How it Works
Kenwood
Loading...
KAF-3010-R
Service manual
17 pgs2.59 Mb0
Service Manual
17 pgs2.6 Mb0
User Manual
16 pgs499.72 Kb0
Table of contents
Loading...

Kenwood KAF-3010R, KAF-1010 User Manual

Download
STEREO INTEGRATED AMPLIFIER
KAF-3010R KAF-1010
INSTRUCTION MANUAL
KENWOOD CORPORA TION
B60-3742-08 00 KO (T, M) 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3
OC

Before applying power

Units are designed for operation as follows.
Europe and U.K. .....................................................................AC 230 V only
*Other countries............................. AC 110-120 /220-240 V switchable
Caution : Read this page carefully to ensure safe operation.
KAF-3010R/1010 (En)
For the United Kingdom
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code.
Blue : Neutral Brown: Live
Do not connect those leads to the earth terminal of a
three-pin plug.
*For other countries
AC voltage selection
This unit operates on 110-120 or 220-240 volts AC . The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.
AC voltage selector switch
—
AC 110 120V
Note:
Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.
AC 220
240V
—
Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Special features

SOURCE DIRECT
KAF-3010R/1010 (En)
Lets you enjoy high quality sound from the music source selected by the INPUT SELECTOR.

Contents

Before applying power
Special features System connection
Controls and indicators
Operation of remote control unit Playing music
Sound adjustment functions
Recording
In case of difficulty
Specifications
Caution : Read the pages marked carefully to ensure safe operation.
..................................................................................................................................................
Before applying power.................................................................................................................... 2
Safety precautions .......................................................................................................................... 2
..................................................................................................................................................
..................................................................................................................................................
The system control connections .......................................................................................................... 5
Connection of speakers ........................................................................................................................ 6
..................................................................................................................................................
Main unit ................................................................................................................................................ 7
Remote control unit ............................................................................................................................... 8
..................................................................................................................................................
................................................................................................................................................
Normal Playback .................................................................................................................................. 10
................................................................................................................................................
To mute sound temporarily ................................................................................................................ 11
Adjusting the left/right sound balance ............................................................................................... 11
Adjusting the tone ............................................................................................................................... 11
Emphasizing deep bass (LOUDNESS)............................................................................................... 11
To listen through headphones ............................................................................................................ 12
Listening to high quality sound from a music source (SOURCE DIRECT).................................... 12
................................................................................................................................................
To record a music source ................................................................................................................... 13
................................................................................................................................................
................................................................................................................................................
10
11
13
14 15
2
3 4
7
9

Accessories

Remote control unit (1)
(KAF-3010R only)
Batteries (R6/SUM-3) (2)
(KAF-3010R only)
AC plug adaptor (1)
Use to adapt the plug on the power cord to the shape of the wall outlet. (Accessory only for regions where use is necessary.)

System connection

KAF-3010R/1010 (En)
Make connections as shown below. When connecting the related system components, refer also
to the instruction manuals of the related components. Do not plug in the power lead until all connections are completed.
Malfunction of microcomputer
If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of diffi­culty”.
SYSTEM CONTROL selector
switch and terminals (KAF-3010R only)
SYSTEM CONTROL
ƒ
SIGNAL GND
PHONO CD TUNER TAPE
L
R
SL 16 XS-8
REC PLAY REC PLAY
MD
$
SPEAKERS
i
A or B : 4–16Ω, A and B : 8–16Ω
L R
+––+
L R
j
* Caution (for U.K.)
A
B
When using the AC outlets equipped with unit, be sure to consult your dealer for the corresponding plug.
AC outlets (KAF-3010R only)
Shape of AC outlets
* U.K.
Other countries
To wall AC outlet
AC voltage selector switch (only some areas)
UNSWITCHED
100W MAX.
AC OUTLETS
SWITCHED TOTAL
200W MAX.
AC 110 120V
—
—
AC 220
240V
Audio cords
CD player
PLAY OUT
REC IN
Tuner
PLAY OUT
REC IN
Tape deck
MD recorder
System control cord
System control cord
System control cord
Turntable
Caution regarding placement
To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projec­tions) equal to, or greater than, shown below.
Left and right panels: 10 cm, Rear panel: 10 cm, Top panel: 50 cm
About the AC outlet for other components (KAF-3010R only)
SWITCHED outlet (maximum capacity 200 W) You can connect a power cord from a cassette deck, record player, or CD player (etc.). If you leave the POWER switch of that component in the ON position, it will turn ON/OFF together with the REMOTE POWER key on this unit, for your convenience. Do not connect a component that consume more than 200 W total.
KAF-3010R/1010 (En)
The system control connections
(only for KAF-3010R)
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.
[XS8␣ ] Mode : lets you combine F , f, and ƒ terminals [SL16] Mode : for
terminals only
This unit corresponds to [XS8] and to [SL16].
÷ When all units in system control connection are set to [XS8] mode, set the SYSREM CONTROL selector switch on the rear to the
[XS8] side and connect.
÷ When all units in system control connection are set to [SL16] mode, set the SYSREM CONTROL selector switch on the rear to the
[SL16] side and connect.
SYSTEM CONTROL
No matter to which of the two terminals the connection is made, the use method is the same.
SPEAKERS
i
A or B : 4–16Ω, A and B : 8–16Ω
L R
L R
j
A
B
UNSWITCHED
100W MAX.
AC OUTLETS
SWITCHED TOTAL
200W MAX.
SYSTEM CONTROL selector switch
SL 16 XS-8
SIGNAL GND
PHONO CD TUNER TAPE
L
R
ƒ
REC PLAY REC PLAY
SYSTEM CONTROL
ƒ
SL 16 XS-8
MD
+––+
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for
Notes
Notes
system operations. If your equipment consists of this kind of combination, please do not connect any system control cords, Even without system control cords, normal operations can be carried out without affecting performance.
2. If your amp or receiver does not have a system control terminal, do not connect any system control cords to the system control terminals on the other compo­nents.
3. Do not connect system control cords to any components other than those speci­fied by KENWOOD. It may cause a malfunction and damage your equipment.
4. Be sure the system control plugs are inserted all the way in to the system control terminals.
The system control operations
Remote Control
The remote control supplied with this unit can also be used to control the other components in the system.
Automatic Operation (except [XR] equipment)
Automatically switches the input selector on the amp or receiver when you start playback from this unit.
Synchronized Recording (except [XR] equipment)
Lets you synchronize recording with the start of playback when recording from CD, MD, or LD.

Connection of speakers

Connect the speakers as shown below, ensuring that bare wires do not make contact with other terminals.
1 Strip coating.
KAF-3010R/1010 (En)
Speaker system A
2 Loosen.
3 Insert.
4 Secure.
RIGHT
SIGNAL GND
PHONO CD TUNER TAPE
L
R
REC PLAY REC PLAY
RIGHT
Speaker system B
Never short-circuit the + and – speaker cords.
•
If the left and right speakers are connected inversely or if the
•
speaker cords are connected with reversed polarity, the sound becomes unnatural with ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly.
SYSTEM CONTROL
ƒ
SL 16 XS-8
MD
LEFT
·ª·ª
SPEAKERS
i
A or B : 4–16Ω, A and B : 8–16Ω
j
R L
+––+
R L
A
B
·ª·ª
LEFT
Speaker impedance
When only one pair of speakers is connected to A or B speaker terminals, use the speakers having an impedance of 4 to 16 Ω. When two pairs of speakers are connected to both A and B terminals simultaneously, use the speakers having an impedance of 8 to 16 Ω. In this case, connecting a speaker having an impedance of less than 8 Ω may cause malfunction of the amplifier.
1 Connect all cords firmly. If connections are loose, there could be loss of sound or noise produced.
Notes
Notes
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplug­ging connection cords without removal of the power cord can cause malfunctions or damage to the unit.
3 Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit.

Controls and indicators

KAF-3010R/1010 (En)

Main unit

KAF-3010R KAF-1010
3
ON/STANDBY
POWER
ON OFF
142
ON/STANDBY
POWER
ON OFF
PHONES A SPEAKER B BASS TREBLE BALANCE
POWER
ON OFF
56 7 8 9 0
VOLUME CONTROL
MDTAPETUNERPHONOCD
INPUT SELECTOR
MIN MAX
MUTING LOUDNESS
SOURCE DIRECT
7
1 POWER switch (KAF-3010R) 0
Usually leave this switch to the on position. When the unit is not to be used for a long period of time, set the switch to the OFF position for safety.
2 ON/STANDBY key (KAF-3010R) 0
This key effective when the POWER key is set to the on (standby) position, and pressing this key turns power ON and off (standby).
3 Standby indicator (KAF-3010R) 4 POWER switch (KAF-1010) 0 5 BASS knob !
To adjust low frequencies.
6 TREBLE knob !
To adjust high frequencies.
7 INPUT indicator 0
An indicator lights for the source selected with the INPUT SELECTOR knob.
8 VOLUME CONTROL knob 0
Adjust the volume.
LR
thermally reactive advanced instantaneous transistor
TRAIT
&^%$#@!
9 SOURCE DIRECT indicator @ 0 SOURCE DIRECT key @
To listen to a source with high quality sound.
! PHONES jack @
Used for headphone listening.
@ SPEAKERS A/B switches 0
Press to select the A and/or B speaker systems.
# BALANCE knob !
Adjust the volume balance between left and right.
$ INPUT SELECTOR knob 0
Turn to select the input sources.
% MUTING key/indicator !
Mute the sound temporarily.
^ LOUDNESS key/indicator !
Use to emphasize deep bass sounds.
& Remote sensor (KAF-3010R only) 9
About the standby indicator (KAF-3010R only)
This unit has a standby indicator that lights to show that a small amount of current is being supplied to the unit in order to preserve the memory. This is called the Standby mode. When the Standby indicator is lit, the amplifier can be switched ON / STANDBY from the remote control.
KAF-3010R/1010 (En)
Remote control unit
(KAF-3010R only)
The part of the illustration designates keys that can be used to operate KENWOOD components connected with the system control. The rest of the illustration designates keys that have the same functions as the keys on the main unit.
DISC SKIP key
Only used for the Autochanger CD player.
TAPE operation keys
These keys perform the same operations as the correspond­ing keys on the cassettes deck. However, operations requir­ing simultaneous press-ing of two keys are not possible.
TUNER operation keys
MUTING key
Mute the sound temporarily.
VOLUME UP(%), DOWN(fi)
keys
Adjust the volume.
CD player operation keys
MD recorder operation keys
INPUT SELECTOR keys
AUX key does not function with
this unit.
4¢ 7 6
A
B
8¶1¡
4¢ 7 3
8¶fi
AUX TUNER CD
TAPE
POWER
CD
DISC SKIP
1¡
TAPE
273
MD
TUNER
P.CALL
MD PHONO
VOLUME
SOURCE DIRECT
REMOTE CONTROL UNIT
RC-A0300
CONTROL
%
MUTE
%
fi
POWER key
Use to switch the power ON/ STANDBY when the POWER
switch is turned ON.
SOURCE DIRECT key
To listen to a source with high quality sound.
Model: RC-A0300 Infrared ray system
Operation of remote control unit
(KAF-3010R only)
KAF-3010R/1010 (En)

Loading batteries

Remove the cover.
1
Insert batteries.
2
................................................................................................................
Insert two AA-size (R6 / SUM-3) batteries as indicated by the
•
polarity marking.
Close the cover.
3

Operation procedure

Pressing the POWER key on the remote control when the standby indicator is lit turns ON the power. After the power comes ON, press the key you want to operate.
Remote sensor
6 m
30°
30°
................................................................................................................
Operating range (approx.)
1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries.
Notes
Notes
2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light
When two operation keys on the remote control unit are pressed
•
Model: RC-A0300 Infrared ray system
sensor. In such a case, change the system installation position to prevent the malfunction.
successively, press each key securely reserving an interval of more than 1 second for each press.

Playing music

PHONES A SPEAKER B BASS TREBLE BALANCE
INPUT SELECTOR
MUTING LOUDNESS
ON OFF
MIN MAX
VOLUME CONTROL
MDTAPETUNERPHONOCD
SOURCE DIRECT
thermally reactive advanced instantaneous transistor
TRAIT
|{ |{
LR
REMOTE CONTROL UNIT
RC-A0300
4¢ 7 6
4¢ 7 3
8¶1¡
8¶fi
fi
%
%
1¡
273
A
DISC SKIP
B
AUX TUNER CD
TAPE
POWER
MD PHONO
MUTE
VOLUME
CONTROL SOURCE DIRECT
TUNER
P.CALL
CD
TAPE
MD
KAF-3010R/1010 (En)
KAF-3010R KAF-1010
POWER
ON OFF
10
Preparation
Set the MAIN POWER key to the - ON position.
•
When the POWER switch of the KAF-3010R is left ON at
•
all times, the power can be switched on and off with the remote control unit.

Normal playback

Turn the power ON. (KAF-3010R only)
1
Main unit
....................................................................................................
Remote control unit
Select the SPEAKERS switch setting.
2
Select the input source.
3
Main unit
ON/STANDBY
POWER
A SPEAKER B
INPUT SELECTOR
POWER
ON OFF
The figure shows an example for the KAF-3010R.
: Keys or controls to be used in this operation
................................................................................................................
A OFF, B OFF:
Set to this position when listening to the sound with stereo headphones only. Sound cannot be heard from the speakers.
A ON, B OFF:
Set to this position when listening to the sound with the speakers connected to the SPEAKERS A terminals.
A OFF, B ON:
Set to this position when listening to the sound with the speakers connected to the SPEAKERS B terminals.
A ON, B ON:
Set to this position when listening to the two pairs of speakers connected to both SPEAKERS A and SPEAKERS B terminals simultaneously.
................................................................................................................
One lights.
....................................................................................................
Remote control unit (KAF-3010R only)
AUX key does not function with this unit.
Play the selected source.
4
Adjust the volume.
5
Main unit
To decrease volume
....................................................................................................
Remote control unit (KAF-3010R only)
AUX TUNER CD
TAPE MD PHONO
To decrease volume
VOLUME CONTROL
%
VOLUME
CONTROL
fi
To increase volume
To increase volume
MDTAPETUNERPHONOCD
The indicator for the selected source lights.
÷
KAF-1010 : When the power is switched on, the input selector
÷
position is set to TUNER.
................................................................................................................
................................................................................................................

Sound adjustment functions

KAF-3010R/1010 (En)
The figure shows an example for the KAF-3010R.
To mute sound temporarily
Main unit
....................................................................................................
Remote control unit (KAF-3010R only)
MUTING
MUTE
Lights
CD
4¢ 7 6
DISC SKIP
A
1¡
TAPE
B
273
8¶1¡
MD
4¢ 7 3
TUNER
8¶fi
%
AUX TUNER CD
TAPE
POWER
REMOTE CONTROL UNIT
SOURCE DIRECT
MD PHONO
RC-A0300
P.CALL
MUTE
%
VOLUME
CONTROL
fi
ON OFF
PHONES A SPEAKER B BASS TREBLE BALANCE
|{ |{
LR
INPUT SELECTOR
MDTAPETUNERPHONOCD
VOLUME CONTROL
MIN MAX
MUTING LOUDNESS
thermally reactive advanced instantaneous transistor
SOURCE DIRECT
TRAIT
: Keys or controls to be used in this operation
When you press again, the volume returns to the original level
•
and the MUTING indicator goes out.
11
Adjusting the left/right sound balance
BALANCE
LR
To decrease the right sound
To decrease the left sound
Make sure the SOURCE DIRECT indicator is not lit. @
•
Adjusting the tone
BASS TREBLE
To adjust low frequencies
To adjust high frequencies
Make sure the SOURCE DIRECT indicator is not lit. @
•
Emphasizing deep bass (LOUDNESS)
Lets you emphasize the sound of deep bass when listening at low volumes.
LOUDNESS
Lights
Make sure the SOURCE DIRECT indicator is not lit. @
•
To cancel LOUDNESS
Press the LOUDNESS key again.
The LOUDNESS indicator goes out.
•
12
PHONES A SPEAKER B BASS TREBLE BALANCE
INPUT SELECTOR
MUTING LOUDNESS
ON OFF
MIN MAX
VOLUME CONTROL
MDTAPETUNERPHONOCD
SOURCE DIRECT
thermally reactive advanced instantaneous transistor
TRAIT
|{ |{
LR
REMOTE CONTROL UNIT
RC-A0300
4¢ 7 6
4¢ 7 3
8¶1¡
8¶fi
fi
%
%
1¡
273
A
DISC SKIP
B
AUX TUNER CD
TAPE
POWER
MD PHONO
MUTE
VOLUME
CONTROL SOURCE DIRECT
TUNER
P.CALL
CD
TAPE
MD
To listen through headphones
1 Set both of the SPEAKERS switches
Sound adjustment functions
KAF-3010R/1010 (En)
The figure shows an example for the KAF-3010R.
: Keys or controls to be used in this operation
to OFF.
A SPEAKER B
2 Plug headphones.
PHONES
3 Adjust the volume.
Main unit
To decrease volume
VOLUME CONTROL
MIN MAX
To increase volume
.....................................................................
To increase
%
VOLUME
CONTROL
fi
volume
To decrease volume
Remote control unit (KAF-3010R only)
Listening to high quality sound from a music source (SOURCE DIRECT)
Use this mode to avoid unnecessary circuitry during playback when you want to listen to high quality sound.
Main unit
SOURCE DIRECT
....................................................................................................
Remote control unit (KAF-3010R only)
SOURCE DIRECT
SOURCE DIRECT
Lights
Tone adjustment, balance and LOUDNESS do not work when
•
SOURCE DIRECT is ON (when the SOURCE DIRECT indicator is lit). The SOURCE DIRECT function takes precedence, regardless of
•
the source selected by the INPUT SELECTOR.
To cancel SOURCE DIRECT
Press the SOURCE DIRECT key again.
The SOURCE DIRECT indicator goes out.
•

Recording

PHONES A SPEAKER B BASS TREBLE BALANCE
INPUT SELECTOR
MUTING LOUDNESS
ON OFF
MIN MAX
VOLUME CONTROL
MDTAPETUNERPHONOCD
SOURCE DIRECT
thermally reactive advanced instantaneous transistor
TRAIT
|{ |{
LR
REMOTE CONTROL UNIT
RC-A0300
4¢ 7 6
4¢ 7 3
8¶1¡
8¶fi
fi
%
%
1¡
273
A
DISC SKIP
B
AUX TUNER CD
TAPE
POWER
MD PHONO
MUTE
VOLUME
CONTROL SOURCE DIRECT
TUNER
P.CALL
CD
TAPE
MD
KAF-3010R/1010 (En)
The figure shows an example for the KAF-3010R.
13
: Keys or controls to be used in this operation
To record a music source
1 Select the source to be recorded.
2 Put the cassette deck or MD recorder
in record-pause mode.
3 Play the source and start recording.
INPUT SELECTOR
One lights.
MDTAPETUNERPHONOCD
The indicator for the selected source lights.
÷
When TAPE is selected with the INPUT SELECTOR, recording is
÷
possible with the MD recorder. When MD is selected with the INPUT SELECTOR, recording is
÷
possible with the Tape deck.

In case of difficulty

KAF-3010R/1010 (En)
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative.
14
Operation to reset
The microcomputer may fall into malfunction (impossibility to operate, erroneous display, etc.) when the power cord is un­plugged while power is ON or due to an external factor. In this case, execute the following procedure to reset the microcom­puter and return it to normal condition.
Remote control unit (KAF-3010R only)
Symptom
Remote control operation is not possible
Batteries are exhausted.
•
The remote control unit is too far away
•
from the main system, controlling angle is too large, or there is an obstacle in be­tween. The audio cords and system control cords
•
are not connected properly. The source component to be operated
•
does not contain the tape(s) or CD. The POWER switch is set to OFF.
•
Amplifier
Symptom
Sound is not output.
The speaker cords are disconnected.
•
The VOLUME CONTROL is set to the
•
minimum position. MUTING is ON.
•
(The MUTING indicator is blinking) The SPEAKERS switches are set to OFF.
•
The system control cords are not fully con-
•
nected.
Set the POWER to OFF then, while holding down the SOURCE DIRECT key, set the POWER switch to ON.
•Please note that resetting the microcomputer clears the contents
stored in it and returns it to the condition when it left the factory.
Cause Remedy
Replace with new batteries. 9
•
Operate the remote control unit within the
•
controllable range.
Connect properly referring to “System
•
connection”. Place the tape(s) or CD in the source com-
•
ponent to be played. Set the POWER switch to ON. 0
•
Cause Remedy
Connect them properly referring to “Sys-
•
tem connection”.
Adjust the volume to a proper level.0
•
Press the MUTING key to OFF. !
•
Set the SPEAKERS switch(es) to ON.
•
Check the system control connections.
•
9
45
6
0
45
The standby indicator blinks and sound is not output. (KAF-3010R) The MUTING indicator blinks and sound is not output. (KAF-1010)
Sound is not output from one of the speakers.
Speaker cords are short-circuited.
•
The speaker cord is disconnected.
•
The BALANCE control is set to an extreme
•
position.
Turn the power off, eliminate the short-cir-
•
cuiting, then turn on the power again.
Connect it properly referring to “System
•
connection”.
Adjust the Left/Right balance. !
•
6
Speaker protection circuit
When this unit’s power is turned ON with the speaker cable short-circuited, the speaker protection functions. If the standby indicator blinks (KAF-3010R) or the MUTING indicator blinks (KAF-1010) and no sound occurs, turn the power OFF, remove the short-circuit, then turn the power ON again.
Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for
NoteNote
Note
they may deform the plastic components.

Specifications

Caution : Read this page carefully to ensure safe operation.
KAF-3010R/1010 (En)

KAF-3010R

Rated output power
(DIN) 1 kHz
at 8 Ω.............................................................. 70 W + 70 W
at 4 Ω.......................................................... 100 W + 100 W
(IEC/DIN) from 63 Hz to 12.5 kHz, 0.7 % T.H.D.
at 8 Ω.............................................................. 65 W + 65 W
at 4 Ω.......................................................... 100 W + 100 W
Effective output power
Except UK and Europe
(EIAJ) 1 kHz, 10 % T.H.D.
at 8 Ω.............................................................. 95 W + 95 W
at 4 Ω.......................................................... 130 W + 130 W
Damping factor ........................................................ 42 (50 Hz)
Total harmonic distortion
........................................... 0.04 % (20~20 kHz, 50 W, 4 Ω)
................................................... 0.01 % (1 kHz, 50 W, 4 Ω)
Frequency responce (IHF'78)
CD, TUNER, TAPE, MD ........... 5 Hz~85 kHz, +0 dB, -3 dB
PHONO 'RIAA' responce ...... 20 Hz~20 kHz, +1.0 dB, -1.0 dB
Maximum input level
PHONO (MM) .................... 100 mV, 0.5 % T.H.D. at 1 kHz
Signal to noise ratio
PHONO (MM) ............................................... 72 dB (IHF'66)
CD, TUNER, TAPE, MD ............................. 100 dB (IHF'66)
PHONO (MM) ........................ 60 dB (DIN, 50 mW output)
CD, TUNER, TAPE, MD ........ 60 dB (DIN, 50 mW output)
Input sensitivity/impedance
PHONO (MM) ............................................... 2.5 mV/33 kΩ
CD, TUNER, TAPE, MD .............................. 200 mV/47 kΩ
Tone control
BASS...................................................... ±10 dB (at 100 Hz)
TREBLE ..................................................±10 dB (at 10 kHz)
LOUDNESS control
VOLUME at -30 dB level ........................ +9 dB (at 100 Hz)
Output level/impedance
TAPE REC, MD REC ................................... 200 mV/2.7 kΩ

KAF-1010

Rated output power
(DIN) 1 kHz
at 8 Ω.............................................................. 40 W + 40 W
at 4 Ω.............................................................. 60 W + 60 W
(IEC/DIN) from 63 Hz to 12.5 kHz, 0.7 % T.H.D.
at 8 Ω.............................................................. 40 W + 40 W
at 4 Ω.............................................................. 60 W + 60 W
Effective output power
Except UK and Europe
(EIAJ) 1 kHz, 10 % T.H.D.
at 8 Ω.............................................................. 55 W + 55 W
at 4 Ω.............................................................. 75 W + 75 W
Damping factor ........................................................ 42 (50 Hz)
Total harmonic distortion
........................................... 0.06 % (20~20 kHz, 30 W, 4 Ω)
................................................... 0.01 % (1 kHz, 30 W, 4 Ω)
Frequency responce (IHF'78)
CD, TUNER, TAPE, MD ........... 5 Hz~85 kHz, +0 dB, -3 dB
PHONO 'RIAA' responce ...... 20 Hz~20 kHz, +1.0 dB, -1.0 dB
Maximum input level
PHONO (MM) .................... 100 mV, 0.5 % T.H.D. at 1 kHz
Signal to noise ratio
PHONO (MM) ............................................... 65 dB (IHF'66)
CD, TUNER, TAPE, MD ............................... 98 dB (IHF'66)
PHONO (MM) ........................ 60 dB (DIN, 50 mW output)
CD, TUNER, TAPE, MD ........ 60 dB (DIN, 50 mW output)
Input sensitivity/impedance
PHONO (MM) ............................................... 2.5 mV/33 kΩ
CD, TUNER, TAPE, MD .............................. 200 mV/47 kΩ
Tone control
BASS......................................................±10 dB (at 100 Hz)
TREBLE .................................................. ±10 dB (at 10 kHz)
LOUDNESS control
VOLUME at -30 dB level ........................ +9 dB (at 100 Hz)
Output level/impedance
TAPE REC, MD REC ................................... 200 mV/2.7 kΩ
15
General
Power consumption ...................................................... 200 W
AC outlet
SWITCHED ........................................ 2 (total 200 W max.)
UNSWITCHED............................................ 1 (100 W max.)
Dimensions ............................................................ W: 440 mm
H: 145 mm D: 400 mm
Weight (net) .................................................................. 8.3 kg
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without
NoteNote
Note
notice.
2. The full performance may not be exhibited in extremely coud location (under a water-freezing temperature).
General
Power consumption ...................................................... 140 W
Dimensions ............................................................ W: 440 mm
H: 145 mm D: 400 mm
Weight (net) .................................................................. 6.8 kg
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.
Model Serial Number
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use