the place where

it will not prevent you from driving your vehicle properly.

You cannot connect a USB device via a

USB hub and Multi Card Reader.

Make sure all important data has been

backed up to avoid losing the data.

Connecting a cable whose total length is

longer than 5 m can result in abnormal playback.

only: To

ENGLISH

Functions of KDC-4551UB/ KDC-455UW/ KDC-4651URY with iPod

Alphabet Search and My Playlist for iPod

Selecting a song by alphabet

Press to enter Music Search mode.

“SEARCH” appears.

Turn the volume knob to select a

category, then press to confirm.

Press again to enter alphabet search

mode.

“SEARCH <

Turn the volume knob to select the

character to be searched for.

Press 4 / ¢ to move to the entry

position.

You can enter up to three characters.

Press the volume knob to start

searching.

To cancel the Alphabet Search mode, press

and hold .

A longer searching time is required if there

are many songs or playlists in the iPod.

To search for a character other than A to Z

and 0 to 9, enter only “ * ”.

The article (a, an, the) of songs name will

be skipped during search.

– – –

>” appears.

Registering songs in the playlist

Select and play the song you want to

Press and hold number button

5 (MEMO MY LIST) to register.

“## STORED” (registration number)

appears.

You can register up to 10 songs. “MEMORY

FULL” appears, if you try to register the

eleventh song.

If you attempt to register a song from

a different iPod, “NO INFO” followed by “MPLIST DELETE” appears. To delete the playlist, turn the volume knob to select “YES,” then press to confirm.

You can also register the song displayed in

the Music Search mode by following the same procedure.

Do not register Podcasts.

Playing a song on the playlist

Press number button 5 (MEMO MY LIST) to display the playlist.

“MY PLAYLIST” appears.

Turn the volume knob to select the song you want, then press to confirm.

Random play cannot be performed during

playback of a song in the playlist.

Deleting a song on the playlist

Press number button 5 (MEMO MY LIST) to display the playlist.

“MY PLAYLIST” appears.

Turn the volume knob to select the song you want to delete, then press and hold the volume knob.

Turn the volume knob to select “DELETE ONE” or “DELETE ALL,” then press to confirm.

Select “DELETE ALL” to delete all the songs

in the playlist.

Turn the volume knob to select “YES,” then press to confirm.

“COMPLETE” appears.

iPod control by Hand Mode

Press and hold iPod to enter iPod mode.

HANDS ON : Control iPod from the iPod. “iPod MODE”

appears on the display.

HANDS OFF: Control iPod from the unit.

Adjust [SETTINGS] mode settings

While listening to an iPod...

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See the following table for selection.

Hold to finish the procedure.

Functions of KDC-4551UB/ KDC-455UW/ KDC-4651URY with iPod

Item Selectable setting (Preset: *)

SKIP SEARCH 0.5% */ 1%/ 5%/ 10%: Sets the ratio of skip when searching for a song in Music Search mode.

(Holding

4 / ¢

MPLIST DELETE YES: Deletes the saved My Playlist. ; NO *:

About compatible iPod/iPhone

Made for – iPod touch (1st, 2nd, and 3rd generation) – iPod classic – iPod with video – iPod nano (1st, 2nd, 3rd, 4th, and 5th

generation) – iPhone 4 – iPhone 3GS – iPhone 3G – iPhone

skips songs at 10% regardless of the setting made.)

Cancels.

For the latest compatible list and software

version of iPod/iPhone, see: www.kenwood.com/cs/ce/ipod

If you start playback after connecting the

iPod, the music that has been played by the iPod is played first.

In this case, “RESUMING” is displayed

without displaying a folder name, etc. Changing the browse item will display a correct title, etc.

You cannot operate iPod if “KENWOOD” or

“✓” displayed on iPod.

Function settings

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [AUDIO CONTROL/ AUDIO CTRL] or [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection. Repeat step 3 until the desired item is selected/activated. Press to return to the previous item.

Hold to finish the procedure.

ENGLISH

[AUDIO CONTROL/ AUDIO CTRL] : While listening to any source except in STANDBY state...

Item Selectable setting (Preset: *)

SUB-W LEVEL

BASS BOOST

SYSTEM Q

BASS ADJUST BASS CTR FRQ/ BASS C FRQ: 60/ 80/ 100 */ 200:

–15 — +15 (Preset: 0): Adjusts the subwoofer output level. B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to

the music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)

Selects the center frequency.

BASS LEVEL: –8 — +8 (Preset: 0): Adjusts the level. BASS Q FACTOR/ BASS Q FCTR: 1.00 */ 1.25/ 1.50/ 2.00: BASS EXTEND: ON: Turns on the extended bass. ; OFF *:

Adjusts the Q factor.

Cancels.

Continued...

Item Selectable setting (Preset: *)

MID ADJUST MIC CTR FRQ/ MID C FRQ: 0.5K/ 1.0K */ 1.5K/ 2.5K:

MID LEVEL: –8 — +8 (Preset: 0): Adjusts the level. MID Q FACTOR/ MID Q FCTR: 0.75/ 1.00 */ 1.25:

TRE ADJUST TRE CTR FRQ/ TRE C FRQ: 10.0K/ 12.5K */ 15.0K/ 17.5K:

TRE LEVEL: –8 — +8 (Preset: 0): Adjusts the level.

BALANCE L15 — R15 (Preset: 0): Adjusts the left and right speaker output balance. FADER R15 — F15 (Preset: 0): Adjusts the rear and front speaker output balance. SUBWOOFER SET/ SUB-W SET ON *: Turns on the subwoofer output. ; OFF: DETAILED SET/ DETAIL SET

LPF SUBWOOFER/ LPF SUB-W:

SUB-W PHASE: REVERSE/ REV

SUPREME SET: ON *: Creates realistic sound by interpolating the high-frequency components that are lost in

VOLUME OFFSET/ VOL OFFSET: (Preset: 0)

Select a source before making a source tone memory adjustment, [BASS ADJUST/ MID ADJUST/ TRE ADJUST]. KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4551UB/ KDC-455UW/ KDC-4651URY

only:

[SUB-W LEVEL/ SUBWOOFER SET/ SUB-W SET/ LPF SUBWOOFER/ LPF SUB-W/ SUB-W PHASE] is selectable only if

[SWITCH PREOUT/ SWITCH PRE] is set to [SUB-W]. (page 4)

[SUB-W LEVEL/ LPF SUBWOOFER/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUBWOOFER SET/ SUB-W SET] is

set to [ON].

[SETTINGS]

Item Selectable setting (Preset: *)

AUX NAME SET/ AUX NAME

CLOCK CLOCK ADJUST/ CLOCK ADJ: (For details, see page 7.)

DISPLAY DIMMER SET: ON: Dims the display illumination. ; OFF *: Cancels.

RDS SET NEWS SET/ AF SET/ RDS REGIONAL/ RDS REG/ AUTO TP SEEK/ ATP SEEK: Selectable only if any source

AUX */ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component.

(Selectable only if “AUX” is selected as the source.)

TIME SYNC: ON *: Synchronizes the Radio Data System station time data and the unit’s clock. ;

TEXT SCROLL: AUTO/ ONCE: Selects to scroll the display information automatically, or scroll only once. ;

other than tuner source is selected. (For details, see page 8, 9.)

THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies higher than 85 Hz/ 120 Hz/ 160 Hz are cut off.

(180°)/ NORMAL/ NORM (0°) *: Selects the phase angle of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [LPF SUBWOOFER/ LPF SUB-W].)

AAC/ MP3/ WMA audio compression. ; OFF: Cancels. (Selectable only when playback an AAC/ MP3/ WMA disc or a USB device, except iPod.)

–8 — +8 (for AUX) ; –8 — 0 (for other sources) each source. The volume level will automatically increase or decrease when you change the source. (Before making an adjustment, select the source you want to adjust.)

OFF: Cancels.

OFF *: Cancels.

Selects the center frequency.

Adjusts the Q factor.

Selects the center frequency.

Cancels.

Presets the volume adjustment level of

Using the remote controller (RC-405)

Equipped for KDC-4651URY

Remote sensor

Do not expose to bright sunlight.

Preparation:

When you use the remote controller for the first time, pull out the insulation sheet.

Insulation sheet

ENGLISH

If the effectiveness of the remote controller decreases, replace the battery.

Caution:

Do not set the remote control in hot places

such as on the dashboard.

Lithium battery.

Danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

The battery pack or batteries shall not be

exposed to excessive heat such sunshine, fire or the like.

Keep battery out of reach of children and in

original package until ready to use. Dispose of used batteries promptly. If swallowed contact physician immediately.

Basic operations: SRC : Selects the available sources. VOL : Adjusts the volume level.

5 / ∞ : Selects folders/files (in Music

Search mode).

ENT : Pauses/resumes playback. Confirms selection (in Music

Search mode).

*AM– / #FM+ : Selects bands. Selects folders. 4 / ¢ (+) : Searches for radio station. Selects track/file.

1 – 6 : Selects preset station. AUD : Enters [AUDIO CONTROL]

settings directly.

ATT : Attenuates the sound. (To return

to the previous level, press the button again.)

: Returns to the previous item (in

Music Search mode).

EXIT : Exit from setting mode.

Troubleshooting

Symptom Remedy/Cause

Sound cannot be heard. Adjust the volume to the optimum level. / Check the cords and connections. “PROTECT” appears and no operations can be done.

The unit does not work at all. Reset the unit.

[P-OFF WAIT]

Radio reception is poor. / Static noise while listening to the radio. “IN” flashes. The CD player is not operating properly. Reinsert the disc properly. If the condition

CD-R/CD-RW cannot be played back and tracks cannot be skipped. Disc sound is sometimes interrupted. Stop playback while driving on rough roads. / Change the disc. / Check the cords

“NA FILE” appears. The unit is playing an unsupported audio file. “NO DISC” appears. Insert a playable disc into the loading slot. “TOC ERROR” appears. The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try

“ERROR 99” appears. The unit is malfunctioning for some reason. Press the reset button on the unit. If

“COPY PRO” appears. A copy-protected file is played. “READ ERROR” appears. Copy the files and folders for the USB device again. If the error message is still

“NO DEVICE” appears. No USB device is connected. Connect an USB device, and change the source to

“NO MUSIC” appears. The connected USB device contains no playable audio file. “NA DEVICE” appears. Connect a supported USB device, and check the connections. “USB ERROR” appears. Remove the USB device, turn the unit off, then turn it on again. If the unit still

“iPod ERROR” appears. Reconnect the iPod. / Confirm that the software for the iPod is the latest version. Noise is generated. Skip to another track or change the disc. Tracks cannot play back as you have intended them to play. “READING” keeps flashing. Longer readout time is required. Do not use too many hierarchies and folders. Elapsed playing time is not correct. This is caused by how the tracks are recorded. The number of songs contained in “SONGS” category of this unit is different from that contained in “SONGS” category of iPod. Correct characters are not displayed (e.g. album name).

does not work. Turn off the demonstration mode. (page 7)

Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest service center.

Connect the antenna firmly. / Pull the antenna out all the way.

did not improve, turn off the unit and consult your nearest service center. Insert a finalized CD-R/CD-RW (finalize with the component which you used for recording).

and connections.

another disc instead.

the “ERROR 99” code does not disappear, consult your nearest service center.

displayed, initialize the USB device or use other USB devices.

USB again.

showing the same display, try to connect another USB device.

Playback order is determined when files are recorded.

Podcast files are not counted in this unit as this unit does not support the playback of podcast files.

This unit can only display letters (upper case), numbers, and a limited number of symbols. Cyrillic alphabets (upper case) can also be displayed if [RUSSIAN SET] is set to [ON]. (page 4)

Installation/connection

Part list:

A Faceplate.............................................................. (×1)

B Escutcheon ......................................................... (×1)

C Mounting sleeve ............................................. (×1)

D Casing for faceplate ...................................... (×1)

E Wiring harness .................................................. (×1)

F Removal tool .................................................... (×2)

Basic procedure

Remove the key from the ignition switch, then disconnect the · terminal of the car battery.

Make proper input and output wire connections. \ “Wiring connection” (page 18, 19)

Install the unit to your car. \ “Installing the unit” (page 20)

Reconnect the · terminal of the car battery.

Reset the unit. (page 4)

Warning

The unit can only be installed in a car with

a 12 V DC power supply, negative ground.

If you connect the ignition wire (red) and

the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

Disconnect the battery's negative terminal

and make all electrical connections before installing the unit.

Insulate unconnected wires with vinyl tape

or other similar material. If no connections are made, do not let the wire come out from the tab to prevent short circuit.

Be sure to ground this unit to the car's

chassis again after installation.

Caution

If your car's ignition does not have an ACC

position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

Do not use your own screws. Use only the

screws provided.

Install this unit in the console of your

vehicle. Make sure the faceplate will not hit the lid of the console (if any) when closing and opening.

After the unit is installed, check whether

the brake lamps, blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle

is 30° or less.

If the fuse blows, first make sure the wires

are not touching to cause a short circuit, then replace the old fuse with one that has the same rating.

Connect the speaker wires correctly to the

terminals to which they correspond. The unit may be damaged or fail to work if you share the · wires or ground them to any metal part in the car.

When only two speakers are being

connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear).

Do not touch the metal part of this unit

during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.

Mounting and wiring this product requires

skills and experience. For safety's sake, leave this work to professionals.

If you experience problems during

installation, consult your Kenwood dealer.

ENGLISH

Wiring connection

For KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4551UB/ KDC-455UW/ KDC-4651URY

KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4551UB/ KDC-455UW

Rear/subwoofer output terminals

Antenna terminal (JASO)

KDC-4251URY/ KDC-4651URY

Front output terminals

Rear/subwoofer output terminals

Fuse (10 A)

Light blue/yellow (Steering remote control wire)

Blue/White (Power control/motor antenna control wire)

Brown (Mute control wire)

Yellow (Battery wire)

Red (Ignition wire)

Red (A7)

Yellow (A4)

Yellow

Blue/White

Red

Black

ISO connectors

Color and function

Battery Power control Ignition (ACC) Earth (ground) connection

KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4551UB/ KDC-455UW/ KDC-4651URY:

steering wheel remote control adapter (optional accessory)

To the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle.

To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.)

Connecting the ISO connectors on some VW/Audi or Opel (Vauxhall) automobiles

You may need to modify the wiring of the supplied wiring harness as illustrated below.

Ignition wire

(Red)

Unit

Battery wire

(Yellow)

Default wiring

B1 / B2

Purple Gray ª / Gray/black ·

B3 / B4

White ª / White/black ·

B5 / B6

Green ª / Green/black ·

B7 / B8

/ Purple/black ·

Color and function

To the

A7 (Red)

A4 (Yellow)

Rear speaker (right) Front speaker (right) Front speaker (left) Rear speaker (left)

Vehicle

For KDC-4051URY/ KDC-4451UQ

White (+) / White/black (–) : To front speaker (left)

Gray (+) / Gray/black (–) : To front speaker (right)

Green (+) / Green/black (–) : To rear speaker (left)

Purple (+) / Purple/black (–) : To rear speaker (right)

Blue (Motor antenna control wire)

Blue/White (Power control wire)

Brown (Mute control wire)

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire)

Antenna terminal (JASO)

To the antenna control terminal in the vehicle.

To the power control terminal when using the optional power amplifier.

To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.)

Car fuse box

To the metallic body or chassis of the car

Fuse (10 A)

Ignition key switch

Car fuse box

Battery

ENGLISH

Installing the unit

Before attaching, make sure the direction of the escutcheon is correct. (Wider hooks on the top side.)

Removing the unit

Detach the faceplate.

Engage the catch pin on the removal tools into the holes on both sides of the escutcheon, then pull it out.

Insert the removal tools deeply into the slots on each side, then follow the arrows instructions as shown on the right.

Connect the wiring harness to the unit. Other wiring connection has been completed earlier. (page 18, 19)

Dashboard of your car

Bend the appropriate tabs to hold the mounting sleeve firmly in place.

About Audio file

Playable Audio file: AAC-LC (.m4a), MP3 (.mp3), WMA (.wma) Playable disc media: CD-R/RW/ROM Playable disc file format: ISO 9660 Level 1/2, Joliet, Romeo, Long file name.

Playable USB device file system: FAT16, FAT32 Although the audio files are complied with the standards listed above, the play maybe impossible depending on the types or conditions of media or device.

Specifications

FM tuner section

Frequency range:

FM1/ FM2/ FM3 (50 kHz space):

87.5 MHz — 108.0 MHz

For KDC-4451UQ

FM1/ FM2 (50 kHz space):

87.5 MHz — 108.0 MHz

FM3 (30 kHz space):

65.00 MHz — 74.00 MHz

Usable sensitivity (S/N= 26 dB): Quieting sensitivity (DIN S/N = 46 dB): Frequency response (±3 dB): Signal-to-Noise ratio (MONO): Stereo separation (1 kHz):

1.0 μV/75 Ω

30 Hz — 15 kHz

63 dB

40 dB

MW tuner section

Frequency range (9 kHz space):

531 kHz — 1 611 kHz

Usable sensitivity (S/N= 20 dB):

36 μV

LW tuner section

Frequency range: Usable sensitivity (S/N = 20 dB):

153 kHz — 279 kHz

57 μV

CD player section

Laser diode: Digital filter (D/A): D/A converter: Spindle speed: Wow & Flutter: Frequency response (±1 dB): Total harmonic distortion (1 kHz): Signal-to-Noise ratio (1 kHz): Dynamic range: AAC decode: MP3 decode:

WMA decode:

GaAIAs

8 Times Over Sampling 24 Bit 500 rpm — 200 rpm (CLV)

Below Measurable Limit

20 Hz — 20 kHz

0.01 %

105 dB

90 dB

AAC-LC “.m4a” files

Compliant with MPEG-1/2 Audio

Layer-3

Compliant with Windows

Media Audio

2.5 μV/75 Ω

USB interface

USB standard: Maximum supply current: File system:

AAC decode:

MP3 decode:

Layer-3

WMA decode:

Media Audio

USB1.1/ 2.0 (Full speed)

500 mA

FAT16/ 32

AAC-LC “.m4a” files

Compliant with MPEG-1/2 Audio

Compliant with Windows

Audio section

Maximum output power: Output power (DIN 45324, +B = 14.4 V): Speaker impedance: Tone action: Bass:

For KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4551UB/

KDC-455UW/ KDC-4651URY Preout level / load (CD): Preout impedance:

50 W × 4

4 Ω — 8 Ω

100 Hz ±8 dB

Middle:

1 kHz ±8 dB

Treble:

10 kHz ±8 dB

≤ 600 Ω

30 W × 4

2 000 mV/10 kΩ

Auxiliary input section

Frequency response (±3 dB): Input maximum voltage: Input impedance:

20 Hz — 20 kHz

1 200 mV

10 kΩ

General

Operating voltage (11 V — 16 V allowable): Maximum current consumption: Installation size (W × H × D):

182 mm × 53 mm × 158 mm

Weight:

1.3 kg

Subject to change without notice.

10 A

ENGLISH

14.4 V

INHALT

Sicherheit 2 Vorbereitung 4

Anbringen/Abnehmen der Frontblende Wissenswertes über die Rückstellung Ihres

Gerätes

Werkseitige Einstellungen vor dem Betrieb

Grundbedienung 5 Erste Schritte 7

Abbrechen der Display-Demonstrationen Einstellen des Demonstrationsmodus Uhr einstellen

Rundfunkempfang 8

Anpassen der Einstellungen im [SETTINGS]-

Modus

Hören von den anderen externen Komponenten 9

Hören von Disc/ USB-Gerät/ iPod 10

Starten des Abspielens einer Disc

Funktionen des KDC-4651URY mit Fernbedienung

(RC-405)

Direkte Musiksuche Anschließen eines USB-Geräts Anschließen eines iPod

KDC-455UW/ KDC-4651URY)

Auswählen der Wiederholwiedergabe Auswählen der Zufallswiedergabe Auswählen von Anspielen Auswählen eines Ordners/Tracks/Datei

Funktionen des KDC-4551UB/ KDC-455UW/

KDC-4651URY mit iPod

Alphabetsuche und My Playlist für iPod iPod-Steuerung im manuellen Modus Anpassen der Einstellungen im

[SETTINGS]-Modus

Funktionseinstellungen 13 Verwendung der Fernbedienung

(RC-405) 15

Ausgerüstet für

Störungssuche 16 Einbau/Anschluss 17

Grundlegendes Verfahren Warnung Vorsicht Verdrahtungsanschluss Einbau der Einheit Ausbau des Geräts

Technische Daten 21

(Nur KDC-4551UB/

KDC-4651URY

Sicherheit

WARNUNG

Halten Sie das Fahrzeug vor der Bedienung des

Geräts an.

Wichtige Hinweise...

Stellen Sie sicher, dass keine

Metallgegenstände (Münzen, Nadeln, Werkzeuge usw.) ins Innere des Geräts gelangen und Kurzschlüsse verursachen.

Vorsicht: Stellen Sie die Lautstärke so ein, dass

Sie immer noch Geräusche von außerhalb des Fahrzeugs hören können. Fahren mit zu hoher Lautstärke kann Unfälle verursachen.

Kondensation: Wenn das Fahrzeug eine

Klimaanlage hat, kann sich Beschlag auf der Laserlinse bilden. Dadurch können DiscLesefehler verursacht werden. Nehmen Sie in diesem Fall die CD aus dem Gerät und warten Sie eine Zeit lang, bis die Kondensation getrocknet ist.

Dieses Gerät kann nur CDs mit der

folgenden Kennung wiedergeben:

Die in dieser Bedienungsanleitung

dargestellten Abbildungen dienen der Veranschaulichung der Bedienung Ihres Geräts. Daher können die Abbildungen von der tatsächlichen Anzeige am Gerät abweichen.

Ein USB-Verbindungskabel CA-U1EX

(optionales Zubehör) ist zum Anschließen eines USB-Geräts erforderlich.

Sie können einen Apple iPod/iPhone mit

KDC-4551UB/ KDC-455UW/ KDC-4651URY anschließen.

Die in diesem Handbuch verwendete

Bezeichnung “iPod” weist auf den über das iPod-Anschlusskabel, KCA-iP101 angeschlossenen iPod oder das iPhone hin (optionales Zubehör).

Sollten Sie Probleme bei der Installation des

Geräts haben, lassen Sie sich bitte von Ihrem Kenwood-Fachhändler beraten.

Lassen Sie sich beim Kauf von externer

Komponenten von Ihrem Kenwood-Händler beraten um sicherzustellen, dass das Zubehör von Ihrem Modell und in Ihrem Bereich unterstützt wird.

Detailinformationen und Hinweise über

abspielbare Audiodateien werden im Online-Handbuch auf der folgenden Website gegeben: www.kenwood.com/cs/ce/audiofile/

Konformitätserklärung in Bezug auf die EMC-Vorschrift 2004/108/EC

Hersteller:

Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

EU-Vertreter:

Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, Niederlande

Dieses Produkt wird weder vom Hersteller eines Fahrzeugs während der Produktion noch von einem professionellen Importeur eines Fahrzeugs in einen EU-Mitgliedsstaat eingebaut.

Entsorgung von gebrauchten elektrischen und elektronischen Geräten und Batterien (anzuwenden in den Ländern der Europäischen Union und anderen europäischen Ländern mit einem separaten Sammelsystem für solche Geräte)

Das Symbol (durchgestrichene Mülltonne) auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall behandelt werden darf, sondern an einer Annahmestelle für das Recycling von elektrischen und elektronischen Geräten und batterien abgegeben werden muss. Durch Ihren Beitrag zur korrekten Entsorgung dieses Produktes schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Unsachgemässe oder falsche Entsorgung gefährden Umwelt und Gesundheit. Weitere Informationen über das Recycling dieses Produktes erhalten Sie von Ihrer Gemeinde oder den kommunalen Entsorgungsbetrieben. Achtung: Das Zeichen “Pb”

unter dem Symbol fur Batterien zeigt an, dass diese Batterie Blei enthalt.

Kennzeichnung von Geräten mit LaserAbtastern

Das Etikett ist am Chassis/Gehäuse angebracht und besagt, dass sich die Komponente Laserstrahlen bedient, die als Laserstrahlen der Klasse 1 klassifiziert wurden. Dies weist darauf hin, dass sich das Gerät Laserstrahlen bedient, die einer schwächeren Klasse angehören. Das bedeutet, dass durch den sehr schwachen Laserstrahl keine Gefahr durch gefährliche Strahlungen außerhalb des Geräts besteht.

Stummschaltung beim Empfang eines Telefonanrufs

Zur Verwendung dieses Merkmals schließen Sie die MUTE-Leitung an Ihr Telefon mit einem im Handel erhältlichen Telefonzubehör an. (Seite 18, 19)

Wenn ein Anruf ankommt, wird “CALL” angezeigt.

Die Audiowiedergabe wird

unterbrochen.

Um die Audioanlage auch während eines

Anrufs zu höhren, drücken Sie SRC. “CALL” verschwindet und die Wiedergabe vom Audiosystem wird fortgesetzt.

Wenn ein Anruf beendet wird,

verschwindet “CALL”.

Die Audiowiedergabe wird fortgesetzt.

DEUTSCH

Vorbereitung

Anbringen/Abnehmen der Frontblende

Setzen Sie die Frontblende nicht direktem

Sonnenlicht, extremer Wärme oder Luftfeuchtigkeit aus. Schützen Sie beides darüber hinaus vor Staub und Spritzwasser.

Bewahren Sie die Frontblende in ihrem Etui

auf, wenn sie abgenommen wurde.

Bei der Frontblende handelt es sich

um ein Präzisionsbauteil, das durch Erschütterungen oder Stöße beschädigt werden kann.

Um Beschädigungen zu vermeiden,

berühren Sie die Anschlüsse des Geräts nicht mit den Fingern.

Gegenstand Wählbare Einstellung (Preset: *)

PRESET TYPE NORMAL/ NORM *: Speichert einen Sender für jede Sendespeichertaste in jedem Frequenzband (FM1/

KEY BEEP ON */ OFF: Aktiviert/deaktiviert den Tastendruck-Signalton. RUSSIAN SET ON: Ordnername, Dateiname, Songtitel, Interpretenname, Albumname werden auf russisch angezeigt (wo

P-OFF WAIT Stellt die Zeitdauer ein, bis das Gerät automatisch ausschaltet (im Standby-Modus), um Batteriestrom zu

BUILT-IN AUX/ BUILTIN AUX

CD READ 1 *: Hiermit wird automatisch zwischen Discs mit Audiodateien und Musik-CDs unterschieden. ; 2:

SWITCH PREOUT/ SWITCH PRE

SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Wählt die Lautsprechergröße für optimale Leistung. F/W UP xx.xx YES: Startet die Aktualisierung der Firmware. ; NO *:

[SWITCH PREOUT/ SWITCH PRE] ist nur mit KDC-4051UG/ KDC-4051UR/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4551UB/ KDC-455UW/ KDC-4651URY wählbar.

FM2/ FM3/ MW/ LW). ; MIX: Speichert einen Sender für jede Sendespeichertaste ungeachtet des Frequenzbands (FM1/ FM2/ FM3/ MW/ LW).

zutreffend). ; OFF *: Hebt auf.

sparen.

–––– : Hebt auf ; 20M *: 20 Minutes ; 40M: 40 Minutes ; 60M: 60 Minutes ON1 *: Gibt Ton von der angeschlossenen externen Komponente über die Autolautsprecher aus, wenn

“AUX” als Quelle gewählt ist. ; ON2: Gibt Ton von der angeschlossenen externen Komponente aus, wenn “AUX” als Quelle gewählt ist. Beim Einschalten wird der Ton gedämpft (um Rauschen zu vermeiden, wenn keine externe Komponente angeschlossen ist). Drehen Sie den Lautstärke-Regler im Uhrzeigersinn, um auf den vorherigen Lautstärkepegel zurückzustellen. ; OFF: Deaktivieren Sie “AUX” in der Quellenwahl.

wird die Wiedergabe zwangsweise als Musik-CD durchgeführt. Es kommt kein Ton, wenn eine Disc mit Audiodateien abgespielt wird.

REAR */ SUB-W: Wählt, ob hintere Lautsprecher oder ein Subwoofer an die Line-Out-Buchsen an der Rückseite des Geräts angeschlossen sind (über einen externen Verstärker).

Einzelheiten darüber, wie Sie die Firmware aktualisieren können, siehe: www.kenwood.com/cs/ce/

Wissenswertes über die

Rückstellung Ihres Gerätes

Sollte das Gerät nicht richtig funktionieren,

drücken Sie die Rückstelltaste.

Die Rückstelltaste

Rückstelltaste

löscht alle individuellen Eingaben und stellt das Gerät auf die werkseitige Grundeinstellung zurück.

Werkseitige Einstellungen vor dem

Betrieb

Drücken Sie SRC, um auf [STANDBY]Modus zu schalten.

Drücken Sie den Lautstärke-Regler, um auf den [FUNCTION]-Modus zu schalten.

Drehen Sie den Lautstärkeregler zum Wählen von [INITIAL SET], und drücken Sie dann zum Eingeben.

Drehen Sie den Lautstärke-Regler, um eine Auswahl vorzunehmen, und drücken Sie dann zum Bestätigen.

Siehe Tabelle unten zur Auswahl.

Halten Sie gedrückt, um den Vorgang fertigzustellen.

Bricht ab (Aktualisierung wird nicht ausgeführt).

Hiermit

Grundbedienung

Displayfenster

KDC-4551UB/ KDC-455UW/ KDC-4651URY:

KDC-4051UG/ KDC-4051UR/ KDC-4051URY/ KDC-415UA/ KDC-415UR/ KDC-4251URY/ KDC-4451UQ:

Lautstärke-Regler

Frontblende abnehmen

Die Abbildungen und Tastenbezeichnungen für die Erklärungen in diesem Handbuch

beziehen sich auf

KDC-4651URY

Die Tabelle unten nennt die Unterschiede.

KDC-4551UB/ KDC-455UW/

KDC-4651URY

iPod

3 (ALL RDM) 3

(MEMO MY LIST)

KDC-4551UB/ KDC-455UW/

(wenn nicht anders angegeben).

KDC-4051UG/ KDC-4051UR/ KDC-4051URY/ KDC-415UA/ KDC-415UR/ KDC-4251URY/

Ladeschlitz

KDC-4451UQ

Disc auswerfen

USB-Anschluss

Auxiliary-Eingabebuchse

Die folgende Anzeige leuchtet auf, wenn...

ST : Eine Stereosendung empfangen

IN : Sich eine Disc im Gerät befindet. TI : Die Verkehrsfunk-Funktion

RDS : Ein Radio Data System-Service

Nur KDC-4551UB/ KDC-455UW/ KDC-4651URY

ATT

EQ : [SYSTEM Q] ist auf einen

B.BOOST : [BASS BOOST] ist auf [1] oder

: Im Suchmodus oder wenn eine

wird.

eingeschaltet ist.

verfügbar ist.

(Blinken)

: Der Ton wird gedämpft. (Gilt nur

für

KDC-4651URY

der Fernbedienung (RC-405), Seite 15.)

anderen EQ-Modus als

[NATURAL] gestellt. (Seite 13)

[2] gestellt. (Seite 13)

Wiedergabeliste angezeigt wird.

mit Verwendung

DEUTSCH

+ 56 hidden pages